Home

PJD6235/PJD6245/PJD6543w DLP Projector

1. changes the image height and vertical projection r angle Screw the adjuster foot to fine tune the C angle until the image is positioned where you want it If the projector is not placed on a flat surface or the screen and the projector are not perpendicular Fs to each other the projected image becomes Te trapezoidal To correct this situation see Correcting keystone on page 27 for details Do not look into the lens while the lamp is on The strong light from the lamp may cause damage to your eyes Auto adjusting the image In some cases you may need to optimize the picture quality To do this press AUTO on the projector or Auto Sync on the remote control Within 3 seconds the built in Intelligent Auto Adjustment function will re adjust the values of Frequency and Clock to provide the best picture quality The current source information will be displayed in the upper left corner of the screen for 3 seconds GF The screen will be blank while AUTO is functioning This function is only available when PC signal analog RGB is selected Fine tuning the image clarity 1 Adjust the projected image to the size 2 If necessary sharpen the image by that you need using the zoom ring rotating the focus ring Correcting keystone Keystoning refers
2. Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x00 0x69 Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x01 Ox6A User 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x02 0 6 Writ User 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x03 0x6C rite PC Gaming 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x04 0x6D Color mode ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x05 Ox6E Dynamic PC 0x06 0x14 0x00 0x04 0x00 0x34 0x12 Ox0B 0x06 Ox6F Dynamic Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 OxOB 0x07 0x70 Read Preset mode 0 0 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0 0 Ox6A Primary color R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 Ox6E Primary color G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 Ox6F Writ Primary color B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70 rite Primary color C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71 Primary Color Primary color M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72 Primary color Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73 Read redu 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0 00 0x12 0x10 Ox6F Writ Hue decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 Ox6F rite Hue Hue increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70 Read Hue 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70 Saturation 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0 70 decrease s Write s aturation saturation 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71 increase Read S
3. 5 Projector exterior view 6 Controls and functions 7 Positioning your projector 12 Choosing a 1 12 Projection dimensions 13 Connection 15 Connecting a computer or monitor 16 Connecting Video source devices 17 Operation 20 Starting up the projector 20 Using the menus 21 Utilizing the password function 22 Switching input signal 25 Adjusting the projected image 26 Magnifying and searching for details 27 Selecting the aspect ratio 28 Optimizing the image 31 Setting the presentation timer 35 Hiding the image 36 Locking control keys 36 Freezing the image 36 Operating in a high altitude eivironmeht ERES 36 Using the CEC function 37 Using the 3D functions 37 Controlling the projector through a LAN environment 39 Using the projector in standby mode 45 Shutting down the projector 46 Menu 47 Maintenance 57 Care of the projector
4. 57 Lamp information 58 Troubleshooting 64 Specifications 65 Projector specifications 65 Dimensions eee 67 Ceiling mount installation 67 Timing chart sess 68 Copyright information 71 Appendix 72 IR control table 72 RJ45 response table 74 RS232 command table 74 Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment However to ensure safe use of this product it is important that you follow the instructions mentioned in this manual and marked on the product Safety Instructions 1 Please read this manual before you operate your projector Save it for future reference 2 Donotlook straight at the projector lens during operation The intense light beam may damage your eyes 3 Refer servicing to qualified service personnel 4 Always open the lens shutter or remove the lens cap when the projector lamp is on 5 some countries the line voltage is NOT stable This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC but could fail if power cuts or surges of 10 volts occur In areas where the mains voltage may fluctuate or cut
5. 60 60 004 48 363 65 000 XGA 70 70 069 56 476 75 000 1024 x 768 XGA 75 75 029 60 023 78 750 XGA 85 84 997 68 667 94 500 XGA 120 Reduce Blanking 119 989 97 551 115 500 1280x720 1280x720 120 120 90 000 148 500 WXGA 60 59 810 49 702 83 500 1280 x 800 WXGA 75 74 934 62 795 106 500 WXGA 85 84 880 71 554 122 500 SXGA 60 60 020 63 981 108 000 1280 x 1024 SXGA 75 75 025 79 976 135 000 SXGA 85 85 024 91 146 157 500 1280 x 960 1280 x 960 60 60 000 60 000 108 1400X1050 5 60 59 978 65 317 121 750 1600 1200 UXGA 60 000 75 000 162 000 640x480 67Hz MAC13 66 667 35 000 30 240 832x624 75Hz MAC16 74 546 49 722 57 280 1152x870 75Hz MAC21 75 06 68 68 100 00 Cc Supported timing for 3D signal with Frame Sequential format Supported timing for 3D signal with Frame Sequential Top Bottom and Side by Side formats Copyright information Copyright Copyright 2012 rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of ViewSonic Corporation Disclaimer ViewSonic Corporation makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any
6. 0x14 0x00 0x04 0x00 0x34 0x11 0 0 0x01 0x69 Off Off On Read Quick Power 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69 Off status High Altitude 06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x69 Mode Off Write High Altitude High Altitude 006 0x14 0x00 0x04 0x00 0x34 0x11 OxOC 0x01 Ox6A Mode Mode On Read High Altitude 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 OxOC Ox6A Mode status ae 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 Ox6D Write Lamp Mode Lamp Mode 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 Ox6E Economic Read ses iam 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 Ox6E Writ Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84 rite Message Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85 Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85 Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 Ox5E Writ Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 Ox5F rite Projector Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Position Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Read Projector 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 Ox5F position status OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 Ox7E Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0 01 Ox7F Frame 0x06 0x14 0x00 0x04 0 00 0x34 0x12 0x20 0x02 0x80 Write Sequential 3D Sy c Frame Packing 0 06 0x14 0x00 0x04 0x00 0x34 0x12
7. Manually corrects distorted images resulting from an angled projection 5 Al vI Selects the desired menu items and makes adjustments 6 8 10 Enter Enacts the selected On Screen Display OSD menu item My Button Allows user to define a short cut key on the remote control and the function item is selected in OSD menu Menu Turns on the On Screen Display OSD menu 8 Performs the same function as the left mouse button when the mouse mode is activated B Performs the same function as the right mouse button when the mouse mode is activated Mouse Switches between the normal and mouse modes Page Up Page Down Bj BJ active after pressing Mouse An icon appears on the screen to indicate the activation of the mouse mode 12 13 14 15 16 17 18 Magnify 19 Displays the zoom bar that magnifies or reduces the projected picture size 20 Lock Activates or deactivates panel key lock Freeze 21 Freezes the projected image Pattern Displays embedded test pattern Blank Hides the screen picture DynamicEco Decreases the power consumption of the lamp by up to 30 23 CFT It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes If the projector is resumed by using the 4 Smart Restart feature this function can be executed immediately 25 Auto Sync Automatically determines the b
8. After making the adjustments press the Send button and the data will be saved for the projector vi Press Exit to go back to the remote network operation page Please pay attention to the limitation of input length including space and other punctuation keys in the list blow Category Item Input Length Maximam eo Characters IP Address 16 Crestron Control IP ID 4 Port 5 Projector Name 32 Projector Location 32 Assigned To 32 DHCP Enabled N A IP Address 16 Network Configuration Subnet Mask 16 Default Gateway 16 DNS Server 16 Enabled N A User Password New Password 26 Confirm 26 Enabled N A Admin Password New Password 26 Confirm 26 3 info page displays the information and status of this projector Contact IT Help Projector Information Projector Status morus p a cone Firmware Version Projector Position Wac address Resolution Lamp Hours Lamp Mode Worms AAA Assigned To Error Status Press Exit to so back to the remote network lt es d Expansion Options operation page 4 After pressing the button Contact IT Help the HELP DESK window will appear in the upper right corner of the screen You will be able to deliver messages to RoomView software administrators users who connect to the same local area network For more information visit http www crest
9. Alert Setting Email Setting SMTP Setting Alert Condition Serer as L coc enses Subject Password aM From Lamp Time Alert Issue Test Mail 5 The Crestron e Control page displays the Crestron e Control user interface See About Crestron e Control on page 42 for details Please pay attention to the limitation of input length including space and other punctuation keys in the list blow Maximum Number Category Item Input Length St Characters DHCP Manual N A IP Address XXX XXX XXX XXX Subnet Mask XXX XXX XXX XXX Network Gateway XXX XXX XXX XXX DNS Server XXX XXX XXX XXX Network Settings AMX device discovery N A Administrator N A Password New Password 4 Confirm Password 4 SysLocation 22 SNMP SysName 22 SysContact 22 To 40 Email Setting 0 Subject 40 From 40 Server 30 SMTP Setting User Name 21 Email Alert Password 14 Fan Error N A Lamp Error N A Alert Condition Over Temperature N A Lamp Time Alert N A Submit N A Issue Test Mail N A CF gt lt 1 are prohibited About Crestron e Control 1 The Crestron e Control page provides a variety of virtual keys to control the projector or adjust the projected pictures Tools Info Contact IT Help SourceList You can press lt gt to reveal more buttons m lt i These buttons function
10. ViewSonic 986 PJD6235 PJD6245 PJD6543w DLP Projector User Guide IMPORTANT Please read this User Guide to obtain important information on installing and using your product in a safe manner as well as registering your product for future service Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation which is also found on our web site at http www viewsonic com in English or in specific languages using the Regional selection box in the upper right corner of our website Antes de operar su equipo lea cu idadosamente las instrucciones en este manual Model No VS14931 VS14933 VS14934 Compliance Information FCC Statement This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfe
11. C P 62040 Cuernavaca Morelos Tel 01 777 3180579 01 777 3124014 E Mail aquevedo 2 compusupportcva com Guadalajara Jal SERVICRECE S A de C V Av Ni os H roes 2281 Col Arcos Sur Sector Ju rez 44170 Guadalajara Jalisco Tel 01 52 33 36 15 15 43 E Mail mmiranda servicrece com Monterrey Global Product Services Mar Caribe 1987 Esquina con Golfo P rsico Fracc Bernardo Reyes CP 64280 Monterrey N L M xico Tel 8129 5103 E Mail aydeem gps1 com mx Oaxaca Oax CENTRO DE DISTRIBUCION Y SERVICIO S A de C V Murguia 708 P A Col Centro 68000 Oaxaca Tel 01 52 95 15 15 22 22 Fax 01 52 95 15 13 67 00 E Mail gpotai2001 hotmail com FOR USA SUPPORT ViewSonic Corporation 381 Brea Canyon Road Walnut CA 91789 USA Tel 800 688 6688 English 866 323 8056 Spanish Fax 1 800 685 7276 E Mail http www viewsonic com Projector Mexico Warranty Term Template In UG VSC TEMP 2006 ViewSonic
12. Menu system Please note that the on screen display OSD menus vary according to the signal type selected The menu items are available when the projector detects at least one valid signal If there is no equipment connected to the projector or no signal detected limited menu items are accessible Main menu Sub menu Options Screen Color Off Blackboard Greenboard Whiteboard Auto 4 3 16 9 16 10 PJD6543w only Wide PJD6543w only Anamorphic PJD6235 PJD6245 only Aspect Ratio Keystone Position Phase 1 H Size DISPLAY om Auto Off Frame Sequential 3D Sync Frame Packing Top Bottom 3D Settings d Side by Side 3D Sync Invert Disable Invert Primary Color R G B C M Y Color Hue Management Saturation Gain PC source Brightest PC ViewMatch Movie Dynamic Color Mode PC Dynamic Movie User 1 User 2 Video source Brightest Gaming ViewMatch Movie Dynamic Movie User 1 User 2 PC source Brightest PC ViewMatch Movie Dynamic Reference Mode PCIDynamic Movie Video source Brightest Gaming ViewMatch Movie 2 Dynamic Movie PICTURE Brightness Contrast Color Tint Sharpness Brilliant Color On Off Color Temperature T1 T2 T3 TA Save Settings Main menu Sub menu Options Quick Auto Search Off On HDMI Format RGB YUV Auto HDMI Range Enhanced Normal Disable 5 min 10 min 15 min 30 DynamicEco Timer min 3 SOURCE smart Restart OfflOn Pattern Offl01 02 03 04 05 Projection Projector Position 3D SynciLamp Mod
13. reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic For Your Records Product Name PJD6235 PJD6245 PJD6543w ViewSonic DLP Projector Model Number VS14931 VS14933 VS14934 Document Number PJD6235 PJD6245 PJD6543w_UG_ENG Rev 1A 12 04 12 Serial Number Purchase Date Product disposal at end of product life The lamp in this product contains mercury which can be dangerous to you and the environment Please use care and dispose of in accordance with local state or federal laws ViewSonic respects the environment and is committed to working and living green Thank you for being part of Smarter Greener Computing Please visit ViewSonic website to learn more USA 4 Canada http www viewsonic com company green recycle program Europe http www viewsoniceurope com uk support recycling information Taiwan http recycle epa gov tw recycle index2 aspx Table of contents Important safety instructions 2 Introduction 4 Projector features 4 Shipping contents
14. 0x20 0x03 0x81 Top Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82 Side by Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83 Read 3D Sync Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 Ox7F m Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 Ox7F rite On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80 3D Sync Invert Read 30 2 0x07 0x14 0 00 0 05 0 00 0x34 0 00 0 00 0x12 0x21 0 80 contras 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60 decrease C Write Contrast 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61 Increase Read Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61 Brightness 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61 decrease Write I Brightness Brightness 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62 increase Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62 Aspect ratio 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 EUM 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 A ial Write spect ratio i R raio 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68 Anamorphic Read Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63 Auto Adjust xecute 0x06 0x14 0
