BS 200/BS 300 - ATO FORM GmbH
Contents
1. Page 15 ato form Assambly of extension cushion Assembly of extension cushion Accessories The extension cushion is mounted onto the two guide rails between the lower and upper cushion Page 16 Assembly of posterior support Accessories The supporting adaptor for the posterior Support is mounted as shown onto the long guide rails Lead the bars through the extension cushion and the posterior support Fasten with the handle The posterior support can be adjusted as shown The posterior support can be swung aside for easy entering and exiting Facanee ato form Assemby of posterior support PR Pr 1 ee ato form Therapy table for prone and supine position Therapy table for prone and supine position Accessories Firstly loosen the clamping lever on the con nection bar between the frame and board Hold on to the tilt table and pull out the security lock Release the locking pin when the stander is in the required position and ensure the locking pin clicks into place Finally fasten the clamping handle securely Page 18 Knee supports for supine position Accessories Place the fittings of the knee supports into the side guides and using the allen screws fasten in the desired height A Then slide the knee supports into the fit tings and fasten using the star grips B You can adjust the knee supports sideways on the rail as well ato fo2. Use of non original spare parts Non observance of the given instructions in this operating manual Exceptional events Clean the prone supine and upright stan der BS in accordance with the instructions in the chapter Cleaning We constantly develop new aids and improve existing products We will be happy to receive your suggestions of any description Page 7 ato form Warranty and Product Liability Warranty and product liability ATO FORM grants the required by law warranty of your country against defects in workmanship and materials The warranty would be adversely affected if the customer s responsibility of servicing and or daily maintenance is not carried out according to the guidelines and intervals prescribed by the supplier and or stated in the manual For further information we refer to the ATO FORM homepage download www ato form com The warranty can only be sustained if the ATO FORM product is in use in the same country where it was purchased and if the product can be identified by the serial number The warranty does not cover accidental damage including damage caused by misuse or neglect The warranty does not extend to non durable parts which are subject to normal wear and tear and need periodic replacement The warranty is null and void if non original ATO FORM parts accessories are used or if the product is repaired or altered by anyone other than an authorized ATO FORM representati
3. and knowledge of operators which they gained from for example training courses Ensure all users of this aid understand its handling and the meaning of the symbols attached to the device Accidents can be prevented when technical instructions according to the EWG guidelines are followed Protective coverings and labels may not be removed The prone supine and upright stander should only be used on even surfaces Never use the BS on rough terrain steeply sloping ground or stairs Regular monitoring at your specialist dealer at least once a year lengthens the life time of the prone supine and upright stander BS and gives you security Page 5 ato form Important Warnings Important Warnings When using a prone supine and upright stander the center of gravity is always rela tively high up A person using a prone supine and upright stander is always dependent on the stability of the device from the supporting points against the body and support area to the floor Our main objective was to develop a device which satisfies the demands of many medical indications Nevertheless a prone supine and upright stander cannot be used without exception in all situations The application and utilization should always be followed through with sense and reason e Before using the prone supine and up right stander BS carefully read all instruc tions of this user manual as these have been drawn up for your safety
4. reseller from whom you purchased the device from Control before every use that all adjustable parts are always locked Check regularly if all screws and hand les etc are tightly fastened Worn and defect parts are to be repaired or replaced immediately This is especially important to ensure a safe use of the aid Carefully check for a firm hold of the clamping jigs and the like Adjust settings only in the unloaded con dition ato form Important Warnings Be careful when moving the standing aid whilst a patient is standing in the device This is particularly applicable when cros sing ramps thresholds and similar Never allow persons not familiar to operate the standing aid respectively those who have not read this operating manual Always demand original spare parts In case of an accident contact the manu facturer for a speedy investigation The manufacturer can accept no respon sibility for damages caused by unsuitable and incorrect application of the device by the user neglected maintenance unau thorized alterations and modifications the use of non original spare parts unpre dictable and exceptional events or from non observance of the instructions of this operating manual The manufacturer bears no responsibility for damages caused to persons objects or animals in the following cases Incorrect use of the aid Use of the device by non suitable persons Incorrect mounting of parts or accessories
