Home

Part #500830-001 Product Manual

1. Perform a complete inspection of the unit and document the results prior to storage 2 3 4 Oil or grease all of the clamping screw threads to prevent corrosion The DSR ADJ system can be dismantled for storage if desired follow the reverse of the steps given for assembly in section 3 0 of this manual 8 0 Contact Information For More Information PELSUE T A Pelsue Company 2500 S Tejon St Englewood CO 80110 Toll Free 1 800 525 8460 Telephone 1 303 936 7432 Fax 1 303 934 5581 Website www pelsue com Email sales pelsue com 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 1 9 Pelsue Company 2500 South Tejon Street Englewood Colorado USA 80110 ISO 9001 Certi T ied Toll free 800 525 8460 or 303 936 7432 Fax 303 934 5581 Internet www pelsue com Email sales pelsue com
2. and workers to possible serious injury or death 3 Visually inspect the product and all auxiliary components and equipment before using Correct any problems before using the equipment 4 Securely anchor the product before using 5 only certified anchor and connector components in your system 6 Use only an approved full body harness for the workers Page 1 0 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 4 4 Operating Safety continued 7 Always work in teams One person is to work in the confined space entrant and the other is to attend to the entrant attendant Pelsue recommends an additional attendant rescuer for stand by in case of an emergency 8 Do not exceed the capacity of the system at any time see section 5 1 9 Establish a regular training program for new and experienced workers 10 Establish a detailed inspection program for your equipment and document the findings Return the equipment to the manufacturer for repair if any problems are found 11 Plan your work program before starting Have the required people equipment and procedures available to do the job 12 Do not use the equipment around physical or environmental hazards This list includes but is not limited to Corrosion that may affect the structural integrity of the lifeline or other components Chemicals which can degrade components a manner which not be visuall
3. 1215 Quality Policy Pelsue Product Warranty 2 0 usus eee ewe te eee eee Introduction amp Product Information 7 Serial Number ON tee eee Configuration amp Assembly 8 BU Aenea ees MAIO oo aus u s uqa tasas aa 9 a Warning Statement 42 E Safety Alert Symbol General Safety Information 4344 2 2 ee Operating Safety Maintenance Safety New Operator Safety Information 1 Product 12 Product Description amp Capabilities eso Product Installation amp Set Up Maintenance amp Inspection 16 O l Conus ss Maintenance O2 Inspection OS Inspection Log OQ Storage 19 Contact 19 4 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 1 0 General Information 1 1 Quality Policy T A Pelsue Company Quality Policy OUR GOAL IS THE PURSUIT OF NEVER ENDING IMPROVEMENT IN PRODUCT QUALITY AND BUSINESS SYSTEMS METHODS TO BE EMPLOYED INATTAINING THIS GOAL WILL INCLUDE NEW PRODUCT QUALITY PLANNING EMPLOYEE TRAINING AND
4. 350 LBS 159 KG Factor of Safety when used with davit 4to 1 Features clamp upon a wide variety of wall thick nesses minimum amp maximum provided above Provides an anti friction lined receiver compat ible with any Pelsue Davit System e Constructed primarily of lightweight amp corro sion resistant powdercoated aluminum Independently adjustable clamping jacks will allow for inconsistencies in wall thickness e Structure easily disassembles for storage or transport Materials amp Construction e Main Structure 6061 Series Aluminum Powdercoated e Clamping Jack Screws SAE Grade 8 Steel Threaded Rod Anti Friction Liners ABS or CPVC Hardware Plated Steel Figure 5a DSR ADJ Loading Diagram Additional Requirements amp Notes TEST LOAD APPLIED AS SHOWN 350 LB 159 KG Maximum Capacity The load rating given here supercedes any load rating reported for an installed davit system The capa bilites of the davit system are limited by the base sytem DSR ADJ Wall Sleeve must be secured in place via all of the clamping jacks prior to use order to ensure compliance the structure to which the DSR ADJ is secured must be capable of withstanding all of the loads imparted to it by the device Installation of the device on tapered walls non vertical may result in slippage of the screws when under load extreme care must be taken
5. Sleeve is now ready to accept a Pelsue Davit System a Insert davit until base of center post firmly contacts the inside bottom of the receiver sleeve WARNING DSR ADJ Adjustable Wall Sleeve is only approved for use and certified when used in conjunction with Pelsue PNUH Series Davits b Refer to Davit Product Manual for proper instal lation and use Figure 5d DSR ADJ Installation Step 4 5 Install winches and or rescue devices as necessary on the davit Operate all equipment in accordance with relevant governing safety standards and within all of the manufacturer s instructions ratings and reported limitations DANGER Be aware of system creep movement when installing on tapered non vertical walls If excessive creep is Figure 5e DSR ADJ observed discontinue use of the system immediately and Installation Step 5 secure the installation 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 1 5 6 0 Maintenance amp Inspection MAINTENANCE amp INSPECTION Read understand and follow the Product Manual signs 3 Keep instructional and safety signs clean and legible at on the product before using maintaining or inspecting the all times Clean or replace as required equipment 4 Lubricate product as per instructions in Section 6 ANSI and OSHA require a regular inspection program 5 for all confined space entry retrieval equ
6. and follow the Product Manual and all safety signs before using maintaining or inspecting the equipment 2 Refer to and follow applicable standards and regulations Comply with requirements of local regulations for your applications 3 Establish an equipment use training program for inexperienced employees Only trained competent persons shall use the equipment An untrained operator is not qualified to operate the system Have a first aid kit available for use should the need arise and know how to use it Provide a fire extinguisher for use in case of an accident Store in a highly visible place Install and properly secure all guards and shields before operating QO as Wear appropriate protective gear This list includes but is not limited to Ahard hat Protective shoes with slip resistant soles e Heavy gloves Protective clothing e Face Protection 8 Review and follow the Pre Operation Checklist before using a component in the system or system itself 9 Establish a regular maintenance and inspection program with your equipment and maintain detailed records 10 Review safety related items and operating instructions with all personnel on a regular basis 4 4 Operating Safety 1 Read understand and follow the User Manual and signs the product before using maintaining or inspecting the equip ment 2 Train all operators before allowing them to use the product An untrained operator exposes themselves bystanders
7. shipment to the original buyer for a period of 3 months 90 days In the event of failure of any components of a Pelsue product within the warranty period service must be pre approved by the T A Pelsue Company and service must be performed by the T A Pelsue Parts and Ser vice Department in Englewood Colorado or at the option of the T A Pelsue Company service may be performed at any designated service center which may include any authorized service center for the component manufacturer Unauthorized repairs will not be covered by this war ranty Damage or failure due to misuse mishandling or unauthorized modifications will not be covered by this warranty Unless otherwise agreed the T A Pelsue Company shall repair or replace the defective components within 30 calendar days of notice of failure T A Pelsue Company s obligation hereunder shall be limited to the repair or replacement of the product or component as set forth above and shall not include any liability whatsoever for damages caused by such failure including but not limited to consequential or incidental damages flowing from use or lack of use of product Any replacment repair modification installation or other service performed by the T A Pelsue Company shall be warranted by the remainder of the unexpired period of the warranty or for period of 90 calendar days whichever is longer All materials or parts returned for credit or warranty shall be returned onl
8. the system Remember you are the key to safety Good safety practices not only protect you but also the people around you Make these practices a working part of your safety program Be certain that everyone operating this equipment is familiar with the procedures recommended and follows safety precautions Remember most accidents can be prevented Do not risk injury or death by ignoring good safety practices System owners must give operating instructions to operators or employees before allowing them to use the equipment and at least annually thereafter most important safety device on this equipment is a safe operator It is the operator s responsiblility to read and understand all safety and operating instructions in the manual and to follow these Most accidents can be avoided A person must understand the operation of this equipment and be trained in it s useage before operating the equipment An untrained operator exposes himself and others to possible serious injury or death Do not modify the equipment in any way Unauthorized modification may impair the function and or safety and could affect the life of the equipment Think SAFETY Work SAFELY 4 1 Warning Statement uumuax z as t WARNING Products manufactured or sold by T A Pelsue Company are intended for use by professionals trained and experienced in the use inspection and maintenance of these products Pa
