Home

INNO SPOT PRO - Quality Music

image

Contents

1. User Instructions 10 13 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Inno Spot Pro General Information Unpacking Thank you for purchasing the Inno Spot Pro by ADJ Products LLC Every Inno Spot Pro has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If th
2. Screw one clamp via a M12 screw and nut onto the Omega holder Insert the quick lock fasteners of the Omega holder into the respective holes on the bottom of the Inno Spot Pro Tighten the quick lock fasteners fully clockwise Screw in the included Eye Hole screw to the base and pull the safety cable through the eye hole and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 6 Inno Spot Pro Set Up Power Supply The ADJ Inno Spot Pro contains a automatic volt age switch which will auto sense the voltage when it is plugged into a power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures
3. 1 Tap the MENU button until Reset is displayed press ENTER 2 The fixture will now reset ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 15 Inno Spot Pro System Menu 127 Pan offset Ho 127 a 127 127 127 Tilt offset Color offset x 127 127 MENU Gobol offset 2 127 RGobol offset i 127 Prism offset 255 127 RPrism offset 12 0 ba Focus offset 255 To enter the OTIL Home position adjustment amp Gobo wheel adjust ment submenu press the ENTER button for at least 3 seconds In this submenu you are able to adjust the home position of the pan tilt color wheel gobo wheel RGobo Rotating wheel prism RPrism and focus position Pan Offset Adjustment of the pan home position 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Pan Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Tilt Offset Adjustment of the tilt home position 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Tilt Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press EN
4. the main power before attempting to change the gobos 1 To change the gobo you must remove the top half of the moving head The top half of the moving head does not have the lens attached to it 2 Unscrew the 4 phillips screws that secure the top half of the head Remove the top half of the head 3 When you remove the shell you will be able to access the gobo wheel see picture below Rotate the head so that the lens is aimed up Turn the gobo wheel with your hand until you find the gobo you would like to change 4 Using a pair of needle nose pliers grab the fixture ring that holds the gobo in place and remove the ring 5 Once the ring is removed rotate the head upside down so that the gobo falls into your hand 6 Carefully insert your new gobo and insert the fixture ring 7 Reassemble the unit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 24 Inno Spot Pro Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Inno Spot Pro Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried o
5. 11 5 L x 6 75 W x 16 75 H 288mm x 167mm x 425mm 10 Lbs 9 kgs Dimensions Weight Beam Angle 12 17 Degrees Fuse 1 Amp Duty Cycle None DMX 14 DMX Channels Colors 8 White Gobos 6 Spot 24mm 0 2mm thickness Metal Gobo 1 1mm thickness Glass Gobo 20mm viewable Any Safe Secure Position 3 Year 1095 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice Working Position Warranty ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 te 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On facebook com americandj twitter com americandj youtube com adjlighting
6. for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instru ment is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prio
7. MENU button until Slave Mode is displayed ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 11 Inno Spot Pro System Menu press ENTER Either Slave 1 or Slave 2 will be displayed 2 Press the UP or DOWN buttons until your desired slave mode is displayed press ENTER to confim NOTE In a Master Slave configuration you can make one fixture the Master and then set the next fixture to Slave 2 the fixtures will now have contrast movement to each other Black Out This will control blackout 1 Press the MENU button until Black Out is displayed press ENTER 2 Either Yes or No will now be displayed Press the UP or DOWN buttons to toggle between Yes and No 3 Press ENTER to confirm your setting Sound State In this mode the unit will run in sound active mode 1 Press the MENU button until Sound State is displayed press ENTER 2 Either On or Off will now be displayed Use the UP or DOWN buttons to toggle between On and Off 3 Press ENTER to confirm your selection the press and hold the MENU button to activate Sound Sense In this mode you can adjust the sound sensitivity of the sound active mode 1 Press the MENU button until Sound Sense is displayed press ENTER 2 Press the UP or DOWN buttons to adjust the sensitivity level The sensitivity level can be adjusted between 0 the lowest and ADJ P
