Home
        TURBO TIMER USER`S MANUAL
         Contents
1.  end of the product s wire   lt A cut connector  wires  cut connector  with vinyl tape                                         METER INSTALLATION PART NAMES                                              Clean oil and dust from the   lt  Main unit      main unit and from the area T MIN Switch Lo TETE MODE Switch  where you wish to affix it   oubis sidsdi Change each setting PE aoi Change each mode    ouble sided tape     Make sure to securely affix j lt  i   Included  i  it with the double sided tape SZT    provided in the kit  eo SEC Switch   VA POW Switch  Do not reuse the tape  L Clean to remove Change each setting Power ON   OFF  it will lose adhesiveness  oil and dust           BASIC OPERATIONS        gt  Key ON     Engine not running                     gt  Turn power on by    pressing the St POW   Press Display Lamp  POW switch       gt  The mode will Auto Mode Time Display  MODE   Press    change with each Fe    Auto Mode i Auto setting of idling time in X If the idling time is 45 seconds  pressing of the  Current setting value dlsplay  accordance to running time   MODE switch     gt  Coie k yxy 4A    Yr  TL When set to the Auto Mod  moe  uo 5 final dot blinks e     Final dot blinks      Manual Mode Time Settings    v Idling Time can be set in 10 second increments  from 0 seconds to 9 minutes  50 seconds   Manual Mode                         X1 When in Auto Mode and idling time is  zero seconds the display will show    tf   final dot will blink      r   I   I   I   I   
2. I   I   I   I   I   I   I  When set to the Auto Mode  final dot oF  g SEC switch is used to change the  blinks during display  and turns off when l MIN oaa   PSEC   seconds nn m  set to the Manual and Heating Mode  l First dot lights up   FI g  uu  f  5 LI   l   I   I   I   I   I   L    MIN switch is used to change the     Current setting value display     iP Press MOP SEC men   Press MIN or SEC switch  gt  MIN inuti  n g mue 000 908          i Minutes Seconds    v    Heating Mode    i    Current sac display    Heating Time can be set in 10 second increments  If the POW switch is pressed while the 9 pay   gt  Press MIN or SEC switch from 10 minutes to 19 minutes  50 seconds       nde A   i a4 F  g Mri  timer is in operation the display will turn OO Ob Og MIN switch is used to change the    off and the engine will stop   gt MIN  minutes 4 7 10  EMN  L seo   ge  aO  138             While the Timer is operating  If you re   lease the emergency brake    F   in the  display will go off        Heating Mode Time Settings                Minutes Seconds SEC switch is used to change the    PSEC  secors ppa FOS     gt  Pressing the POW  switch turns the BT POW   Press Lamp OFF  power OFF                                  TROUBLESHOOTING        TROUBLESHOOTING FOR SOME SPECIAL CAR MODELS     Model of Car Possible Causes Possible Solutions       New SUBARU modele equip  The security system This is because the security system does   After stopping the engine  after idling has finished   loc
3. Oi vor     TTX   As of September  2008 No 1     TURBO TIMER TTX    USER   S GUIDE TURBO TIMER    Ultra Compact Design       Thank you for purchasing PIVOT    TURBO TIMER      Please read these instructions carefully before installing or using this device   Please do not lose this user   s guide  as you will held liable for the cost of reissuing it     Before installing      A NOTE Please be sure to check that    TURBO TIMER    operates properly before installing it in the car or  drilling holes for installation                         r    A CAUTION Improper use or disregard of these warnings may  result in the injury or death of people     A NOTE Improper use or disregard of these warnings may cause  injury to persons  damage the product and other things             When installing this product  we recommend that if technical knowledge be   comes necessary please consult a qualified mechanic      This product is for DC12V cars  installation cannot be carried out on cars with  other voltage batteries      Wiring should be carried out using the attached    cut connector    or by soldering   make sure to securely insulate all wiring parts with insulation tape  and confirm  that no wires are sticking out      Do not  in any manner  process  take apart  or make changes to this product      Do not install    TURBO TIMER    in any place subject to high temperature or any  place where water may be splashed      When double sided tape is used for an installation be warned that when h
4. itch was pushed  but An improper harness for your car model Make sure you are using the proper harness for When using the Timer in a car  no display appears  has been used  your car model  equipped operating with an auto       light control system  the lights may          The timer operates but the An improper harness for your car model Make sure you are using the proper harness for i     engine stalls  has been used  your car model  not turn off when using the Timer  even after the engine has stopped   The emergency brake has not been pulled is i i  The timer display reads up far erin y p Make sure to pull up the emergency brake  If this is the case  when using the    P   and doesn   t operate   Timer make sure to not use Auto  i Contact failure of BROWN wire  Check the BROWN wire connections or conditions  Mode for the light control system                       PIVOT CORPORATION 87 3  Shimookada Okada  Matsumoto shi  Nagano  390 0313 Japan TEL0263 46 5901 http   pivotjp com     
