AquaTRAM 360 Pool Lift User`s Manual
Contents
1. 13 ooo SEAT ASSEMBLY P N 11214 QUICK RELEASE ADJUSTABLE P N 11213 STEP 6 INSTALL THE FOOTREST Locate the FOOTREST ASSEMBLY and install it on the seat as shown above The QUICK RELEASE PIN is attached to the SEAT ASSEMBLY with a lanyard cable Pull out the pin and slide the FOOTREST ASSEMBLY into the slot and line up one of the holes on the FOOTREST TUBE with the hole for the pin Push the pin back into the hole and through the hole in the FOOTREST TUBE to hold the FOOTREST ASSEMBLY in the desired position To re adjust the FOOTREST simply pull out the pin and select a new hole on the FOOTREST TUBE 14 24V BATTERY P N 11211 P N 11275 HANDSET CONTROL P N 11274 STEP 7 INSTALL 24V BATTERY 8 HANDSET shown below THE LIFT WILL NOT FUNCTION IF THE HANDSET PLUG IS NOT FULLY SEATED OR IF THE BATTERY IS NOT PROPERLY ALIGNED NOT SEATED SEATED 15 Locate the 24V Battery the Battery Charging unit and the Handset Control Charge the battery for 24 hours see page 16 Charging the Battery then install it on the bracket above the Control Box as shown above and in the photo to the left Plug the Handset Control into the Control Box as shown above and in the photo to the left Press firmly to make sure the plug is fully seated as LIFT OPERATION Before operating the lift for the first time the user or operator should become familiar with the Handset Control and2. Pentair Water Commercial Pool and Aquatics AQUATRAM 360 POOL LIFT USER MANUAL 4 N WARNING IMPORTANT SAFETV INSTRUCTIONS 1 WARNING TO REDUCE RISK OF INJURY DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT 2 WARNING DO NOT PERMIT CHILDREN TO OPERATE OR USE THIS PRODUCT 3 SAVE A COPY OF THESE INSTRUCTIONS 2011 Pentair Water Pool and Spa Inc All rights reserved 1620 Hawkins Ave Sanford NC 27330 919 566 8000 10951 West Los Angeles Ave Moorpark CA 93021 805 553 5000 AqualTRAM and Pentair Water Commercial Pool and Spa are trademarks and or registered trademarks of Pentair Water Pool and Spa Inc and or its affiliated companies in the United States and or other countries Unless noted names and brands of others that may be used in this document are not used to indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair Water Pool and Spa Inc Those names and brands may be the trademarks or registered trademarks of those parties or others P N 11269 Rev A 04 18 11 AQUATRAM 360 POOL LIFT 500 LB 227 kg MAXIMUM CAPACITY MANDATORY LEAVE THIS MANUAL WITH LIFT OWNER READ CAREFULLY Check entire box and inside all packing materials for parts Before beginning assembly read the instructions and identify parts using the figures and parts listed in this document It is critical that all parts be carefully inspected by the installer prior to
3. CHARGING THE BATTERY Before using any of the AquaTRAM Series Lifts for the first time the 24V Battery must be fully charged This will take about 24 hours on the charger It is also recommended that the battery be fully charged before each use The battery can be left on the Charging Unit overnight or whenever the lift is not in use DO NOT LEAVE THE BATTERY ON THE LIFT To recharge the battery simply grip the top of the battery and depress the clip on the back of the battery This will unclip the battery from the control box bracket The battery can then be clipped into the wall mount charger When the charger is plugged in the green ON light will illuminate When the battery is correctly mounted to the charger the orange CHARGE light will illuminate When the battery is fully charged the CHARGE light will GO OFF and the battery is ready to use WALL MOUNT CHARGER SAFETY amp MAINTENANCE INSTRUCTIONS DO NOT PLAY ON OR AROUND THIS LIFT Check the AquaTRAM Series Pool Lifts before each use to assure there are no worn parts and that all hardware is properly tightened If there are any worn parts replace them BEFORE using the AguaTRAM Series Pool Lifts You can call our customer service at 1 888 687 3552 to order any parts Pentair Water Commercial Pool and Aquatics lifts shall be grounded per local codes Atleast ONCE A WEEK the AquaTRAM Series Pool Lifts must be cleaned with fresh water Do not spray the AquaTRAM S