8. SM EFFECT g PRISM ROTATION Boonen lt 0 127 JCOUNTER CLOCKWISE INDEX 0 360 128 189 COUNTER CLOCKWISE FAST SLOW 190 193 STOP 194 255 CLOCKWISE SLOW FAST ee UTZ O 255 ZOOM OUT ZOOM IN Distance m 0 SHUTTER STROBE 0 7 BLACKOUT 8 15 SHUTTER OPEN 16 131 STROBING SLOW FAST 132 139 SHUTTER OPEN 140 181 SHUTTER SLOW OPEN FAST CLOSE 182 189 SHUTTER OPEN ME 190 231 SHUTTER SLOW CLOSE FAST OPEN 232 239 SHUTTER OPEN 240 247 RANDOM STROBE 248 255 SHUTTER OPEN BLACKOUT RESET 0 69 NOTHING 70 79 BLACKOUT W PAN TILT MOVEMENT 80 89 NO BLACKOUT PAN TILT MOVEMENT 90 99 BLACKOUT W COLOR CHANGE 100 109 NO BLACKOUT W COLOR CHANGE 110 119 BLACKOUT W GOBO CHANGE 120 129 NO BLACKOUT W GOBO CHANGE 130 199 NOTHING Inno Spot Pro 14 200 209 210 255 DMX Traits Function BLACKOUT RESET RESET ALL NOTHING Photometric Chart 87640 22330 5834 3700 2529 Lux 30900 10920 4916 2805 1788 Lux a ms ea HS E IS ES nas mn us EOS E E IO VE O IE E IS A SS VES O IO IO E ES E E E O A PU VERA VE VS VO HE 1 0 ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 22 ADJ Products LLC 2 0 www adj com 3 0 4 0 5 0 Inno Spot Prolnstruction Manual Page 23 Inno Spot Pro Gobo Replacement This unit comes with interchangable gobos When changing the gobos please be very careful Caution Never open the unit when in use Always disconnect
9. System Menu 1 Press the MENU button until Dimmer Calibrat is displayed press ENTER 2 A number between 50 100 will be displayed This number rep resents the instensity setting Use the UP or DOWN buttons to adjust the LED output intensity 50 being medium intensity and 100 being full intensity 3 When you have found your desired setting press ENTER to confirm Auto Test This function will run a self test program 1 Press the MENU button until Auto Test is displayed press ENTER 2 The fixture will now run a self test Press the MENU button to exit Temp With this function you can display the running temperature of the unit 1 Tap the MENU button until Temp is displayed press ENTER 2 The current running temperature of the fixture will now be displayed Press MENU to exit Fixture Time with this function you can display the running time of the unit 1 Tap the MENU button until Fixture Time is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 14 Inno Spot Pro System Menu Fixture Version This will display the software version 1 Tap the MENU button until Fixture Version is displayed Press the ENTER button and the software vesion will be displayed 2 Press the MENU button to leave this function Reset Use this function to reset the unit
10. TER to confirm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 16 Inno Spot Pro System Menu Color Offset Home setting adjustment for the color wheel 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Color Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Gobo Offset Home setting adjustment for the gobo wheel 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Gobo Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit RGobo Offset Home setting adjustment for the rotating gobo 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that RGobo Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Prism Offset Home setting adjustment for the prism 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Prism Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to conf
11. and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Inno Spot Pro can be controlled via DMX 512 proto col The Inno Spot Pro is a 14 channel DMX unit The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX control ler require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and E lighting stores Your cables should be made with Figure 1 ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 7 Inno Spot Pro Set Up a male and female XLR connector on either end of the cable Al
12. anual Page 10 DMX Address Set the DMX Address 1 Press the MENU button until DMX Addresss is displayed press ENTER 2 X will now be displayed X represents the displayed address Press the UP or DOWN buttons to find your desired address 3 Press ENTER to confirm and then press and hold the MENU button for at least three seconds to assign Show Mode Show modes 1 4 Factory Shows 1 Press the MENU button until Show Mode is displayed press ENTER 2 Show X will now be displayed X representing a number between 1 4 Press the UP or DOWN buttons to find your desired show and press ENTER to confirm After pressing ENTER press and hold the MENU button for at least 3 seconds to activate SHOWS Show 1 For fixtures placed on the floor the tilt movement angle is 210 Show 2 For fixtures fixed to the ceiling or truss the tilt movement angle is 90 Show 3 For fixtures placed on a table or stage The beam is pro jected at the audience s direction i e in front of the stage Pan move ment angle left to right to left is 160 Tilt movement angle is 90 Show 4 For fixtures fixed to the ceiling or truss The beam is pro jected at the audience s direction i e in front of the stage Pan move ment angle left to right to left is 160 Tilt movement angle is 90 Slave Mode This will let you set unit as a slave ina master slave configuration 1 Press the
13. arranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty L E D Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 26 Inno Spot Pro Specifications Model Inno Spot Pro Voltage 100 240V 50 60Hz LED 1 x 60W White LED Power Consumption 140W 110V 134W 220V Power Cord Daisy Chain 4 Fixtures Max 120V 8 Fixtures Max 220V
