VizAlert Radar Detector Interface - Valentine One
Contents
1. a YLI 1 WPACK Conients 1 x In line fuse unit 3 Amp 1 x POWERSENSEnode engine running sensor 1 x Power cable 1 x RADARnode wireless transmitter 1 x RDI software card for the V1 inserted in RADARnode 1 x Cheetah connector cable for the V1 1 x User manual Cheetah parts are pre connected for your convenience Our 2 pin mini connectors push fit together and lock securely To unclip press the lever down and gently pull them apart The RADARnode is a wireless transmitter 433 Mhz that connects up to your radar detector s power supply socket When your radar detector gives an alert the RADARnode digitally analyzes the alert data and transmits a radio code to your helmet display The small flying lead with half a bullet connector at the end plastic sheathed is an over ride cable for connecting to a Cheetah Laser Jammer Interface in motorcycle installations The POWERSENSEnode is a clever engine running sen sor that turns on power when you start up your motorcycle and turns it off when you stop the engine It s an instant ignition switched supply that makes it quick and easy for anyone to create a safe power supply directly from the battery terminals It eliminates the need for direct wiring into your bike s electrical system pamasa S YHU y puepoog py saiBbojouyse peoueapy Yye eeYD 6007 uoleJado pasisapun asneo Aew Jey SOUdJaJJ9 UI Bulpnjoul penisoes BoUeJELE UI Aue d2. IMPORTANT If you add in a Valentine Concealed Display or a Valentine Remote Audio Adapter this standard pack does not enable these Valentine remote displays to function correctly To make them work you can purchase an extra component called the Cheetah V1 Remote Adapter from our website at www SpeedCheetah com and click on motorcycle products in the main menu RADARnode Cheetah RDI connector cable must be inserted the correct way round DETECTOR Power The radar detector and VizAlert display work independently The POWERnode attached to the battery will automatically turn on the power to the RADARnode transmitter and radar detector when you start your motorcycle s engine It will remain on for as long as the engine is running The VizAlert s battery pack has a sliding ON OFF switch All 6 LEDs will flash once at the same time to confirm it is switched on When you power up your detector the transmit ter will begin to transmit to the VizAlert helmet receiver The VizAlert LED s will flash in a circular sequence when the wireless link has been established 4 2 Testing your system Press and release the test button on the side of the RADAR node The VizAlert will flash each LED in sequence Remember your engine must be running for the transmitter and detector to be powered up 4 3 Alerts Please refer to the VizAlert Display manual for interpreting alerts Ku band users Europe If Ku band is enabled
3. always be positioned in the seat cavity 2 1 The Cheetah connector cable for the V1 must be installed the correct way round Each end of the cable is labeled If the cable is inserted the wrong way round it will not work Plug the end labelled V1 into your Valentine detector 2 2 Safely route the RDI connector cable from your V1 to the RADARnode transmitter underneath the motorcycle seat Secure the Cheetah cable to the bike wherever possible avoiding contact with any high temperature engine compo nents or the exhaust system 2 3 Plug it into the RADARnode socket marked DETECTOR 2 4 Double check that the RDI software card and connector cable are specific to your radar detector The RDI software card is pre installed in the side of the RADARnode transmit ter Always ensure that the power is OFF before remov ing or inserting your RDI software card 2 5 Connect the POWERSENSEnode and fuse pack directly to the battery terminals RED is positive BLACK is negative There is no need to remove the leads from the battery Just loosen the nut on the clamp slide in the spade terminal and re tighten the nut 2 6 Finally plug the power cable into the RADARnode socket marked POWER 2 7 OPTIONAL laser jammer installations only Connect the small flying lead with the bullet connector to the similar over ride cable on the Cheetah LASERnode SHOCIUNG UP VOUT VAVENUTE T V1 menu items can be set according to personal preference
4. ave snu 3149 p SIY Z pue S9OUdJEJJE U NJUeY asneo 9 you Aew 214 p siy suogipuoo om HUIMO O BU 0 pp fqns s UOHeJBdO s NnyY DOA OY JO GL Hed YM s do 3919P SIUL F S G6G ANOeJIG JO SUOISIAOJd JUeAgjal JayjO pue syu w nb s jeu ss y UM sdUel dWOD ul SI yONpoJd si ey saJejpap py seiBojouyos pavueapy yeyo woo yejaayjpaeds Myploddns iews se jd u nz joNpoud e sHuewe 0 JO 1SsISJed sw jqosd Aue J LUO Ye OsUDPsedS MMM IISIA PLIOAA JO SOY 99 doing WU09 J0JDBI9PS gH MMM IISIA EPeULRD YB WSN UO Bbed SdDIAJOS JOWOISND JNO yOsUD se jd ine e sdoj n p yOnpoud Yyelesyy JNOA uosess Aue JO yioddns 9 adIAIaS wood yeJaayjpseds mum JE OUI UO BIGe IEAe SUOIIDUOD pue swa AJUeBLeEM N4 eseyoind euio y Jo ep y wo Je DUO JO poled e JO diysuewyJom pue sjenazew Ul S 9949p je sSulebe s onpoud Jno jueweM py saibojouyoe peoueApy yejeeuD AueemM poywi7y wos yejaayapa ds mmm je sul UuO Ja sIBay uoljeijsibay Ajuee A HOWUNSS AMEE The RADARnode Transmitter Over ride cable for Cheetah LASERnode Test button Power socket RDI Software card Detector socket Cheeta nallar In line fuse unit with POWERSENSEnode battery connections POWER IN IL a Jammer over ride Instal the RADARnode according to the diagram above Please note that the RADARnode transmitter is not water proof so should
5. please note the V1 uses the same audio tone for K and Ku bands The RADARnode will copy this and transmit a K band warning for both K and Ku alerts so the VizAlert display will flash white for both K and Ku bands 4 4 Switching off your system When you switch off your engine power to the RADARnode transmitter and radar detector is automatically switched off The VizAlert is motion sensitive and switches off after 10 minutes of no movement The VizAlert V2 s battery pack has a sliding ON OFF switch and an automatic shut off function if you leave it on by accident OW FOUNIESHOOUING Constant KU Band radar alert RDI software card is not correctly installed It must be fully inserted into the slot on the side of the RADARnode Switch off power then remove the card and re insert flush Always ensure that the power is OFF before removing or insert ing your RDI software card
Download Pdf Manuals
Related Search