15. 3 5 80 2 0 2 58 102 2 84 112 108 42 0 0 2 43 96 2 68 105 102 40 10 2 4 0 2 74 108 3 01 119 114 45 11 4 4 5 0 0 3 04 120 3 35 132 127 50 12 7 5 0 0 0 3 65 144 4 02 158 152 60 15 2 6 0 0 0 4 56 180 5 02 198 191 75 19 1 7 5 0 0 6 09 240 6 70 264 254 100 25 4 10 0 0 0 7 61 300 8 37 329 318 125 31 8 12 5 0 0 9 13 359 10 04 395 381 150 38 1 15 0 90 2 3 2 90 114 3 19 126 121 100 2 5 3 23 127 3 55 140 135 120 3 0 3 87 152 4 26 168 162 150 3 8 4 84 191 5 32 210 202 200 5 1 6 45 254 7 10 279 269 106 250 6 4 8 06 318 8 87 349 337 132 300 7 6 9 68 381 10 65 419 404 159 CT There is 3 tolerance among these numbers due to optical component variations It is recommended that if you intend to permanently install the projector you should physically test the projection size and distance using the actual projector in situ before you permanently install it so as to make allowance for this projector s optical characteristics This will help you determine the exact mounting position so that it best suits your installation location Connection When connecting a signal source to the projector be sure to 1 Turn all equipment off before making any connecti
16. 4a compatible device the projector detects the signal for 3D Sync information and once detected it projects images in 3D format automatically In other cases you may need to manually select a 3D Sync format for the projector to project 3D images correctly To select a 3D Sync format 1 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the DISPLAY menu is highlighted 2 Press to highlight 3D Settings and press MODE ENTER on the projector or Enter on the remote control 3 Press x to highlight 3D Sync and press MODE ENTER on the projector or Enter on the remote control 4 Press v to select a 3D Sync setting according to the table below and then press MODE ENTER on the projector or Enter on the remote control to confirm When the 3D Sync function is on brightness level of the projected image will decrease The Color Mode cannot be adjusted Zoom can only magnify the pictures to limited sizes If you discover the inversion of the 3D image depth set the 3D Sync Invert function to Invert to correct the problem Controlling the projector through a LAN environment The projector supports Crestron software With correct settings for the LAN Control Settings menu you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network An example of connection
17. 7 223 6 2 245 229 90 23 9 0 5 7 223 6 2 245 171 68 51 4 20 3 34 134 3 7 147 103 3 8 149 42 163 114 gt 200 5 1 7 5 297 8 3 327 305 120 30 12 0 7 5 297 8 3 327 229 90 68 6 27 0 250 6 4 9 4 371 10 4 409 381 150 38 15 0 9 4 371 10 4 409 286 113 85 7 33 8 300 7 6 11 3 446 12 5 490 457 180 46 18 0 11 3 446 12 5 490 343 135 102 9 40 5 PJD6543w 16 10 image on a 16 10 screen 16 10 image on a 4 3 screen e Screen f Center of lens 16 10 image on a 16 10 Screen 16 10 image on a 4 3 Screen b Projection distance c Image d Vertical b Projection distance c Image d Vertical inch m m inch height offset m inch height offset min max cm inch inch max cm inch cm inch 30 0 8 0 97 38 1 06 42 40 16 0 0 0 91 36 1 00 40 38 15 3 8 1 5 40 1 0 1 29 51 1 42 56 54 21 0 0 1 22 48 1 34 53 51 20 5 1 2 0 50 1 3 1 61 64 1 77 70 67 26 0 0 1 52 60 1 67 66 64 25 6 4 2 5 60 1 5 1 94 76 2 13 84 81 32 0 0 1 83 72 2 01 79 76 30 7 6 3 0 70 1 8 2 26 89 2 48 98 94 0 0 2 13 84 2 34 92 89 35 8 9
18. Aspect repeatedly to select an aspect ratio to suit the format of the video signal and your display requirements Using the OSD menu 1 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the DISPLAY menu is highlighted 2 Press V to highlight Aspect Ratio uy Press lt gt to select an aspect ratio to suit the format of the video signal and your display requirements About the aspect ratio In the pictures below the black portions are inactive areas and the white portions are active areas OSD menus can be displayed on those unused black areas 1 Auto Scales an image proportionally to fit the projector s native resolution in its horizontal width This is suitable for the incoming image which is neither in 4 3 nor 16 9 and you want to make most use of the screen without altering the image s aspect ratio 4 3 Scales an image so that it is displayed in the center of the screen with a 4 3 aspect ratio This is most suitable for 4 3 images like computer monitors standard definition TV and 4 3 aspect DVD movies as it displays them without aspect alteration 16 9 Scales an image so that it is displayed in the center of the screen with a 16 9 aspect ratio This is most suitable for images which are already in a 16 9 aspect like high definition TV as it displays them without aspect alteration 16 10 PJD6543w only Scales an image so that it is displayed in the cen
19. Change Password menu 2 Press MODE ENTER on the projector or Enter on the remote control The message INPUT CURRENT PASSWORD is displayed 3 Press and hold AUTO on the projector or Auto Sync on the remote control for 3 seconds The RECALL PASSWORD Please write down the recall code projector will display a coded number on the P screen 4 Write down the number and turn off your proie oce 1 MENU Exit 5 Seek help from the local service center to decode the number You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector Changing the password 1 Open the OSD menu and go to the SYSTEM SETTING ADVANCED gt Security Settings gt Change Password menu 2 Press MODE ENTER on the projector or Enter on the remote control The message INPUT CURRENT PASSWORD is displayed 3 Enter the old password If the password is correct another message INPUT NEW PASSWORD is displayed If the password is incorrect the password error message is displayed lasting for three seconds and the message INPUT CURRENT PASSWORD is displayed for your retry You can press MENU EXIT on the projector or Exit on the remote control to cancel the change or try another password 4 Enter a new password Confirm the new password by re entering the new password 6 You have successfully assigned a new password to the projector Remember
20. Configuring the LAN Control Settings If you are in a DHCP environment 1 Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port 2 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the SYSTEM SETTING BASIC menu is highlighted 3 Press V to highlight LAN Control Settings and press MODE ENTER on the projector or Enter on the remote control The LAN Control Settings page is displayed 4 Press V to highlight DHCP and press lt gt to select On Press v to highlight Apply and press MODE ENTER on the projector or Enter on the remote control 6 Please wait for around 15 20 seconds and then re enter the LAN Control Settings page The Projector IP Address Subnet Mask Default Gateway and DNS Server settings will be displayed Note down the IP address displayed in the Projector IP Address row CT Ifthe Projector IP Address still does not appear contact your network administrator Ifthe RJ45 cables are not properly connected the Projector IP Address Subnet Mask Default Gateway and DNS Server settings will display 0 0 0 0 Make sure the cables are properly connected and perform the procedures above again Ifyou need to connect to the projector in its standby mode set Power Saving to Off If you are in a non DHCP environment 1 Repeat steps 1 3 above 2 Press v to highlight DHCP and press lt gt to select O
21. Please contact your dealer for assistance Troubleshooting The projector does not turn on Cause Remedy There is no power from the power cord Plug the power cord into the AC inlet on the projector and plug the power cord into the power outlet If the power outlet has a switch make sure that it is switched on Attempting to turn the projector on again during the cooling process Wait until the cooling down process has completed O No picture Cause Remedy The video source is not turned on or connected correctly Turn the video source on and check that the signal cable is connected correctly The projector is not correctly connected to the input signal device Check the connection The input signal has not been correctly selected Select the correct input signal with the SOURCE key on the projector or remote control Blurred image Cause Remedy The projection lens is not correctly focused Adjust the focus of the lens using the focus ring The projector and the screen are not aligned properly Adjust the projection angle and direction as well as the height of the projector if necessary Remote control does not work Cause Remedy The battery is out of power Replace the battery with a new one There is an obstacle between the remote control and the projector Remove the obstacle You are too far aw
22. See Indicators on page 63 for details The following lamp warning displays will remind you to change the lamp Status Message Install a new lamp for optimal performance If the projector is normally run with Economic selected See Setting Lamp Mode as Economic on page 58 you may continue to operate the projector until the next hour lamp warning appears Notice Order Replacement Lamp Lamp gt Hours A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time Replace Lamp Soon Lamp gt Hours It is strongly recommended that you replace the lamp at this age The lamp is a consumable item The lamp brightness diminishes with use This is normal lamp behavior You can replace the lamp whenever you notice that the brightness level has significantly diminished If the lamp is not replaced beforehand it must be replaced when you see this message Lamp gt Hours Lamp usage time exceeded OK The lamp MUST be replaced before the projector will operate normally Notice Out of Lamp Usage Time Replace lamp refer to User Manual Then reset lamp timer OK Replacing the lamp To prepare a new lamp contact your dealer and tell the lamp type number Type number RLC 078 PJD6235 PJD6245 Type number RLC 085 PJD6543w NWARNING Hg Lamp contains mercury Manage in accordance with local disposal laws See www lamprecyc
23. by the manufacturer or sold with the unit When a cart is used use caution when moving the cart unit combination to avoid injury from tipping over Unplug this unit when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the unit has been damaged in any way such as if the power supply cord or plug is damaged if liquid is spilled onto or objects fall into the unit if the unit is exposed to rain or moisture or if the unit does not operate normally or has been dropped Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002 95 EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Directive and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee TAC as shown below Proposed Maximum Actual Concentration Concentration Lead Pb 0 1 lt 0 1 Cadmium Cd 0 01 lt 0 01 Hexavalent Chromium 6 0 1 0 196 Polybrominated biphenyls PBB 0 196 lt 0 196 Polybrominated diphenyl ethers PBDE 0 196 lt 0 196 Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below Examples of exempted components are 1 Leadin glass of cathode ray tubes electronic components fluorescent tubes and elec
24. chemical detergents These can damage the case Storing the projector If you need to store the projector for an extended time please follow the instructions below Make sure the temperature and humidity of the storage area are within the recommended range for the projector Please refer to Specifications on page 65 or consult your dealer about the range Retract the adjuster feet Remove the battery from the remote control Pack the projector in its original packing or equivalent Transporting the projector It is recommended that you ship the projector with its original packing or equivalent Lamp information Getting to know the lamp hour When the projector is in operation the duration in hours of lamp usage is automatically calculated by the built in timer To obtain the lamp hour information 1 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the SYSTEM SETTING ADVANCED menu is highlighted 2 Press to highlight Lamp Settings and press MODE ENTER on the projector or ENTER on the remote control The Lamp Settings page is displayed 3 You will see the Equivalent lamp hour information on the menu 4 To leave the menu press MENU EXIT on the projector or Exit on the remote control You can also get the lamp hour information on the INFORMATION menu Extending lamp life The projection lamp is a consumable item To keep the lamp life as long as possible you can do
25. during projector start up Message Function Description Sets the language for the On Screen Display OSD menus See Language Using the menus on page 21 for details Projector The projector can be installed on a ceiling or behind a screen or with one or more mirrors See Choosing a location on page 12 for Position details Auto Power Allows the projector to turn off automatically if no input signal is Off detected after a set period of time See Setting Auto Power on page 58 for details gt Blank Timer 2 Sets the image blank time when the Blank feature is activated once elapsed the image will return to the screen See Hiding the image m Timer on page 36 for details m Sleep Timer m Allows the projector to turn off automatically after a set period of 3 time if the incoming signal is present or not Q Panel Key Disables or enables all panel key functions except POWER on Lock the projector and keys on the remote control See Locking control Oo 3 3 E Selecting On displays the current information on the screen when the projector is detecting or searching for a signal LAN Control See Controlling the projector through a LAN environment on page Settings 39 for details Standby E See Using the projector in standby mode on page 45 for details Settings donis T See Using the function on page 37 for details Function Description High Alt
26. for reference only and may differ from the actual design 1 Enter the address of the projector in the address bar of your browser and press Enter Crestron_TI Microsoft Internet Explorer Ele yew Favorites Too Hep Back Gi ser Favorites E a es 10 32 30 156 2 The main page of the Network Control appears 86 ViewSonic Network Control 5 UserName Administrator Password C Accessing to Network Settings or Email Alert page requires Administrator password The default password is 0000 3 This page allows you to make adjustments to the AMX and SNMP settings In the AMX device discover row when ON is selected the projector can be detected by controllers of AMX connected to the same network For the Details of AMX Device Discovery visit the AMX web site at http www amx com e Network Email Alei DHCP O Manual Crestron e Control IP Address 10 82 30 Subnet Mask Gateway DNS Server AMX device discover ON OFF 846 ViewSonic Network Control Password SNMP Administrator 9 Enable O Disable SysLocation New Password SysName Confirm Password SysContact Submit 4 If your projector is connected to a network which supports Simple Mail Transfer Network Settings S88 ViewSonic Network Control Protocol SMTP you can configure it to alert you via email on significant events
27. mono audio projector Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices To connect the projector to an HDMI device 1 2 CT Take an HDMI cable and connect one end to the HDMI output port of the video device Connect the other end of the cable to the HDMI input port on the projector In the unlikely event that you connect the projector to a DVD player via the projector s HDMI input and the projected picture displays wrong colors please change the color space to YUV See Changing HDMI input settings on page 25 for details The projector is only capable of playing mixed mono audio even if a stereo audio input is connected See Connecting audio on page 17 for details Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available If so you can continue with this procedure If not you will need to reassess which method you can use to connect to the device To connect the projector to a Component Video source device 1 Cr Take a VGA D Sub Component adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device Match the color of the plugs to the color of the sockets green to green blue to blue and red to red Connect the other end of the VGA D Sub Component adaptor cable with a
