Trademarks Disclaimer FCC Warning CE Mark Warning
Contents
1. are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment gen erates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interfer ence to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at whose own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to col lect such WEEE separately Revision PLANET Fast Ethernet Switch with 802 3af injector built in User s Manual FOR MODEL FSD 804P Rev 1 0 Part No 2010 A31110 000 Table of Contents Chapter 1 Introduction 1 1 1 Package Contents 1 1 2 How to Use This Manual 1 1 3 Product Features 2 1 4 Product Specifications 3 Chapter 2 Installation 5 2 1 Product Description 5 2 2 Installing a FSD 804P 6 C2. 000 o on o0o0ooo0 0000 10 PRI 23 4 F678 Figure 2 1 The front panel of FSD 804P J4 2 1 3 LED Indicators LNK ACT Green Light The port is successfully established Blink The port is actively receiving or sending the data 2 1 4 FSD 804P rear panel The rear panel of the Switch indicates an AC inlet power socket which accepts input power from 100 to 240VAC 50 60Hz 100 2400 10 Sener Figure 2 2 Rear Panel of FSD 804P Power Notice 1 The device is a power required device it means it will not work till it is pow ered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your switch from being damaged by unregulated surge or current to the Switch or the power adapter 2 2 Installing a FSD 804P This part describes how to install your FSD 804P Fast Ethernet Switch and make connections to the switch Please read the following topics and perform the procedures in the order being presented PLANET FSD 804P Fast Ethernet Switch do not need software configuration To install your FSD 804P on a desktop or shelf simply complete the following steps 2 2 1 Desktop Installation To install a FSD 804P on a desktop or shelf simply complete the following steps Step
3. 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green 4 Blue 4 Blue 5 White Blue 5 White Blue 12345678SIDE 2 6 Green 6 Green 7 White Brown 7 White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 12345678 SIDE 1 1 White Orange 1 White Green 2 Orange 2 Green 3 White Green 3 White Orange 4 Blue 4 Blue 5 White Blue 6 White Blue 12345678SIDE2 6 Green 6 Orange 7 White Brown 7 White Brown 8 Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 11 p Part NO 2010 A31110 000 K SAW
4. 1 Attach the rubber feet to the recessed areas on the bottom of the switch Step2 Place the FSD 804P on a desktop or shelf near an AC power source 5 Optional rack ear for 10 inch cabinet rack mounting RKE 10A NOTE and 19 inch cabinet rack mounting RKE 10B is available upon request Step3 Keep enough ventilation space between the switch and the surrounding objects When choosing a location please keep in mind the environ NOTE Mental restrictions discussed in Chapter 1 Section 4 Product Specification Step4 Connect your FSD 804P to network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports on the front of the FSD 804P B Connect the other end of the cable to the network devices such as printer serv ers workstations or routers etc Connection to the Switch requires UTP Category 5 network NOTE cabling with RJ 45 tips Please see the Appendex A for more information Step5 Supply power to the Switch A Connect one end of the power cable to the FSD 804P B Connect the power plug of the power cable to a standard wall outlet When the FSD 804P receives power the Power LED should remain solid Green 2 3 Installing Powered Devices The FSD 804P is able to support power to 4 IEEE802 3af compliant powered devices When the powered device is connected to the FSD 804P by an Ethernet cable at the first 4 ports the FSD 804P automatically detect the device and check if it is compliant wi
5. K absolute MAC addresses 1 Automatic address learning and address aging Supports Auto MDI MDI X function LED indicators for easy network diagnostic Comply with IEEE802 3 Ethernet IEEE802 3u Fast Ethernet IEEE802 3x Flow Control and IEEE802 3af Power over Ethernet EMI standards comply with FCC CE class B 1 4 Product Specifications Hardware Specification Network ports LED Display PoE RJ 45 Pin polarity Switch architecture MAC address Remote power feeding Per port feeding power Power Supply Operating Temperature Storage Temperature Humidity Dimension EMI Standard Compliance 8 Port RJ 45 for 10 100TX 4 Port with PoE injector function One power 1 4 port PoE in use LNK ACT 100 5 8 port LNK ACT 100 4 5 Positive 7 8 Negative Store and forward switch architecture Back plan up to 1 6Gbps 2K MAC address table with Auto learning function End point insert type and compatible with IEEE802 3af 15 4Watts maximum Embedded AC power supply AC 100 240V 50 60Hz 45 watts power consumption IEEE802 3 Ethernet IEEE802 3u Fast Ethernet IEEE802 3x Flow Control IEEE802 3af Power over Ethernet 3 Chapter 2 INSTALLATION This chapter describes the functionalities of FSD 804P s components and guides how to install it on the desktop or shelf Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description F
6. Trademarks Copyright PLANET Technology Corp 2005 Contents subject to which revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trade marks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representa tion either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no re sponsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incom plete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits
