EV-13xxxx12 - Seco-Larm
Contents
1. 92 pixels NTSC 512 x 582 pixels PAL 2 1 interlace V 59 94Hz H 15 734KHz NTSC V 50Hz H 15 625KHz PAL Internal 1V pp composite output 750hms F2 0 3 6mm lens included 1 0 lux 0 45 gt 48dB Auto Electronic Shutter 1 60 1 100 000 sec NTSC 1 50 1 100 000 sec PAL auto auto 12VDC 125mA 22 140 F 30 60 C 14 113 F 10 45 C 33 16 X s 81 x 22mm 2 8 0z 80g Parts List 1 x Bullet camera 1 x Mounting bracket 3 x Mounting screws 3 x Screw anchors 1 x Manual F N iff NA iif TE tye Y F N j NA Sig NaN BEFORE STARTING 1 Do not mount the camera where it is exposed to rain or other moisture or in humid or dusty places 2 Do not point the camera at the sun Heat could damage the camera even when not in use 3 Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals INSTALLATION 1 Runa 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted if necessary 2 Screw the bracket into the back of the camera Make sure the adjustment plate is on the plastic screw between camera and bracket 3 Temporarily connect the camera to the 12VDC power supply 4 Temporarily connect the camera s female BNC connector to the video cable s male BNC connector 9 While watching the monitor hold the camera br2. ENFORCER CCD Burer Camera Manual TROUBLE SHOOTING The screen is blank Check that the camera is powered up Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen image is dim Clean the lens using a soft clean cloth Check that the light source is adequate The screen image has poor contrast Adjust the monitor s contrast knob Change the position of the camera The screen image flickers Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and Statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING This product was designed for indoor use only Mounting outdoors or exposure to rain or moisture could cause a dangerous electric shock damage the device and void the warranty Do not open the case of this device as there are no field serviceable components inside WARRANTY All SECO LARM products are warranted against defects in material and workmanship while used in normal service for a period of two 2 years from the date of sale to the original consumer c
3. acket against the wall by hand where it is to be mounted then twist the camera until it is certain that this mounting location is correct Use a pencil to mark the location of the three screw holes in the bracket 6 Disconnect the 12VDC power supply and video cable cords ENFORCER CCD Butcer Camera Manual Camera Bracket DC jack BNC connector female Thumb screw Adjustment plate Mounting screws 3 Screw anchors 3 aE G sh I Cy 4 Do not open or disassemble the camera There are no user serviceable parts inside 5 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on 7 Mount the bracket to the wall using the three included mounting screws If the wall is made of dry wall brick or similar material it may be necessary to use the three included screw anchors 8 Reconnect the 12VDC power supply and video cable Turn the monitor on and make sure the camera is sending the proper video signal 9 Adjust the camera angle a Loosen and tighten the bracket s thumb screw to turn the camera and change its angle relative to the bracket This ensures the camera is pointing in the right direction b Loosen and tighten the adjustment plate to rotate the camera on
4. its axis This rotates the angle of the video image 10 Tighten the bracket s thumb screw and the adjustment plate so that the camera does not move but not so tight that it cracks the case or bracket 11 Do a final test of the video camera and monitor
5. rt without the written permission of SECO LARM file BULLET IMU0803 P65 MANUAL EV 1324C12 amp EV 1354C12 14 CCD Color Bullet Cameras EV 1323B12 amp EV 1353B12 13 CCD B W Bullet Cameras SCc SECO LARM U S A INC Note CCIR PAL cameras available by special request only ENFORCER CCD Burer Camera Manual Specifications Type Chip Resolution Pickup elements Scanning system Sync Video output Lens Minimum illumination Gamma correction S N ratio Shutter control Backlight compensation Automatic gain control Power source Power consumption Storage temperature Operating temperature EV 1323B12 EIA EV 1353B12 CCIR B W camera Samsung 420 TV lines 1 3 CCD 510 x 492 pixels EIA 500 x 582 pixels CCIR 2 1 interlace V 59 94Hz H 15 734KHz EIA V 50Hz H 15 625KHz CCIR Internal 1V pp composite output 750hms F2 0 3 6mm lens included 0 1 lux 0 45 gt 48dB Auto Electronic Shutter 1 60 1 100 000 sec EIA 1 50 1 100 000 sec CCIR auto auto 12VDC 125mA 22 140 F 30 60 C 14 113 F 10 45 C Dimensions inc cord mounting 3 16 x s 81 x 22mm Weight Note CCIR PAL cameras available by special request only yy ase J Mee 2 8 02 80g 2 3 76 5mm gt 50 5mm EV 1324C12 NTSC EV 1354C12 PAL Color camera Sharp 380 TV lines 1 4 CCD 512 x 4
6. ustomer Our obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM For complete details regarding the SECO LARM warranty please contact SECO LARM FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class a digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 The information and specifications printed in this manual are current at the time of publication However SECO LARM s policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2003 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in pa
Download Pdf Manuals
Related Search