28. the following settings via the OSD menu Setting Lamp Mode as Economic Using Economic mode reduces system noise and power consumption by 20 If the Economic mode is selected the light output will be reduced and result in darker projected pictures Setting the projector in Economic mode also extends the lamp operation life To set Economic mode go into the SYSTEM SETTING ADVANCED gt Lamp Settings gt Lamp Mode menu and press lt gt Setting Auto Power Off This function allows the projector to turn off automatically if no input source is detected after a set period of time to prevent unnecessary waste of lamp life To set Auto Power Off go into the SYSTEM SETTING BASIC gt Auto Power Off menu and press lt gt If the preset time lengths are not suitable for your presentation select Disable The projector will not automatically shut down in a certain time period Timing of replacing the lamp When the LAMP indicator light lights up red or a message appears suggesting it is time to replace the lamp please install a new lamp or consult your dealer An old lamp may cause a malfunction in the projector and in some instances the lamp may explode N caution The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot Turn the power off and let the projector cool for 45 minutes If the LAMP or TEMP indicator still lights up after turning the power back on please contact your dealer
29. to enter the new password next time the projector is started 7 leave the OSD menu press MENU EXIT on the projector or Exit on the remote control Un T The digits being input will be displayed as asterisks on screen Write your selected password down here in this user manual in advance or right after the password is entered so that it is available to you should you ever forget it Password Keep this user manual in a safe place Disabling the password function To disable password protection go back to the SYSTEM SETTING ADVANCED gt Security Settings gt Power On Lock menu after opening the OSD menu system Select Off by pressing lt gt The message INPUT PASSWORD is displayed Enter the current password If the password is correct the OSD menu returns to the Security Settings page with Off shown in the row of Power On Lock You will not have to enter the password next time you turn on the projector If the password is incorrect the password error message is displayed lasting for three seconds and the message INPUT PASSWORD is displayed for your retry You can press MENU EXIT on the projector or Exit on the remote control to cancel the change or try another password Though the password function is disabled you need to keep the old password in hand should you ever need to re activate the password function by entering the old password Switching input signal The projector can be connected t
30. warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damages based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercial loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise 3 Any claim against the customer by any other party Effect of local law This warranty gives you specific legal rights and you may also have other rights which vary from local authority Some local governances do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and service on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer The warranty period for this product in mainland China Hong Kong Macao and Taiwan Excluded is subject to the terms and conditions of the Maintenance Guarantee Card F
31. with the lamp cover removed Resetting the lamp timer 13 After the startup logo open the On Screen Display OSD menu 14 Go to the SYSTEM SETTING ADVANCED gt Lamp Settings menu Press MODE ENTER on the projector or ENTER on the remote control The Lamp Settings page is displayed 15 Press to highlight Reset lamp timer and press MODE ENTER on the projector or ENTER on the remote control A warning message is displayed asking if you want to reset the lamp timer 16 Highlight Reset and press MODE ENTER on the projector or ENTER on the remote control The lamp time will be reset to 0 A CAUTION Do not reset if the lamp is not new or replaced as this could cause damage Reset Lamp Timer Indicators Light Status amp Description POWER TEMP LAMP Power events Blue Flashing Off Off Stand by mode Blue Off Off Powering up Blue Off Off Normal operation Blue Flashing Off Off Normal power down cooling Lamp events Blue Off Red The projector needs 60 seconds to cool down Flashing The projector has shut down automatically If you try Off Off Red to re start the projector it will shut down again Please contact your dealer for assistance Blue Off Red CW start fail 30sec Thermal events Off Red Off The projector has shut down automatically If you try Off Red Red to re start the projector it will shut down again Purple Red Red
32. 0 60 000 108 1400X1050 5 60 59 978 65 317 121 750 1600 1200 UXGA 60 000 75 000 162 000 640x480 67Hz MAC13 66 667 35 000 30 240 832x624 7 5Hz MAC16 74 546 49 722 57 280 1152x870 75Hz MAC21 75 06 68 68 100 00 Supported timing for 3D signal with Frame Sequential format e Supported timing for 3D signal with Frame Sequential Top Bottom and Side by Side formats Supported timing for Component YPbPr input Horizontal Vertical Dot Clock Timing Resolution frequency Frequency Frequency KHz Hz MHz 480i 720 x 480 15 73 59 94 13 5 480p 720 x 480 31 47 59 94 27 576i 720 x 576 15 63 50 13 5 576p 720 x 576 31 25 50 27 720 50p 1280 x 720 37 5 50 74 25 720 60p 1280 x 720 45 00 60 74 25 1080 50i 1920 x 1080 28 13 50 74 25 1080 60i 1920 x 1080 33 75 60 74 25 1080 50P 1920 x 1080 56 25 50 148 5 1080 60P 1920 x 1080 67 5 60 148 5 Supported timing for 3D signal with Frame Sequential format Supported timing for Video and S Video inputs Horizontal Frequency Vertical Frequency Color sub carrier Video mode kHz Hz Frequency MHz NTSC 15 73 60 3 58 PAL 15 63 50 4 43 SECAM 15 63 50 4 25 or 4 41 PAL M 15 73 60 3 58 PAL N 15 63 50 3 58 PAL 60 15 73 60 4 43 NTSC4 43 15 73 60 4 43 Supported timing for 3D signal with Frame Sequential format Suppo
33. 14 0x00 0x04 0x00 0x34 0x15 0x00 0 0 0x6D Co amp tina 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 OxOd 0x6E Portugu s 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 OxOe Ox6F 0 06 0x14 0x00 0x04 0x00 0x34 0x15 0 00 OxOf 0x70 Polski 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71 Suomi 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72 Lydi 0 06 0x14 0x00 0x04 0x00 0x34 0x15 0 00 0x12 0x73 Indonesian 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74 RA 0 06 0x14 0 00 0x04 0x00 0x34 0x15 0 00 0x14 0x75 Read Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62 Write Reset Lamp 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62 usage hour Lamp Time L Read id a 0x07 0x14 0 00 0x05 0 00 0x34 0x00 0 00 0x15 0 01 0x63 Error status Read Read error 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 OxOD 0x66 status Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 Ox2B 0x00 0x88 Write 0 06 0 14 0 00 0 04 0 00 0 34 0 11 0 2 0 01 0 89 status 0 07 0 14 0 00 0 05 0 00 0 34 0 00 0 00 0 11 0 2 0 89 E S Saj 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D Write antc Brilliant Color uie olor 0x14 0x00 0x04 0x00 0x34 0x12 OxOF 0x01 0x6E Read Bman color 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 OxOF 0x6E 0x06 0x14 0x00 0x04 0x00 0x34 OxOC 0x48 0x00 OxAO Write Remote Remote Control 006 0x14 0x00 0x04 0x00 0x34 OxO
34. 64 9B Video NEC 83 F4 66 99 Source NEC 83 F4 7D 82 Color Mode NEC 83 F4 9E 61 Up 5 NEC 83 F4 67 98 Left NEC 83 F4 69 96 Enter NEC 83 F4 6B 94 Right NEC 83 F4 6A 95 Down KeyS NEC 83 F4 68 97 Menu NEC 83 F4 6C 93 My Button NEC 83 F4 6D 92 Exit NEC 83 F4 6E 91 Mouse L key NEC 83 F4 38 C7 Mouse R key NEC 83 F4 39 C6 PgUp NEC 83 F4 5C A3 PgDn NEC 83 F4 5D A2 Mouse NEC 83 F4 9B 64 Magnify NEC 83 F4 99 66 Volume NEC 83 F4 5A A5 Volume NEC 83 F4 5B A4 Panel Key Lock 83 F4 5E A1 Freeze NEC 83 F4 61 9E Pattern NEC 83 F4 7E 81 Blank NEC 83 F4 62 9D Mute NEC 83 F4 9D 62 DynamicEco NEC 83 F4 7F 80 Timer NEC 83 F4 9C 63 Aspect NEC 83 F4 9A 65 RJ45 response table Normal gt ACK 0x03 0x14 0x00 0x00 0x00 0x14 Write Incorrect gt ERROR ACK 0x00 0x14 0x00 0x00 0x00 0x14 Timeout gt 100 N A BYTEO BYTE1 2 4 BYTES BYTE6 BYTE7 N BYTE N 1 0x05 0x14 0x00 LSB MSB 0x00 0x00 Data Checksum Read Ex1 Read power status 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18 Ex2 Read brightness 0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x32 0x00 0x4A 50 Ex3 Read lamp hours 0x05 0x14 0x00 0x06 0x00 0x00 0x00 0x28 0x00 40 0x00 0x00 0x42 CT The RJ45 commands can o
35. A signal when the COMPUTER IN 1 and COMPUTER OUT sockets are correctly connected to devices The projector outputs the signal received only from COMPUTER IN 1 Active Audio Out Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are correctly connected to devices Quick Power Off Selecting On enables the function and the projector will not enter the cooling process after being shut down Selecting Off disables the function and the projector will enter normal cooling process after being shut down CZ Ifyou attempt to restart the projector right after it s been turned off it may not be turned on successfully and will rerun its cooling procedure When Off is selected the Smart Restart function will be automatically turned off Shutting down the projector 1 Press 5 POWER and a confirmation message is displayed prompting you If you don t respond in a few seconds the message will disappear 2 Press D POWER a second time 3 Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time N CAUTION protect the lamp the projector will not respond to any commands during the cooling process To shorten the cooling time you can also activate the Quick Power Off function See Quick Power Off on page 45 for details Donotunplug the power cord before the projector shutdown sequence is complete Menu operation
36. C 0x48 0x01 OxA1 Control code code B Read Remote Control 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0 00 OxOC 0x048 code status OxA1 Customer Support For technical support or product service see the table below or contact your reseller Note You will need the product serial number Country Region Website Telephone Email Australia New Zealand www viewsonic com au AUS 1800 880 818 NZ 0800 008 822 service au viewsonic com T Toll Free 1 866 463 4775 Canada www viewsonic com T Toll 1 424 233 2533 service ca viewsonic com F 1 909 468 3757 Europe a www viewsoniceurope com uk support call desk Hong Kong www hk viewsonic com T 852 3102 2900 service hk viewsonic com India www in viewsonic com T 1800 266 0101 service in viewsonic com Korea www kr viewsonic com T 080 333 2131 service kr viewsonic com pos America www viewsonic com la T 0800 4441185 soporte viewsonic com Argentina Latin America Chile www viewsonic com la T 1230 020 7975 soporte viewsonic com Latin America Columbia www viewsonic com la T 01800 9 157235 soporte viewsonic com Latin America Mexico www viewsonic com la T 001 8882328722 soporte viewsonic com Renta y Datos 29 SUR M rida Yucat n Tel 01 999 925 com la soporte index htm Mexico 721 COL LA PAZ 72160 PUEBLA PUE Tel 01 222 891 55 77 CON 10 LINEAS
37. C2 CC3 CCA Normal Economic 1 240 minutes Always 1 min 2 min 3 min Never Top Left Bottom Left Top Right Bottom Right Count Down Count Up On Off On Off AIB Reset Cancel Main menu Sub menu Options 6 INFORMATION Current System Status Source Color Mode Resolution Color System Equivalent Lamp Hour MAC Address Description of each menu Function Description Screen Color Corrects the projected picture s color when the projection surface is not white See Using Screen Color on page 32 for details Aspect Ratio There are several options to set the image s aspect ratio depending on your input signal source See Selecting the aspect ratio on page 28 for details Corrects any keystoning of the image See Correcting keystone on Keystone page 27 for details Displays the position adjustment page To move the projected image Position use the directional arrow keys The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum Adjusts the clock phase to reduce image distortion Phase H Size Adjusts the horizontal width of the image Zoom Magnifies or reduces the projected image See Magnifying and searching for details on page 27 for details 3D Settings See Using the 3D functions on page 37 for details Color Management See Col
38. D Sub type connector to the COMPUTER IN 1 or COMPUTER IN 2 socket on the projector The projector is only capable of playing mixed mono audio even if a stereo audio input is connected See Connecting audio on page 17 for details If the selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal cables have been connected correctly X VGA Component adapter ViewSonic P N 00008906 Connecting an S Video source device Examine your Video source device to determine if it has an unused S Video output socket available you can continue with this procedure If not you will need to reassess which method you can use to connect to the device To connect the projector to an S Video source device 1 Take an S Video cable and connect one end to the S Video output socket of the Video source device 2 Connect the other end of the S Video cable to the S VIDEO socket on the projector The projector is only capable of playing mixed mono audio even if a stereo audio input is connected See Connecting audio on page 17 for details Ifthe selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal c
39. Digital keystone correction to correct distorted images Adjustable color management control for data video display Ability to display 1 07 billion colors Multi language On Screen Display OSD menus Switchable normal and economic modes to reduce the power consumption Component HDTV compatibility YPbPr HDMI CEC Consumer Electronics Control function allows synchronized power ON OFF operation between the projector and a CEC compatible device connected to the HDMI input of the projector C7 The apparent brightness of the projected image will vary depending on the ambient lighting conditions selected input signal contrast brightness settings and is directly proportional to projection distance lamp brightness will decline over time and may vary within the lamp manufacturers specifications This is normal and expected behavior Shipping contents Carefully unpack and verify that you have all of the items shown below If any of these items are missing please contact your place of purchase Standard accessories CT The supplied accessories will be suitable for your region and may differ from those illustrated VGA Cable lo el eec d de 5 Quick Start Guide Remote Control amp Batteries Multi language user manual DVD Optional accessories l Replacement lamp 2 carry case 3 VGA Component adapter Projector exterior view 1 External control pa
40. Electroser Av Reforma No 403Gx39 y 41 97000 Other places please refer to http www viewsonic 19 16 Latin America Peru www viewsonic com la T 0800 54565 soporte viewsonic com Macau www hk viewsonic com T 853 2870 0303 service hk viewsonic com Middle East ap viewsonic com me Contact your reseller service ap viewsonic com Puerto Rico amp Virgin Islands www viewsonic com T 1 800 688 6688 English T 1 866 379 1304 Spanish F 1 909 468 3757 service us viewsonic com soporte viewsonic com Si Malaysia 2 www viewsonic com sg T 65 6461 6044 service sg viewsonic com South Africa ap viewsonic com za Contact your reseller service ap viewsonic com United States www viewsonic com T Toll Free 1 800 688 6688 T Toll 1 424 233 2530 F 1 909 468 3757 service us viewsonic com Limited Warranty ViewSonic Projector What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components Limited Three 3 year General Warranty Subject to the more limited one 1 year warranty