5. k the car door          E AOV oie ae E not operate while the engine is running  and activate the security system   The door lock function fo     sad  TOYOTA ARISTO i This is because the immobilizer and the P i ae i   Later JZS161 models  tea door lock system are interconnected  After stopping the engine  after idling has finished   lock the car door   Some of the K car The timer operates The polarity of the special harness is in  Switch the YELLOW and BLUE wires on the 3 pin coupler coming out  but the engine stalls  correct  from the Turbo Timer     X1 In some special harnesses the IG1  YEL   LOW  and IG2  BLUE  positions are re   versed  If this is the case  try switching    the YELLOW and BLUE wires of the 3    RED      RED   gt  Pi out   gt                                  A d the wire  pin coupler coming out from the Timer  YELLOW while BLUE  X2 Note  that doing this in other car models BLUE  Front  pressing in YELLOW  will render the Timer inoperative  so ae nes  please return the wires to their original  Present Condition   After Fixing   connection positions   The timer will not operate properly if the In order to increase the torque  increase the engine rotation to 1200   during idling torque is too weak  1500 rpm and turn off the key switch to start the timer operation   Trouble Possible Causes Possible Solutions Cars with Automatic Light            Controller  With key switch ON  POW Contact failure of BLACK wire  Check the BLACK wire connections or conditions   sw
6. ness to the 3 pin coupler cable of the main unit        The BLACK wire must be connected with the screw on the car body   3 pin Coupler     Connect the BROWN wire to the emergency brake  make sure to securely fasten it either by soldering  or by using the cut connector included in the kit   Emergency Brake Explanation of Wires from Main Unit Checking the Emergency brake  Connection Spot  sy RED   Normally  Key Switch OFF    12V  YELLOW   IG1  Key Switch ON  12V With the key switch ON  but not the engine  pull      Earth up to cut voltage and push down to engage   12V  er BLUE   ACC or IG2  12V power     ORANGE   q     Extra wire  BLACK   Body Earth Pull up a Push down  X not used under normal BROWN   Emergency Brake Switch   l y    conditions  ORANGE    Extra wire  ov    0 12V    0           REFERENCE  How to use the cut connectors    Method 1 Connecting a new wire to the middle of another wire  Method 2 Connecting two wires at their ends  X Use a crushing tool to press the cut connector  if  you do not have such a tool  use pliers or such to    1    y Peel off about 10mm of the vinyl cover   3 ae Twist the uncovered 1  7 fo  Peel off about 10mm of the vinyl covers fold and crush the connector together for a se      SS        at connection  wires  at the end of the wires to be connected  cure contact     2 h    y Peel off about 10mm of the vinyl cover   4 Close tightly with 2 Twist the uncovered 3 Close tightly with X After covering  make sure to insulate properly      at the
7. ot the  tape temporarily losses adhesiveness so no strong pressure should be applied       Be careful to turn off power switch of timer before locking the steering wheel   Using the timer with the lock on could be dangerous  if the car begins to  move       To ensure that no accidents occur while others are using your car  be sure to  urn off the power switch of the timer       Especially do not use if small children may be left alone in car while parked       Installing or using    TURBO TIMER    in places where ventilation is poor may re   sult in an to humans due to vehicle exhaust emission poisoning or fire      During installation be sure to remove the minus cable from the battery so as  o prevent fire and damage resulting from the shorting of circuits  etc         Please be careful that the cable dose not get crushed by the seat rail or car  door steel plate  nor cut by any sharp steel plate as this may cause a poor  connection or an electric short leading to fire or other danger       Because  it is very dangerous if  while in use  the product falls off and inter   eres with braking  please securely fasten it to a stable place       it is very dangerous to pull tangled wires by force or allow tangled wires to in       Make sure to replace all screws and parts that were removed during installation  to their original place                  erfere with driving  So  please be sure to store bundle away all wires with Please check the contents of the package  ape  etc      O
8. perating or checking the display during driving may cause an accident   please use with the utmost consideration for safety  SZ a       Main Unit Double sided Tape Cut Connectors X 1 User s Guide    Ultra Compact Design              g  Easy to Install  Simplified  Low cost Turbo Timer g   lt   a  1  Auto Mode 2  Manual Mode 3  Heating Mode 3  3  Auto setting of idling time in ac  Idling Time can be set in 10 second Heating Time can be set in 10 second    cordance to running time  increments from 0 seconds to 9 increments from 10 minutes to 19 min  50   see right figure  minutes  50 seconds  utes  50 seconds  Driving Time  min           BASIC WIRING       r         For safety purposes always wire to the emergency brake   Be sure to check all unit operations before installing   For safety  A NOTE purposes disconnect the    terminal of the battery while installing    When checking the connection  be sure to reconnect the     terminal   If for some reason it is impossible to connect to the emergency brake make sure to earth the BROWN wire     Special Harness for your Connecting the Wires  type of car model                                                                                            Key Cylinder caedesv ead When wiring use a special harness for your type of car model   Another company   s    WA   product may be used    D    Disconnect the harness of the key cylinder and between 2 cords connect the special harness     Connect the 3 pin coupler cable of the special har
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
M31e1 Engine Electrical 1-18  Catalogue Février 2013 Autographes & manuscrits  SQL*Plus Quick Reference    HANDSON OPTICS TRAINNING COURSE KIT of INTRODUCTION  EDITRAN/T  the great outdoors by Minka Lavery 72427-212 Instructions / Assembly  DIEU est "communication"  Samsung MM-ZL7 Наръчник за потребителя  Viking Refrigerator F20725A User's Manual    Copyright © All rights reserved. 
   Failed to retrieve file