Version: 2.0
Contents
1. Not responding to DMX controller Check the DMX address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors of the fixture or the previous one Try to use another DMX controller Check to see if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit 25 USER MANUAL SPECIFICTAIONS Mains Input Fuse Total Power X Y Axis Beam Angle Control Mode Laser Power Laser Classification Laser Safety Standard Condition Temperature DMX Connections DMX Channels Measurement N Weight AC100 240V 50 60Hz 250V 3 15A Slow Blow 20mm Glass 50W 25 Auto Sound DMX Slave ILDA 350mW 650nm Red CW 60mW 532nm Green CW 50mW 473nm Blue CW Class 3B EN60825 1 2007 10 40 C 3 pins XLR Male Female Max 17 channels See picture below 12Kg Specifications subject to change without prior notice The availability of particular products may vary by region Please check with the dealer 262. a dance floor Do not operate laser without first reading and understanding all safety and technical data in this manual X Always set up and install all laser effects so that all lasers light is at least 3 meters 9 8 feet above the floor on which people can stand See Proper Laser Set up amp Usage section later in this manual Do not point lasers at people or animals Never look into the laser aperture or laser beams Do not point lasers in areas in which people can potentially get exposed such as uncontrolled balconies etc USER MANUAL Never point a laser at aircraft this is a federal offense Never point un terminated laser beams into the sky Do not expose the output optic aperture to cleaning chemicals Do not use laser if the laser appears to be emitting only one or two beams Do not use laser if housing is damaged or open or if optics appear damaged in any way Never open the laser housing The high laser power levels inside of the protective housing can start fires burn shin and will cause instant eye injury Never leave this device running unattended The operation of a class 3B laser show laser is only allowed if the show is controlled by a skilled and well trained operator familiar with the data included in this manual The legal requirements for using laser entertainment products vary from country to country the user is responsible for the legal requirements at the location country of use Alwa
3. with which you may be familiar The light from this product can potentially cause eye injury if not set up and used properly STOP AND READ ALL LASER SAFETY DATA Laser light is thousands of times more concentrated than light from any other kind of light source This concentration of light power can cause instant eye injuries primarily by burning the retina the light sensitive portion at the back of the eye Even if you can not feel heat from a laser beam it can still potentially injure or blind you or your audience Even very small amounts of laser light are potentially hazardous even at long distances Laser eye injuries can happen quicker than you can blink It is incorrect to think that because these laser entertainment products split the laser into hundreds of beams or laser beam is scanned out in high speed that an individual laser beam is safe for eye exposure This laser product uses dozens of milliWatts of laser power Class 3B levels internally Many of the individual beams are potentially hazardous to the eyes It is also incorrect to assume that because the laser light is moving it is safe This is not true Nor do the laser beams always move Since eye injuries can occur instantly it is critical to prevent the possibility of any direct eye exposure In the laser safety regulation it is not legal to aim Class 3B lasers in areas which people can get exposed This is true even if it is aimed below people s faces such as on
4. 7 128 different fixed position on Y axis CH 16 X AXIS 128 191 Clockwise moving MOVING 192 255 Anticlockwise moving CH 17 ee MOVESPEED 0 255 Fast to Slow 22 USER MANUAL PATTERN LIST 016 031 SIT 7 i ear AN N V S P O OO Oo 0 go 096 111 Sir ww 2 gf A y t U U 23 USER MANUAL MAINTENANCE e Make sure the area below the installation place is free from unwanted persons during servicing e Switch off the fixture unplug the mains cable and wait until the unit has been cooled down e Housings fixations and installations spots ceiling truss Suspensions should be totally free from any deformation e The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected e n order to protect the fixture from overheat the cooling fans if any and ventilation openings should be cleaned monthly e The cleaning of aperture glass and scanner mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics 1 Clean with a soft cloth using normal glass cleaning products 2 Always dry the parts carefully 3 Clean the Aperture glass at least once every 30 days e The interior of the fixture should be cleaned annually
