HT270.02 User`s manual - Föhrenbach Application Tooling nv.
Contents
1. may be actuated 2 Place Clincher connector on the anvil r 3 Place cable well positioned in the connector 4 Close hand tool by moving the handle and hold Clincher connector with cable in place HT270 02 User s Manual Rev 01 Date April 2013 Page 3 6 www foehrenbach be F hrenbach Application Tooling 5 When the hand tool is completely closed the movable handle may be returned to its standing position x r 6 Repeat procedure 1 4 when a Clincher connector is used with more than 4 ositions Note The hand tool has stops which prevents opening the tool before the clinch action is complete Should it be necessary the stop can be released by turning the ratchet wheel in the direction indicated by the arrow Keep the movable handle under light pressure during this operation HT270 02 User s Manual Rev 01 Date April 2013 Page 4 6 www foehrenbach be F hrenbach Application Tooling Attention In order to warrant the termination quality verify constantly the clinch quality and clinch height in order to verify the quality and take the responsibility related to the produced terminations This manual is describing only a production means For all termination and connector related issues please follow the instructions as described in the FCI Technical Application TA 372 4 Adjustments and maintenance The tool is adjusted by Fohrenbach Application To2. H1270 02 Clincher Hand Tool User s Manual Revision 01 Date April 2013 F hrenbach Application Tooling www foehrenbach be F hrenbach Application Tooling 1 Purpose Termination of dedicated flex foils with FCI Clincher female or male connectors sre the successor of both the HT270 and HT274 2 Zoot description Cat No HT270 02 Single head clinch tool The tool terminates 2 3 or 4 connector per cycle The tool is equipped whit an anvil that can support up to 4 Clinch contacts Short set up times The tool kit consists of The manual clinch tool This users manual 3 The process In order to accommodate the applied size of Clincher connector the tool is featuring a press plate that can be adjusted for 2 3 or 4 contacts Before starting the termination process please be sure that the mentioned devices are correctly installed and adjusted Press plate not active Press plate active With your finger you can move the press plate between the active and not active position HT270 02 User s Manual Rev 01 Date April 2013 Page 2 6 www foehrenbach be 3 1 Ra Left and right press plate not active Left and right press plate active F hrenbach Application Tooling Terminating a flex foil After a proper adjustment of the press plates the tool is ready for terminating flex foils 1 Place the hand tool in your hand so that the movable handle
3. oling engineers for the characteristics of a test flex foil In order to warrant a proper operation the crimp height must be adjusted for the applied flex foil The crimp height and quality criteria in relation with the applied flex foil are described in the application note TA 372 or any update issued by FCI The crimp height can be adjusted as follows Remove the screw A and turn the wheel B in the or direction After completing the adjustment install screw A again h Regular checks must be made on press plate and anvil If necessary these parts may be cleaned Damaged parts must be replaced immediately Movable parts should be lightly oiled For any support please contact Fohrenbach Application Tooling F hrenbach Application Tooling Krijgsbaan 128 B 2640 Mortsel Antwerpen Belgium Tel 32 0 3 216 19 98 Fax 32 0 3 216 15 07 e mail application tooling foehrenbach be Website www foehrenbach be HT270 02 Users Manual Rewo Date April 2013 Page 5 6 www foehrenbach be F hrenbach Application Tooling 5 General specifications Colour black metal with red plastic levers Weight of tool 0 6 kg Size 205 mm x w 100 mm x h 22 mm 6 Input material and functional requirements 6 1 Cable Flex foil cable that fits to the applied Clincher connectors 6 2 Components Female and male Clincher connectors Number of positions 2 till 34 Product
4. part number Male clincher 66226 series Female clincher 65801 series Latched clincher 67516 series 7 Process output Due to the manual process the output capacity and quality are highly depended on the skills of the operator 8 Safety and ergonomics Apply the tool only for the target as mentioned in chapter 1 Purpose For operator safety it s necessary to apply eye protection Apply the tool only in a dry and clean environment Apply the tool only in a well lit area 1000 Lux Only skilful operators who are trained by Fohrenbach Application Tooling engineers are allowed to apply the tool The technical data in this publication has been carefully checked and assembled No liability from inaccuracies or errors is assumed The right to change or improve this document without notice is reserved HT270 02 User s Manual Rev 01 Date April 2013 Page 6 6 www foehrenbach be
Download Pdf Manuals
Related Search