5. 5 BSZ 306 5550 5 BSZ 307 5550 5 BSZ 308 5550 5 BSZ 310 5550 5 BSZ 313 0550 4 BSZ 316 0550 4 BSZ 320 0550 BSZ 314 0550 1 BSZ 315 0550 OK Abductor wedge Heel support pair for prone position Thorax Pelvis support pair Extension cushion type 5 narrow high 28 cm 23 cm Extension cushion type 6 wide low 46 cm 17 cm Chin support Head support with facial aperture Posterior support Knee support for supine position Therapy table for prone and supine position Tilt adjustment with foot control Foot plate pair Electric motor additional component Further information regarding the accessories can be found on our homepage Page 23 ato form Technical details Technical details prone supine and upright stander BS Sizer Size 3 Armpit height 83 pis 12 Fem m 115 Dis 153cm Overall width 59 cm 63 cm Overall length 85 cm 111 cm Overall height basic model max 100 cm Overall height including all accessories max 140 cm max 135 cm max 195 cm Overall height horizontal 64 cm 72 cm Access height 10 bis 15 cm 10 bis 15 cm Support pad large width x height 36 x 50 cm 47 x 81 cm Support pad small width x height 32 x 26cm 36 x 36 cm Tilt 5 bis 90 5 bis 90 Loading capacity 70 kg 100 kg Overall weight 21 kg 33 kg Overall height including all accessories foot plate up to upper edge of supporting surface Technical changes reserved Page 24 Cleaning Maintenance Leftover
6. User Manual prone supine and upright stander BS 200 BS 300 ato forrni e Standing Aids edition 13 13 Dear Customer We would like to thank you for your trust extended to us and for purchasing our product The prone supine and upright stander BS 200 BS 300 distinguishes itself by its quality security easy operation and modern design For optimal use of this aid we ask you and other possible users to carefully read this operating manual Please read this user manual carefully before first use and handle equipment appropriately lust for life ato form Foreword Page 3 ato form Table of contents Table of contents Topic Page Topic Page Safety instructions wcvensvenioresaereneardiece 5 Assembly of posterior support 17 Important Warnings 6066 6 7 Therapy table for prone Warranty and product liability 8 ANG SUPINE POSITION ciascencietenscaniennes 18 Purpose Ol USS sevacerevececsigeenicececuvecs 9 Knee supports for supine position 19 Position of CE sign saicincvswenimnnannitoasans 9 Manual tilt adjustment or xuccsurcancpensains 20 MA CATIONS sescsisiescernrissiesireriseekatar 9 Electric tilt adjustment 21 Equipment OVEMVIEW sincvclacmscmeneinnents 1O UOC BS 200 anamensis 22 BE E E A E 11 AGcessanes BS 200 ariiunipnpieipikena 22 Belts and foot support 0 000 11 TY P BS 200 arera narii 23 Assembly of heel
7. and as a guideline for the correct use and care of this product This operating manual is an indispensable component of the delivery and should be stored carefully for further use The operating manual is intended for retailers and users of the prone supine and upright stander BS it contains the required information to secure the correct use of the product cannot not however replace the necessary experience of the user or assistant in handling the device The reseller has the duty to deliver the device ready for operation and to explain precisely the functions and technical data of the device as well as the necessary support and briefing needed for a correct and efficient use of the device Page 6 The given instructions of the operating manual refer to the point in time of the device being placed on the market The manufacturer reserves the right to introduce any modifications that prove necessary to the device and associated operating manual without being bound to change previous devices and associated operating manuals The prone supine and upright stander BS may only be operated with continues pre sence of a qualified person respectively a family member of the user The BS may only be used by persons of a suitable stature and physical aptitude The BS is only intended for use inside buildings The BS may only be operated by persons who have familiarized themselves with the standards and rules of the present o
