User manual and parts book Model: 1430-1830
Contents
1. OTHER COMMENTS A ALWAYS FIX THE WEIGHTS ON THE MACHINE WITH THE SUPPLIED BRACKETS AND RODS IF THIS ISN T DONE CORRECTLY THE WEIGHTS COULD FALL OFF THE MACHINE WHILE MOVING AND INJURE PEOPLE OR DAMAGE PARTS NEVER CRAWL UNDER THE MACHINE MAKE SURE THE TRACTOR IS SECURED IN PLACE AND CANNOT START MOVING SWITCH OFF THE TRACTOR BEFORE GETTING OFF 21 16 0 OPTIONAL EXTRAS BOGY KIT Fig 15 If the tractor is not able to lift the Overseeder is it possible to use kit This makes it possible to lift and move the Overseeder with a lighter tractor The following Bogy Kits are available e Overseeder 1430 kit number 222 140 002 e Overseeder 1830 kit number 222 180 002 e Overseeder 2230 kit number 222 220 002 The kit contains cylinders drawbar bogy hydraulic hoses brackets rods rings and fixing material consisting of a number of bolts and nuts Fig 15 Mounting the parts of a bogy kit proceed as follows Replace nut 1 and pull back pin 2 Note that the rear roller does not fall on the ground Remove bush 3 and slide the pivot point of the bogy frame 4 in this place Insert pin 2 and mount nut 1 Mount cylinder bracket 5 6 to the frame with the supplied bolt and nuts Mount the cylinders 11 between the brackets and the bogy Note that the rod side pointing downwards and connection check valve inside Mount wheel shaft 8 to the frame using the suppl2. 0 30 0 60 40 80 0 40 0 80 0 35 0 70 0 55 1 10 45 75 O45 O80 O40 080 O65 130 52 68 0 60 1 20 0 50 1 00 0 85 1 75 58 62 0 70 1 40 0 60 1 20 1 00 2 00 62 58 0 80 1 60 0 75 1 50 1 20 2 45 68 52 1 00 2 00 0 90 1 80 1 40 2 80 75 45 1 30 2 60 1 10 2 20 1 90 3 85 80 40 1 50 3 00 1 40 2 80 2 20 4 45 95 25 2 80 5 70 2 60 5 30 4 15 8 40 Tab 1 These quantities are determined with a slit distance of 0 3 mm between the seeding roller and the pressure plate see section 14 0 for setting In practice the quantities described in Tab 1 may deviate to some extent due to other measuring working conditions In order to determine exactly the right seeding quantity for the seed used it is recommended to carry out a spreading test see section 14 2 12 6 0 TRANSPORTING THE OVERSEEDER The user is responsible for the transport of the Overseeder behind the tractor when travelling on public roads Check the national traffic rules In view of the weight of the Overseeder a maximum speed of 20 km h 12 4 mph should be observed while driving in open fields with the machine raised Higher speeds may endanger the driver and or other people and even damage the machine A Make sure the top link 3 see Fig 7 is connected and tensioned in the conveyor If this is not case the machine could sustain serious damage When the machine is lifted off the ground at least 20 of the weight of the tractor must rest on the front axle 7 0 DRIVING
3. SPEED The driving speed is limited to 12 km h 7 5 mph Higher speeds are not recommended in view of excessive wear and damage that may occur to the machine due to for example rocks in the ground 8 0 GENERAL REMARKS ON THE USE OF THE OVERSEEDER Some general remarks tips on the use of the Overseeder A field can be tilled 2 or 3 times in different directions in order to obtain a higher seeding density and for seeding in a diamond shape Do not make sharp turns preferably drive in straight lines to avoid damaging the machine and or the ground When hitting a hard object in the soil the cutting elements may be burred damaged Try to file burrs away or replace the cutting element When the cutting elements become wet the seed may stick and accumulate between the cutting elements Make sure the cutting elements do not become wet or postpone the work NEVER drive backwards while the running wheel is on the ground 9 0 OPERATING THE OVERSEEDER TEKEE Before using the Overseeder in the field check the following 1 Are there any loose objects in the field Remove these first 2 Are there any slopes The maximum slope this machine can work on is 20 degrees Always work downhill 3 Does the ground contain hard objects If so use the Overseeder at a low speed and adjust the working depth 4 Is there any danger of flying objects such as golf balls which may distract the attention of the driver If so do NOT use the Overs