7. hapter 3 Switch Operation 3 1 Address Table 7 3 2 Learning 7 3 3 Forwarding amp Filtering 7 3 4 Store and Forward 7 3 5 Auto Negotiation 8 Chapter 4 Trouble Shooting 9 APPENDIX A 10 A 1 Switch s RJ 45 Pin Assignments 10 A 2 10 100Mbps 10 100Base TX 10 Chapter 1 INTRODUCTION 1 1 Package Contents Open the box of the Switch and unpack it carefully The box should contain the following items e The Switch e Power Cord x 1 e Users Manual x 1 If any item is found missing or damaged please contact your local reseller for replacement Please retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Ethernet Switch User Manual is structured as follows Chapter 2 Installation This chapter explains the functions and how to physically install the FSD 804P Chapter 3 Switch Operation This chapter explains the switch operation of FSD 804P Chapter 4 Trouble Shooting This chapter contains troubleshooting of FSD 804P Appendices This chapter contains cable information of FSD 804P 1 3 Product Features e 8 Port 10 100Mbps Fast Ethernet ports e 4 Port support 48VDC PoE power to IEEE802 3af compliant Powered Device e Hardware based 10 100Mbps auto negotiation e Flow control for full duplex operation and back pressure for half duplex opera tion e Integrated address look up engine support 2
8. or cost saving and flexible using of PoE power provision half of the 10 100Mbps TP ports of FSD 804P provide PoE power injector function which is able to drive 4 IEEE802 3af compliant powered devices For SOHO or department network the switches also provide a Simple and cost effective highly reliable network connection And is the ideal device for bridging Ethernet to Fast Ethernet workgroups or networks Therefore the switch will be the fast being recognized as one of the most important building blocks for today networking technology Solidly built in small size that is easy to position when space is at a premium Ideal for conference rooms class rooms study groups or small offices Place it on any flat surface or use the included wall mount kit to tuck it out of the way 2 1 1 Product Application Department Workgroup PoE Switch Providing up to 4 PoE in line power interface the switch can easily build a power central controlled IP phone system IP Camera system AP group for the enterprise For instance 4 camera AP can be easily installed around the corner in the company for surveillance demands or build a wireless roaming environment in the office Without the power socket limitation the switch makes the installation of cameras or WLAN AP more easily and efficiently 2 1 2 FSD 804P Front Panel Figure 2 1 shows the front panel of FSD 804P 20009 io 00 8 Port 10 100Mbps Ethernet Switch en j with 4 Port PoE Injector 0
9. red Thereby increasing the network throughput and availability 3 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Ethernet Switching stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability The Ethernet Switch scans the destination address from the packet header searches the routing table pro vided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability How ever the switch is most commonly used to segment existence hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Ethernet switching the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its respective domain and reduce the overall load on the network The Switch performs Store and forward therefore no error packets occ
10. th IEEE80 23af standard Then run the power provision process to provide power 6 Chapter 3 SWITCH OPERATION 3 1 Address Table The Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This in formation comes from the learning process of Ethernet Switch 3 2 Learning When one packet comes in from any port the Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 3 3 Forwarding amp Filtering When one packet comes from some port of the Ethernet Switching it will also check the destination address besides the source address learning The Ethernet Switching will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Ethernet Switching will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filte
11. the LNK ACT LED on the switch e Try another port on the Switch e Make sure the cable is installed properly e Make sure the cable is the right type e Turn off the power After a while turn on power again 9 APPENDEX A Switch s RJ 45 Pin Assignments A 1 1000Mbps 1000Base T BI_DA BI_DB 00 se 0006 soo 0006 Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard A 2 10 100Mbps 10 100Base TX When connecting your 10 100Mbps Ethernet Switch to another switch a bridge or a hub a straight or crossover cable is necessary Each port of the Switch supports auto MDI MDI X detection That means you can directly connect the Switch to any Ethernet devices without making a crossover cable The following table and diagram show the standard RJ 45 receptacle connector and their pin assignments RJ 45 Connector pin assignment MDI MDI X Contact Media Dependant Media Dependant Interface Interface Cross nenn a mer me mern a Term 10 The standard cable RJ 45 pin assignment The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable SIDE 1 SIDE 2 12345678 SIDE 14 White Orange
12. ur More reliably it reduces the re transmission rate No packet loss will occur 7H 3 5 Auto Negotiation The STP ports on the Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by detect the modes and speeds at the second of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Duplex mode If attached device is 1000Base T port will set to 10Mbps no auto negotiation 10Mbps 10Mbps with auto negotiation 10 20Mbps 10Base T Full Duplex 100Mbps no auto negotiation 100Mbps 100Mbps with auto negotiation 100 200Mbps 100Base TX Full Duplex J8 Chapter 4 TROUBLE SHOOTING This chapter contains information to help you solve problems If the Ethernet Switch is not functioning properly make sure the Ethernet Switch was set up according to instructions in this manual The Link LED is not lit Solution Check the cable connection and remove duplex mode of the Ethernet Switch Performance is bad Solution Check the full duplex status of the Ethernet Switch If the Ethernet Switch is set to full duplex and the partner is set to half duplex then the performance will be poor Please also check the in out rate of the port Why the Switch doesn t connect to the network Solution e Check
Download Pdf Manuals
Related Search