5. AFETY INSTRUCTIONS Every person involved with installation and maintenance of this device has to e Be qualified e Follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left out premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel X Always plug in the power plug least Make sure that the power switch is set to off position before you connect the device to the mains The power plug has to be accessed after installing the device e Nade sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it
6. D 016 055 AUTO SHOW 1 056 095 AUTO SHOW 2 CH 1 096 135 MUSIC SHOW 1 MODES 136 175 MUSIC SHOW 2 176 215 DMX Mini Preprogram Show Mode 216 255 DMX GOBO MODE DMX MINI PREPROGRAM S H aea MODE CHANNEL VALUE DESCRIPTION CH 2 000 255 46 Mini preprogram laser shows SHOWS 20 USER MANUAL DMX GOBO MODE CHANNEL VALUE DESCRIPTION CH2 a BOUE 000 255 8 Group CH 3 PATTERN 000 255 16 Patterns in each group Lees e 9 o Full pattern without clipping CH 5 CLIPING 001 127 096 9996 fixed pattern clipped 128 255 Clipping Speed Hn n 000 127 100 5 fixed pattern zoomed CH6 128 169 Zooming IN ZOOMING 170 209 Zooming OUT 210 255 Alternately Zooming CH 7 Fast to Slow 21 USER MANUAL CH8 000 127 0 359 degree fixed Y axis rolled Y AXIS 128 191 Clockwise rolling ROLLING 192 255 Anticlockwise rolling CH9 ee ROLLSPEED 0 255 Fast to Slow 000 127 0 359 degree fixed X axis rolled CH 10 X AXIS 128 191 Clockwise rolling ROLLING 192 255 Anticlockwise rolling CH 11 ee ROLLSPEED 0 255 Fast to Slow 000 127 0 359 degree fixed Z axis rolled CH 12 Z AXIS 128 191 Clockwise rolling ROLLING 192 255 Anticlockwise rolling CH 13 ee ROLLSPEED 0 255 Fast to Slow 000 127 128 different fixed position on X axis CH 14 X AXIS 128 191 Clockwise moving MOVING 192 255 Anticlockwise moving CH 15 ee MOVESPEED 0 255 Fast to Slow 000 12
7. DOWN to select pattern mirror mode as above e Press ENTER to confirm the setting uH DMX 512 1 2 3 oe FUNC UP DOWN ENTER In the MODE OPTION setting the pattern mirror mode that you are going to choose is flashing Press UP or DOWN to change pattern mirror mode you will have 4 different pattern mirror mode Their DISPLAY and OUTPUT are listed below Attention Beside of LED programmed mirror reverse setting the laser scanned world could be set by ILDA control panel 19 USER MANUAL ILDA Control Mode e This unit has the ILDA DB25 port and it can be controlled by the PC There is auto transform set in the inside of the unit to transform the ILDA and preprogrammed show when connecting with the 25 pin cable the unit will be control by PC when disconnect the unit it will be preprogrammed program control e n the theory as long as it is ILDA B25 It can control this unit but in the reality some of the software can not control this unit for the 4 pin and the 17 pin of the output card has not connect In fact this is an easy problem As long as you connect them It can control this unit DMX Channels Chart f ATTENTION Several optional operating modes were preprogrammed set into this laser projector at DMX channel 1 Before control other DMX channels please be sure that the channel 1 was set in proper mode value DMX PROTOCOL CHANNEL VALUE DESCRIPTION 000 016 Laser OFF
8. LSX 500SRGB Version 2 0 This manual contains important laser system safety and operation information Read and understand all instructions prior to powering on laser unit the first time to avoid laser eye injury and to avoid breaking the law Keep this manual in a safe place for future reference USER MANUAL WARNING DATA Lasers can be hazardous and have unique safety considerations Permanent eye injury and blindness is possible if lasers are used incorrectly Pay close attention to each safety REMARK and WARNING statement in the user manual Read all instructions carefully BEFORE operating this device A Attention e Important Caution A Laser es Recycle eo Indoor 4 Disposal f Location Indicates a skill or other useful information for special situations Indicates important information to protect people from laser incident or injury Prevent damage or injury from incorrect operation Laser safety warming labels To protect the environment recycle packing material wherever possible The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or other fluids Don t throw this product away just as general trash please dispose of this product following the abandon electronic product regulations in your area The projector must be installed in a location with adequate