9. 01 Date 05 02 08 Figure 5b DSR ADJ Installation Step 2 Page 13 5 2 Product Installation amp Set up continued aa s x 3 The next installtion step is to secure the device to the wall Follow the proceeding steps refer to Figure 5c a Push the head assembly sleeve as close to the wall as possible b Remove the detent pin and slide the aft support along the spanner tube until it contacts the wall then back up the aft support just enough so that the detent pin can be inserted into the closest hole c Tighten all clamping screws by turning them clockwise for best installation turn each of the screws an equal amount so that each of them has a uniform amount of thread showing d All screws should be tightend sufficiently by hand so as to prevent movement of the system along the wall when loaded e Ensure that the spanner tube is contacting the top of the wall as flat as possible and that the entire device is securely clamped to the wall b SLIDE AFT SUPPORT TO WALL AND INSERT PIN a PUSH SLEEVE AS CLOSE TO WALL AS POSSIBLE c TIGHTEN ALL CLAMPING SCREWS Figure 5c DSR ADJ Installation Step 3 Page 1 4 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 5 2 Product Installation amp Set up continued 4 The secured DSR ADJ Adjustable Wall
10. Part 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping PELSUE ISO 9001 Certified T A Pelsue Company 2500 South Tejon Street Englewood Colorado USA 80110 Tel 800 525 8460 or 303 936 7432 Fax 303 934 5581 Internet www pelsue com Email sales pelsue com PELSUE TRADITION INNOVATION ince our inception in 1963 the T A Pelsue Company has designed and manufactured high quality equipment to improve the personnel effi ciency and working conditions in various under ground confined and outdoor areas Founded by T Allen Pelsue the company has estab lished a continuing reputation for excellence in the production of fine products for a broad spectrum of industry throughout the world 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 ISO 9001 Certified Now in our second generation of family direction continued commitment to innovation and quality makes Pelsue a leading source of equipment for many types of confined spaces We specialize in safety retrieval fall arrest ventilation cable placing splicing and maintenance nationally and abroad With more than 70 000 square feet of facil ities available Pelsue continues the dedication that has made us pre eminent in this field Page 3 Table of Contents Section Description Page uu usss ss General Information 5
11. UTILIZATION OF EMPLOYEE INVOLVEMENT GROUPS TO SOLVE PROBLEMS IN AN INCREASINGLY COMPETITIVE MARKETPLACE ENSURING CUSTOMER SATISFACTION IS ONE OF THE DIFFERENTIATORS THAT SETS YOU APART FROM THE PACK AND YIELDS A COMPETITIVE ADVANTAGE THEREFORE WE WILL SUPPORT TOTAL CUSTOMER SATISFACTION BY IMPLEMENTING THE ISO 9001 QUALITY SYSTEM AND PROVIDING THE NECESSARY ATMOSPHERE AND TRAINING TO NURTURE THIS CONCEPT THROUGHOUT OUR ORGANIZATION WE WILL MAKE EVERY BUSINESS DECISIONAS THOUGH THE QUALITY OF THE PART OR SERVICE PROVIDED WAS DESTINED FOR OUR OWN OR OUR FAMILY S USE WE WILL ALWAYS THINK QUALITY FIRST EVERY T A PELSUE COMPANY EMPLOYEE IS EXPECTED TO COMMIT TO THIS PHILOSOPHY IN THE PERFORMANCE OF HIS OR HER DAILY TASKS QUALITY FIRST T A PELSUE COMPANY SENIOR MANAGEMENT TEAM 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 5 1 2 Pelsue Product Warranty rO II a Usw lt Oy cF Fv su BE SsO ee Pelsue products are designed and engineered to perform as stated in published specifications Quality materials and workmanship are used the manufacture of this product With regular maintenance and proper care Pelsue equipment provides many trouble free hours of opera tion The T A Pelsue Company warrants to the buyer that the Hoist Product furnished will conform to specifications and will be free from defects in material and workmanship from the date of