4. installation to ensure that no damage occurred in transit and that a damaged part is not used If any damage occurred in transit Pentair Water Commercial Pool and Aquatics Pentair must be notified within three days of receipt of unit Proper installation cannot be overstressed as an improper installation voids Pentair s warranty and may affect the safety of the user WARNING IMPORTANT SAFETY INSTRUCTIONS 1 READ AND FOLLOW ALL INSTRUCTIONS LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT IS INSTALLED AND OPERATED PROPERLY ACCORDING TO THESE INSTRUCTIONS WARNING TO REDUCE RISK OF INJURY DO NOT PERMIT CHILDREN TO USE OR OPERATE THIS PRODUCT WARNING DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT WARNING NEVER APPLY DIRECT WATER PRESSURE TO ELECTRONIC COMPONENTS NEVER OPERATE THIS LIFT UNDER LOAD WITH NO WATER DRY POOL SAVE A COPY OF THESE INSTRUCTIONS 9 oS MAKE SURE THE AREA AROUND THE LIFT IS CLEAR BEFORE OPERATING NEVER OPERATE THE LIFT WITH ANY PERSON WITHIN THE OPERATING RANGE OF THE LIFT INCLUDING ON THE DECK OR IN THE WATER NEVER MOVE THE LIFT DOWN WHILE OVER THE DECK IF THE LIFT COMES INTO CONTACT WITH THE DECK OR A WALL RELEASE THE BUTTON IMMEDIATELY OR PRESS THE EMERGENCY STOP BUTTON DO NOT ALLOW CHILDREN TO OPERATE THE LIFT WITHOUT SUPERVISION CHECK ALL NUTS AND BOLTS FOR TIGHTNESS AND FOR WORN PARTS BEFORE EACH USE PAGE 10 11 12 13 14 15 16 17 18 19 20 2
5. S S 5 3 8 FLAT WASHER S S 1 1 9 16 WRENCH OR SOCKET 2 3 8 NYLOCK NUT S S 1 3 4 WRENCH OR SOCKET 1 A ALLEN WRENCH SET UNPACKING THE SHIPPING CONTAINER When you receive your new AquaTRAM 360 lift check your shipment carefully Locate all main components and hardware listed above The tools listed will be needed to install and assemble the lift PUT THE 24V BATTERY ON THE CHARGER AS SOON AS POSSIBLE The battery will need to be charged for 24 hours before first use 122 cm ADA REQUIRED CLEAR DECK SPACE DECK 30 5 cm 12 40 6 cm 16 LIFT LOCATION ADA GUIDELINES Before installing the AquaTRAM 360 lift it will be necessary to select a location for the anchor Because of its versatility the AquaTRAM 360 lift can be installed in a wide variety of locations but the owner installer should be aware of the requirements of the Americans with Disabilities Act ADA with concern to lift installations The diagram above shows an example of an ADA compliant installation which incorporates the following ADA rules in order to be compliant e SEAT LOCATION In the raised position the centerline of the seat shall be located over the deck and 16 inches 406mm minimum from the edge of the pool pool wall The deck surface between the centerline of the seat and the pool edge shall have a slope not greater than 1 48 e CLEAR DECK SPACE On the side of the seat opposite the water a clear deck
6. compressed air Proper hole cleaning is essential If the hole is wet dry it out as much as possible A heat gun may be helpful in drying out the hole 4 Mask the top of the anchor so that no epoxy gets inside the anchor 5 Place the anchor in the hole and dry fit it first to make sure the anchor will be flush and plumb with the deck when installed Adjust the hole as needed 6 Install the epoxy into the dispenser and follow manufacturers instructions to ensure that the epoxy is properly mixed and applied USE ONLY THE RECOMMENDED EPOXY AND ALWAYS FOLLOW THE INSTRUCTIONS SO THAT FULL STRENGTH IS ACHIEVED 7 Inject epoxy adhesive starting at the bottom until the hole is 1 3 to 1 2 full 8 Install the anchor into the epoxy and push down until it is flush with the deck surface Clean off excess epoxy Adjust the anchor to make sure it is flush and plumb with the deck surface 9 Let the epoxy cure for at least 24 hours before installing the lift or where applicable according to the manufacturers instructions Use HILTI HIT HY 150 adhesive anchor or SIMPSON ET22 StrongTie anchor adhesive or equivalent NOTE BOND GROUND THE ANCHOR PER LOCAL ELECTRICAL CODE ANCHOR INSTALLATION NEW CONSTRUCTION For new construction a footing should be poured according to the diagram below Again make sure the anchor is installed flush and plumb with the deck surface and bond it to the rebar grid Again the footing should have the follo
