iQ2000™ User Manual
Contents
1. stow and slide each caster into the wheel stow housing Installing casters Unit must be secured to a forklift please refer to Item 4 Re move each caster and retaining pin from the wheel stow housing slide each caster into it s shaft and secure with a retaining pin Lock each caster prior to lowering unit from forklift to ensure that unit will remain stationary on surface 4 Prepare for Transport Moving and lifting unit by forklift Verify that the unit is not plugged into power source main door and dust bucket must be secure and cast ers locked Align forklift with fork tubes on the base of the unit precede forward until fork is securely inserted in tubes Lift unit to an adequate height in order to remove casters Unit can now moved to the desired location If unit is being trans ported tie down unit securely to a fixed position 5 Power On The on off switch is located on the side panel of the unit If the unit does not power on or shuts down after prolonged use in high temperature environ ments the thermal overload protection circuit may have become activated If so please wait 10 minutes before powering on again 6 Shaking Operation This unit is equipped with a shaking mechanism to clear the filter element of dust for optimum suction Before and during use 30 60 min as needed peri odically power off the unit the manual shaking handle should be moved vigorously up and down ten times power on unit OPERAT2. 01 Enclosure Top TQ2 P002 Main Door TQ2 P003 Dust Tray TQ2 P004 Fork Tube Base TQ2 P005 Dust Tray Gasket TQ2 P006 Filter Element Assembly IQ2 P007 Manual Shaking Handle IQ2 P008 Main Door Gasket IQ2 P009 Door Knob IQ2 P010 Grab Bar IQ2 P013 Auxiliary Cap O N AWD WT BR WW N PARTS LIST iQ MOTOR OPTIONS IQ 2003S IQ 2003S PART DESCRIPTIONS TQ3S P002 Fan 13 1 2 X 2 1 2 CW IQ3S P003 Fan Housing with Motor Plate IQ3S P004 Manual Motor Starter with Adjustable Overload Relay IQ3S P005 3 Wire Power Supply IQ 2013G IQ 2013G PART DESCRIPTIONS IQ13G P001 13 HP Gas Honda GXV390 Motor IQ13G P002 Throttle Control IQ13G P003 Off On Switch IQ13G P004 Fuel Line IQ13G P007 12V Battery IQ13G P008 Throttle Mount Plate IQ13G P009 Fuel Tank IQ13G P010 Fan 13 1 2 X 5 CW IQ13G P011 Fan Housing with Motor Plate IQ13G P012 Motor Push Start Button IQ13G P013 Battery Cable For Gas powered units refer to Honda Operators Manual for parts information motor servicing and operation IQ 2007T IQ 2007T PART DESCRIPTIONS TQ7T POO1 7 5 HP 460V Three Phase Motor IQ7T P002 Fan 13 1 2 X 5 CW IQ7T PO03 Fan Housing with Motor Plate IQ7T PO004 Manual Motor Starter with Adjustable Overload Relay IQ7T POO5S 4 Wire Power Supply IMPORTANT PRECAUTIONS It is the owner s responsibility to inform all users regarding the operating and safety precautions o
3. ING INSTRUCTIONS 7 Emptying the Dust Drawer The dust drawer must be emptied of debris on a regular basis First turn unit off and unplug from power source or lock out Rotate the dust drawer release lever clockwise one quarter turn lower and release Gently Slide the drawer forward and remove the plastic liner if applicable and replace with a new plastic liner Reverse these steps for reinstallation Verify that the drawer is properly positioned on reinstallation and the gasket has formed an adequate seal Failure to do this may cause a vacuum leak and gasket damage MAINTENANCE ano m D Changing Filters Filter tubes are designed to provide a long service life Howev er depending upon usage and the kind of materials vacuumed filters may need re placement every one to three years Replace filter tubes as follows Unplug unit from power source Vigorously move the manual shaking handle up and down ten times Open main door by turning the two door knobs counterclockwise Inside the main enclosure locate and remove the hitch pin clip the hitch pin clip attaches the arm of the manual shaking handle to the filter hanger assembly Pull the manual shaking handle outward to release the filter hanger assembly Remove all filter tubes from the metal filter housing plate by firmly squeezing and pulling in an upward motion the cuff ring the cuff ring is located at the lower end of each filter tube of each filter t
4. POWER TOOLS Built with You in Mind USER S MANUAL Model iQ 2000 Series Dust Collector with manual shaker 7 P i Vly AEROS aN Mtge eee RA WARNING Read all the following safety and operating instructions prior to using this unit Not ob serving this information can result in electrical shock serious physical injury or damage to equipment Personal Protective Equipment Respirator Safety Glasses Ear Plugs etc Should Be worn at all time when Operating or Servicing The Dust Collection Vacuum and Related Equipment For Gas powered units refer to Honda Operators Manual for motor servicing and operation Specifications Input Voltage 220 Single 480 Three Gas Powered VAC Phase Phase Honda GXV160 Power Consumption 3 HP 7 5 HP 13 HP Amperage A 15 N A Power Cable Length 10 Ft 10 Ft N A Fan Wheel 1312 x 212 1312 x 5 1312 x 5 Diameter x Width Weight LB 400 430 400 Max Air Flow CFM Max Static Pressure INCH H20 Filter Area SQ FT 144 Polyester 144 Polyester 144 Polyester Noise Level dB A 83 85 83 Hose Inlet Diameter 1 4 2 6 1 4 2 6 1 4 2 6 INCH Size W x Lx H 35 x 35 x 64 35 x 35 x 64 35 x 35 x 64 Dust Capacity 1 5 1 5 1 5 Cubic Ft For Gas powered units refer to Honda Operators Manual for motor servicing and operation PARTS LIST Model iQ 2000 ITEM NO IQ 2000 PART DESCRIPTION TQ2 P0