12. WELDMENT AFT SUPPORT ALUMINUM 4 3 500346 001 WELDMENT SPANNER TUBE 36 1 4 LONG 500340 001 ASSEMBLY FORWARD SUPPORT amp DAVIT SLEEVE Figure Model DSR ADJ 0 Assembly Diagram amp Parts Llst Verify that all parts are present before completing assembly 1 Slide head assembly Item 3 onto the spanner tube 4 at the end with the single hole 2 Fasten the head assembly item 3 to the spanner tube item 4 utilizing the prvoded fasteners items 7 8 and 9 only slightly tighten with wrenches so that washers are securely held against the structure 3 Slide aft support item 5 onto the spanner tube item 4 opposite of the head assemblty so that it is oriented as shown in figure 3a Pin in place with detent pin Item 10 the detent pin should be secured to the aft support item 5 via a lanyard 4 Thread clamping screws item 6 into the head assembly item 3 the aft support item 5 at the inserts so that the pointed ends are directed inwards as shown in figure 3a 5 System is ready for use Refer to parts list above if replacement parts are required Replacement parts be ordered from the Pelsue Company at 800 525 8460 Page 8 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 4 0 Safety The following section will address the safety precautions which must be adhered to when working with Pelsue
13. al Number Date Purchased Place a check N in the box if item is acceptable place an x X in the box if item requires maintenance or repair Overall Clampin Pins amp ping Labels Notes Structure Screws Fasteners Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 1 7 6 3 Inspection Log continued Overall Clamping Labels Pins amp Structure Screws Fasteners Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Inspector print amp sign Page 1 8 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 7 0 Storage Prior to storage the product should be thoroughly inspected and maintained Repair or replace any worn or damaged components to prevent any unnecessary down time at the next use Follow this procedure 1 Thoroughly clean the entire unit using a mild soap on the frame and labels
14. confined Space Safety equipment such as the Model DSR ADJ Adjustable Wall Sleeve Any user must familarize themselves with the information in this section before utlizing the equipment SIGNAL WORDS Note the use of the signal words DANGER WARNING and CAUTION with the safety messages The appropriate signal word for each message has been selected using the following guidelines DANGER Indicates an imminently hazardous situation that if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations or for hidden or unseen hazards WARNING Indicates a potentially hazardous situation that if not avoided could result in death or serious injury and includes obvious and hidden hazards It may also be used to alert against unsafe practices CAUTION Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices You are responsible for the safe operation maintenance and inspection of your Pelsue DSR ADJ Adjustable Wall Sleeve You must ensure that anyone who will operate maintain inspect or work around the equipment be familiar with the operating and maintenance procedures and related safety information contained in this manual This manual will take you step by step through the workings and capabilites of the DSR ADJ system and alert you to all good safety and operating practices while using
15. e general operation of the Pelsue Model DSR ADJ Adjustable Wall Sleeve The instructions contained within this section should be adhered to each and every time the product is used Any person tasked with installing or operating the piece of equipment should be familiar with these procedures 5 1 Product Description Capabilities The DSR ADJ Adjustable Wall Sleeve is built from structural aluminum and has several steel and or engineered plastic components The Model DSR ADJ is specifi cally designed for confined space entry and or rescue amp retrieval applications The model DSR ADJ is intended to provide a receiver sleeve for a Pelsue PNUH Series aluminum davit system By straddling a top accesible wall and clamping in place via the integral clamping screw jacks the DSR ADJ provides a secure and compliant receiver for a Pelsue Davit System All specifications instructions and procedures provided within this manual or upon Pelsue Specification Documents are based upon and only valid for usage with a Pelsue PNUH Series aluminum davit system The T A Pelsue Company can not verify equipment safety and or compliance when utilized with anything other than a Pelsue PNUH series davit system Adjustable Wall Sleeve Model DSR ADJ General Specifications e Minimum Allowable Wall Thickness 1 25 4 mm Maximum Allowable Wall Thickness 23 1 4 590 6 mm Structure Weight 49 LBS 22 2 KG Load Capacity Davit End