14. e carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Inno Spot Pro is a 14 channel DMX intelligent moving head LED fixture The Inno Spot Pro can operate as a stand alone fixture or in a Master Slave configuration The Inno Spot Pro has three operating modes a sound active show mode DMX controlled This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support adj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all
15. gure 4 ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 8 Inno Spot Pro Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 Pin 3 Not Used Not Used PA Pin 4 Do Not Use Pin 5 Do Not Use ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 9 Inno Spot Pro System Menu 001 DMX Address 512 Show 1 Show 2 Show Mode Show 3 Show 4 Sl 1 Slave Mode i 2E Yes n D lt N Black Out No Sound State On Off 0 Sound Sense 100 Pan Inverse gt Yes Tilt Inverse i No MENU Back Light Focus Adjust 255 50 Dimmer Calibrat 100 Auto Test Temp Fixture Time Fixture Version Reset ADJ Products LLC www adj com Inno Spot Prolnstruction M
16. irm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 17 Inno Spot Pro System Menu RPrism Offset Home setting adjustment for the rotating prism 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that RPrism Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Focus Offset Home setting adjustment for the focus 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that focus is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 18 Inno Spot Pro Operation Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The fir
17. lled person once a year the electrical cord This prong is used to reduce the risk of electrical is jl shock and fire in case of an internal short A LP Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 25 for cleaning details S e Heat This fixture should be sit
18. no Spot Pro Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 4 fixtures max 120V and 8 fixtures max 220V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures Inno Spot Pro UC3 Control The optional UC3 Controller not included may be used to con trol different functions including blackout Stand By Blackout the unit Function 1 Sync Strobe Show 1 Select Color 2 Async strobe 1 4 2 Select Gobo 3 Sound Strobe Mode Sound LED OFF Show LED LED ON Slow Blinking GOBO WHEEL 0 9 SPOT 10 18 GOBO 1 19 27 GOBO 2 28 36 GOBO 3 37 45 GOBO 4 46 54 GOBO 5 55 63 GOBO 6 64 73 SPOT SHAKE 74 82 GOBO 1 SHAKE 83 91 GOBO 2 SHAKE 92 100 GOBO 3 SHAKE 101 109 GOBO 4 SHAKE 110 118 GOBO 5 SHAKE 119 127 GOBO 6 SHAKE 128 189 GOBO WHEEL ROTATION SLOW FAST 190 193 STOP 194 255 GOBO WHEEL ROTATION FAST SLOW ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 20 ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 21 Inno Spot Pro DMX Traits Function GOBO ROTATION 0 127 COUNTER CLOCKWISE INDEX 0 360 128 189 CLOCKWISE FAST SLOW 190 193 STOP 194 255 COUNTER CLOCKWISE SLOW FAST PRISM Inno Spot Pro NO EFFECT Beam angle 12 PRI
19. not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 3 Inno Spot Pro Safety Precautions Inno Spot Pro Installation For Your Own Personal Safety Please Read and Understand This When installing the unit the trussing or area of installation must be Manual Completely Before You Attempt To Install Or Operate able to hold 10 times the weight without any deformation When This Unit installing the unit must be secured with a secondary safety attach To reduce the risk of electrical shock or fire do not expose this unit ment e g and appropriate safety cable Never stand directly below rain or moisture the unit when mounting removing or servicing the unit Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from These installaiton should be checked by a ski
20. r written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including w
21. roducts LLC www adj com Inno Spot Prolnstruction Manual Page 12 Inno Spot Pro System Menu 100 most sensitive 3 Press ENTER to set you desired level Pan Inverse Pan Inversion 1 Press the MENU button until Pan Inverse is displayed press ENTER Either Yes or No will be displayed 2 To activate the Pan inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Pan inversion select No and press Enter Tilt Inverse Tilt Inversion 1 Press the MENU button until Tilt Inverse is displayed press ENTER Either Yes or No will be displayed 2 To activate the Tilt inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Tilt inversion select No and press Enter Back Light with this function you can make the back light automatically turn off after one minute 1 Press the MENU button until Back Light is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select ON to keep the backlight on at all times or OFF to allow the backlight to turn off after 2 minutes Press any button to turn the backlight on again 3 Press ENTER to confirm Dimmer Calibrat with this function you can set the output intensity ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 13 Inno Spot Pro
22. so remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 EE ON DO IS O SA A i XLR Male Socket XLR Female Socket i XLR Pin Configuration ee 2 Cold 2 Gold 1 Ground Pin 1 Ground Pin 2 Data Compliment negative I I 3 Hot 3 Hot i Pin 3 Data True positive Lae ee ee ee ee mm 4 Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference It is always advisable A p to connect a DMX terminal Resistanc 120 Ohm 1 4 W between PIN 2 DMX 2 and PIN 3 DMX of the last fixture Fi