41. SB port of the computer and smaller end to the MINI USB socket on the projector See Using the remote mouse control on page 10 for details Many notebooks do not turn on their external video ports when connected to a projector Usually a key combo like FN F3 or CRT LCD key turns the external display on off Locate a function key labeled CRT LCD or a function key with a monitor symbol on the notebook Press FN and the labeled function key simultaneously Refer to your notebook s documentation to find your notebook s key combination Connecting a monitor If you want to view your presentation close up on a monitor as well as on the screen you can connect the MONITOR OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below To connect the projector to a monitor 1 Connect the projector to a computer as described in Connecting a computer on page 16 2 Take a suitable VGA cable only one supplied and connect one end of the cable to the D Sub input socket of the video monitor Or if your monitor is equipped with a DVI input socket take a VGA to DVI A cable and connect the DVI end of the cable to the DVI input socket of the video monitor 3 Connect the other end of the cable to the MONITOR OUT socket on the projector C3 The MONITOR OUT output only works when COMPUTER IN 1 connection is made to the projector To use this connection method when the projector is in st
42. TURE gt Color menu and press lt gt Lower setting produces less saturated colors If the setting is too high colors on the image will be overpowering which makes the image unrealistic Adjusting Tint Highlight the PICTURE gt Tint menu and press lt gt The higher the value the more reddish the picture becomes The lower the value the more greenish the picture becomes Adjusting Sharpness Highlight the PICTURE gt Sharpness menu and press lt gt The higher the value the sharper the picture becomes The lower the value the softer the picture becomes Adjusting Brilliant Color Highlight the PICTURE gt Brilliant Color menu and press lt gt This feature utilizes a new color processing algorithm and system level enhancements to enable higher brightness while providing truer more vibrant colors in the projected picture It enables a greater than 50 brightness increase in mid tone images which are common in video and natural scenes so the projector reproduces images in realistic and true colors If you prefer images with that quality select On If you don t need it select Off When Off is selected the Color Temperature function is not available Selecting a Color Temperature Highlight the PICTURE gt Color Temperature menu and press lt gt The options available for color temperature settings vary according to the signal type selected 1 With the highest color temperature T1 makes the image a
43. ables have been connected correctly Ifyou have already made a Component Video connection between the projector and this S Video source device using Component Video connections you need not connect to this device using an S Video connection as this makes an unnecessary second connection of poorer picture quality See Connecting Video source devices on page 17 for details Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available you can continue with this procedure If not you will need to reassess which method you can use to connect to the device To connect the projector to a composite Video source device 1 Take a Video cable and connect one end to the composite Video output socket of the Video source device 2 Connect the other end of the Video cable to the VIDEO socket on the projector G The projector is only capable of playing mixed mono audio even if a stereo audio input is connected See Connecting audio on page 17 for details Ifthe selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the Video source device is turned on and operating correctly Also check that the signal cables have been connected correctly You need only connect to this device using a composite Video connection if Component Video and S Video inputs are u
44. ales SA de CV Calle Juarez 284 local 2 Col Bugambilias C P 83140 Tel 01 66 22 14 9005 E Mail disc2 hmo megared net mx Puebla Pue Matriz RENTA Y DATOS S A DE C V Domicilio 29 SUR 721 COL LA PAZ 72160 PUEBLA PUE Tel 01 52 222 891 55 77 CON 10 LINEAS E Mail datos puebla megared net mx Chihuahua Soluciones Globales en Computaci n C Magisterio 3321 Col Magisterial Chihuahua Chih Tel 4136954 E Mail Cefeo soluglobales com Distrito Federal QPLUS S A de C V Av Coyoac n 931 Col Del Valle 03100 M xico D F Tel 01 52 55 50 00 27 35 E Mail gacosta qplus com mx Guerrero Acapulco GS Computaci n Grupo Sesicomp Progreso 6 A Colo Centro 39300 Acapulco Guerrero Tel 744 48 32627 MERIDA ELECTROSER Av Reforma No 403Gx39 y 41 M rida Yucat n M xico CP97000 Tel 52 999 925 1916 E Mail rrrb sureste com Tijuana STD Av Ferrocarril Sonora 3780 1 Col 20 de Noviembre Tijuana Mexico Villahermosa Compumantenimietnos Garantizados S A de C V AV GREGORIO MENDEZ 1504 COL FLORIDA C P 86040 Tel 01 993 3 52 00 47 3522074 3 52 20 09 E Mail compumantenimientos prodigy net mx Veracruz Ver CONEXION Y DESARROLLO S A DE Av Americas 419 ENTRE PINZ N Y ALVARADO Fracc Reforma C P 91919 Tel 01 22 91 00 31 67 E Mail gacosta qplus com mx Cuernavaca Compusupport de Cuernavaca SA de CV Francisco Leyva 178 Col Miguel Hidalgo
45. andby mode turn on the Active VGA Out function under the SYSTEM SETTING BASIC gt Standby Settings menu Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets HDMI Component Video S Video Video composite You need only connect the projector to a Video source device using just one of the above connecting methods however each provides a different level of video quality The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below Best video quality The best available video connection method is HDMI If your source device is equipped with a HDMI socket you can enjoy uncompressed digital video quality See Connecting an HDMI device on page 18 for how to connect the projector to a HDMI source device and other details If no HDMI source is available the next best video signal is Component video not to be confused with composite video Digital TV tuner and DVD players output Component video natively so if available on your devices this should be your connection method of choice in preference to composite video See Connecting a Component Video source device on page 18 for how to connect the projector to a component video device Better video quality The S Video method provides a better quality analog video than stand
46. ard composite Video If you have both composite Video and S Video output terminals on your Video source device you should elect to use the S Video option See Connecting an S Video source device on page 19 for how to connect the projector to an S Video device Least video quality Composite Video is an analog video and will result in a perfectly acceptable but less than optimal result from your projector being the least video quality of the available methods described here See Connecting a composite Video source device on page 19 for how to connect the projector to a composite Video device Connecting audio The projector has one built in mono speaker which is designed to provide basic audio functionality accompanying data presentations for business purposes only It is not designed for nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications Any stereo audio input if provided is mixed into a common mono audio output through the projector speaker If you wish you can make use of the projector mixed mono speaker in your presentations and also connect separate amplified speakers to the Audio Out socket of the projector The audio output is a mixed mono signal and controlled by the projector Volume and Mute settings If you have a separate sound system you will most likely want to connect the audio output of your Video source device to that sound system instead of to the
47. assword is set the OSD menu returns to the Security Settings page 5 leave the OSD menu press MENU EXIT on the projector or Exit on the remote control Once a password has been set the projector cannot be used unless the correct password is entered every time the projector is started digits being input will be displayed as asterisks on screen Write your selected password down here in this user manual in advance or right after the password is entered so that it is available to you should you ever forget it Password Keep this user manual in a safe place If you forget the password If the password function is activated you will be asked to enter the six digit password every time you turn on the projector If you enter the wrong password the password error message as pictured to the right is Kien toa displayed lasting for three seconds and the message INPUT PASSWORD follows You can retry by entering another six digit password or if you did not record the password in this user manual and you absolutely do not remember it you can use the password recall procedure See Entering the password recall procedure on page 23 for details Password Error If you enter an incorrect password 5 times in succession the projector will automatically shut down in a short time Entering the password recall procedure 1 Open the OSD menu and go to the SYSTEM SETTING ADVANCED gt Security Settings gt
48. aturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71 Writ Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 rite Gain Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72 Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Writ Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 rite Freeze Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 Ox5F Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60 EA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0 60 0x06 0 14 0x00 0 04 0 00 0x34 0x13 0 01 0 08 0 68 Write nput source 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 Source input Composite nput source SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66 0x06 0 14 0x00 0 04 0 00 0x34 0x13 0 01 0x03 0x63 Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61 Quick Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62 I Search on I Write Quick Auto Quick Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61 Search Search off Read Quick Auto 0 27 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62 Search status RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 Write YUV 0x06 0x14 0x00 0 04 0x00 0x34 0x11 0x28 0 01 0 86 HDMI Format Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0
49. aves the settings made for the User 1 or User 2 mode 39YNoOS Function Description Quick Auto See Switching input signal on page 25 for details Search dis HDMI Format HDMI Range See Changing HDMI input settings on page 25 for details DynamicEco Timer Allows the projector to decrease the power consumption automatically if no input signal is detected after a set period of time C It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes Smart Restart Selecting On enables you to restart the projector immediately within 150 seconds after turning it off After 150 seconds if the projector is not turned on again it will directly enter the standby mode E It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes If the projector is resumed by using the Smart Restart feature this function can be executed immediately When On is selected the Quick Power Off function will be automatically set to On Pattern The projector can display several test patterns It helps you adjust the image size and focus and check that the projected image is free from distortion My Button Sets a hotkey on remote control keys on page 36 for details Splash Screen Allows you to select which logo screen will be displayed
50. ay from the projector Stand within 8 meters 26 feet of the projector Specifications Projector specifications HF Allspecifications are subject to change without notice Not all models be purchased in your region General Product name DLP Projector Optical Resolution PJD6235 PJD6245 1024 x 768 XGA PJD6543w 1280 x 800 WXGA Display system 1 DMD Lamp 190 W lamp Electrical Power supply AC100 240V 50 60 Hz Automatic Power consumption 250 W Max 0 5W Standby Mechanical Weight 2 1 Kg 4 63 Ibs Input terminal Computer input RGB input D Sub 15 pin female x 2 Video signal input S VIDEO Mini DIN 4 pin port x 1 VIDEO RCA jack x 1 SD HDTV signal input Analog D Sub Component RCA jack x 3 through RGB input Digital HDMI V1 4a x 1 Audio signal input PC audio jack x 1 Output terminal RGB output D Sub 15 pin female x 1 Audio signal output PC audio jack x 1 Speaker 2 watt x 1 Control terminal RS 232 serial control 9 pin x LAN RJ45 x 1 USB serial control Type mini B IR receiver x Front Environmental Requirements Operating temperature 0 C 40 C at sea level Operating relative humidity 10 90 without condensation Operating altitude 0 1499 m at 5 C 35 C 1500 3000 m at 5 C 25 C with High Altitu
51. creen picture 5 POWER indicator light Lights up or flashes when the projector is under operation 5 POWER Toggles the projector between standby mode and on 6 SOURCE Displays the source selection bar 7 MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu exits and saves menu settings 11 12 Right Activates panel key lock When the On Screen Display OSD menu is activated the 3 4 and 8 keys are used as directional arrows to select the desired menu items and to make adjustments LAMP indicator light Indicates the status of the lamp Lights up or flashes when the lamp has developed a problem AUTO Automatically determines the best picture timings for the displayed image TEMPerature indicator light Lights up red if the projector s temperature becomes too high MODE ENTER Selects an available picture setup mode Enacts the selected On Screen Display OSD menu item Remote control To use the remote mouse control keys Page Up Page Down n and e see Using the remote mouse control on page 10 for details 1 bPOWER Toggles the projector between standby mode and on 2 Source selection keys VGA Video Selects an input source for display VGA Selects D Sub Comp 1 or D Sub Comp 2 source for display Video Selects Video HDMI Video S Video source for display 3 Source Displays the source selection bar 4 Keystone keys w m
52. ct fire water lightning or other acts of nature improper maintenance unauthorized product modification or failure to follow instructions supplied with the product b Operation outside of product specifications Operation of the product for other than the normal intended use or not under normal conditions d Repair or attempted repair by anyone not authorized by ViewSonic e Any damage of the product due to shipment f Removalor installation of the product 9 Causes external to the product such as electric power fluctuations or failure h Use of supplies or parts not meeting ViewSonic s specifications i Normal wear and tear j Any other cause which does not relate to a product defect 3 Removal installation and set up service charges How to get service 1 Forinformation about receiving service under warranty contact ViewSonic Customer Support please refer to Customer Support page You will need to provide your product s serial number 2 To obtain warranted service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Take or ship the product freight prepaid in the original container to an authorized ViewSonic Service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic Limitation of implied warranties There are no
53. de Mode on Dimensions 268 mm W x 84 4 mm H x 221 mm D Excluding extrusions um 524 268 CA T 7 SE 84 4 SS Ceiling mount installation Ceiling mount screws 110 05 MA x 8 Max L 8 mm 55 81 5 Unit mm Timing chart Supported timing for PC input Vertical Horizontal Pixel Resolution Mode Frequency Frequency Frequency Hz kHz MHz 720 x 400 720x400 70 70 087 31 469 28 3221 VGA 60 59 940 31 469 25 175 VGA 72 72 809 37 861 31 500 64030480 VGA 75 75 000 37 500 31 500 VGA 85 85 008 43 269 36 000 SVGA 60 60 317 37 879 40 000 SVGA 72 72 188 48 077 50 000 800 x 600 SVGA 75 75 000 46 875 49 500 SVGA 85 85 061 53 674 56 250 SVGA 120 Reduce Blanking 119 854 77 425 83 000 XGA 60 60 004 48 363 65 000 XGA 70 70 069 56 476 75 000 1024 x 768 XGA 75 75 029 60 023 78 750 XGA 85 84 997 68 667 94 500 XGA 120 Reduce Blanking 119 989 97 551 115 500 1280x720 1280x720 120 120 90 000 148 500 WXGA 60 59 810 49 702 83 500 1280 x 800 WXGA 75 74 934 62 795 106 500 WXGA 85 84 880 71 554 122 500 SXGA 60 60 020 63 981 108 000 1280 x 1024 SXGA 75 75 025 79 976 135 000 SXGA 85 85 024 91 146 157 500 1280 x 960 1280 x 960 60 60 00