7. its functions The figure to the left gives a quick explanation of the four buttons and their function For example to move the m lift UP press the top left button with the A HANDSET CONTROL symbol and hold it down until the lift has reached MOVE He MOVE its desired height and then release the button UP gt DOWN The other buttons work in a similar fashion In all cases releasing the button will cause the lift to stop moving e TO MOVE UP PRESS AND HOLD THE A BUTTON TO STOP MOVING UP RELEASE THE BUTTON TO MOVE DOWN PRESS AND HOLD THE VY BUTTON TO STOP MOVING DOWN RELEASE THE BUTTON e TO MOVE LEFT PRESS AND HOLD THE 4 BUTTON TO STOP MOVING LEFT RELEASE THE BUTTON e TO MOVE RIGHT PRESS AND HOLD THE Y BUTTON TO STOP MOVING RIGHT RELEASE THE BUTTON ROTATE viz ROTATE LEFT RIGHT s ROTATE gH l1 Hi ROTATE El RIGHT d S Y v atv a F nto y EO WENT pim TASES Por ee ka teas USING THE EMERGENCY STOP BUTTON on the Control Box On the front side of the control box is a small recessed button marked emergency If you take a pen or pencil or other pointed object and depress the emergency button this will bypass the remote control or handset and stop the lift NOTE this function will only work if there is sufficient power in the battery the battery is properly attached to the control box and the control box must be operating properly
8. some brisk rubbing DO NOT USE POOL WATER TO CLEAN USE ONLY FRESH WATER If the lift is used DAILY make sure to wash the lift at the end of the day Wash the lift off using a mild soap and a soft cloth Make sure to pay special attention to weld points and crevices Do not use a bristled brush or steel wool to clean the lift Check that the lift is working properly and then place the battery on the charger lt is recommended that the battery be charged after every day of use If the lift is used WEEKLY follow the same steps as above Also be sure to check all of the contact points terminals for damage or corrosion If you notice corrosion gently clean the terminals To clean corrosion from the terminals use a q tip and some rubbing alcohol If the corrosion is particularly stubborn try using a 3M scotch brite pad but be careful not to damage the terminals Apply dielectric grease to the terminals after cleaning them This will help to prevent further corrosion Do not leave the battery on the lift Always store the battery on the charger whenever the lift is not being used If the lift is used MONTHLY follow the same steps as above Also check the nuts and bolts to make sure they are securely fastened this is always a good idea no matter how often or infrequently the lift is used Also make sure to store the battery on the charger and not on the lift Leaving the battery on the lift for extended periods will significantly shorten the battery s