4. note All information and technical specifications provided at the moment that this document is published are the most recent ones Design specifications may be changed without prior notice This document is a translation of the original operating instructions Upon request the original operating instructions are available in Dutch GUARANTEE CONDITIONS THIS OVERSEEDER COMES WITH A GUARANTEE FOR DEFECTIVE MATERIALS THIS GUARANTEE IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASING DATE OVERSEEDER GUARANTEES ARE SUBJECT TO THE GENERAL CONDITIONS FOR SUPPLY OF PLANT AND MACHINERY FOR EXPORT NUMBER 188 PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE REGISTRATION CARD For your own information please complete the table below Serial number of machine Dealer name Purchasing date Remarks H SAFETY INSTRUCTIONS The design of the Overseeder allows for safe use However this is only possible if the user fully observes the safety instructions given in this manual Read and understand Fig 1 the manual before starting to use the Overseeder Not using the machine as described in the manual Fig 1 may lead to injury and or damage to the Overseeder The Overseeder is solely intended for tilling lawns or areas where grass should grow Any other use is considered to be incorrect use The manufacturer does not accept any liability with
5. regard to damage resulting from incorrect use all resulting risks are the responsibility of the user Correct use also includes following the manufacturer s instructions for use maintenance and repair Before using the Overseeder inspect the area to be treated Remove any loose obstacles and avoid irregularities The Overseeder was constructed according to the latest technological knowledge and is safe to use Improper use maintenance or repair of the machine may result in injury to both the user and others This should be avoided Always use the Overseeder in combination with the appropriate tractor as described in the technical data All persons whom the owner assigns to operate maintain or repair the Overseeder must read and completely understand the operating manual and in particular the Safety Instructions section The user is responsible for a safe tractor Overseeder combination This unit must be tested in terms of noise safety and ease of use In addition user s instructions must be prepared Before using the Overseeder the user is obliged to inspect it for visible damage and defects Any changes of the Overseeder including its functioning that may affect its safety must be corrected immediately For safety reasons it is in principle forbidden to make changes in or additions to the Overseeder with the exception of those approved by the manufacturer If any modifications have been made to the Overseeder th
6. row distance 30 mm 1 27 Number of cutting elements 47 61 75 Recommended tractor 40 HP with minimal lift capacity 610mm behind the lift eyes of 3000 Kg 50 HP with minimal lift capacity 610mm behind the lift eyes 3600 Kg 6614 Ibs 7937 lbs 60 HP with minimal lift capacity 610mm behind the lift eyes 4450 Kg 9810 165 Seed tray capacity Maximum capacity theoretically at maximum speed 12 km h 7 5 mph and single passage Seeding density per 100 m 1076 4 2 230 8 1 ft 300ltr 10 6cu ft 182125 ft h 236375 ft h 360ltr 12 7cu Ft 16920 2 21960 27000 m7 h 290626 2 Normal seed 0 4 5 7 Kg 0 88 12 57 lbs adjustable in 10 steps Shipping dimensions LxWxH LxWxH 1310 x 1724 x 1160 1310 x 2144 x 1160 mm mm 51 6 x 67 9 x 45 7 51 6 x 84 4 x 45 7 LxWxH 1310 x 2564 x 1165 mm 51 6 x 100 9 x 45 7 Three point connection Lubricant 3 punt CAT 2 2 Standard parts Fillable back roller with scraper 5 gear sets for adjusting the seeding density Integrated seed spreading tray Manual container Seed tray with sight glass Seeding wheel adjusting to the area Independent cutting elements adjusting to the area Adjustment legs for storage Optional extras Bogy kit Weight kit Ballast gewicht Front Center rear 44 Kg 97 lbs 148
