Manual - KTI Networks
Contents
1. 8 Port SOHO Fast Ethernet Switch KS SOQHO 8 User s Manual DOC 130513 FCC Certifications F C This Equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in acommercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning CE This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class B for ITE the essential protection requirement of Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this documen2. and humidity 10 90 Non condensing e Donotplace objects on top of the unit e Do not obstruct any vents at the sides of the unit e Donotposition the unit near any heating source such as heater radiator or direct exposure to sun Prevent entering of water and moisture into the unit If necessary use dehumidifier to reduce humidity 2 Connecting the power Connect the power adapter to the power connector of the unit the green Power LED on the front panel should be lit Station Connection Connect each station to the switch by twisted pair cable Plug one RJ 45 connector into a RJ 45 port of the switch and plug the other RJ 45 connector into the station s network adapter Power on the switch and then system is ready Switches Connection In making a switch interconnection you could use any port to connect another switch with straight or crossover cable As all the ports support auto MDI MDI X function using a straight cable to make a Switch to switch connection is allowed For cable selection see the following table Cable Type Max Length 10Mbps Cat 3 4 5 UTP STP 100 meters ipt cat SUTPET Cable DSL Modem Fast Ethernet Switch Computer1 ER diet D Computer2 E Specification IEEE 802 3 10 BASE T IEEE 802 3u 100 BASE TX IEEE 802 3az EEE IEEE 802 3x hee B 10 100 Mbps RJ 45 Ethernet ports J 45 LOBASE T Category 3 4 5 UTP STP Cable Connections RJ 45 100BASE TX Cate
3. gory 5 UTP STP Network Speed 10 100 Mbps Auto negotiation Buffer Memory 96K Bytes Dimension 154mm L 85mm W 26mm H Operating 0 C 40 C 32 F 104 F t PR Storage 40 C 70 C 40 F 158 F Operating 10 90 RH non condensing Storage 5 95 RH non condensing External power adapter FCC CE Class B Humidity
4. t is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2012 All Rights Reserved Product Key Features Complies with 10M BASE T specifications of the IEEE 802 3 standard Complies with 100M BASE TX specifications of the IEEE 802 3u standard Supports full and half duplex for 10 100Mbps Provides 96K Bytes Buffer memory Wire speed packet filtering and forwarding rate Provides 1K MAC address Table Store and forward architecture filters fragment amp CRC error packets Supports IEEE 802 3az energy efficient ethernet Supports auto MDI MDI X crossover detecting and auto correction RoHS compliant VV ON NON ON No ON V WV Front Panel Please refer to the following description for the front panel t i mi j H LED Definition Status Operation Rear Panel The power adapter is plugged into the DC J ack of the rear panel and the rear panel is shown as below Installation Before you install the switch please check the following items in the package e One 8 port Fast Ethernet Switch e One Power adapter e One user manual 1 Operating Environment This switching hub must be installed and operated within the limits of specified operating temperature 0 40 C 32 104 F
Download Pdf Manuals
Related Search