9. workmanship for a period of five 5 years from the date of original purchase provided that Pentair receives prompt notice in writing of any claim and satisfactory proof thereof with the following exceptions All electrical components including the linear actuator shall have the following warranty coverage during the five 5 Year Limited Warranty periods Year 1 2 100 Coverage Year 3 60 Coverage Customer is responsible for 40 of replacement cost Year 4 50 Coverage Customer is responsible for 50 of replacement cost Year 5 40 Coverage Customer is responsible for 60 of replacement cost This warranty specifically excludes reimbursement for labor to remove repair replace or install the Lift or component part thereof and any return freight charges These warranties do not cover any damages due to accident misuse abuse negligence or failure to properly maintain any Lift or component part thereof or normal wear and tear from day to day operations In the event that any Lift or component part thereof are altered repaired or improperly installed or improperly used by anyone without the prior written approval by Pentair all warranties are void IMPORTANT AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFT CAPACITY 400 POUNDS FOR The AquaTram Lift 500 POUNDS for the AquaTram 360 Lift To initiate a warranty claim the owner of an AquaTram Lift must provide the place of purchase in writing with a full descri
10. 1 22 23 25 26 TABLE OF CONTENTS ASSEMBLY OVERVIEW LIFT LOCATION ADA GUIDELINES USA APPLICATION GUIDE ANCHOR INSTALLATION RETROFIT ANCHOR INSTALLATION NEW CONSTRUCTION STEP 1 LIFT ASSEMBLY STEP 2 INSTALL LIFTING ARM STEP 3 INSTALL CONTROL ARM STEP 4 INSTALL SEAT ARM STEP 5 INSTALL SEAT ASSEMBLY STEP 6 INSTALL FOOTREST STEP 7 INSTALL BATTERY 8 HANDSET CONTROL LIFT OPERATION CARE AND CLEANING TROUBLESHOOTING GUIDE PART LIST 8 EXPLODED VIEW SEAT ASSEMBLY PARTS LIST OPTIONS WARRANTY INFORMATION MAIN COMPONENTS 1 MAIN ASSEMBLY ASSEMBLY OVERVIEW 2 LIFTING ARM STEP 2 CONTROL ARM 3 CONTROL ARM STEP 3 4 SEAT ARM STEP 4 SEAT ARM 5 SEAT ASSEMBLY STEP 5 STEP 4 6 FOOTREST ASSY STEP 6 7 24V BATTERY PACK STEP 7 STEP 5 8 HANDSET CONTROL STEP 7 9 BATTERY CHARGER NOT SHOWN ASSEMBLY OVERVIEW STEP 1 INSTALL IN ANCHOR STEP 2 INSTALL LIFTING ARM STEP 3 INSTALL CONTROL ARM STEP 4 INSTALL SEAT ARM FOOTREST ASSEMBLY STEP 6 STEP 5 ADJUST SEAT HEIGHT STEP 6 INSTALL FOOTREST STEP 7 INSTALL BATTERY amp HANDSET CONTROL HARDWARE LIST TOOL LIST DESCRIPTION ANCHOR INSTALLATION 1 2 X 2 3 4 SHOULDER BOLT C SAW W DIAMOND BLADE S S 2 1 2 X 3 SHOULDER BOLT S S CHALK LINE 14 5 16 FLAT WASHER S S TORPEDO LEVEL 224 5 16 NYLOCK NUT S S A A 3 8 X 1 3 4 SHOULDER BOLT Im LIFT ASSEMBLY
11. 1 4 SHOULDER BOLT S S 3 8 16 X 1 3 4 SHOULDER BOLT S S 3 8 16 X 2 1 2 HEX BOLT S S 3 8 16 X 4 1 2 HEX BOLT S S 30 6 Y8 I6NYLOCKNUT SS 000 1 2 X 3 SHOULDER BOLT S S 32 8 12 X3 4 X 3 8 FLANGE BEARING BRONZE 33 8 1 2 X3 4 FLANGE BEARING BRONZE 3 8 X 1 2 X 3 8 FLANGE BEARING BRONZE 3 8 X 1 2 X 3 8 PLAIN BEARING BRONZE 1 1 4 X 1 3 4 X 2 PLAIN BEARING BRONZE 5 16 FLAT WASHER S S PARTS LIST ELECTRICAL HARDWARE PARTS LIST SEAT ASSEMBLY 6 FLAT WASHER SS A ILANYARDFORQRP 9 IISHEET METALSCREW SS 22 Options for AquaTRAM 360 Adjustable Head Rest P N 11254 Includes e Padded head rest mounted to adjustable bracket with mounting hardware Adjustable Chest Strap P N 11206 Includes e Adjustable hook and loop style chest strap and mounting hardware Pullout Leg Rest P N 11208 Includes e Pullout leg rest to be factory installed Cycle Attachment P N 11207 Includes e Pedal attachment and mounting hardware cannot be used on lifts equipped with Pullout Leg Rest 11208 e 90 up turned hand grips for better support Transport Cart P N 11253 Includes e Heavy Duty lifting cart e Boom guide e Base lifting plate 23 Spine Board Attachment P N 11260 Includes e Powder Coated Stainless Steel Spine Board boom attachment e 6 0 Spine Board e Optional Head Immobilizer P