7. Kg 826 1 5 352 Kg 774 lbs 79 Kg 174 Ibs 193 Kg 425 Ibs 563 Kg 1239 Ibs 114 Kg Ibs 238 Kg 524 165 733 Kg 1612 Ibs 2 0 REMOVING THE MACHINE FROM THE PALLET Fig 6 Perform the following actions to remove the machine from the pallet and place it horizontally on the floor see Fig 6 1 D A NEVER CRAWL UNDER THE MACHINE Attach a cable to the lifting points 2 on both sides of the machine and to the top of the 3 point hitch 1 on the front A Overseeder 1430 Make sure the cable crane lift has the capacity to lift at least 2800 kg 6160 Ibs A Overseeder 1830 Make sure the cable crane lift has the capacity to lift at least 3500 kg 7700 Ibs A Overseeder 2230 Make sure the cable crane lift has the capacity to lift at least 4150 kg 9130 Ibs Lift the machine including the pallet about 100 mm 4 off the ground Remove the pallet by removing the bottom 3 point pins 4 Pull the pallet from under the machine Turn de locking pins 4 half a rotation and remove them Pull out the legs 5 and replace the locking pins 4 Lower the machine in a controlled and slow fashion until it is fully on the ground A 1 STAY CLEAR OF THE MACHINE CAN SLIDE 3 0 CONNECTING TO THE TRACTOR Checks prior to connecting the Overseeder Check the Overseeder for any visual damage and repair if safe operation of the m
8. Redexim User manual and parts book 5 verti drain redexim com 31 306933227 www redexim com The Netherlands F 31 306933228 Kwekerijweg 8 3709JA Zeist IN THE INTERESTS OF SAFETY AND ACHIEVING THE BEST RESULT IT IS VERY IMPORTANT THAT THIS MANUAL IS READ CAREFULLY BEFORE USING THE Model 1430 1830 2230 OVESEEDER Translation of the original user manual Serial nummer NOTE 1526 English 922 120 300 UK FOREWORD Congratulations with the purchase of your Overseeder To ensure long and safe use of this Overseeder it is of major importance to all users to read and understand this user manual Operation of this machine is not safe without full knowledge of the content of the manual The Overseeder is not an independently operating machine The user is responsible for using the appropriate tractor The user must also check the tractor Overseeder combination for safety aspects such as noise level adequate user instructions and any risks The Overseeder is solely intended for use on lawns and other areas where grass could grow On the next page you will first find the general safety instructions Every user must know and apply them After this a registration card is included This card should be returned for handling any future claims This user manual offers many instructions numbered in sequence This sequence should be observed An indicates a safety instruction An indicates a tip and or
9. The tractor engine must be switched off Increase the speed until the correct driving speed has been reached STOP SEEDING 1 2 3 Decrease the driving speed to about 3 km h 1 9 mph While driving raise the machine out of the ground Go to the following place and start again as described A It is absolutely imperative that the above procedures are followed If the machine is placed in the ground while standing still it may be seriously damaged A While driving lower the machine CAREFULLY AND IN A CONTROLLED WAY during the lowering process NEVER drive backwards when the running wheel is on the ground 14 11 0 DISCONNECTING THE OVERSEEDER The machine can be disconnected from the tractor as follows 1 Drive the Overseeder to a storage place with a stable even floor A Make sure the tractor is secured in place and cannot start moving A Switch the tractor off before getting off A l Be sure that the overseeder is stable on the floor and is locked against slipping before getting off the tractor 2 Turn the adjustable legs see fig 6 pos 5 downwards and lock them using the locking pins included 3 Slowly lower the machine until it stands on the ground 4 Loosen the top rod and remove it 5 Remove the lower arms from the tractor of the Overseeder A Make sure that the cutting elements do not touch the ground when storing the machine to avoid damage 12 0 TROUBLESHOOTING Problem Possi