9. Only handle the power cord by the plug Never pull out the plug by tugging the power cord Itis essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a USER MANUAL qualified employee Do not switch the fixture on and off in short intervals as this would reduce the laser diode life 6 Eor replacement please use fuses of same type and rating only e If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Do not shake the device Avoid brute force when installing operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or duct There should not be any cables lying around You endanger your own and the safety of others The minimum distance between the fixture and surrounding walls must be more than 50cm Always fix the fixture with an appropriate safety rope Fix the safety rope at the safety rope only The ambient temperature must be between 10 C to 40 C Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons CAUTION Operate the device only after having familiarized with its functions D
10. anel as well BIG Microphone Turn the knob to adjust the sound activated sensitivity ILDA INPUT Standard ILDA DB25 Input ILDA DB25 Standard ILDA DB25 Input ILDA OUT Standard ILDA DB25 Output thought Laser beam output indicator LED LDA ILDA connection indicator LED Green is connection and red is disconnection USER MANUAL Front Panel mol mme renon 19 POWER Indicates that the unit is switched on DMX connection indicated LED Red is DMX DMX connected Green is preprogram standalone mode Flashes to the sound of the music MUSI i Laser output Laser output aperture HANGING With 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook Um WARNING LABEL 25 WARNING LABEL Caution Class 3B laser BRACKET LASER WARNING warms against apotentially dangerous SIGN laser when not used by skilled operators WARNINGLABEL Laser radiation Avoid exposure to beam Class 3B laser product USER MANUAL e IMPORTANT e For your own safety and full laser safety regulation we do strongly recommend you to take this optional switch CONTROL amp FUNCTION e Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use e Do not switch the unit on and off in short time intervals e Always unplug the unit when it is not used for a longer time Or before replacing the bulb or start servicing e Inth
11. e event of serious operation problems stop using the fixture and contact your dealer immediately A Attention Laser will be output from laser aperture in 5 seconds after the unit is powered on Operating Mode When laser is powered on LED monitor on rear panel shows the current operating standalone mode or DMX address of DMX mode With help of LED control panel is very easy to set and change the operating mode of laser After every resetting and saved the new mode information will be shown on LED monitor at next power on FUNG Mode Function Option to choose the operating mode of laser ENTER Confirmation to confirm all setting or change of LED control panel UP DOWN to change operating mode parameter or DMX address DOWN USER MANUAL Operation POWER ON LASER FUNC UP DOWN UP DOWN DOWN H3lN3a H3LlN3 Stand Alone Preprogram Laser Show Press FUNC to enter MODE OPTION e Tilto LED panel show any one of A1 A2 S1 S2 X Press UP or DOWN to select your favorite Stand Alone mode as above Press ENTER to confirm the setting The laser is working in stand alone Each time when you turn on your laser you have this confirmed laser show DMX 512 1 2 3 oe o FUNC UP DOWN ENTER In the MODE OPTION setting the stand alone laser show that you are going to choose is flashing Press UP or DOWN to change stand alone laser show you will have 4 different stand al
12. ety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails e Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated CAUTION When installing the device make sure there is no highly in inflammable material decoration articles etc in between a distance of min 0 5 meter USER MANUAL RODUCT OVERVIEW Rear Panel vel wwe me Cs RN Se DC NNUS oan soot DTI NUT o ermen oe e ieoor perae ocorre nesre o emm a NN Se ee USER MANUAL ILDA Hardware Setting Panel ILDA CONTROL oooooooooooo e GD QG 0000000000000 OR ILDA INPUT OG QB Soccocscosce ONDA O ILDA OUTPUT O FUNCTION O E The Size of X Y axis adjustment Y SIZE X MIRROR X Y axis mirror setting It could be done by Y MIRROR LCD control p