54. decide if you want to activate sound reminder by pressing lt gt If you select On a double beep sound will be heard at the last 30 seconds of counting down up and a triple beep sound will be produced when the timer is up 7 To activate the presentation timer press V and press lt gt to highlight Start Counting and press MODE ENTER 8 confirmation message displays Highlight Yes and press MODE ENTER on the projector or remote control to confirm You will see the message Timer is On displaying on the screen The timer starts counting when the timer is on To cancel the timer perform the following steps 1 Goto the SYSTEM SETTING ADVANCED gt Presentation Timer menu and highlight Off Press MODE ENTER A confirmation message displays 2 Highlight Yes and press MODE ENTER to confirm You will see the message Timer is Off displaying on the screen Hiding the image In order to draw the audience s full attention to the presenter you can use lt on the projector or Blank on the remote control to hide the screen image Press any key on the projector or remote control to restore the image The word BLANK appears at the lower right corner of the screen while the image is hidden You can set the blank time in the SYSTEM SETTING BASIC gt Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen C Once Blank is pressed the project
55. e My Button DCR Closed Caption Auto Off Auto Power Off Message Screen Color CEC Auto Search Quick Auto Search Information Language Multi language OSD selection Projector Position Front Table Rear Table Rear Ceiling Front Ceiling Disable 5 min 10 min 20 min 30 Auto Power Off min 40 min 50 min 60 min Blank Timer Disable 5 min 10 min 15 min 20 min 25 min 30 min Timer Off 30 min 1 hour 2 hours 3 Sleep Timer hours 4 hours 8 hours 12 hours 4 Panel Key Lock On Off SYSTEM Splash Screen Black Blue ViewSonic Off SETTING Message On Off BASIC DHCP On Off Projector IP Address LAN Control Subnet Mask Settings Default Gateway DNS Server Apply Power Saving On Off Active VGA Out On Off Standby Settings Active Audio Out On Off Quick Power Off On Off CEC On Off 5 SYSTEM SETTING ADVANCED High Altitude Mode DCR Audio Settings Menu Settings Closed Caption Lamp Settings Presentation Timer Security Settings Remote Control Code Reset Settings Mute Volume Menu Display Time Menu Position On Off On Off On Off 5 sec 10 sec 15 sec 20 sec 25 sec 30 sec Center Top Left Top Right Bottom Left Bottom Right Closed Caption Enable On Off Caption Version Lamp Mode Reset Lamp Timer Equivalent Lamp Hour Timer Period Timer Display Timer Position Timer Counting Direction Sound Reminder Start Counting Off Change Password Power On Lock Reset All Settings Reset Color Settings CC1 C
56. ells included with this equipment display the chemical symbol Hg Cd or Pb then it means that the battery has a heavy metal content of more than 0 000596 Mercury or more than 0 002 Cadmium or more than 0 004 Lead Important Safety Instructions so Ord e owe 10 11 12 13 14 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this unit near water Clean with a soft dry cloth Do not block any ventilation openings Install the unit in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade and the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs Convenience receptacles and the point where they exit from the unit Be sure that the power outlet is located near the unit so that it is easily accessible Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified
57. er outlet as well as the location and distance between the projector and the rest of your equipment Your projector is designed to be installed in one of four possible installation locations 1 Front Table Select this location with the projector placed near the floor in front of the screen This is the most common way to position the projector for quick setup and portability 2 Front Ceiling Select this location with the projector suspended upside down from the ceiling in front of the screen Purchase the projector ceiling mount kit from your dealer to mount your projector on the ceiling Set Front Ceiling in the SYSTEM SETTING BASIC gt Projector Position menu after you turn the projector on 3 Rear Ceiling Select this location with the projector suspended upside down from the ceiling behind the screen Note that a special rear projection screen and the projector ceiling mounting kit are required for this ES installation location N Set Rear Ceiling in the SYSTEM SETTING BASIC gt Projector Position menu after you turn the projector on 4 Rear Table Select this location with the projector placed near the floor behind the screen Note that a special rear projection screen is d required 4 Set Rear Table in the SYSTEM SETTING ae BASIC gt Projector Position menu after you turn the projector on Projection dimensions Refer to Dimensi
58. ess lt gt to select its range Increase in the range will include colors consisted of more proportions of its two adjacent colors Please refer to the illustration to the right for how the colors relate to each other For example if you select Red and set its range at 0 only pure red in the projected picture will be selected Increasing its range will include red close to yellow and red close to magenta 5 Press V to highlight Saturation and adjust its values to your preference by pressing lt gt Every adjustment made will reflect to the image immediately For example if you select Red and set its value at 0 only the saturation of pure red will be affected CF Saturation is the amount of that color in a video picture Lower settings produce less saturated colors a setting of 0 removes that color from the image entirely If the saturation is too high that color will be overpowering and unrealistic 6 Press V to highlight Gain and adjust its values to your preference by pressing lt The contrast level of the primary color you select will be affected Every adjustment made will reflect to the image immediately 7 steps 3 to 6 for other color adjustments Make sure you have made all of the desired adjustments 9 Press MENU EXIT on the projector or Exit on the remote control to exit and save the settings oo Setting the presentation timer Presentation timer can indicate the presen
59. est picture timings for the displayed image Remote control code 22 Color Mode Selects an available picture setup mode Exit Goes back to previous OSD menu exits and saves menu settings PgUp Page Up PgDn Page Down Operates your display software program on a connected PC which responds to page up down commands like Microsoft PowerPoint when the mouse mode is activated Volume keys Magnifies or reduces the volume level Toggles the projector audio between on and off Aspect Selects the display aspect ratio Timer Displays the presentation timer settings menu The projector can be assigned to two different remote control codes A or B When several adjacent projectors are in operation at the same time switching the remote control codes can prevent interference from other remote controls Set the remote control code for the projector first before changing that for the remote control To switch the code for the projector select A or B in the SYSTEM SETTING ADVANCED gt Remote Control Code menu To switch the code for the remote control press PgUp and PgDn buttons on the remote control together for 5 seconds or more The initial code is set to A C3 If different codes are set on the projector and remote control there will be no response from the remote control When that happens switch the code for the remote control again Using the remote mouse control The capability of operating
60. ff 3 Contact your ITS administrator for information on the Projector IP Address Subnet Mask Default Gateway and DNS Server settings 4 Press to select the item you want to modify and press MODE ENTER on the projector or Enter on the remote control 5 Press lt gt to move the cursor and the press V to enter the value 6 save the settings press MODE ENTER on the projector or Enter on the remote control If you do not want to save the settings press MENU EXIT on the projector or Menu on the remote control 7 Press v to highlight Apply and press MODE ENTER on the projector or Enter on the remote control C If the RJ45 cables are not properly connected the Projector IP Address Subnet Mask Default Gateway and DNS Server settings will display 0 0 0 0 Make sure the cables are properly connected and perform the procedures above again Ifyou wish to connect to the projector its standby mode be sure you have selected RJ45 and obtained the Projector IP Address Subnet Mask Default Gateway and DNS Server information when the projector is on Controlling the projector through a web browser Once you have the correct IP address for the projector and the projector is on or in standby mode you can use any computer that is on the same local area network to control the projector Ifyou are using Microsoft Internet Explorer make sure it is version 7 0 or higher screen shots in this manual are
61. free flow of air around the projector Locations where temperatures may become excessively high such as the inside of a car with all windows rolled up Locations where excessive humidity dust or cigarette smoke may contaminate optical components shortening the projector s life span and darkening the picture Locations near fire alarms Locations with an ambient temperature above 40 C 104 F Locations where the altitudes are higher than 3000 m 10000 feet 13 Do not block the ventilation holes If the ventilation holes are seriously obstructed overheating inside the projector may result in a fire Do not place this projector on a blanket bedding or any other soft surface Do not cover this projector with a cloth or any other item Do not place inflammables near the projector 14 Always place the projector on a level horizontal surface during operation Do not use if tilted at an angle of more than 10 degrees left to right nor at angle of more than 15 degrees front to back Using the projector when it is not fully horizontal may cause a malfunction of or damage to the lamp 15 Do not stand the projector on end vertically Doing so may cause the projector to fall over causing injury or resulting in damage to the projector 16 Do not step on the projector or place any objects upon it Besides probable physical damage to the projector doing so may result in accidents and possible injury 17 Do not place liquids near
62. frozen on the screen the pictures are running on the video or other device If the connected devices have active audio output you will still hear the audio even though the image is frozen on screen Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is between 1500 m 3000 m above sea level and temperature is between 0 C 35 C Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 0 C and 35 The projector will be over cooled if you turn the mode on under such a condition To activate the High Altitude Mode 1 Press MENU EXIT on the projector or Menu on Notice We recommend you use the High Altitude the remote control and then press lt gt until the EROR CRETE RR SYSTEM SETTING ADVANCED menu is highlighted Youwant to turn High Altitude 2 Press x to highlight High Altitude Mode and NS press lt gt to select On A confirmation message is displayed 3 Highlight Yes and press MODE ENTER on the projector or Enter on the remote control Operation under High Altitude Mode may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance If you use this projector under other extreme conditions excluding the above it may display auto shut down symptoms which is designed to protect your projector from
63. gt to navigate the picture 4 To reduce size of the picture press MODE ENTER on the projector or Enter on the remote control to switch back to the zoom in out functionality and press AUTO Auto Sync to restore the picture to its original size You can also press V repeatedly until it is restored to the original size Using the OSD menu 1 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the DISPLAY menu is highlighted 2 Press V to highlight Zoom and press MODE ENTER on the projector or Enter on the remote control The Zoom bar is displayed 3 Repeat steps 2 4 in the section of Using the remote control above HF The picture can only be navigated after the picture is magnified You can further magnify the picture while searching for details Images can only be magnified up to 120 when the aspect ratio is Wide or Anamorphic Selecting the aspect ratio The aspect ratio is the ratio of the image width to the image height Most analog TV and computers are in 4 3 ratio and digital TV and DVDs are usually in 16 9 ratio With the advent of digital signal processing digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal To change the projected image ratio no matter what aspect the source is Using the remote control l Press Aspect to show the current setting 2 Press
64. he remote control batteries 1 To open the battery cover turn the remote control over to view its back push on the finger grip on the cover and slide it in the direction of the arrow as illustrated The cover will slide off Remove any existing batteries if necessary and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment Positive goes to positive and negative goes to negative Refit the cover by aligning it with the base and sliding it back down into position Stop when it clicks into place Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen bathroom sauna sunroom or in a closed car Replace only with the same or equivalent type recommended by the battery manufacturer Dispose of the used batteries according to the manufacturer s instructions and local environment regulations for your region Never throw the batteries into a fire There may be danger of an explosion If the batteries are dead or if you will not be using the remote control for an extended period of time remove the batteries to avoid damage to the remote control from possible battery leakage Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select Take into consideration the size and position of your screen the location of a suitable pow
65. in the PICTURE menu Resolution Shows the native resolution of the input signal Color System Shows input system format NTSC PAL SECAM or RGB Equivalent Lamp Hour Displays the number of hours the lamp has been used MAC Address Shows the MAC Address of your projector c MAC Address stands for Media Access Control Address which is a physical layer address used to uniquely identify a network node Maintenance Care of the projector Your projector needs little maintenance The only thing you need to do on a regular basis is to keep the lens clean Never remove any parts of the projector except the lamp Contact your dealer if other parts need replacing Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface Useacanister of compressed air to remove dust is dirt or smears use lens cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface N CAUTION Never rub the lens with abrasive materials Cleaning the projector case Before you clean the case turn the projector offusing the proper shutdown procedure as described in Shutting down the projector on page 46 and unplug the power cord remove dirt or dust wipe the case with a soft lint free cloth To remove stubborn dirt or stains moisten a soft cloth with water and a neutral pH detergent Then wipe the case N CAUTION Never use wax alcohol benzene thinner or other