8. ixate the electro box unit accordingly Fig 3 Now you can mount the drive unit to the frame and board Fig 4 and 5 fai mh Hereby it is necessary to place the fm S F black adapter between the frame and motor Finally connect the cable of the drive unit and the remote control cable with the electro box Fig 3 Page 21 ato form Types Accessories BS 200 Types BS 200 7550 5 BS prone supine and upright stander size 2 frame blue Accessories Following accessories are available for the BS prone supine and upright stander BSZ 201 5550 5 Abductor wedge BSZ 212 7550 4 Heel support pair for prone position BSZ 203 5550 5 Thorax Pelvis support pair BSZ 205 5550 5 Extension cushion type 3 narrow high 27 cm 23 cm BSZ 206 5550 5 Extension cushion type 4 wide low 36 cm 11 cm BSZ 207 5550 5 Chin support BSZ 208 5550 5 Head support with facial aperture BSZ 210 5550 5 Posterior support BSZ 213 0550 4 Knee support for supine position BSZ 226 0550 4 Therapy table for prone and supine position BSZ 220 0550 Tilt adjustment with foot control BSZ 214 0550 1 Foot plate pair BSZ 215 0550 OK Electric motor additional component Page 22 Types BS 300 9550 5 Accessories ato form Types Accessories BS 300 BS prone supine and upright stander size 3 frame green Following accessories are available for the BS prone supine and upright stander BSZ 301 5550 5 BSZ 302 7550 4 BSZ 303 5550 5 BSZ 305 5550
9. made to the prone supine and upright stander or its parts by unauthorized persons voids any warranties In these cases any product liability granted by the manufacturer ATO FORM GmbH Zur Lauterhecke 34 D 63877 Sailauf voids in advance For all questions about spare parts and accessories contact your specialist dealer or the ATO FORM Service 0049 6093 944 0 In environmental protection matters All packaging parts are re useable The cardboard packaging is to be recycled as waste paper We therefore use paper as filler material Possible used plastic film of the packaging are made out of PE and are therefore low in pollutant and can either be recycled or burnt Page 26 lust for life ato form Selection from our programme E Walking aids E Gait trainer E Standing aids E Seating aids E Hoists E Body Protection E Customized solutions Thank you for your interest in our products For questions please contact ATO FORM GmbH or your specialist dealer Your ATO FORM Team Your specialist dealer ATO FORM GmbH Zur Lauterhecke 34 D 63877 Sailauf phone 0049 6093 944 O E Mail info ato form com www ato form com
10. perating manual Never place a patient in a standing aid which is not coordinated with his or hers body height and weight Do not place any hot containers or objects on the therapy table as hereby the wood or coating could be seriously damaged Do not place any heavy objects on the standing aid for example on the table as it would affect the center of gravity and consequently impair the balance Do not operate or take any action if unsu re of its effects if in doubt please contact the nearest technical service center or manufacturer Always ensure there are no obstacles in operating range of the BS such as car pets stairs or objects on the floor which could lead to the BS overturning Move all objects out of the way which could be hit or fall whilst operating the prone supine and upright stander BS The use of the prone supine and upright stander BS and its auxiliary equipment must be administered under medical supervision Never use the BS on rough terrain steeply sloping ground or stairs Never leave the user of the BS unatten ded with the device Do not use the BS before locking the wheels of the standing aid Do not use the prone supine and upright stander BS without ensuring a correct mounting of the safety belts Never place the prone supine and upright stander BS on steep grades Do not use the device if any parts are damaged or missing In case of malfunction or accident contact the
11. rm Knee supports for supine position Please adjust the knee supports to suit the individual needs of the user Place the fitting in the slot and fasten in the desired height Then place the bar in the fitting and fasten with the handle Mount the knee support bars in the fittings and fasten The knee supports adjust sideways Use the handle me Page 19 ato form Manual titl adjustment Manual tilt adjustment Firstly loosen the clamping lever on the connection bar between the frame and board Hold on to the tilt table and pull out the security lock Release the locking pin when the stander is in the required position and ensure the locking pin clicks into place Finally fasten the clamping handle securely Page 20 ato form Electric tilt adjustment Flectric tilt adjustment Accessories Electric tilt adjustment is only available for BS sizes 2 amp 3 Mounting of the electro box only needs to be carried out if the electric drive is ordered separately When ordering a BS prone supine and ya upright stander with electric tilt adjustment it is delivered completely mounted Firstly dismount the connection bar for the manual tilt from the top of the stander and frame Fig 1 using an allen key and fork wrench Then fitting for the manual tilt bar has to be exchanged with the new one according to Fig 2 Fasten the mounting plate for the electro box to the frame and f