10. achine cannot be guaranteed Check whether all nuts and bolts have been tightened properly Check whether all protective covers and safety stickers are in place on the machine and whether they are undamaged NEVER use the machine without them ay 1830 UO a 4 2 5 5 Fig 7 The Overseeder can be connected to the tractor using the 3 point hitch The method is as follows Fig 7 1 2 Remove the 3 point pins 1 and 2 Carefully back up the tractor so that the lifting arms 4 can be connected to the frame An Make sure the tractor is secured in place and cannot start moving An Switch the tractor off prior to getting off 3 4 5 6 7 Connect the lifting arms to the bottom 3 point pins 2 and secure them using the included locking pins Set the stabiliser of the tractor to a 100 mm sideways stroke Mount the top link 3 of your tractor and extend it until it is at the same height as the top 3 point hitch 1 of the Overseeder Connect the top link 3 to the frame using the top pin 1 and secure using the included locking pin Keep extending retracting the top link until the machine makes a 90 angle with the ground An Make sure all locking pins are secured 8 9 Start the tractor and lift the Overseeder off the ground Place the support legs 5 in the working position 10 4 0 ADJUSTING THE WORKING DEPTH The working depth
11. ally applicable regulations with respect to safety and working conditions must be observed For use on public roads the relevant traffic rules also apply Transporting persons is not permitted Do not use the Overseeder when it is dark during heavy rain storms or on slopes with a gradient of more than 20 degrees Before starting to work all persons operating the Overseeder must be familiar with all its functions and controls Connect the Overseeder to the vehicle that will pull it exactly according to the instructions Danger of injury Before driving off make sure you have a clear view both nearby and far away On both sides of the Overseeder safety stickers Fig 3 4 5 have been applied to the sideboards and to the back cover Fig 6 showing these warnings Make sure these safety stickers are always clearly visible and legible Replace them if they are damaged During operation make sure there are NO persons in the danger area of the Overseeder to prevent them from getting injured by moving parts Fig 3 Fig 3 Keep a distance of at least 4 metres Fig 4 Be aware of the maximum lifting capacity of the towing vehicle Wear suitable clothing Wear sturdy shoes with a steel tip wear long trousers do up long hair and wear no loose clothing Location of safety stickers Fig 5 921 280 402 Fig 5 EU DECLARATION Redexim BV Utrechtseweg 127 3702 AC Zeist the Netherl
12. ands declare entirely under our own responsibility that the product OVERSEEDER WITH MACHINE NUMBER AS STATED ON THE MACHINE AND IN THIS MANUAL to which this statement relates is in accordance with the provisions of the Machine Directive 2006 42 EG Zeist 1 6 2015 A C Bos Manager Operations amp Logistics Redexim Holland 120 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0 12 0 13 0 14 0 14 1 14 2 14 3 15 0 16 0 CONTENTS FOREWORD GUARANTEE CONDITIONS REGISTRATION CARD SAFETY INSTRUCTIONS EU DECLARATION TECHNICAL DATA REMOVING THE MACHINE FROM THE PALLET CONNECTING TO TRACTOR ADJUSTING THE WORKING DEPTH SETTING THE SEED QUANTITY TRANSPORTING THE OVERSEEDER DRIVING SPEED GENERAL REMARKS ON THE USE OF THE OVERSEEDER OPERATING THE OVERSEEDER START STOP PROCEDURE DISCONNECTING THE OVERSEEDER TROUBLESHOOTING MAINTENANCE ADJUSTING THE SEEDING SLIT OPENING ADJUSTING THE SEED TRAY SCRAPER SPREADING TEST OPEN AND CLOSE THE TOP UNIT OPTIONAL EXTRAS WEIGHT KIT OPTIONAL EXTRAS BOGY KIT NY 11 12 13 13 13 13 14 15 15 17 18 18 19 20 21 22 1 0 TECHNICAL DATA Model 1430 1830 2230 Working width 1 38 m 54 3 1 80 70 9 2 22 87 27 Working depth 5mm 20mm 0 19 0 78 Seeding speed Up to 12 Km h 7 5 mph Weight 1416Kg 3115 Ibs 1750Kg 3850 Ibs 2076 Kg 4567 lbs Seeding
13. ble cause Solution Seeding cuts are poorly shaped Seeding discs are worn Poor ground Bearings of the seeding discs are worn Too much dead leaves and roots in the top layer of the field Top rod incorrectly adjusted Seeding disks don t turn stuck Replace the seeding discs Lower the working depth Aerate irrigate the ground if it is too dry and repeat the tilling later Replace the bearings Remove the dead leaves and roots Increase the weight of the machine Correctly adjust the rod Loosen the disks Seeding cuts are not closed Slits are too wide Ground is too hard Rear roller not on the ground Lower the working depth Aerate irrigate the ground and repeat the tilling later Make it floating see chapter 4 The seed is not in the seeding cut Worn seeding discs Wrong working depth Seeding pipes funnels are blocked dirty Too wet conditions Replace the seeding discs Adjust the machine to the correct working depth Unblock clean Postpone the tilling 15 Problem Possible cause Solution Seed is spoilt from the seed tray Seeding slit too large Distance between the scraper and the seeding roller is too large The adjustment plate of the seeding slit on the side is leaking Readjust the seeding slit Set the scraper closer to the seeding roller Tape up glue The machine does not reach the re