66. ions will be scaled by the projector depending upon the aspect ratio setting which may cause some image distortion or loss of picture clarity See Selecting the aspect ratio on page 28 for details Changing HDMI input settings In the unlikely event that you connect the projector to a device like a DVD or Blu ray player via the projector s HDMI input and the projected picture displays wrong colors please change the color space to an appropriate one that fits the color space setting of the output device To do this 1 Open the OSD menu and go to the SOURCE menu 2 Press V to highlight HDMI Format and press lt gt to select a suitable color space according to the color space setting of the output device connected RGB Sets the color space as RGB Sets the color space as YUV Auto Sets the projector to detect the color space setting of input signal automatically 3 Press v to highlight HDMI Range and press lt gt to select a suitable HDMI color range according to the color range setting of the output device connected Enhanced Sets the HDMI color range as 0 255 25 Normal Sets the HDMI color range as 15 235 C This function is only available when the HDMI input port is in use Refer to the documentation of the device for information on the color space setting Adjusting the projected image Adjusting the projection angle The projector is equipped with an adjuster foot It
67. itude A mode for operation in high altitude areas See Operating in a high altitude environment on page 36 for details Mode Enables or disables the DCR Dynamic Contrast Ratio function Selecting On enables the function and the projector will automatically switch the lamp mode between normal and economic DCR modes according to the input image detected Cr This function is only available when a PC source is in use A After enabling DCR frequent lamp mode switching may shorten lamp life and noise level will vary during operation Audio Settings The sound adjustments made as below will have an effect on the projector speaker Be sure you have made a correct connection to the projector audio input output jacks See Connection on page 15 for more details Mute Mutes the sound received from AUDIO IN Volume Adjusts the sound level received from AUDIO IN Menu Settings Menu Display Time Sets the length of time the OSD will remain active after your last key press The range is from 5 to 30 seconds in 5 second increments Menu Position Sets the On Screen Display OSD menu position q3ONVAQY SNILL3S WALSAS S Closed Caption Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions Captions An on screen display of the dialogue narration and sound effects of TV programs and videos that are closed captioned usually marked as CC in TV li
68. le org Be careful of broken glass when replacing the lamp Please wear eye protection and gloves when performing overhead installation To reduce the risk of electrical shock always turn the projector off and disconnect the power cord before changing the lamp To reduce the risk of severe burns allow the projector to cool for at least 45 minutes before replacing the lamp To reduce the risk of injuries to fingers and damage to internal components use caution when removing lamp glass that has shattered into sharp pieces Before replacing the lamp clean the lamp compartment and dispose of cleaning materials Be careful of sharp edges in the lamp compartment Wash hands after lamp replacement Only ViewSonic certified lamps are tested with this projector Use of other lamps may cause electrical shock and fire 1 Turn the power off and disconnect the projector from the wall socket If the lamp is hot avoid burns by waiting for approximately 45 minutes until the lamp has cooled 2 Loosen the screws that secure the lamp cover on the both sides of the projector until the lamp cover loosens 3 Remove the lamp cover from the projector N WARNING Do not turn the power on with the lamp cover removed Do not insert your fingers between the lamp and the projector The sharp edges inside the projector may cause injuries Remove and dispose of the lamp protection film 4 Lo
69. n Please change to an input signal which is compatible with the projector s resolution or set the input signal to a lower setting See Timing chart on page 68 for details Using the menus The projector is equipped with On Screen Display OSD menus for making various adjustments and settings OSD screenshots below are for reference only and may differ from the actual design Below is the overview of the OSD menu Main menu icon Screen Color E Aspect Ratio Highlight i Beni Phase Sub menu Size st eee Go to the Color Management previous page Current input _ ViewSonic MENU or to exit signal To use the OSD menus please set them to your familiar language first 1 Press MENU EXIT on the projector or 3 Press v to highlight Menu on the remote control to turn the OSD menu on Language and press lt gt to Screen Color Aspect Ratio Keystone Projector Position Front Table Auto Power Off Disable Blank Timer Disable Panel Key Lock Splash Screen ViewSonic On Message LAN Control Settings Standby Settings CEC 2 Use lt gt to highlight the SYSTEM 4 Press MENU EXIT twice on SETTING BASIC menu the projector or Exit on the E E remote control to leave and LESE 2 save the settings Language English Projector Position Front Table The first press leads you back Auto Power Off Disable S Blank Time
70. navailable for use See Connecting Video source devices on page 17 for details Operation ee up the projector Plug the power cord into the projector and into a wall socket Turn on the wall socket switch where fitted 2 Press POWER on the projector or remote control to start the projector The POWER indicator light stays blue when the projector is on If necessary Rotate the focus ring to adjust the image clearness C Ifthe projector is still hot from previous activity it will run the cooling fan for approximately 60 seconds before energizing the lamp To maintain the lamp life once you turn the projector on wait at least 5 minutes before turning it off 3 Ifthe projector is activated for the first time select your OSD language following the on screen instructions 4 Switch all of the connected equipment on 5 The projector will start to search for input signals The current input signal being scanned appears in the upper left corner of the screen If the projector doesn t detect a valid signal the message No Signal will continue to be displayed until an input signal is found You can also press SOURCE on the projector or remote control to select your desired input signal See Switching input signal on page 25 for details If the frequency resolution of the input signal exceeds the projector s operating range you will see the message Out of Range displayed on a blank scree
71. nel See Projector on page 7 for details Lamp cover Vent heated air exhaust Front IR remote sensor Adjuster foot Focus and Zoom rings Projection lens RS 232 control port 9 45 LAN input port 10 Type B USB port 11 HDMI port 12 RGB PC Component video YPbPr YCbCr signal input socket 2 13 RGB PC Component video YPbPr YCbCr signal input socket 1 14 RGB signal output socket Front upper side E Rear lower side GocacocecononoeononcooGGOOGoGOGOOGOOGOOGOGOO q o lll AOS OOO coo 15 S Video input socket 16 Video input socket 17 Audio signal input socket Audio signal output socket 18 Kensington anti theft lock slot 19 AC power cord inlet A Warning THIS APPARATUS MUST BE EARTHED When installing the unit incorporate a readily accessible disconnect device in the fixed wiring or connect the power plug to an easily accessible socket outlet near the unit If a fault should occur during operation of the unit operate the disconnect device to switch the power supply off or disconnect the power plug Controls and functions Projector 1 Focusring Adjusts the focus of the projected image 2 Zoomring Adjusts the size of the image 3 Keystone Arrow keys Up v Down Manually corrects distorted images resulting from an angled projection 4 lt Left Blank Hides the s
72. nly be received via TCP port 4661 Please refer to the below RS232 command table for the commands RS232 command table Pin assignment for this two end gt Pin Description Pin Description de Es asas 3 TX 4 NC Transma dea 5 GND 6 NC Ring recon n 7 RTSZ 8 CTSZ 9 Interface RS 232 protocol Baud Rate 115200 bps default Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None lt RS232 RJ45 command table gt Write Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 Ox5D Power Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 Ox5E Read nem 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 Ox5E Reset Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 Ox5F 5 Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 Ox2A 0x00 0x87 Splash Screen 0x06 0x14 0x00 0x04 0x00 0x34 0x11 Ox0A 0x00 0x67 Black Sp rr 0x06 0x14 0 00 0 04 0 00 0x34 0 11 OxOA 0 01 0 68 Write 5 s Splash Screen plash Screen 06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x69 ViewSonic Sp an Sereen 0x06 0x14 0x00 0x04 0x00 0x34 0x11 OxOA 0x04 0x6B Read SP ee 0x07 0x14 0 00 0 05 0 00 0 34 0 00 0x00 0 11 OxOA 0 68 0x06 0x14 0 00 0 04 0x00 0x34 0x11 OxOB 0 00 0x68 i Write Quick Power Quick Power
73. o multiple devices at the same time However it can only display one full screen at a time Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals You can also manually select the desired signal by pressing one of the source selection keys on the remote control or cycle through the available input signals 1 Cc D Sub Comp 1 Press SOURCE on the projector or remote D Sub 2 control A source selection bar is displayed Press A xV until your desired signal is selected and press MODE ENTER on the projector or Enter on the remote control Once detected the selected source information will be displayed on the screen for seconds If there are multiple devices connected to the projector repeat steps 1 2 to search for another signal S Video The brightness level of the projected image will change accordingly when you switch between different input signals Data graphic PC presentations using mostly static images are generally brighter than Video using mostly moving images movies The input signal type effects the options available for the Color Mode See Selecting a picture mode on page 31 for details Please see Projector specifications on page 65 for the native display resolution of this projector For best display picture results you should select and use an input signal which outputs at this resolution Any other resolut
74. ode Picture modes for different types of signals The picture modes available for different types of signals are listed below PC input signals D Sub Comp 1 2 analog RGB 1 Brightest mode Maximizes the brightness of the projected image This mode is suitable for environments where extra high brightness is required such as using the projector in well lit rooms 2 PC mode Is designed for presentations under daylight environment to match PC and notebook coloring 3 ViewMatch mode Switches between high brightness performance and accurate color performance 4 Movie mode Is appropriate for playing colorful movies video clips from digital cameras or DVs through the PC input for best viewing in a blackened little light environment 5 Dynamic PC mode Is designed for presentations under daylight environment to match PC and notebook coloring In addition the projector will optimize the image quality using the dynamic PC function in accordance with the projected contents It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes If the projector is resumed by using the Smart Restart feature this function can be executed immediately 6 Dynamic Movie mode Is appropriate for playing colorful movies video clips from digital cameras or DVs through the PC input for best viewing in a blackened little light environment In addition the projector will optimize the image q
75. ons 2 Use the correct signal cables for each source 3 Ensure the cables are firmly inserted Inthe connections shown below some cables may not be included with the projector see Shipping contents on page 5 They are commercially available from electronics stores connection illustrations below are for reference only The rear connecting jacks available on the projector vary with each projector model For detailed connection methods see pages 16 19 Notebook or desktop computer Monitor VGA e mm o co RS 232 SLAN MINIUSB COMPUTER IN 2 1 VGA cable 5 S Video cable 2 VGA to DVI A cable 6 Video cable 3 USB cable 7 Audio cable 4 Component Video to VGA D Sub 8 HDMI cable adapter cable Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM compatibles and Macintosh computers Mac adapter is needed if you are connecting legacy version Macintosh computers To connect the projector to a notebook or desktop computer 1 the supplied VGA cable and connect one end to the D Sub output socket of the computer 2 Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector 3 Ifyou wish to use the remote paging function take a USB cable and connect the larger end to the U
76. ons on page 67 for the center of lens dimensions of this projector before calculating the appropriate position CT The screen mentioned below refers to the projection screen usually consisting of a surface and a support structure PJD6235 PJD6245 4 3 image on 4 3 screen e Screen f Center of lens 4 3 image on a 4 3 Screen 16 9 image on a 4 3 Screen Screen Size b Projection c Image d Vertical b Projection distance c Image d Vertical inch m distance m inch height offset m inch height offset min max inch cm inch min max inch cm inch 0 8 1 1 45 1 2 49 46 18 5 18 11 45 12 49 34 14 103 4 1 40 1 0 1 5 59 1 7 65 61 24 6 24 1 5 59 17 65 46 18 137 5 4 50 13 19 74 21 82 76 30 8 30 19 74 21 82 57 23 17 1 6 8 60 15 2 3 89 2 5 98 91 36 9 3 6 2 3 89 2 5 98 69 70 18 2 6 104 2 9 114 107 42 11 26 104 29 114 80 30 S eS wi O 27 20 6 8 1 2 24 0 9 5 36 27 4 10 8 1 30 9 12 2 45 80 20 3 0 119 3 3 131 122 48 12 3 0 119 3 3 131 91 90 2 3 3 4 134 3 7 147 137 54 14 100 2 5 3 8 149 4 2 163 152 60 15 45 34 3 13 5 120 3 0 4 5 178 5 0 196 183 72 18 4 5 178 5 0 196 137 54 41 1 16 2 150 3 8 5
77. or Management on page 34 for details Function Description Pre defined picture modes are provided so you can optimize your Color Mode projector image set up to suit your program type See Selecting a picture mode on page 31 for details Selects a picture mode that most suits your need for the image quality Reference and further fine tune the image based on the selections listed on the Mode same page below See Setting the User 1 User 2 mode on page 32 for details Brightness ades jx puc of the image See Adjusting Brightness on page or details M Contrast Adjusts the degree of difference between dark and light in the image See Adjusting Contrast on page 33 for details a Color Adjusts the color saturation level the amount of each color in a c video image See Adjusting Color on page 33 for details m Adjusts the red and green color tones of the image See Adjusting 3 Tint Tint on page 33 for details z The function is only available when Video or S Video with NTSC system is selected usts the image to make it look sharper or softer See ustin Sharpness Adj he imag ke it look sharp fter See Adjusting Sharpness on page 33 for details Brilliant Color Adjusts white peaking while maintaining correct color presentation See Adjusting Brilliant Color on page 33 for details Color Temperature See Selecting a Color Temperature on page 33 for details Save Settings S
78. or enters Economic mode automatically Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire Locking control keys With the control keys on the projector locked you can prevent your projector settings from being changed accidentally by children for example When the Panel Key Lock is on no control keys on the projector will operate except 5 POWER 1 Press gt on the projector or Lock on the remote control or go to the SYSTEM SETTING BASIC gt Panel Key Lock menu and select On by pressing lt gt on the projector or remote control 2 Aconfirmation message is displayed Select Yes to confirm To release panel key lock press and hold gt on the projector or Lock on the remote control for 3 seconds You can also use the remote control to enter the SYSTEM SETTING BASIC gt Panel Key Lock menu and press lt gt to select Off C7 Keys on the remote control are still functional when panel key lock is enabled Ifyou press POWER to turn off the projector without disabling panel key lock the projector will still be in locked status the next time it is turned on Freezing the image Press Freeze on the remote control to freeze the image The word FREEZE will be displayed in the upper left corner of the screen To release the function press any key on the projector or remote control Even if an image is