12. s dirt and dust are always to be removed Moving parts operate better if you apply one drop of acid free sewing machine oil after cleaning Belts are best cleaned using water and a mild detergent The upholstery is made of imitation leather and is washable When using any cleaning agent please follow instructions of the manufacturer For the protection of the warranty it is especially important that BS prone supine and upright stander is serviced regularly once a year from the date of purchase Please request the relevant maintenance checklist Re use The product BS was designed so it could be reused after implementation of various measures Following measures should be followed Thorough cleaning and disinfecting using appropriate cleaning agents Maintenance following the maintenance schedule of the manufacturer or autho rized specialist dealer Preparing accompanying documents and release for re use ato form Cleaning Maintenance Re use Warning Do not use strong solvents which could damage the surface of the device The use of a high pressure cleaner is not recommended Page 25 lust for life ato form Spare Parts Storage Spare Parts Storage Only original accessories and original Keep these operating manual in a safe place spare parts may be used Non compliance after reading so that you can refer to them with these instructions and repairs carried at a later date out or modifications
13. support 12 Accessories BS 300 o ae 23 Assembly of chin support 5 12 Technical details sosvaceieecaiaewserticeceecses 24 Assembly of thorax supports 13 Cleaning Maintenance 25 Assembly of headrest PRO 16 ANEA P E TTT 25 with facial aperture 0eeeeee 14 Spare paii eaii 26 Assembly of abductor wedge 15 Siorage aasudinccens aoe oneeiaeseionracnane 26 Assembly of extension cushion 16 Page 4 Safety instructions The prone supine and upright stander BS 200 BS 300 is labeled with the CE mark and complies with the requirements of Directive 93 42 EWG It was developed in line with most recent findings Production is subject to an on going quality control It was developed in accordance to the newest insights The manufacturing process is subject to constant quality control Please read this user manual carefully before operating the prone supine and upright stander The user manual is an integral part of the prone supine and upright stander In case of loss request a new copy Please keep the user manual in a safe place accessible to care and maintenance staff The user manual does not replace the experience of supervisory staff In the event of specific or difficult applications the user ato form Safety instructions Important Warnings CE manual represents a guide to the most important handling with the experience
14. t Delivery All BS prone supine and upright standers are delivered in a robust carton and operational immediately after unpacking Belts and foot support The belt is moved freely guided through the rail and fixed by a star grip The height and angle of the foot rest is adjusted using a clamping lever as shown Page 11 ato form Assembly of heel support Assembly of chin support Assembly of heel support Accessories The heel support is guided through the slot from underneath the foot rest and screwed on Assembly of chin support Accessories Mount the chin support onto the bars as shown and fasten screws carefully Page 12 ato form Assemby of thorax supports Assembly of thorax supports Accessories Place the thorax supports fittings into the lateral guides as shown and fasten the allen screws into the desired height Then push the side supports into the holder and fasten using the star grip Page 13 ato form Assembly of headrest with facial aperture Assembly of headrest with facial aperture Accessories Push the long guide rails about 15 cm up i wards and secure the headrest into the mid a a E REA pipes fasten by use of the clamping screws Page 14 ato form Assembly of abductor wedge Assembly of abductor wedge Accessories Push the abductor wedge through the slot centered in the lying surface Fasten on the backside using the allen screw
15. ve or by trained personnel officially recognized by ATO FORM for repair and maintenance of ATO FORM products ATO FORM reserves the right to inspect the product being claimed for and the relevant documentation before agreeing to the warranty claim and to decide upon whether Page 8 to replace or repair the defective product It is the customer s responsibility to return the item being claimed for under warranty to the address of purchase The warranty is given by ATO FORM or subsequently an ATO FORM dealer Purpose of use The prone supine and upright stander BS is only intended for indoor use It offers a variety of therapeutic applications such as standing frame prone board and supine board or as a drainage support The optional therapy table supports optimal head control training We wish you every success using the prone supine and upright stander BS Position of CE sign The CE label is located on the frame on the underside of the cross bracing Indications e Cerebral palsy e Muscular dystrophy e and others ato form Purpose of use Position of CE sign Indications Page 9 ato form Equipment overview Equipment overview Lower supporting cushion Upper supporting cushion Safety belts UN VD gt Manual tilt adjustment I QA mn m Swivel wheels lockable Foot plate partitioned Frame Therapy table Extension cushion narrow high ato form Delivery Belts and foot suppor
Download Pdf Manuals
Related Search