14. can be adjusted by adjusting the sliding foot of the seed blades Loosen the bolts 1 Now move the sliding feet 2 to the desired depth from 5 to 30 mm working depth Fig 8 5 30mm 0 2 1 2 Fig 8 An Please note that front and rear sliding foot the same depth are set and parallel The rear roller should also be set to the desired depth The rear roller can also be mounted floating This can be done by loosening pin and lock pin 1 The spindles 2 can be mount in the seed hopper 3 Fig 9 lt The machine can be equipped with additional weights see chapter 15 and or filling the rear roller with water lt gt If the rear roller is filled with water empty it before it starts freezing 11 5 0 SETTING THE SEED QUANTITY The seed quantity can be set on the Overseeder Too Gear by using various change gears These provide various combinations for a broad range of settings see Tab 1 The gears have been marked with a number given in Tab 1 by changing the gears as indicated the required quantity setting is Bottom Gear obtained The different combinations of gears have been installed in the seed tray Fig 10 Gear Option Bentgrass Kentucky Bluegrass Ryegrass Bottom Top Kg 100m Lbs 1000ft Kg 100m Lbs 1000ft Kg 100m Lbs 1000ft 25 95 0 20 0 40 0 20 0 40
15. e present CE certificate becomes null and void and the person who made the modifications should himself make sure a new CE certificate is granted Inspect the Overseeder for loose bolts nuts parts before each use If present inspect the hydraulic hoses regularly and replace them if they are damaged or show signs of wear The replacement hoses must meet the manufacturer s technical specifications Always relieve the pressure from the hydraulic installation if present before carrying out any work on it NEVER use de Overseeder when protective covers and safety stickers are missing NEVER crawl under the Overseeder Tilt the Overseeder if you need to have access to the bottom NEVER step off the tractor while the engine is still running When carrying out maintenance activities adjustments or repairs make sure the Overseeder is locked to prevent it from sinking riding sliding away When carrying out any maintenance activities adjustments or repairs always switch off the tractor engine first remove the tractor key from the ignition and disconnect the PTO Fig 2 Fig 2 When carrying out any maintenance or repair activities make sure to use original Overseeder parts only This will ensure safety for the machine and its user Only authorised technical personnel may carry out adjustments and repairs to the Overseeder Keep an overview of repairs In addition to the instructions in this user manual the gener
16. eeder 5 Is there any danger of sinking or sliding away If so postpone the work 6 If the soil is frozen or very wet the work should be postponed until the conditions are more favourable 13 10 0 STARTING STOPPING PROCEDURE Before starting the seeding check the machine for the following points A While checking the machine tractor combination must be fully locked to prevent it from driving sliding sinking away The tractor engine must be switched off Check the seeding elements for damage and repair if necessary Check if the passage to the seeding elements is not blocked e g funnels Check if the machine is not wet or moist in particular the seeding device Check the seed spreading by rotating the running wheel 1 time counterclockwise Check if the drive is running smoothly START SEEDING The starting procedure is VERY important If this procedure is not followed exactly as described below serious damage may occur to the machine The procedure is as follows OiR ON Put the seed in the seed tray Set the required seed quantity using the change wheels see section 5 0 Drive to the place where you want to start Start with a driving speed of about 3 km h 1 9 mph While driving lower the machine carefully and in a controlled way until the seeding elements are cutting the ground A While adjusting the machine tractor combination must be fully locked to prevent it from 6 driving sliding sinking away