79. or on the projector Liquids spilled into the projector may cause it to fail If the projector does become wet disconnect it from the power supply s wall socket and call your local service center to have the projector serviced 18 This product is capable of displaying inverted pictures for ceiling mount installation Use only qualified ceiling mount kit for mounting the projector and ensure it is A securely installed 19 When the projector is under operation you may sense some heated air and odor from its ventilation grill It is a normal phenomenon and not a product defect 20 Do not use the Security bar for transporting or installation It should be used with a commercially available theft prevention cable Safety instructions for ceiling mounting of the projector We want you to have a pleasant experience using your projector so we need to bring this safety matter to your attention to prevent damage to person and property If you intend to mount your projector on the ceiling we strongly recommend that you use a proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed If you use an inappropriate projector ceiling mount kit there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws You can purchase a projector ceiling mount kit from the place you purchased your projector We recommends that you also pu
80. or users in Europe and Russia full details of warranty provided can be found in www viewsoniceurope com under Support Warranty Information Projector Warranty Term Template In UG VSC TEMP 2005 Mexico Limited Warranty ViewSonic Projector What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components amp accessories How long the warranty is effective 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification unauthorized attempted repair or failu
81. osen the screw that secures the lamp 5 Disconnect the lamp s wire connector from the projector and then lift the handle so that it stands up Use the handle to slowly pull the lamp out of the projector CAUTION Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector Do not place the lamp in locations where water might splash on it children can reach it or near flammable materials Do not insert your hands into the projector after the lamp is removed If you touch the optical components inside it could cause color unevenness and distortion of the projected images 6 Insert the new lamp into the lamp compartment and make sure it fits in the projector Connect the new lamp s wire connector to the projector 7 Tighten the screw that secures the lamp CAUTION Loose screw may cause a bad connection which could result in malfunction Do not over tighten the screw 8 Ensure the handle is fully laid flat and locked in place 9 Place the lamp protection film supplied with the new lamp on the lamp compartment 10 Replace the lamp cover on the projector 1l Tighten the screws that secure the lamp cover CAUTION Loose screw may cause a bad connection which could result in malfunction Do not over tighten the screws 12 Restart the projector CAUTION Do not turn the power on
82. out it is recommended that you connect your projector through a power stabilizer surge protector or uninterruptible power supply UPS 6 Donot block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire To temporarily turn off the lamp press BLANK on the projector or remote control 7 The lamp becomes extremely hot during operation Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement 8 Do not operate lamps beyond the rated lamp life Excessive operation of lamps beyond the rated life could cause them to break on rare occasions 9 Never replace the lamp assembly or any electronic components unless the projector is unplugged 10 Do not place this product on an unstable cart stand or table The product may fall sustaining serious damage 11 Do not attempt to disassemble this projector There are dangerous high voltages inside which may cause death if you should come into contact with live parts The only user serviceable part is the lamp which has its own removable cover Under no circumstances should you ever undo or remove any other covers Refer servicing only to suitably qualified professional service personnel 12 Do not place this projector in any of the following environments Space that is poorly ventilated or confined Allow at least 50 cm clearance from walls and
83. over heating In cases like this you should switch to High Altitude Mode to solve these symptoms However this is not to state that this projector can operate under any and all harsh or extreme conditions Using the CEC function This projector supports CEC Consumer Electronics Control function for synchronized power on off operation via HDMI connection That is if a device that also supports CEC function is connected to the HDMI input of the projector when the projector s power is turned off the power of the connected device will also be turned off automatically When the power of the connected device is turned on the projector s power will be turned on automatically To turn on the CEC function 1 Press MENU EXIT on the projector or Menu on the remote control to open the On Screen Display OSD menu 2 Goto the SYSTEM SETTING BASIC gt menu 3 Press lt gt to select On In order for the CEC function to work properly make sure that the device is correctly connected to the HDMI input of the projector via a HDMI cable and its CEC function is turned on Depending on the connected device the CEC function may not work Using the 3D functions This projector features 3D function which enables you to enjoy 3D movies videos and sporting events in a more realistic way by presenting the depth of the images You need to wear a pair of 3D glasses to view 3D images If the 3D signal is input from an HDMI 1
84. particular purpose Further ViewSonic Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes DLP and Digital Micromirror Device DMD are trademarks of Texas Instruments Others are copyrights of their respective companies or organizations Appendix IR control table Code A Power NEC 83 F4 17 E8 Auto Sync NEC 83 F4 08 F7 VGA NEC 83 F4 41 BE Video NEC 83 F4 52 AD Source NEC 83 F4 04 FB Color Mode NEC 83 F4 10 EF 5 83 F4 0B F4 Left NEC 83 F4 0E F1 Pover Enter NEC 83 F4 15 EA Right NEC 83 F4 OF FO Down KeyS NEC 83 F4 0C F3 Menu NEC 83 F4 30 CF My Button NEC 83 F4 56 A9 Exit NEC 83 F4 28 D7 Mouse L key NEC 83 F4 36 c9 Mouse R key NEC 83 F4 37 C8 PgUp NEC 83 F4 05 FA PgDn NEC 83 F4 06 F9 m zm Mouse NEC 83 F4 31 CE ooo Magnify NEC 83 F4 32 CD e e e Volume NEC 83 F4 82 7D eo Volume NEC 83 F4 83 7C Sl Panel Key Lock NEC 83 F4 57 A8 Freeze NEC 83 F4 03 FC Pattern NEC 83 F4 55 AA Blank NEC 83 F4 07 F8 Mute NEC 83 F4 14 EB DynamicEco NEC 83 F4 2B D4 Timer NEC 83 F4 27 D8 Aspect NEC 83 F4 13 EC Code B Key Format Bytei Byte2 Byte Bytes Power NEC 83 F4 60 9F Auto Sync NEC 83 F4 63 9C VGA NEC 83 F4
85. ppear the most bluish white than other settings 2 T2 Makes images appear bluish white 3 T3 Maintains normal colorings for white 4 T4 Makes images appear reddish white About color temperatures There are many different shades that are considered to be white for various purposes One of the common methods of representing white color is known as the color temperature white color with a low color temperature appears to be reddish white A white color with a high color temperature appears to have more blue in it Color Management Only in permanent installations with controlled lighting levels such as boardrooms lecture theaters or home theaters should color management be considered Color management provides fine color control adjustment to allow for more accurate color reproduction should you require it If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors TVs projectors etc you can project any image from the disc on the screen and enter the Color Management menu to make adjustments To adjust the settings 1 Goto the DISPLAY menu and highlight Color Management 2 Press MODE ENTER on the projector or Enter on the remote control and the Color Management page is displayed 3 Highlight Primary Color and press lt gt to select a color from among Red Yellow Green Cyan Blue or Magenta 4 Press V to highlight Hue and pr
86. r Disable to the main menu and the Panel Key Lock off Splash Screen ViewSonic second press closes the OSD Message On LAN Control Settings menu Standby Settings CEC H y DISPLAY SYSTEM SETTING BASIC PICTURE SYSTEM SETTING ADVANCED SOURCE INFORMATION Utilizing the password function For security purposes and to help prevent unauthorized use the projector includes an option for setting up password security The password can be set through the On Screen Display OSD menu For details of the OSD menu operation please refer to Using the menus on page 21 C3 You will be inconvenienced if you activate the password functionality and subsequently forget the password Print this user manual if necessary and write the password you used in this manual and keep it in a safe place for later use Setting a password 1 Open the OSD menu and go to the SYSTEM SETTING ADVANCED gt Security Settings menu Press MODE ENTER on the projector or Enter on the remote control The Security Settings page is displayed Highlight Power On Lock and select On by pressing lt gt 3 As pictured to the right the four arrow keys INPUT PASSWORD V 2 respectively represent 4 digits to set press the arrow keys to enter six digits for the password 4 Confirm the new password by re entering the new password 1 2 3 4 According to the password you desire Once the p
87. rchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the ceiling mount bracket This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose Introduction Projector features The projector integrates high performance optical engine projection and a user friendly design to deliver high reliability and ease of use The projector offers the following features Dynamic PC and Dynamic Movie functions adjusting the power consumption of the lamp according to the brightness of the image being projected DynamicEco Timer function decreasing the power consumption of the lamp by up to 30 when no input signal can be detected for a set period of time Presentation timer for better control of time during presentations LAN Settings allowing management of projector status from a remote computer Supports 3D display Color Management allowing color adjustments to your liking Less than 0 5W power consumption when power saving mode is turned on Screen Color correction allowing projection on surfaces of several predefined colors Quick auto search speeding up the signal detecting process Color and Reference modes providing choices for different projection purposes Selectable quick power off function auto adjustment to display the best picture quality
88. re to follow instructions supplied with the product Any damage of the product due to shipment Causes external to the product such as electrical power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect 3 Any product exhibiting a condition commonly known as image burn in which results when a static image is displayed on the product for an extended period of time 4 Removal installation insurance and set up service charges How to get service For information about receiving service under warranty contact ViewSonic Customer Support Please refer to the attached Customer Support page You will need to provide your product s serial number so please record the product information in the space provided below on your purchase for your future use Please retain your receipt of proof of purchase to support your warranty claim For Your Records mo a C Product Name Model Number Document Number Serial Number Purchase Date Extended Warranty Purchase Y N If so what date does warranty expire 1 To obtain warranty service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 2 Take ship the product in the original container packaging to an authorized ViewSonic se
89. rence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment For Canada e This Class B digital apparatus complies with Canadian ICES 003 e Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada CE Conformity for European Countries C The device complies with the EMC Directive 2004 108 EC and Low Voltage Directive 2006 95 EC Following information is only for EU member states The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste but use the return and collection systems available If the batteries accumulators and button c
90. ron com amp www crestron com getroomview Crestron RoomView On the Edit Room page enter the IP Address or hostname as shown on the projector s on screen display OSD menu and 02 for IPID 41794 for the reserved Crestron control port Gewa ous Roon Name Conference Room 1 Phone Location Corte Lek Brows Save Room About Crestron RoomView setting and command method please access below website to get RoomView User Guide and more information http www crestron com products roomview_connected_embedded_projectors_devices resources asp PJLink SNMP AMX and Xpanel formats supported This projector is PJLink SNMP V 1 AMX or Xpanel V1 10 compliant For details please follow its user guide or website respectively to control and manage projectors Using the projector in standby mode Some of the projector functions are available in standby mode plugged in but not turned on To use these functions be sure you have turned on the corresponding menus under SYSTEM SETTING BASIC gt Standby Settings and the cable connections are correctly made For the connection methods see the Connection chapter Power Saving Less than 0 5W power consumption when Power Saving mode is turned on When Power Saving is On the network function is not available when the projector is in standby mode Active VGA Out Selecting On outputs a VG
91. rted timing for HDMI input Horizontal Vertical Dot Clock Video Mode Resolution frequency Frequency Frequency KHz Hz MHz 480i 720 1440 x 480 15 73 59 94 27 480p 720 x 480 31 47 59 94 27 576i 720 1440 x 576 15 63 50 27 576p 720 x 576 31 25 50 27 720 50p 1280 x 720 37 5 50 74 25 720 60p 1280 x 720 45 00 60 74 25 1080 50i 1920 x 1080 28 13 50 74 25 1080 60i 1920 x 1080 33 75 60 74 25 1080 24P 1920 x 1080 27 24 74 25 1080 50P 1920 x 1080 56 25 50 148 5 1080 60P 1920 x 1080 67 5 60 148 5 Supported timing for 3D signal with Frame Sequential format Supported timing for 3D signal with Frame Packing and Top Bottom formats Supported timing for 3D signal with Frame Sequential Frame Packing and Top Bottom formats Supported timing for 3D signal with Side by Side format Supported timing for 3D signal with Frame Sequential and Top Bottom formats Vertical Horizontal Pixel Resolution Mode Frequency Frequency Frequency Hz kHz MHz 720 x 400 720x400 70 70 087 31 469 28 3221 VGA 60 59 940 31 469 25 175 VGA 72 72 809 37 861 31 500 640480 VGA 75 75 000 37 500 31 500 VGA 85 85 008 43 269 36 000 SVGA 60 60 317 37 879 40 000 SVGA 72 72 188 48 077 50 000 800 x 600 SVGA 75 75 000 46 875 49 500 SVGA 85 85 061 53 674 56 250 SVGA 120 Reduce Blanking 119 854 77 425 83 000
92. rvice center 3 Round trip transportation costs for in warranty products will be paid by ViewSonic Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damages based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercial loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise Any claim against the customer by any other party 4 Repair or attempted repair by anyone not authorized by ViewSonic e 83 Contact Information for Sales amp Authorized Service Centro Autorizado de Servicio within Mexico Name address of manufacturer and importers M xico Av de la Palma 8 Piso 2 Despacho 203 Corporativo Interpalmas Col San Fernando Huixquilucan Estado de M xico Tel 55 3605 1099 http www viewsonic com la soporte index htm N MERO GRATIS DE ASISTENCIA T CNICA PARA TODO M XICO 001 866 823 2004 Hermosillo Distribuciones y Servicios Computacion
