Common manual of TS-1093 and TS-1068 iOS and
Contents
1. your phone must be turned on and sensor probe should be connected with device before this THERMSmart kod 1 Choose High Temp onthe Opening Page 2 Choose the High Temp 5 Register Button on C the Device List Page 3 Choose Add Button amp onthe Register Page 4 Press Register Button device you want to view If the registration is successful the Registered Page will be returned Registered Sensors s Keo Ome lt Add New Sensors THERMSmart 286 9675 1F0 73F 1 0643 THERMSmart 62A14D1D S8CA 1C1D Settings with Registered Page lt Sensors E Registered Sensors con DEDO con DEDO Below settings can be done onthis page Name a Device Pressing will allow you to change the name of a device Unregister a Device If you do not want to view a device any more press toremove it Find a Device Pressing willturn onthe LED light This will help to locate itand tellif it is on Uses of Device List Page 19 lt High Temp E 8 on iOS only A Kitchen Thermo 1 Default Preset ll Temperature Timer 28 c 00 00 00 Goo THERMSmart hi temp Default Preset 7 c 00 00 00 BO M Temperature Window where the readings are displayed Touch itto enter the Setting Page to set Temperature Alarm and Timer 2 If device and the phone are out of range readings transmission will be paused until connection isrestored The2. Bluetooth Thermometer User Manual Introduction This Bluetooth Thermometer works with phones or mobile devices with iOS7 or Android 4 3 Before use make sure the Bluetooth alarm and notification functions areturned on Asthis deviceis built with Bluetooth Smarttechnology pairing isnot needed Download and install the Thermsmart app before getting started The app is available at App Store and Google Play GETTING START Install Batteries Two pieces of AAAsize 1 5V batteries are needed Alkaline batteries will be recommended The battery compartment is found at the back of the unit Ascrewdriver may be needed to open and close the battery door depending on the version you have When batteries are put in properly the device will be turned on automatically andthe LED light willbe flashing for afew seconds CAUTION RISK FOREXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION Turning On and Off the unit To turn on the unit press the On Off button on the frontonce TheLCD willbe onand the LED will be flashing fora fewsecond toconfirm To turn off hold this buttonfor a few second When the LCD display is off release hold Very rarely irregularity may be seen in function because ofinterference Should this happen close the app and open it again Register the unit Before a device can be viewed it must be registered withthe app first Bluetooth of
3. Temperature Window atthis time will turn gray without reading 3 Press this to lightup the LED to locate it 4 Battery Capacity Status 5 Temperature Alarm Indicator to show if any temperature alertis turned on 6 Bluetooth Connection Strength 7 Timer Start and Stop Buttons 8 Register Button to register or unregister device 9 Back Button for iOS Use System s Back Button for Android Settings with Device Setting Page 8 Cancel Settings Confirm 7 on iOS only Kitchen 2 B 6 Default Preset 9 Highest ves Temperature Alert Temperature Alert 40 c l f 3 E pg Starting Time A of Timer 00 00 00 4 am s Touching the Temperature Window will take you to this Device Setting Page Following functions can be done Turn the Temperature Alarms On Off Highest and Lowest Temperature Alarms are available Press or 2 to turn onor off If both are turned on itwill becomea Range Alarm Set the Temperature Alarms Touch 3 to pop up the setting window for this Set the Timer Touch 4 to pop up the setting window of timer Run the Alarm and Timer Press 7 to confirm all the settings The Device List Page will be returned The temperature alarm willrun automatically with Alarm Indicator Eq displayed For Timer press to start and to stop If you want to abandon the settings press 8 for iOS or System s Back Button for Android Please note if the temperature alarmis turned on the device will be
4. come viewable only onthe phone thatturns onthe alarm Save a Setting The Temperature Alarm and Timer settings can be saved for re use To dothis press 5 Name a Setting Press 9 to name orre name a setting Retrieve Preloaded or Saved Setting Press 6 willtake you to Preset Page Uses of Preset Page ancel Select a Preset USDA Temperature Tempura Oil Temperature v User Custom Preset Default Preset amp v0 00 0 J My Recipe 470 c YO c 901 Use the Preset Two sets of Preloaded and one set of Custom settings areavailable To openthe menu touch the title and then choose the setting wanted Delete aCustom Preset Only the settings under User Custom Preset can be deleted To delete a setting drag the setting to the left andthen press the DELETE button for iOS For Android just hold the setting and then press Delete General Setting Vos App Version Pressing the Setting Button E on the Opening Page willtake you to the General Setting Page Followings can be done on this page Change Temperature Unit Celsius and Fahrenheit can be interchanged by pressing 1093 68 1503 1
Download Pdf Manuals
Related Search