16. ipment and to maintain documented results of these inspections Follow the inspection procedure contained in this manual and use the inspection form to document the results Remove the equipment from service if a problem is found during the inspection Return to an authorized repair depot or the factory for service 6 1 Maintenance For the most part the Model DSR ADJ is intended to ba a maintenance free piece of equipment however several steps can be taken to keep the system in top notch working order and also extend the working life of the product Before Each Use 1 Visual Inspection Perform a complete visual inspection Refer to section 6 2 for guidelines and take any maintenance steps that are necesarry Annually 1 Clean Product Use a damp cloth and mild soap to clean the structure and labels of dirt and residue Be sure the labels are legible replacements are available from Pelsue 2 Complete Inspection Perform a thorough inspection paying attention to the bullet points provided within section 6 2 Record results and keep documentation Alog has been provided in section 6 3 specifcally for the recording of the dates amp results of annual system inspections Periodic Factory Service Inspection It is recommended that the product be serviced by a factory authorized service center or the manufacturer after a period of three years Extreme working conditions may indicate the necessity to increase the frequency Fac
17. manual covers the Pelsue Model DSR ADJ Adjustabel Wall Sleeve Use the Table of Contents or Index as a guide to find specific information Keep this manual handy for frequent reference and to pass on to new operators Establish a regular training program for experienced and new operators per this manual Establish a regular maintenance and inspection program to keep the equipment in top condition A WARNING This product is a part of a man rated confined space entry retrieval system The user must read understand and follow the instructions contained in this manual for each component or total system before using this equipment Establish an appropriate training maintenance and inspection program for your people and the equipment Failure to follow these instructions could result in serious injury or death 2 1 Serial Number Product Serial Number Always give your dealer the serial number of your Pelsue S N confined space entry retrieval product when ordering parts MODEL or requesting service or other information DOM The serial number decal will appear as shown in Figure 2a at right and is located by the davit receiver at the head assembly Figure 2a Serial see Figure 2b A Space has been provided below for the Number Plate recording of the serial number for future reference NUMBER MODEL DSR ADJ Serial Number Date of Manufacture DOM Figure 2b Serial Number Decal Location 500830 001 Pr
18. od condition remove from service and tag for shipment to an authorized repair depot or the factory for re work Using a product that is not in good condition can lead to a hazardous condition for user or entrant s Perform a comprehensive inspection procedure on a regular basis at least annually per the Inspection Section of this manual Document the results using the sample form and retain for your files A detailed inspection is required after each duty cycle x err lation will provide suitable proximity to the work e i area yet minimize obstructions during use and af in the event a rescue is necesarry Once a _ 5 _ ion i U U location is chosen q Z a Place the assembly on a secure flat surface Turn all clamping screws counterclockwise until all of the pointed ends are recessed into the aluminum structure Remove the detent pin from the aft sup port and slide the aft support a distance along the spanner tube that will allow the aft support and head assembly to rest on opposite sides of the installation wall refer to Figure 5a Place DSR ADJ Sleeve over the instal lation wall IWARNING user must ensure that the wall chosen for device installation will sustain the loads imparted to it by the proof loaded device 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision
19. oduct Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 7 3 0 Configuration amp Assembly Upon initial receipt of the Pelsue Model DSR ADJ inspect the packaging for any evidence that the product may have been damaged in shipment While unpacking the Pelsue Model DSR ADJ Adjustable Wall Sleeve inspect all of the components for damage If damage to any of the components is discovered DO NOT USE THE PRODUCT Alert the shipping carrier immidiately of the damage to the shipment The Model DSR ADJ may be shipped assembled or unassembled depending upon the shipping method If the prod uct is shipped unassembled a simple assembly procedure is required First verify that all of the parts are present refer to figure and parts list provided below and then assemble as shown in the figure below ITEM _ PART DESCRIPTION 14 121529 001 DECAL PELSUE VERTICAL WITH P LOGO 2005 2 13 103299 001 DECAL FOR SERVICE PARTS RED ON CHROME 12 500205 LB1 LABEL SERIAL NUMBER MODEL NUMBER DOM 11 119385 003 SCREW U DRIVE 8 X 1 2 LONG ZINC PLATED 10 500408 001 PIN amp LANYARD 1 2 D X 4 5 GRIP 9 100050 015 WASHER FLAT 5 8 TYPE USS A W PLATED 8 100048 124 LOCK NUT 5 8 11 NYLON INSERT 7 100530 017 SCREW HEX HD 5 8 11 UNC X 5 1 2 PLATED 6 500343 001 JACK SCREW ASSEMBLY GRADE 8 6 825 LONG 5 500350 001
20. r must read understand and follow the instructions in the manual No one should be allowed to use the equipment without training The training should be reviewed with experienced operators on a regular basis At regular intervals perform a detailed inspection of the equipment and document the results Remove from service if deficiencies are found Alterations or misuse of this equipment or failure to follow instructions may result in serious injury or death It is the responsibility of the owner s organization or operator to read this manual and to train all other operators before they start working with the equipment Follow all safety instructions exactly Safety is everyone s business By following recommended procedures a safe working environment is provided for the operator bystanders and the area around the worksite Untrained operators are not qualified to operate the equipment Many features incorporated into this equipment are the result of suggestions made by customers like you Read this manual carefully to learn how to operate the equipment safely and how to set it to perform as intended By following the operating instructions in conjunction with a good maintenance program your product will provide many years of trouble free service 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 1 1 5 0 Product Operation The following section will address the capabilities and th
21. raprofessional users such as volunteer rescue workers and sportsmen involved in risk sports such as climbing and Failure to read and heed all labels and instructions may result in injury or death Inspect all components before caving will be held to the same standard of experience and and after each use and remove from service if any training as professionals damage or defect is found Keep product free from dirt and moisture Do not leave a suspended load Technical rescue rappelling climbing and the training unattended Do not exceed maximum rated loads involved are hazardous activities Each situation has its own unique conditions and must be evaluated Effective risk management comes from experience proper training and good personal judgement 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 Page 9 4 2 Safety Alert Symbol SAFETY ALERT SYMBOL This Safety Alert symbol means ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED The Safety Alert symbol identifies important safety mes sages on your Pelsue Retrieval Product and in the manual When you see this symbol be alert to the possiblility of personal injury or death Follow the instruction in the safety message Why is this symbol important to you 3 BIG Reasons Accidents Disable and Kill Accidents Cost You Money Accidents Can Be Avoided 4 3 General Safety Information 1 Read understand
22. tory servicing shall include but not be limited to an intensive inspection and cleaning of all internal and external components Failure to provide proper service may shorten product life and could endanger performance or function 6 2 Inspection M When completing an inspection of the Model DSR ADJ Adjustable Wall Sleeve the following specific items should be checked 1 Labels Check that all the labels are clean and legible Clean the labels if any are dirty using mild soap and a damp cloth Replace if any are illegible 2 Fasteners Check that all screws and other fasteners are tight Tighten if any are loose Replace if any are missing 3 Structure Check the frame for cracks dents bends or breaks If there are major dents or any other structural damage the unit should be removed from service and returned to the factory for repair 4 Clamping Screws All of the clamping screws should be checked for proper operation All screws should turn freely and not bind or squeak excessively Oil or grease should be applied to the threads periodically in order to inhibit corrosion or damage If metal shavings or fragments are observed at any time on the clamping screws the system should be removed from service and a service center should be contacted regarding repair Page 1 6 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 6 3 Inspection Log Model Number DSR ADJ Seri