12. ARM Locate the LIFTING ARM and the following hardware 1 1 2 x 2 3 4 SHOULDER BOLT 1 3 8 x 1 3 4 SHOULDER BOLT 1 5 16 FLAT WASHER 1 5 16 NYLOCK NUT 2 3 8 FLAT WASHER 1 3 8 NVLOCK NUT Remove the shipping strap and all packing from the LINEAR ACTUATOR Connect the LIFTING ARM between the MAST and the ELECTRIC LIFTING RAM as shown in the figure above Tighten NYLOCK NUTS 2 until snug as shown in PHOTO 2 DO NOT OVER TIGHTEN 10 3 8 3 8 FLAT WASHER L d CONTROL ARM MAIN ASSEMBLX STEP 3 INSTALL CONTROL ARM Locate the CONTROL ARM and the following hardware e 1 1 2 x 2 3 4 SHOULDER BOLT e 1 3 8 FLAT WASHER e 1 3 8 NYLOCK NUT Install the CONTROL ARM either end onto the MAST as shown in the figure above Tighten the NYLOCK NUT until snug as shown in PHOTO 3 DO NOT OVER TIGHTEN 11 1 2 X 3 SHOULDER BOLT CONTROL ARM 1 2 X 3 SHOULDER STANDARD SEAT ARM STEP 4 OR SPA SEAT ARM OR SLING SEAT ARM NOTE FOR APPLICATIONS WHICH USE MULTIPLE SEAT ARMS REMOVE NUTS amp BOLTS AND REPLACE ARM AS REQUIRED AS FLAT WASHER 3 8 NYLOCK NUT 3 8 FLAT WASHER 3 8 NYLOCK STEP 4 INSTALL SEAT ARM Locate the SEAT ARM and the following hardware e 2 1 2 x 3 SHOULDER BOLT e 2 3 8 FLAT WASHER e 2 3 8 NYLOCK NUT Install the SEAT ARM at the ends of the CONTROL ARM and LIFTING ARM as shown
13. FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED WHICH ARE HEREBY DISCLAIMED AND EXCLUDED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE LIFT OR COMPONENT PART THEREOFSHALL BE LIMITED TO REPAIR OR REPLACEMENT AT PENTAIR S DESIGNATED FACTORY LOCATION OR DULY APPOINTED DISTRIBUTOR OR SUCH OTHER LOCATION AT PENTAIR S SOLE OPTION IN NO EVENT SHALL PENTAIR S LIABILITY EXCEED THE ENTIRE AMOUNT PAID TO PENTAIR BY THE ORIGINAL PURCHASER FOR THE LIFT OR COMPONENT PART THEREOF IN NO EVENT SHALL PENTAIR BE LIABLE FOR ANY INCIDENTAL CONSEQUENTIAL SPECIAL INDIRECT PUNITIVE OR EXEMPLARY DAMAGES OR LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE Pentair Water Commercial Pool and Aquatics M A Division of Pentair Water Pool and Spa Inc 1620 Hawkins Ave Sanford NC 27330 1351 Route 55 LaGrangeville NY 12540 26 PENTAIR WATER POOL AND SPA INC 1620 Hawkins Ave Sanford NC 27330 10951 W Los Angeles Ave Moorpark CA 93021 Phone 800 831 7133 Fax 800 284 4151 P N 11269 Rev A 21
14. N 11261 4 OPTIONAL ZN HEAD IMMOBILIZER AND PADDED X VELCRO STRAPS FLIP DOWN CLAMPS ALLOW FOR QUICK RELEASE RE ATTACHMENT Gurney Attachment P N 11258 Includes e Powder Coated Stainless Steel Gurney boom attachment e Pool and Spa friendly PVC gurney with vinyl coated foam pad Gurney to have swing down side rails and five position reclining headrest Casters for gurney are also included Sling Arm Option P N 11255 Includes e Sling arm boom attachment e Sling Arm e Sling Chains e Sling Bars e Polyester Mesh Sling with 500lb capacity 24 Wheel Chair Attachment P N 11259 Includes e Wheel Chair boom attachment e 22 solid framed Stainless Steel Wheel Chair Wheel Chair attachment to be used ONLY with wheel chair provided Protective Cover P N 11257 25 AquaTram M AquaTram 360 Pentair Water T A a Swimming Pool Access Lift Commercial Pool and Aquatics A Division of Pentair Water Pool and Spa Inc FIVE 5 YEAR LIMITED WARRANTY AquaTram and AquaTram 360 Lift Lift have a Limited Lifetime Warranty on the frames not including the powder coat finish Pentair Water Pool and Spa Inc Pentair also warrants to the original end user purchaser that these Lifts when properly installed in accordance with assembly and installation instructions and properly used and maintained shall be free from defects in material and
15. NS The AquaTRAM 360 lift should be installed in a deck or footing with the following specifications 1 MINIMUM FOOTING SIZE 4 0 x 4 0 x 12 THICK 2 MINIMUM CONCRETE STRENGTH 3000 PSI 3 REINFORCEMENT 5 REBAR 10 ON CENTER O C To ensure adequacy of an existing pool deck a 4 0 square portion of the existing deck may be saw cut removed and replaced with a footing as specified above The new slab reinforcing shall be drilled and epoxied into the existing slab as shown on the next page If your deck or footing does not meet these requirements please call 1 800 831 7133 for recommendations The anchor should be bonded grounded per local electrical code For decks that meet these requirements follow these instructions to install your anchor TOOLS 8 MATERIALS REQUIRED CORE DRILL WIRE BRUSH 3 1 2 CORE DRILL BIT AIR NOZZLE amp PUMP COMP MARKING PEN HEAT GUN OPTIONAL EPOXY ANCHOR ADHESIVE MASKING TAPE 1 Select an anchor location using the diagram below and the ADA guidelines on page 4 Mark the center of the anchor location with a pen or marker 2 Using a 3 1 2 diameter core drill bit drill a 3 1 2 diameter hole at the anchor location Make sure to keep the bit square to the deck Drill straight down to a depth of at least 9 3 Remove plug and clean out the hole with a wire brush and then insert an air nozzle to the bottom of the hole and blow out the hole using a pump or