17. ied spacer 9 and the mounting plates 7 10 At the front of the machine must be mounted the draw bar 15 These can be mounted by fastening it with standard fixing pins at the lower 3 point plates Then install cylinder 16 with two stop cylinders 17 between the top 3 point suspension and drawbar using the included pins and circlips 13 14 Then place the various hydraulic couplings 12 and hoses See parts pages for exact position and sequence hydraulic components A 1 NEVER CRAWL UNDER THE MACHINE A H SURE THE MACHINE IS SECURELY PLACED 22 Fig 16 SETTING LIFTING LOWERING ORDER The Overseeder has a separately lifting system Fig 16 These are located at the front of the machine and can be set separately lifting the tow bar as wheelset The speed of lifting and lowering can be adjusted by rotating the restrictors 4 and 5 Clockwise slower Counter clockwise faster By more opening the restriction 4 than opening restriction 5 the front of the machine will be lowered or raised earlier The setting of difference for each circumstance should be adjusted experimentally When the correct setting is reached fix the throttle with the screw beside the knob Connect the machine to the tractor Adjust the pin 1 using the rings 2 of the stop cylinders 3 so that the machine is on working depth and slides with the cutting guides of the seed discs flat on the ground but still putting p
18. ll the seed tray too hard to the stop 8 Place the four bolts and nuts 6 which the seed tray 7 is mount on the lower frame 9 Place the cover plates 5 on the front and back side of the machine 10 Place the both funnel trays 4 and place the chain 3 11 Place the covers 2 back on the machine 20 15 0 OPTIONAL EXTRAS WEIGHT KIT Fig 14 You can use a Weight Kit this will help the machine to cut more easily in to the ground The following Weight Kits are available e Overseeder 1430 number 222 140 004 352lbs rear 222 140 006 192lbs inside e Overseeder 1830 number 222 180 004 563lbs rear 222 180 006 272lbs inside e Overseeder 2230 number 222 220 004 733lbs rear 222 220 006 352lbs inside The kit contains weights and fixing material consisting of a number of bolts and nuts and frame rear Fig 14 Inside weight The weights 1 can be placed and mount with bolts and washers 2 on the front beam of the overseeder When weights are needed at the center the seed tray needs to be opened On the inside of the machine it is possible to mount weights 4 5 on the frame with bolts and washers 5 See parts manual for exact mounting After mounting the weights the seed tray can be closed C See chapter 14 3 for opening and closing the seed tray Rear weight The weights 6 can be placed on the rear beam of the machine with a frame 6 See parts page for exact mounting
19. nd nuts 6 The distance between roller 1 and scraper 5 is default set to 0 8mm 0 03 and should be equally set along the entire width of the roller 18 14 2 SPREADING TEST If the seeding device needs recalibration for a certain seed type or if it must be checked for proper operation in accordance with the seed table see section 5 0 Tab 1 a spreading test is to be carried out This is done as follows see fig 12 1 Fig 12 Place the machine safely on the support legs on a level surface A 1 Make sure the tractor is secured in place and cannot start moving A 1 Switch the tractor off before getting off wy O 10 11 First of all check the seeding slit opening for correct setting see section 14 0 Put the seed that is to be calibrated into the seed tray 4 and spread it equally over the tray Remove the spreading tray 1 Remove pins 2 on both sides of the machine Remove the funnel tray 3 Slide the spreading tray underneath below the seed tray 4 Turn the wheel 5 13 full rotations counter clockwise Weigh the seed that is collected and multiply this by 4 4 1430 Weigh the seed that is collected and multiply this by 3 4 1830 Weigh the seed that is collected and multiply this by 2 8 2230 The result is the weight of the seed that is seeded per kg 100m Ibs 1000 ft Compare the results with Tab 1 Section 5 0 and do another spreading test if neces
