User Manual / Parts List
Contents
1. ucts returned freight prepaid to Patron Products or such other location as Patron Products may designate Returned products must be packaged carefully and Patron Products shall not be responsible for damage in transit When returning parts the owner must provide the model number of the product and the nature of dif ficulty being experienced This warranty does not oblige Patron Products to bear the cost of labour in replac ing any assembly unit or component or part thereof nor does the company assume any liability for secondary charges expenses of removal or installing freight or damages There will be charges rendered for product repair after our warranty period has expired Proof of purchase including date must accompany request for in warranty service RENTQUIP USAINC 1 800 818 1199 WWW PATRONPRODUCTS COM patron E3 PRODUCT MANUAL OPERATION REVIEW AND UNDERSTAND ALL WARNINGS IN THIS MANUAL THEY ARE ESSENTIAL FOR SAFE USE OF THE HEATER Grounding pin FOLLOW ALL LOCAL CODES This heater is for use on 240 volts The cord has a plug as show in the figure The type of outlet is a 240 volt grounding outlet When properly installed it provides a ground connection through the cord to the heater to protect the operator from electric shock TO START HEATING 1 Place the heater on a stable and level surface Make sure that no explosive or combustible fumes or dust are present MINIMUM CLEARANCES FROM COMBUSTABLE MATERIAL2. S OUTLET 6 feet SIDES 1 foot TOP 2 feet REAR 2 feet FLOOR COMBUSTABLE 2 Connect power cord of heater into 240 V 60 Hz power source See paragraph Technical specifications in this manual for correct amperage rating 3 Set the room thermostat from heat off position to a temperature above the ambient room temperature by turning the knob Note The heater will start heating only if the thermostat calls for heat meaning that it is set to higher than prevailing ambient temperature 4 The heater will now operate automatically controlled by the thermostats TO STOP HEATING 1 Turn the room thermostat into position heat off 2 Disconnect the power supply plug NOTE THE HEATER IS EQUIPPED WITH AN OVERHEAT LIMIT SWITCH WHICH MAY CAUSE THE HEATER TO STOP CHECK AND REMOVE THE CAUSE FOR OVERHEATING BEFORE RESTARTING RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM p lcon E3 PRODUCT MANUAL MAINTENANCE WARNING NEVER SERVICE THE HEATER WHILE IT IS PLUGGED IN RUNNING OR HOT SEVERE BODILY INJURE OR ELECTRIC SHOCK MAY OCCUR ONLY GUALIFIED PERSONS ARE ALLOWED TO OPEN HEATER FOR SERVICE NO USER SERVICE ABLE PARTS INSIDE e Keep heater clean Use pressurized air to blow fan blades clean Note Use moderate pressure to avoid damage to fan blades e Inspect heater before and after each use e The fan motor is sealed and has permanently lubricated bearings STORAGE When not in use
3. from traffic area and where it will not be tripped over 8 To disconnect heater turn controls to off then remove plug from outlet 9 Connect to properly grounded outlets only 10 Do nat insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an elec tric shock or fire or damage the heater 11 To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft surfaces where openings may become blocked 12 A heater has hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored 13 Do not point to flammable materials 14 Use heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 15 Always plug heaters directly into a wall outlet receptacle Never use with an extension cord or relocatable power tap outlet power strip 16 SAVE THESE INSTRUCTIONS RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM patron E3 PRODUCT MANUAL GENERAL INFORMATION FOR USER Patron electric heaters are designed for professional use The heat is generated in sealed heating elements inside the inner mantle of the heater Heated air is then dis tributed by an electric motor driven fan blowing air through the heater Although effectively cooled by the fan the heating elements have high surface temperatures That is why com bu
4. palcon E3 ELECTRIC FAN HEATER PRODUCT MANUAL IMPORTANT READ AND UNDERSTAND THIS MANUAL BEFORE ASSEM BLING STARTING OR SERVICING THE HEATER IMPROPER USE OF HEATER CAN CAUSE SERIOUS INJURY KEEP THIS MANUAL FOR FUTURE REFERENCE FOR PROFESSIONAL USE ONLY OCTOBER 2014 REVISION RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM Pa n E3 PRODUCT MANUAL IMPORTANT INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS HEATER 1 This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Use handle when moving this heater Keep combustible materials at least 6 feet 2 meter from the front of the heater and keep them away from sides and rear 2 Extreme caution is necessary when the heater is used near children or invalids and whenever the heater is left unattended 3 Always unplug the heater when not in use 4 Do not operate any heater with a damaged cord or plug or after the heater malfunctions has been dropped or damaged in any manner Return heater to authorized service facility for examination electrical or mechanical adjustment or repair 5 Do not expose to rain water spray or dripping water 6 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate the heater where it may fall into a bathtub or other liquid container 7 Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away
5. stible materials must be kept at a safe distance from the heater and care must be taken that no combustible particles enter the heater with the air sucked in by the fan Keep the heater clean of dust at any time Dust may cause fire when heated Make sure that the fan blades may rotate unobstructed at all times Do not block air intakes or exhaust in any manner LIMITED WARRANTY PATRON heater products are professional construction heaters They are warranted for twenty four 24 months from original date of purchase The warranty does not cover products modified outside our factory damage or failure caused by acts of God abuse misuse use on other than rated voltage abnormal usage faulty or improper installation failure to provide recommended maintenance or any repairs other than those provided by an authorized PATRON service THERE ARE NO OBLIGATIONS OR LIABILITIES ON THE PART OF PATRON PRODUCTS INC FOR CON SEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER INDIRECT DAMAGES WITH RESPECT TO LOSS OF PROPERTY REVENUES OR PROFIT OR COST OF REMOVAL INSTALLATION OR REINSTALLATION THIS WARRANTY CONSTITUTES THE EXCLUSIVE REMEDY OF ANY PURCHASER OF EQUIPMENT SOLD BY THE MANUFACTURER AND ITS DEALERS AND DISTRIBUTORS AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED During the warranty period Patron Products will at its sole option repair or replace any defective parts or prod
6. the heater must be disconnected from power source cleaned of dust and stored in a dry place The power supply cord should be loosely wound around the handle of the heater TECHNICAL SPECIFICATIONS POWERCORD SXIGAWG PLUG NEMAG ISP 32 100 F 0 40 C RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM p lcon E3 PRODUCT MANUAL SPARE PARTS DIAGRAM PATRON E3 O 6 21200 14104 8 9 36910 12 13 20405 RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM patron E3 PRODUCT MANUAL WIRING DIAGRAM X1 3 R 42800 Heating Element 36701 Terminal Block Grounding Lug 30320 Power Cord 8 Plug RENTQUIP USA INC 1 800 818 1199 WWW PATRONPRODUCTS COM PATRON PRODUCTS A DIVISION OF RENTQUIP 1 800 818 1199 www patronproducts com
Download Pdf Manuals
Related Search