16. bing alcohol and a q tip and clean off the points After cleaning the contact points it is recommended to put some dielectric grease on the contact points terminals to help ensure good electrical contact and prevent corrosion Then reinstall the battery on top of the control box Make sure you hear a click which indicates that the battery is correctly seated The lift will not work if the battery is not seated correctly Silver tabs are the contact terminal points If the lift stops moving over the water and is stuck 4 Push the emergency button If the lift gets stuck out over the water use a pen or pencil tip and stick it into the emergency button on the front of the control box to retract the lift Note the lift will not retract if the battery is not fully charged or if the control box is not working The emergency button only overrides the remote in case it has gone bad If this does not retract the lift then chances are the remote is fine and you either have a problem with the battery the control box or the cords are damaged or not plugged in properly Use a pen or pencil tip to push in the small black circle located next to the word emergency on the front of the control box 20 6 1 AquaTram360MASTASSEMBLY 8 1 jAquafram360CONTROLARM 9 1 jAquafram360SEATARM 48 32 X 3 16 SETSCREW S S 1 4 20 X 1 FLAT HEAD CAPSCREW S S 22 8 1 4 20X 1 HEX BOLT S S 3 8 16 X 1
17. d on the unit Also note that when the battery is properly seated there should not be any gaps between the battery and the control box charger Not attached properly Note the white Properly Attached bracket is in front of silver clip which Note that the white bracket is behind the will not allow for an electrical silver clip Not allowing movement connection 19 If the battery is fully charged and the lift is not moving then 2 Check all cords Check that the cords are properly plugged in Start by unplugging the remote and the actuator cord from the control box Once these cords are removed check the ends for corrosion or damage Plug the remote cord back in by lining up the raised tab on the plug to the grooved line on the control box outlet Note that these cords require some force to plug them in fully You will know they a correctly inserted when you here a popping sound The cords will be recessed into the outlet If they are flush with the outside of the outlet they are not plugged in fully and the lift will not function Make sure you do this for both cords NOT inserted fully Fully inserted If you have checked all the cords and the lift still doesn t move 3 Check the contact points After you have fully charged the battery and checked the cords to make sure they are properly plugged in check to make sure the contact points are not corroded or bent If the contact points are corroded take some rub