13. nn l n Hi NN un 1 a 1 9 DMK 512 12002 E X Controller operation nn a T vin im i N M Jj 1 1200 Mastar siave N 1 T ee j ___ L Oneal ll 1200 If you are using the standard DMX controllers you can connect the DMXc output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect output with the input of the next fixture until all fixtures are connected If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pins adapter At last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pins XLR plug and plug it in the DMX output of the last fixture Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system The DXM output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit Each fixture needs to have a DMX address to receive the data from the controlle
14. o not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION If this device will be operated in any way different to the one described in this manual the product may suffer damages and the warranty void USER MANUAL BEFORE OPERATION Unpacking Instructions N CAUTION Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling Save the package and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing What is Included The carton or flight case contain following items Laser Light KEYs for key switch 2PCS Power Cord Interlock Connector EL N 1 PCS 1 PCS q 20m DB25 ILDA Cable 1 PCS USER MANUAL Flight Case Power Supply To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture of refer to the fixture s specifications chart A fixture s listed current rating is its average current draw under normal conditions All fixtures must be powered directly off a switched circuit and can n
15. one preprogrammed laser show Their DISPLAY and EFFECT are listed below USER MANUAL DISPLAY STAND ALONE MODE LASER EFFECT Auto laser show with random order Auto laser show with traditional order Sound activated laser show with random order Sound activated laser show with traditional order A Attention In S1 or S2 MODE Sound Activated Mode the laser will be blocked out in 3 second when MIC Signal was not detected DMX MODE e Press FUNC to enter MODE OPTION e ilto LED panel shows 001 e Press UP or DOWN to select the DMX 512 ADDRESS among 001 512 e Press ENTER to confirm the setting The laser is working in DMX MODE With help of UP and DOWN button the DMX address could be set DMX 512 EE 2 3 o o Oo O FUNC UP DOWN ENTER Pie Attention In DMX MODE once the DMX cable is connected with laser and DMX controller the DMX LED in front panel of laser will be ON SLAVE MODE e Press FUNC to enter MODE OPTION e Till to LED panel shows SLA e Press ENTER to confirm the setting The laser is working in SLAVE MODE Connect MASTER laser with several SLAVE laser with DMX cable the SLAVE lasers do what exactly the MASTER laser does Please check 5 2 DMX connection to have more details about laser connection USER MANUAL DMX 512 oe o o FUNC UP DOWN ENTER PATTERN MIRROR REVERSE SETTING e Press FUNC to enter MODE OPTION e Till to LED panel show any one of 5 4 S F e Press UP or
16. ot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch Before applying USER MANUAL power to a fixture check that the source voltage matches the fixture s requirement The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration FUSE 5mmx20mm FUSE E 1 A 250V Cable EU Cable US Pin Light blue White Neutral Yellow Green Green Earth DMX 512 connection between fixtures The fixture is equipped with 3 pin XLR sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal N Caution At the laser fixture the DMX cable has to terminate with a terminator Solder a 120 Ohm resistor between Signal and Signal into a 3 pin XLR plug and plug and plug it in ye P 4 3 4 l L the DMX output of the last fixture IN 3 N 2 USER MANUAL Building a serial DMX chain iti ii T E Tt zum aa Da a kd at a K ES e aoa a T EB m D EB 6 i
17. r The DMX address number which could be read from rear panel of each fixture is between 000 511 The end of the DMX 512 chain should be terminated to reduce signal errors USER MANUAL Proper Laser Set Up amp Usage This fixture has been designed to be hung lt is recommended for safety purposes your lighting effect are properly mounted using a suitable hanging clamp and safety cable Items appropriate for safe and effective mounting are easily sourced from your lighting vendor International laser safety regulations require that lasers must be operated in the fashion illustrated below with a minimum of 3 meters 9 8 ft of vertical separation between the floor and the lowest laser light vertically Additionally 2 5 meters of horizontal separation is required between laser light and audience or other public spaces oo 3 0 Meters CAUTION Use of controls adjustments or performance of procedures other than what is specified herein may result in hazardous radiation exposure Rigging the Fixture CAUTION Please consider the respective national norms during the installation The installation must only be carried out by an authorized employee or dealers 11 USER MANUAL e The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary saf
