Home

Manual

1. electromagnetic interference Specifically the site you select should meet the following requirements The ambient temperature should be between 0 to 45 degrees Celsius The relative humidity should be less than 95 percent non condensing Surrounding electrical devices should not exceed the electromagnetic field RFC standards for IEC 801 3 Level 2 3V M field strength Make sure that the equipment receives adequate ventilation Do not block the ventilation holes of the equipment The power outlet should be within 1 8 meters of the product Connecting to Power This Converter is a plug and play device Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the converter and then attach the plug into a standard AC outlet Specifications Applicable Standards IEEE 802 3 10Base T IEEE 802 3u 100Base TX amp 100Base FX 1 TX por 1 FX pori Speed 10Base T 10Mbps for half full duplex 100Base TX FX 100Mbps for half full duplex Switching Method Store and Forward Forwarding rate 14 880 148 810pps for 10 100Mbps Per Unit 2 LEDs TX LNK ACT FX LNK ACT 54 2mm W x 80 3mm D x 21 9mm H 2 13 W x 3 16 D x 0 86 H 0 C 45 C OOF HOF 10 C 70 C AF 158 F 5 95 non condensing User s Manual 2
2. 02 3x compliant flow control Port status LEDs External AC to DC power adapter Used as a stand alone device Packing List When you unpack this product package you will find the items listed below Please inspect the contents and report any apparent damage or missing items immediately to our authorized reseller The Media Converter User s Manual AC to DC Power Adaptor One Channel Media Converter Ports The Converter provides one TX port and one FX port For the FX port it provides options of Multi mode fiber using SC ST VF 45 MT RJ or LC connector or Single mode fiber using SC or ST connector or WDM fiber using single SC connector For the TX port it uses RJ 45 connector and auto senses the speed of 10 100Mbps Front Panel amp LEDs LED Indicators The LED indicators give you instant feedback on status of the converter User s Manual 1 Media Converter 1O0FE 16 108 REY 99 LE ACT LWE AC TX LNK ACT Steady A valid network connection established FX LNK ACT LNK stands for LINK Flashing Transmitting TX or receiving RX data ACT stands for ACTIVITY Off Neither valid network connection established nor transmitting TX receiving RX data Installation This chapter gives step by step installation instructions for the Converter Selecting a Site for the Equipment As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or
3. Media Converter Preface This manual describes how to install and use the Ethernet media converter The Converter introduced here provides one channel media conversion between 10 100Base TX and 100Base FX The Converter fully complies with IEEE802 3 10Base T and IEEE802 3u 100Base TX FX standards In this manual you will find Product overview Features on the media converter Illustrative LED functions Installation instructions Specifications Introduction The media converter provides one channel for media conversion between 10 100Base TX and 100Base FX It can be used as a stand alone device Product Overview Product Features One channel media conversion between 10 100Base TX and 100Base FX Fiber media allows Multi mode fiber using SC ST VF 45 MT RJ or LC connector e Single mode fiber using SC or ST connector WDM single fiber bi direction transceiver Single mode WDM fiber using SC connector A type WDM single fiber bi direction transceiver transmits with 1310nm wavelength and receives with 1550nm wavelength B type WDM single fiber bi direction transceiver transmits with 1550nm wavelength and receives with 1310nm wavelength Auto negotiation of speed and duplex mode on TX port Auto MDIX on TX port Support Link Fault Pass Through 2048 MAC addresses 768K bits buffer memory Store and forward mechanism Non blocking full wire speed forwarding rate Support broadcast storm filtering Back pressure amp IEEE8

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents