Highlite Cine 260 GETTING STARTED
Contents
1. Highlite Cine 260 mum PROJECTION GETTING STARTED Getting to know the projector Notes gt For complete and detailed information about how to use and control the projector see the User Manual Wh Front Infra red window Adjustable remote control feet Air inlet Lens Projector Remote control reception Remote panel angle control T 40 Air inlet Input connections Air outlet s Power am connection Rear Infra red window remote control Rev A December 2010 111 370A Getting Started Positioning the screen and projector e Install the screen ensuring that it is in the best position for viewing by your audience e Mount the projector ensuring that it is at a suitable distance from the screen for the image to fill the screen and that it is perpendicular to the sceen Switching the projector on e Connect the power cable between the mains supply and the projector Switch on at the switch next to the power connector Wait until the self test has completed and the standby indicator on the projector control panel shows amber The lamp will be off and the projector will be in STANDBY mode Projector control panel Power connection e Press POWER ON 1 on the remote control or POWER C on the projector control panel to switch the projector ON The power indicator on the control panel will flash blue for approximately 30 seconds whilst the lamp comes up to full brightness Whe2. control or by pressing the SOURCE button on the projector control panel until the correct signal is displayed Test pattern If you have no video source connected to the projector then you can display a test pattern as follows e Press on the remote control until the desired test pattern is displayed Adjusting the lens e Press the key repeatedly to cycle through the Lens adjustments in the following order Focus Zoom Shift e Use the use the A AA Eu and p keys to adjust the lens Example Lens Shift control Rev A December 2010 Getting Started Notes IS For more information about connecting input signals see Signal Inputs in section 2 of the User Manual Installation For more detailed information about input connections see Input signals in section 6 of the User Manual Controlling the projector For more information about lens Shift see Shifting the image in section 2 of the User Manual Installation Page 3 Getting Started Digital Projection Highlite Cine 260 Adjusting the projected image Notes Aspect ratio p gt For more detailed information e Press on the remote control until the image is displayed in the corect aspect about ratio using all the control keys on the remote control or the Image quality settings projector control panel e Press any of the following keys on the remote control followed by A and Ea to adjust these image quality setting
3. n the projector is ready for use the power indicator will show a steady blue Inserting batteries into the remote control e Open the battery compartment and insert two AA size batteries making sure they are inserted the correct way round as shown below Page 2 Digital Projection Highlite Cine 260 Notes IS For more information about positioning the screen and projector see Positioning the screen and projector in section 2 of the User Manual Installation For more detailed information about using the control keys on the remote control or the projector control panel using the menus see section 4 of the User Manual Controlling the projector If the red ISSUE indicator is illuminated continuously or flashing see Error Codes in section 6 of the User Manual Appendix for more information Do not mix an old battery with a new one or different types of batteries If you will not use the remote control for a long time remove the batteries to avoid damage from battery leakage Rev A December 2010 Digital Projection Highlite Cine 260 Selecting an input signal or test pattern Input e Connect an video source to the projector The signal should be automatically detected by the projector and should be displayed within a two or three seconds e If more than one signal is connected to the projector then select which signal is to be displayed using the a1 to buttons on the remote
4. s l 7 see section 4 of the User Brightness Manual Controlling the rojector Contrast Sharpness using the menus For the picture setting adjustments shown here after 5 seconds if no adjustment has been made the indicator will go out and the adjustment key must be pressed again to end the adjustment before 5 seconds has elapsed press a different adjustment key or press the key again Switching the projector off e Press POWER OFF on the remote control or POWER 5 on the projector control panel then press the button a second time to confirm your Always allow the lamp to cool intention to switch off for 5 minutes before disconnecting the power moving the projector changing the lamp e Wait until the power indicator has switched off and the standby indicator on the Cleaning the fans and filter projector control panel shows amber The projector will now be in STANDBY mode The lamp will switch off and the power indicator on the control panel will flash blue for approximately 30 seconds until the lamp has cooled down e Switch off the power switch next to the power connection then disconnect the power cable from the projector Page 4 Rev A December 2010
Download Pdf Manuals
Related Search