18. using a vacuum cleaner or air jet aaa XIII ATTENTION We strongly recommend internal cleaning to be carried out by qualified worker TROUBLE SHOOTING Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting The fixture does not work no laser and the fan does not work 1 2 Measure the mains voltage on the main connector 3 Check the connect power and main fuse Check the power on indicated LED 24 USER MANUAL uS LM as c Fw M Z A The fixture is power on but no laser coming out from aperture Check the laser aperture cover Check the key switch Check the remote interlock or interlock connector Wait for at least 30 minutes to warm up in low temperature Check whether it is in music mode without sound signal Check whether it is in Slave mode Check whether it is in DMX without DMX signal The laser effect power is very weak Wait for at least 30 minutes to warm up in low temperature Clean the scanner mirror with alcohol Clean the aperture glass with alcohol Check whether it is in DMX with high strobe frequency The laser is on but the pattern is not moving Check to see whether it is in Music Sound mode without detecting sound signal Check to see whether it is in DMX mode with further DMX control Try to change the fixture to another stand alone mode Try to control the fixture with DMX to see the laser effect system
19. ventilation at least 50cm 20 inches from adjacent surfaces Be sure that no ventilation slots are blocked USER MANUAL LASER SAFETY WARNINGS e Potential laser injury hazard exists with this product Read these instructions carefully which includes important information about installation safe use and service N Caution Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser light N Caution This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes N Caution It is illegal and dangerous to shine this laser into audience areas where the audience or other personnel could get direct laser beams or bright reflections into their eyes N Caution Itis a US Federal offense to shine any laser at aircraft N Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact the dealer nearest to you NON INTERLOCKED HOUSING WARNING This unit contains high power laser devices internally Do not open the laser housing due to potential exposure to unsafe levels of laser radiation The laser power levels accessible if the unit is opened can cause instant blindness skin burns and fires USER MANUAL LASER SAFETY AND OPERATING INSTRUCTIONS o Laser light is different from any other light source
20. ys use appropriated lighting safety cables when hanging lights and effects overhead LASER SAFETY LABEL REPRODUCTIONS This is only one laser aperture on this product The label indicates the laser beam output aperture Caution Class 3B LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM LASER RADIOATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT USER MANUAL LASER EXPOSURE WARNING A LASER LIGHT AVOID DIRECT EYE EXPOSURE Further guidelines and safety programs for safe use of lasers can be found in the ANSI 2136 1 Standard For Safe Use of Lasers available from www laserinstitute org Many local governments corporations agencies military and others require all lasers to be used under the guidelines of ANSI Z136 1 Laser Display guidance can be obtained via the International Laser Display Association www laserist org LASER EMISSION DATA aane G gt 60mW R Cooling TEC amp Fan Cooling Scanning DC to 20KHz 25 Degrees X amp Y As measured under IEC measurement conditions for classification Note The laser diode is exposed to extreme conditions due to the high output power and therefore only has a limited life Like all wear parts the laser diode is not subject to any guarantee claims LASER COMPLIANCE STATEMENT This laser product complies with EN IEC 60825 1 Ed 2 2007 03 and US FDA CDRH FLPPS via the terms of Laser Notice No 50 dated June 24 2007 B USER MANUAL GENERAL S
Download Pdf Manuals
Related Search