93. set out below North and South America Three 3 years warranty for all parts excluding the lamp three 3 years for labor and one 1 year for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Limited One 1 year Heavy Usage Warranty Under heavy usage settings where a projector s use includes more than fourteen 14 hours average daily usage North and South America One 1 year warranty for all parts excluding the lamp one 1 year for labor and ninety 90 days for the original lamp from the date of the first consumer purchase Europe One 1 year warranty for all parts excluding the lamp one 1 year for labor and ninety 90 days for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration failure or malfunction resulting from a Accident abuse misuse negle
94. ssible color difference between the source and projected pictures To use this function go to the DISPLAY gt Screen Color menu and press lt gt to selecta color which is closest to the color of the projection surface There are several precalibrated colors to choose from Whiteboard Greenboard and Blackboard C3 This function is only available when a PC type input signal is selected Fine tuning the image quality in user modes According to the detected signal type there are some user definable functions available when User 1 or User 2 mode is selected You can make adjustments to these functions based on your needs When you are done making adjustments remember to go to the PICTURE gt Save Settings menu and press MODE ENTER to save your settings 32 Adjusting Brightness Highlight the PICTURE gt Brightness menu and press lt gt The higher the value the brighter the image And the lower the setting the darker the image Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible Adjusting Contrast Highlight the PICTURE gt Contrast menu and press lt gt The higher the value the greater the contrast Use this T Lm to set the peak white level after you have previously a m mA adjusted the Brightness setting to suit your selected input and viewing environment ao 0 20 Adjusting Color Highlight the PIC
95. stings Cr This function is only available when a Composite video or S Video input signal is selected and its system format is NTSC Caption Version Selects a preferred closed captioning mode To view captions select 2 or displays captions in the primary language in your area Lamp Settings Lamp Mode See Setting Lamp Mode as Economic on page 58 for details Reset Lamp Timer See Resetting the lamp timer on page 62 for details Equivalent Lamp Hour See Getting to know the lamp hour on page 58 for details on how the total lamp hour is calculated qq3ONVAQY SNILL3S WALSAS S Function Description Presentation Reminds the presenter to finish the presentation within a certain time Timer frame See Setting the presentation timer on page 35 for details Securit Settings See Utilizing the password function on page 22 for details Remote Control Code See Remote control code on page 9 for details Reset Settings Reset All Settings Returns all settings to the factory preset values Cr The following settings will still remain Keystone Language Projector Position High Altitude Mode Security Settings Remote Control Code Reset Color Settings Returns all color settings to the factory preset values NOLLVINSHOHNI 79 Current System Status Source Shows the current signal source Color Mode Shows the selected mode
96. tation time on the screen to help you achieve better time management when giving presentations Follow these steps to utilize this function 1 Press Timer on the remote control to access the Presentation Timer menu or go to the SYSTEM SETTING ADVANCED gt Presentation Timer menu and press MODE ENTER to display the Presentation Timer page 2 Highlight Timer Period and decide the time period by pressing lt gt The length of time can be set from 1 to 5 minutes in 1 minute increments and 5 to 240 minutes in 5 minute increments If the timer is already on the timer will restart whenever the Timer Period is reset 3 Press W to highlight Timer Display and choose if you want the timer to show up on the screen by pressing lt gt Selection Description Always Displays the timer on screen throughout the presentation time 1 min 2 min 3 min Displays the timer on screen in the last 1 2 3 minute s Never Hides the timer throughout the presentation time 4 Press V to highlight Timer Position and set the timer position by pressing lt gt Top Left gt Bottom Left gt Top Right gt Bottom Right 5 Press V to highlight Timer Counting Direction and select your desired counting direction by pressing lt gt Selection Description Count Up Increases from 0 to the preset time Count Down Decreases from the preset time to 0 6 Press v to highlight Sound Reminder and
97. ter of the screen with a 16 10 aspect ratio This is most suitable for images which are already in a 16 10 aspect as it displays them without aspect alteration Wide PJD6543w only Scales a 4 3 aspect image vertically and horizontally in a non linear manner so that it fills the screen with a 16 9 aspect ratio O O O Qu O O O 16 10 picture O O U w O O O 15 9 picture 9 O e 4 3 picture O O O O 9 9 O O O O 16 9 picture 2 2 O O O 16 10 picture gt O O 4 3 picture O O O Anamorphic PJD6235 PJD6245 only Scales a 16 9 aspect image vertically and horizontally in a non linear manner so that it fills the screen with a 4 3 aspect ratio m O O 16 9 picture Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type To select an operation mode that suits your need you can follow one of the following steps Press MODE ENTER on the projector or Color Mode on the remote control repeatedly until your desired mode is selected Goto the PICTURE gt Color Mode menu and press lt gt to select a desired m
98. the same as the ones on OSD menus or remote control See 2 PICTURE menu on page 52 and Projector on page 7 for details ii To switch between input signals click on your desired signal ET The Menu button can also be used to go back to previous OSD menus exit and save menu settings source list varies according to the connectors available on the projector When you use the projector control panel or remote control to change the OSD menu settings it may take a while for the web browser to synchronize these changes with the projector 2 tools page allows you to manage the projector configure the LAN control settings and secure access of remote network operation on this projector Contact IT Crestron Control O Projector User Password p Addr P L Enabled Port Ip Address 1 Admin Password Y SubnetMask 2 Default Gateway DNS Serer 1052 LJEnabled i This section is only used with the Crestron Control System Please contact Creston or refer to its user manual for setup information ii You can name the projector keep track of its location and the person in charge of it iii You can adjust the LAN Control Settings iv Once set access to the remote network operation on this projector has been password protected v Once set access to the tools page has been password protected CF To prevent errors only input the English alphabet and digits on the tools page
99. to the situation where the projected image is noticeably wider at either the top or bottom It occurs when the projector is not perpendicular to the screen To correct this besides adjusting the height of the projector you will need to manually correct it following one of these steps Using the remote control Press w m on the projector or remote control to display the Keystone correction page Press w to correct keystoning at the top of the image Press to correct keystoning at the bottom of the image Press m V Press W A Using the OSD menu 1 Press MENU EXIT on the projector or Menu on the remote control and then press lt gt until the DISPLAY menu is highlighted 2 Press v to highlight Keystone and press MODE ENTER on the projector or Enter on the remote control The Keystone correction page is displayed 3 Press to correct keystoning at the top of the image or press wr to correct keystoning at the bottom of the image Magnifying and searching for details If you need to find the details on the projected picture magnify the picture Use the direction arrow keys for navigating the picture Using the remote control 1 Press Magnify on the remote control to display the Zoom bar 2 Press A repeatedly to magnify the picture to a desired size 3 To navigate the picture press MODE ENTER on the projector or Enter on the remote control to switch to the paning mode and press the directional arrows KAM
100. tronic ceramic parts e g piezoelectronic devices 2 Leadin high temperature type solders i e lead based alloys containing 8596 by weight or more lead 3 Lead as an allotting element in steel containing up to 0 35 lead by weight aluminium containing up to 0 496 lead by weight and as a cooper alloy containing up to 4 lead by weight Copyright Information Copyright O ViewSonic Corporation 2012 All rights reserved Macintosh and Power Macintosh are registered trademarks of Apple Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three birds logo OnView ViewMatch and ViewMeter are registered trademarks of ViewSonic Corporation VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA PS 2 VGA and XGA are registered trademarks of International Business Machines Corporation Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omis sions contained herein nor for incidental or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied
101. uality using the dynamic Movie function in accordance with the projected contents It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes If the projector is resumed by using the Smart Restart feature this function can be executed immediately 7 User 1 User 2 mode Recalls the settings customized based on the current available picture modes See Setting the User 1 User 2 mode on page 32 for details Video input signals S Video Video D Sub Comp 1 2 YPbPr HDMI 1 Brightest mode Optimized for daylight viewing with living room level ambient brightness 2 Gaming mode Suitable for all types of entertainment media including gaming and movies 3 ViewMatch mode Switches between high brightness performance and accurate color performance 4 Movie mode Is suitable for enjoying dark movies or DVD movies best viewed in a blackened little light home cinema or lounge room environment 5 Dynamic Movie mode Is suitable for enjoying dark movies or DVD movies best viewed in a blackened little light home cinema or lounge room environment In addition the projector will optimize the image quality using the dynamic Movie function in accordance with the projected contents It takes some time to initiate this function Make sure the projector has been turned on for more than 4 minutes If the projector is resumed by using the Smart Restart feature this f
102. unction can be executed immediately 6 User 1 User 2 mode Recalls the settings customized based on the current available picture modes See Setting the User 1 User 2 mode on page 32 for details Setting the User 1 User 2 mode There are two user definable modes if the current available picture modes are not suitable for your need You can use one of the picture modes except the User 1 User 2 as a starting point and customize the settings 1 Press MENU EXIT on the projector or Menu on the remote control to open the On Screen Display OSD menu 2 Go to the PICTURE gt Color Mode menu 3 Press lt gt to select User 1 or User 2 4 Press v to highlight Reference Mode This function is only available when User 1 or User 2 mode is selected up in the Color Mode sub menu item 5 Press lt gt to select a picture mode that is closest to your need 6 Press V to select a sub menu item to be changed and adjust the value with lt gt See Fine tuning the image quality in user modes below for details 7 When all settings have been done highlight Save Settings and press MODE ENTER on the projector or Enter on the remote control to store the settings 8 Theconfirmation message Setting Saved is displayed Using Screen Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white the Screen Color feature can help correct the projected picture s colors to prevent po
103. x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63 Horizontal position shift 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65 Write right Horizontal Horizontal position Pis 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64 position shift left Read ae 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65 Sm 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65 Vert Write ertical Vertical position 44 9x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66 position shift down Read 0x07 0x14 0 00 0 05 0 00 0x34 0x00 0x00 0 12 0 07 0x66 Color 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66 temperatureT 1 Color 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67 I temperatureT2 Write Coi Color Bed 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68 temperatureT3 temperature Corot 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69 temperatureT4 Color Read temperature 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67 status Writ Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68 rite Blank Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67 Read Blank status 0x07 0 14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 I Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Keystone Write Vertical Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Read Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
104. x87 Read 0x07 0x14 0 00 0 05 0 00 0x34 0 00 0 00 0 11 0 28 0 86 Writ Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 rite Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 HDMI Range Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87 Writ Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61 rite Mute Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60 Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61 0 06 0 14 0 00 0 04 0 00 0 34 0 14 0 01 0 00 0 61 Volume Write Volume 0 06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62 Volume Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64 ENGLISH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 FRANCAIS 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 DEUTSCH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 ITALIANO 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 ESPA OL 0 06 0x14 0 00 0 04 0 00 0x34 0x15 0 00 0 04 0x65 0 06 0 14 0 00 0 04 0 00 0 34 0 15 0 00 0 05 0 66 xB HZ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0 06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 AE 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 REN 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A Write id Svenska 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 Ox0a 0 6 Nederlands 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 OxOb Ox6C T rkce 0x06 0x
105. your computer with the remote control gives you more flexibility when delivering presentations 1 Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer s mouse See Connecting a computer on page 16 for details 2 Setthe input signal to D Sub Comp 1 D Sub Comp 2 3 Press Mouse on the remote control to switch from the normal mode to the mouse mode An icon appears on the screen to indicate the activation of the mouse mode 4 Perform the desired mouse controls on your remote control move the cursor on the screen press Q A N Toleft click press B To right click press operate your display software program on a connected PC which responds to page up down commands like Microsoft PowerPoint press PgUp PgDn To return to the normal mode press Mouse again or other keys except for the mouse related multi function keys Remote control effective range The Infra Red IR remote control is located on the front of the projector The remote control must be held at an angle within 30 degrees perpendicular to the projector s IR remote control sensor to function correctly The distance between the remote control and the sensor should not exceed 8 meters 26 feet Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra red beam Replacing t

PJD6235/PJD6245/PJD6543w DLP Projector

Contents

Download Pdf Manuals

Related Search

Related Contents