23. st unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit find your desired show and set that show by pressing the ENTER button 3 On the slave units tap the MENU button until Slave Mode is displayed and Press ENTER Choose either Slave 1 or Slave 2 and press ENTER See pages 11 12 for more info 4 The slave units will now follow the Master unit Universal DMX Control This function allows you to use a Elation universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Inno Spot Pro is a 14 channel DMX fixture See pages 21 23 for detailed description of the DMX values and traits 2 To control your fixture in DMX mode follow the set up procedures on pages 5 7 as well as the set up specifications that are includ ed with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instruction on page 11 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture 7 For help operating in DMX mode consult the manual included with your DMX controller 415 Sound Active Mode This mode allo
24. times ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 2 Inno Spot Pro General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Inno Spot Pro Features e DMX 512 Protocol Compatible 14 DMX Channels 8 Colors White 6 Rotating Replaceable Gobos Spot 3 Operating Modes Sound Active Show Mode amp DMX Control Power Cord Daisy Chain See page 20 for more info Internal Microphone Digital Display for Address and Function Setting UC3 Controller Not Included 4 Preprogrammed Shows Inno Spot Pro Warranty Registration The Inno Spot Pro carries a 3 year 1095 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj products com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Inno Spot Pro Handling Precautions Caution There are no user serviceable parts inside this unit Do
25. uated away from heat sources such The Inno Spot Pro is fully operational in two different mounting posi as radiators heat registers stoves or other appliances including tions hanging upside down from a ceiling or set on a flat level sur amplifiers that produce heat face To avoid internal damage to the unit never mount the unit on The fixture should be serviced by qualified service personnel when its side as illustrated above Be sure this fixture is kept at least 0 5m A Objects have fallen or liquid has been spilled into the appliance away from any flammable materials decoration etc Always use B The appliance has been exposed to rain or water and install the supplied safety cable as a safety measure to prevent C The appliance does not appear to operate normally or exhibits accidental damage and or injury in the event the clamp fails see next a marked change in performance page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 4 ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 5 Inno Spot Pro Installation NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life
26. ut periodically to optimize light output Cleaning frequency depends on the environ ment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Inno Spot Pro Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the rear panel of the unit 2 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 25 Inno Spot Pro Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship
27. ws either single unit or several units linked together to run to the beat of the music 1 Press the MENU button until Sound State is displayed and ADJ Products LLC www adj com Inno Spot Prolnstruction Manual Page 19 Inno Spot Pro Operation Inno Spot Pro DMX Traits press ENTER Tap the UP or DOWN buttons so that ON is dis Function 0 255 2 To adjust the sound sensitivity press MENU button until Sound 1 Sense is displayed and press ENTER 2 PAN FINE 3 Use the UP and DOWN buttons to adjust the sensitivity and 3 press ENTER when you have found your desired sensitivity level 4 TILT FINE 4 The optional UC3 Controller not included may be used to con 5 a 4 COLORS 0 7 WHITE 8 14 RED 15 21 ORANGE 22 28 YELLOW 29 35 GREEN 36 42 BLUE 43 49 PURPLE 50 56 LIGHT BLUE 57 63 PINK 64 127 COLOR MIXING 128 189 CLOCKWISE ROTATION FAST SLOW 190 193 STOP 194 255 COUNTER CLOCKWISE ROTATION SLOW FAST played and press ENTER trol different functions including blackout Show Mode This mode allows either a single unit or several units linked together to run one of four shows that you choose 1 Press the MENU button until Show Mode is displayed and press ENTER Press the UP or DOWN buttons until you find your desired show and press ENTER The optional UC3 Controller not included may be used to con trol different functions including blackout Nh ES In

Download Pdf Manuals

image

Related Search

Related Contents

Réfrigérateur  Precharge / Discharge Controller User's Manual    Betriebsanleitung für Pumpensteuerungsmodule  Operating instructions for Redox  Impressora Xerox® D110/D125/D136  Electrolux 66300KF-an Cooktop User Manual  la montre GPS de running qui rend les kilomètres plus faciles  DÉCOUVREZ  Sanyo HT27745 User's Manual  

Copyright © All rights reserved.
Failed to retrieve file