23. when utlizing the DSR ADJ on tapered walls if excessive slippage of the jacking screws is observed use of the device must be discontinued immidiately until the installation can be secured Page 1 2 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 5 2 Product Installation amp Set up Installation and set up of the DSR ADJ should be performed following the proceeding steps 1 It is necessary to perform a detailed visual inspection prior to using the product If deficiencies are found remove the product from service and contact the T A Pelsue regarding repair This checklist should be used as a guide to determine whether the equipment is in good operating condition prior to using Equipment that is not in good condition can endanger the safety of the entrant during use The visual inspection must include but is not limited to the following items 1 2 3 2 Choose location on a wall where instal Check that the product has no structural defects such as dents bends cracks or ruptures Ensure that all product rating amp warning labels are clear and legible Perform a Functional check a Verify that aft support slides freely upon the spanner tube and locks into position b Ensure that all clamping screws turn freely and that the threads are in good condition c Check all hardware nuts bolts washers amp safety pins for defects If the product is not in go
24. y identified Toxic gases Rescuers or workers be killed in toxic environments Heat or elevated temperatures Moving machinery Workers or auxiliary equipment be contacted by or pulled into moving components Sharp edges Workers or the rescue equipment can be injured by or damaged by sharp edges or components Electrical hazards Stay away from power lines or components carrying electrical power Overload Do not overload the system at any time during operation see section 5 1 Follow confined space regulations and standards 4 5 Maintenance Safety 1 Read understand and follow the User Manual and signs on the product before using maintaining or inspecting the equip ment 2 ANSI and OSHA require a regular inspection program for all confined space entry retrieval equipment and to main tain documented results of these inspections Follow the inspection procedure contained in this manual and use the inspection form to document the results see section 6 0 3 Keep instructional and safety signs clean and legible at all times Clean or replace as required 4 Remove the equipment from service if a problem is found during the inspection Return to an authorized repair depot or the factory for service 4 6 New Operator or Owner EE The Pelsue DSR ADJ Adjustable Wall Sleeve is designed to assist a person entrant to enter a confined space and assist in exiting if required Every new operato
25. y with prior approval and will be subject to factory inspection before credit is allowed Parts claimed defective will be replaced upon request and will be invoiced as purchased subject to credit when the parts claimed to be defective have been received and examined by the factory This warranty is expressly in lieu of all other warranties expressed or implied including any warranties of merchantability or warranties of fitness for any particular use and all other obliga tions or liabilities in connection with the sale of this equipment T A Pelsue Comapny 2500 South Tejon Street Englewood Colorado 80110 800 525 8460 Page 6 500830 001 Product Manual Model DSR ADJ Adjustable Davit Sleeve Clamping Revision 01 Date 05 02 08 2 0 Introduction amp Product Information E Congratulations on your choice of a Pelsue DSR ADJ Adjustable Wall Sleeve to compliment your confined space entry retrieval operation This equipment has been designed and manufactured to exceed confined space requirements and regulations in order to meet the needs of the discriminating operator for the efficient and safe entry or retrieval of personnel from a confined space Safe efficient and trouble free operation and maintenance of the system requires that anyone who will be operating maintaining or inspecting the equipment read understand and follow all the operation safety maintenance and inspec tion instructions contained within this manual This

Part #500830-001 Product Manual

Contents

Download Pdf Manuals

Related Search

Related Contents