18. eries Pool Lifts 24v battery unit directly with any pressure Wipe all surfaces clean with a damp non abrasive cloth When cleaning the AquaTRAM Series Pool Lifts use non abrasive soap and water Avoid harsh chemicals and disinfectants Always read the label instructions on any cleaner carefully before applying it to a surface The WARNING amp INTENDED USE labels on the AquaTRAM Series Pool Lifts must be maintained in readable fashion If they become unreadable or faded please replace the label immediately Replacement labels are available from Pentair Water Commercial Pool and Aquatics 1 800 831 7133 CARE OF YOUR LIFT Routine cleaning is an absolute necessity to ensure the integrity of the lift Note that the lift should not be stored in a pump room or in a storage room where pool chemicals are kept Storing the lift near pool chemicals may cause rusting and other damage to occur Your stainless steel lift is powder coated to protect the stainless steel from rusting Most rusting will occur at weld points crevices under gaskets rivets or bolt heads The choice of a proper cleaning product is up to the consumer and there are many to choose from Depending on the type of cleaning and the degree of contamination rusting some products are better than others For routine cleaning the products most recommended are gentle soaps or detergents or dilute mixtures of ammonia For stubborn spots and stains try using soft scrub with
19. in the figure above Tighten the NYLOCK NUTS until snug as shown in PHOTO 4 DO NOT OVER TIGHTEN NOTE MAKE SURE THE SEAT IS FACING AWAY FROM THE MAIN ASSEMBLY NOTE FOR APPLICATIONS THAT UTILIZE MULTIPLE SEAT ARMS SUCH AS FOR A SLING SEAT OR THE SPA SEAT ARM USE THIS STEP TO REMOVE AND REPLACE THE SEAT ARM 12 3 8 NYLOCK NUT 38 FLAT WASHER SEAT ARM HOLES 4 INTERVALS ALLOW FOR ADJUSTMENT OVER 16 RANGE SEAT ASSEMBLY ADJUSTED TO 1 A LOWEST POSITION m SEAT WILL ARRIVE m AT HIGHEST POSITION MAIN ASSEMBLY P 3187 X 1 34 HEX BOLT 318 FLAT WASHER 3 8 X 4 HEX BOLT SS FLAT WASHER STEP 5 ADJUST THE SEAT POSITION The SEAT ASSEMBLY will arrive attached to the SEAT ARM adjusted to its highest position To adjust the SEAT ASSEMBLY to a lower position remove the hardware as shown above Slide the SEAT ASSEMBLY to its desired position in 4 increments and reinstall the hardware The total adjustment range is 16 DO NOT ATTACH THE SEAT ASSEMBLY ANY LOWER THAN THIS ALWAYS USE THE TWO 2 SUPPLIED HEX BOLTS TO ATTACH THE SEAT ASSEMBLY TO THE SEAT ARM NOTE For most applications such as pools with a flat deck the seat will be installed in its lowest position For applications where a wall or curb must be cleared the seat should be installed in a higher position In its highest position the seat will clear a 30 762mm high wall
20. lifespan If the lift is being STORED for an extended period of time follow all of the steps above Check for rusting at all crevice and weld points If you notice rusting spray some WD 40 on the affected area and take a 3M scotch brite pad and rub briskly Afterwards be sure to wash and rinse the lift again with soap and water When storing the lift make sure it is in a dry area and covered DO NOT STORE in or around pool chemicals 18 TROUBLESHOOTING GUIDE Before troubleshooting make sure the battery is fully charged If the lift doesn t move when the handset button is pressed When you can t get the lift to move check the following things 1 Make sure the battery is fully charged A Before charging the battery first make sure the green light on the front of the charger is illuminated this means that the charger is on Then check to make sure the silver contact points on the battery and charger are not damaged or corroded and that they are clean Then place the battery on the charger and look for the orange charge light to illuminate on the front of the charger When the orange light goes off the battery is fully charged The top green light will always be illuminated indicating that it has power When charging the battery the bottom orange light will illuminate until fully charged C When the battery is correctly installed on the charger or control box you should hear a click indicating the battery is properly seate