5. f this unit 1 2 11 12 13 Be sure that the unit is disconnected from the power source prior to any service cleaning or maintenance Grounding Unit must be grounded Verify that the green wire in the power cable iS properly connected to a secure earth ground Power Hook up The unit is designed to be operated from either a single phase or three phase power source depending on the model When an extension cord is needed the extension cord must be of the same or larger gauge to prevent loss of power or overheating of the cable Overload Circuit Breaker Make sure that the overload circuit breaker is set to proper amperage which maybe 15A or 7A depending on the model Static Shock Static shock is common in areas with relatively low humidity and is not an indicator that the unit is performing improperly Dry Pick up Do not vacuum toxic combustible or other hazardous materials such as asbestos arsenic barium beryllium lead or pesticides Do not vacuum weld ing fumes burning cigarettes ashes matches or other similar materials Never operate the unit in the presence of flammable vapors aerosol products or near the spraying of flammable liquids i e paints and oils Do not operate the unit without the filter tubes in place Lock option casters in place when unit is in operation or storage Dust bucket release handle must be in upright position prior to operation of the unit Never leave the unit unattended
6. ube Use care during this operation in order to reduce any airborne dust that may be released When all filter tubes have been released from the metal filter housing plate pull the entire filter hanger assembly forward Remove and set aside all hitch pin clips from the filter hanger assembly Slide all filters tubes off the filter hanger assembly and properly dispose of all used filter tubes Replace with new filter tubes Reassemble by reversing these steps Lubrication No lubrication is necessary However certain parts of the vacuum as sembly are subject to wear and should be replaced as necessary depending upon operating conditions 4 Caution During reassembly verify that the cuff ring for each filter tube is snugly positioned in the metal filter housing plate Do not use the unit if the cuff rings are not snugly positioned in the metal filter housing plate LL LIMITED WARRANTY IQ Power Tools warrants this equipment to the original owner against defective materials or workmanship for a period of one year from the date of purchase IQ Power Tools responsibility under this warranty is limited to the repair or replacement of defective parts and reserves the right to determine whether the failure is due to defective material work manship or other causes Failures caused by alteration or misuse are not covered by the warranty All warranty repairs must be done by IQ Power Tools or an authorized service representative An
7. while it is powered on Do not put hair clothing or body parts in front of the unit s hoses or suction inlets while the unit is powered on Transport operate and store the unit on level surfaces to ensure the unit will re main stationary OPERATING INSTRUCTIONS il Power Hook up Electrical power hook up must be performed by a li censed electrician in accordance with the applicable electrical codes Con firm that motor rotation is in the direc tion of the arrow inscribed on the unit Inlet Hose Duct Installation At tach the proper diameter hose to the corresponding suction inlets using con ventional hose clamps Auxiliary inlet must be covered with cap when not in use to ensure proper suction Hoses and clamps should be checked regular ly for adjustments and signs of wear OPERATING INSTRUCTIONS 3 Operating of Casters Optional To lock casters Pull caster hand lever in up right position perform this function for each caster This will ensure unit will remain Stationary while in use or being stored To unlock casters push caster hand lever in downward position Each caster must be unlocked in order to relocate the unit Removing casters First lock all casters Lift unit with forklift please refer to Item 4 to an adequate height Provide support beneath the caster and remove re taining pin in from shaft Slide each caster out of it s shaft Place each retaining pin around the corresponding wheel
8. y repair to the equipment other than by these authorized facilities voids this warranty These rights under this warranty are limited to the original owner and may not be transferred to subse quent owners POWER TOOLS P O Box 7449 Moreno Valley CA 92552 Tel 888 274 7744 www iqpowertools com
Download Pdf Manuals
Related Search