20. orrect torque Use a chain spray Tension the tensioners of the drive chains Clean the seeding roller or replace it if necessary Adjust the seeding slit if necessary Carry out a spreading test Clean if necessary Repair or replace if necessary 17 14 0 ADJUSTING THE SEEDING SLIT OPENING If the seed production does not correspond with the table the seeding slit may need adjustment This is done as follows see fig 11 ee Loosen all lock nuts 3 Adjust bolt 4 such that a feeler gauge of 0 3 mm 0 01 can be slit just between the roller 1 and the adjustment plate Check all bolts 4 and calibrate the slit opening between roller 1 and adjustment plate 2 along the entire width of the machine to 0 3 mm 0 01 Turn roller 1 half a turn and measure the slit opening If necessary adjust it to 0 3 mm 0 01 by turning bolt 4 in or out Tighten the lock nuts 3 The split opening should be equal along the entire width of the roller The slit opening must have the same size as the smallest seed part This opening is default set to 0 3mm 0 01 14 1 ADJUSTING THE SEED TRAY SCRAPER When the seeding tray is spoiling seed the scraper setting may be incorrect To adjust this proceed as follows see fig 11 1 Loosen bolts and nuts 6 2 Move scraper 5 up or down until the correct setting has been obtained 3 Re tighten the bolts a
21. quired depth Tractor tensioning is too low Ground is too hard Top rod is incorrectly adjusted Too much dead leaves and roots in the top layer of the field Not enough weight Put drawing arms into a higher hole Aerate irrigate Correctly adjust the top rod Remove the dead leaves and roots Add weight 16 13 0 MAINTENANCE Time schedule Check point lubricating point Method Before each use Check for loose bolts nuts Presence and legibility of safety stickers Fig 5 Tighten the loose bolts nuts with the correct torque Replace if damaged or missing After each use Clean the machine Clean the machine with compressed air Don t use water After first 20 operating hours new or repaired Grease the roller bearings of the rear roller Check for loose bolts nuts Grease the drive chains Use EP 2 lubricating grease Tighten the loose bolts nuts with the correct torque Use a chain spray After every 100 operating hours Grease the roller bearings of the rear roller Check for loose bolts nuts Grease the drive chains Check the tension of the drive chains Check the seeding roller for dirt damage Check the seeding slit opening Check the seed quantity Check the seeding pipes funnels Check the seeding elements for damage Use EP 2 lubricating grease Tighten the loose bolts nuts with the c
22. ressure on the tow bar A WARNING BE CAREFUL IF THE CHOKES ARE OPENED TOO FAR THE MACHINE CAN LOWER VERY QUICKLY CREATING AN UNSAFE SITUATION 23
23. sary If the results of the spreading test do not reasonably match the calibration values check the seeding slit opening and adjust this if necessary see section 14 0 Remount the parts in reverse order 19 14 3 OPEN AND CLOSE THE TOP UNIT For service or placing center weights the seed tray needs to be opened proceed as follows 1 Drive the overseeder to a storage place with a stable even floor 2 Adjust the legs 1 downwards and lock them with the included lock pins A l Before step of the tractor be sure the overseeder is standing stable the floor and secured in place against sliding A I Switch the tractor off before getting off 3 Remove the covers 2 and then the chain 3 and both funnel trays 4 you can see now 4 Remove cover plates 5 on the front and back side of the machine 5 Remove the four bolts and nuts 6 which the seed tray 7 is mount on the lower frame 6 The seed tray 7 is free and can be pulled backwards A I Don t pull the seed tray to fast this can damage the machine I Beware of hands and fingers they may get caught between moving parts A 1 Don t pull the seed tray too hard to the stop To close the seed tray proceed as follows 7 Push the seed tray 7 forwards A 1 Don t push the seed tray to fast forward this can damage the machine I Beware of hands and fingers they may get caught between moving parts A 1 Don t pu
Download Pdf Manuals
Related Search