ASI-8910_En SIGMA.cdr
Contents
1. again If the passwords in put are inconsistent the buzzer will innitiate two short buzzing and exit the Editing Mode 5 3 Change user password Finish the procedures in 5 1 O Dial 1 1 in put a 4 digit new password O Dial 1 rein put the new password O Dial again 5 4 Adding card information 5 4 1 Adding a single card Valid Card Password Input Long buzzing once Invalid Card Input Short buzzing twice Invalid Password Input Short buzzing twice Press Exit Button Long buzzing once Correct Input Long buzzing once Incorrect Input Short buzzing twice Anti disassemble Alarm Continuous buzzing Card Overflow Short buzzing twice Deleted or Invalid Card Short buzzing twice Buzzer Anti dis assemble Button Sustained Effort for the Better2. Za SILMA inteoral Integrated Access Control System 3 Ensure power cable is ready before put the system on screw bolt from bottom Finish the procedures in 5 1 O Dial 2 input the 3 digit number of the card for example 033 256 etc read the card O dial again 5 4 2 Adding multiple cards Finish the procedures in 5 1 O Dial 2 input the 3 digit number of the first card O read the second card for example read 10 cards at one time O dial again one 3 digit number corresponds to one card In case of adding multiple cards the 3 digit number for the se cond card will add 1 automatically the number ranges from 000 799 5 5 Deletion of card after finish the procedures in 5 1 Dial 5 5 1 Delete all cards Dial 3 1 input 0000 dial 5 5 2 Delete the cards read Dial 3 read the card O dial 5 5 3 Delete lost card Dial 3 O input the num ber of the lost card dial 5 6 Door open mode setup after finish the proce dures in 5 1 5 6 1 Open with card Dial 400 O0 dial 5 6 2 Open with card and password Dial 401 dial 1 Product Features 1 1 Independent and concise configura
3. 5 dial a 2 digit number 00 99 O0 dial The default door open time is 3 seconds 5 8 anti disassemble alarm setup Finish the procedures in 5 1 O Dial 600 dial close anti disassemble alarm output dial 601 0 dial permit anti disassemble alarm Default setup forbid the anti disassemble alarm 5 9 Reset administrator password In case the newly assigned administrator pass word is lost the following procedures can be carried out to recover the default password from factory i e 123456 5 9 1 Switch off the power and uninstall the device 5 9 2 Switch on the power again and connect No 1 and No 4 finger On Jp2 which is located on the back circuit board of the device Please note only connect No 1 and No 4 Not No 1 No 2 No 3 and No 4 Jp2 locate at the bottom of the circuit board and can be seen and operated without opening the back cover 3 Installation Procedures 1 Disassemble the back cover Uncover the back from bottom N Back of Controller GND 12V COM NO NC GND SW BELL O O 0 O O O O O O O SIAE EIE EIA KSE CS O C Exit Button EM Lock V NO COM Special Note 1 T
4. ble by the panel without connecting to computer 1 2 Three modes of access Card alone Card plus Password and Password alone 1 3 Facilitated with a capacity of 800 cards with one password 1 4 Supportive for disassemble preventative alarm 1 5 Exit button input and door bell input 1 6 All data can be kept for 10 years with power off 1 7 Input with wave absorption function 1 8 Supportive for electronic locks working in power on mode or power off mode 1 9 Product Size LxWxH mm 117 117 21 2 Electric Parameters Working Voltage DC9 15V Static Current s70mMA Lock Current s3000mA Reader Distance 5 15 cm Type of Card EM card or compatiable EM Card Working Temperature 101 to 50 Relative Humidity 10 90 4 Wiring Diagram AC 220V 50Hz E n O BHIJIJAB O AC220V Controller Power Note A N Disconnect all powers before AN wiring the po wer can be swi tched on with all components are connected correctly B B 12VGND 12 GND O m XO KJ 0 O 5 6 3 Open with card or password Dial 402 dial Default is 402 open with card or password 5 Door open time setup Finish the procedures in 5 1 O Dial
5. he interval of each operation is 15s while the in terval of each key push is 3s 2 Password consists of numbers from 0 to 9 3 Each operation should be ended by 6 Instruction for LED Lights Type of Alarm Red Green Orange POWER OK MODE Normal Mode On Off Off Configuration Mode Off Off On Valid Card Password Off On Off Invalid Card On Off Off Invalid Password On Off Off Press Exit Button Off On Off Correct Input Off Off On Incorrect Input On Off Off Disassemble Alarm On Off Off 7 Instruction for Buzzer Type of Occasion Mode of Buzzer Normal Mode No buzzing Entering Configuration Mode Long buzzing once 2 Put the back cover agianst wall and screw tight the bolts PA WA g He g Ty KS OSS AE Ay N A 5 Configuration The default administrator password is 123456 defualt user password is 8888 5 1 Entering configuration Dial and input administrator password then dial key If the password is correct the buzzer will innitiate one long buzz and the POWER light will be off while the MODE light on The buzzer will buzz twice shortly and the system will exit Editing Mode if the password is inccorrect 5 2 Change administrator password In the Editing Mode after finish the procedures in 5 1 Dial O O input a new 6 digit adminis trator password O Dial O reinput the new password Dial
Download Pdf Manuals
Related Search