21. ption of the Lift its serial number the dates of purchase and installation and the exact nature of the claim Within thirty 30 days after receipt of a written warranty claim by Pentair and barring any unforeseen delays the place of purchase will be notified of Pentair s decision regarding the claim If requested by Pentair any Lift or component part thereof must be returned freight prepaid to Pentair s designated factory location or duly appointed distributor for inspection and or repair or replacement Pentair will at its option refund the purchase price or repair or replace the Lift or component part thereof and deliver the repaired Lift or component part thereof or replacement to the buyer of the Lift freight prepaid to the destination provided for in the original order Lift or component part thereof returned to Pentair for which Pentair provides replacement under this limited warranty shall become the sole property of Pentair A new warranty period shall NOT be established for the repaired or replaced Lift or component part thereof Such Lift or component part thereof shall remain under warranty only for the remainder of the original warranty period on the original Lift purchased This written limited warranty constitutes the final complete and exclusive statement of warranty terms No person or organization is authorized to make any other specific or implied warranties or representations on behalf of Pentair THE WARRANTIES SET
22. space shall be provided parallel with the seat The space shall be 36 inches 914mm wide minimum and shall extend forward 48 inches 1219mm from a line located 12 inches 805mm behind the rear edge of the seat The clear deck space shall have a slope not greater than 1 48 AquaTram 360 LIFT ATPOOL LEVEL Aqualram 360 LIFT IN MULII LEVEL di APPLICATION Aqualram 360 LIFT DECK LEVEL LOADS AT DECK LEVEL Aqualram 360 LIFT AT SPA LEVEL Aqualram 360 LIFT AquaTram 360 LIFT AquaTram 360 LIFT LOADING POSITION IN POOL IN SPA AQUATRAM 360 APPLICATION GUIDE The AquaTRAM 360 lift has been designed for optimal flexibility offering the user a wide range of options for lift placement Shown above the AquaTRAM 360 lift is ideal for applications where access to multiple levels elevations is required The AquaTRAM 360 lifts adjustable seat arm makes such applications easily implemented as in this case where the seat has been installed in one of the middle height positions With the seat in its highest position the AquaTRAM 360 lift will clear a 30 762mm high spa or pool wall Also because the AquaTRAM 360 lift rotates in either direction a full 360 it can be installed close to a wall with the wall on either side NOTE IT IS RECOMMENDED THAT ANY WALL IN CLOSE PROXIMITY TO THE LIFT BE PADDED TO PREVENT DAMAGE TO THE LIFT OR INJURY TO THE USER SHOULD THE LIFT BE ACCIDENTALLY OVER ROTATED ANCHOR INSTALLATION RETROFIT INSTRUCTIO
23. wing specifications 4 MINIMUM FOOTING SIZE 4 0 x 4 0 x 12 THICK 5 MINIMUM CONCRETE STRENGTH 3000 PSI 6 REINFORCEMENT 5 REBAR 10 ON CENTER O C 4 O LLI MAX ANCHOE 3000 FSI MIN CONCRETE POOL WALL W RS REBAR 10 O C i4 REBAR ic 18 O C 4 MIN EMBED NOTE If the SLING OPTION is to be used the maximum setback distance is 24 from the pool wall to the anchor NOTE BOND GROUND THE ANCHOR PER LOCAL ELECTRICAL CODE INSTALLATION 8 ASSEMBLY INSTRUCTIONS MAIN ASSEMBLY LOCKING PIN LOCKING SLOT ANCHOR DECK STEP 1 INSERT MAIN ASSEMBLY INTO ANCHOR Locate the AquaTRAM 360 MAIN ASSEMBLY and lift it from the shipping container WARNING NEVER LIFT THE MAIN ASSEMBLY USING THE ELECTRIC LIFTING RAM AS A HANDLE LIFT THE ASSEMBLY FROM THE ENDS USE AT LEAST 2 PEOPLE TO LIFT Insert the 2 50mm POST of the AquaTRAM 360 MAIN ASSEMBLY into the deck anchor Align the LOCKING PIN with the LOCKING SLOT in the anchor and ease the MAIN ASSEMBLY down until it rests on the POOL SPA DECK SURFACE WARNING MAKE SURE THE LOCKING PIN SLIDES INTO THE LOCKING SLOT OF THE ANCHOR AND THAT THE MAIN ASSEMBLY SITS FLUSH WITH THE DECK SURFACE 1 27 X 2 3 4 3 8 FLAT WASHER SHOULDER 38 NYLOCK NUT 5 16 NYLOCK NUT 5 16 FLAT WASHER 3 8 FLAT WASHER ASUX 1 3 4 SHOULDER BOLT MAIN ASSEMBLY ELECTRIC LIFTING RAM ARM STEP 2 INSTALL LIFTING
Download Pdf Manuals
Related Search