SF-100 User`s Manual
Contents
1. Place the LS 1000 on its side with the film slot toward the top The on off switch will be on the uppermost side Open the connector cover on the front panel and slide the cover into the panel Step 2 Raise the binder by pressing the end above the magazine cover Connector Cover Binder 11 Step 3 Place the SF 100 in front of the LS 1000 and insert the SF 100 connector fully into the LS 1000 connector Step 4 Press the binder to be engaged with the groove on the top of the LS 1000 to fix the feeder to the LS 1000 Make sure that the lock is fully engaged the surface of the lock should be perfectly horizontal Do not lift or move the scanner with the feeder attached Always detach the feeder before the scanner is moved 12 4 2 Setting Mounted Slides Set the slides to be read by LS 1000 in the insertion side of the magazine Step 1 Open the magazine cover Step 2 Next grip the slide push plate in the insertion side with your fingers pull it back against the spring and catch it in the notch so that it cannot return to its original position Note Make sure that the slides are inserted with the emulsion surface rough surface toward the slide push plate Ejection Magazine Insertion Magazine Magazine Cover Insert Guide Stickers 13 Note Make sure that the slides are inserted with the longer sides of the film at the top and bottom Inserting the slide with the shorter2. SF 100 1 SF 100 user s manual 1 Viewed from above The following kinds of slide mounts should not be used as they may cause a mount jam or prevent proper reading of the image Warped slide mounts Slide mounts with peeling or burred edges Slide mounts with a sticker or label affixed Slide mounts with sharp corners 9 2 4 Cleaning the Unit When carrying out routine maintenance and cleaning ensure that no volatile liquids such as alcohol benzine or thinner come into contact with the SF 100 as this may cause a failure fire or electric shock Please observe the following points Before cleaning always turn the power off and pull out the power plug Since the cover is made from plastic material remove dust with a blower or a dry cloth Use a soft dry cloth to remove dust from the metal panel at the rear If the unit has become badly soiled clean with a cloth moistened with neutral liquid detergent then dry with a dry cloth Avoid harsh substances such as alcohol benzine thinner or pesticides as they may damage the surface or remove the exterior finish 3 Parts Identification Display LED Magazine Cover Binder Ejection Magazine Insertion Magazine Slide Push Plate Slide Push Plate Insert Guide Stickers 10 4 Operation of the SF 100 4 1 Mounting on the LS 1000 Before connecting confirm that the LS 1000 is turned off Step 1
3. 1 User s Manual Auto Slide Feeder SF 100 Contents 1 Overview 1 1 Features 1 2 Operating Environment 2 Before Operation 2 1 Inspection 2 2 Accessories 2 3 Notes on Use 2 4 Cleaning the Unit 3 Parts Identification 4 Operation of the SF 100 4 1 Mounting on the LS 1000 4 2 Setting Mounted Slides 4 3 Removing Mounted Slides 4 4 Removing the Auto Slide Feeder 4 5 What to Do If a Mounted Slide is Jammed Appendix Specifications Index 2 Cautions The reproduction of all or part of this manual without our permission is prohibited The information contained in this manual is subject to change without notice We have made every effort to produce a perfect manual but should you find any mistakes we would be grateful if you would kindly let us know We shall take no responsibility for consequences resulting from the operation of this product despite the terms mentioned above Trademark Information Macintosh is a registered trademark of Apple Computer Inc Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation IBM PC AT is a trademark of International Business Machines Corporation Other brand or product names are the trademarks or registered trademarks of their respective holders Indication The indications in this manual signify important safety precautions In order to use this product safely please read every section where
4. these indications are placed before beginning operation this product These indications are also placed in the table of contents so users can find them easily Indication The indications in this manual signify the need for caution when using the products These indications are placed in sections that should be read by users before beginning operation in order to avoid damage to the product 3 Federal Communications Commission FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to
5. which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTIONS Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user s authority to operate the equipment Notice for customers in Canada CAUTION This class B digital apparatus meets all requirements of the Canadian interference Causing Equipment Regulations ATTENTION Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Notice for customers in European countries ACHTUNG Dieses Ger t entspricht den Bestimmungen der EG Direktive 87 308 EEC zur St rungsunterdr ckung L rmemission kleiner 70 dBA 4 If You Notice Anything Abnormal If unusual noise odor or smoke occurs switch the LS 1000 off immediately and disconnect the power cord and the SCSI cable Contact your retailer or Nikon sales representative in your country Storage and Operating Locations Proper storage will ensure the long life of the Unit In order to avoid internal dust while being stored it is recommended that an appropriate cover be used on the Unit Do not store or use where The temperature is above 95 F 35 C or below 50 F 10 C the temperature changes drastically or condensation occurs The humidity exceeds 80 The Unit is expose
6. ave extra space around and above the unit to ensure smooth operation Please refer to the drawing at right for the amount of space to be provided If possible place a suitable cover over the unit to avoid dust accumulating when it is stored The necessary space when the Auto Slide Feeder SF 100 is attached is shown below 2 5cm 2 5cm 6inches 15cm 4inches 10cm 23 6 60cm 8 2 Before Operation 2 1 Inspection Inspect the package to see whether any damage has occurred during shipment If there is any damage to the package please contact your retailer directly and do not unpack the unit 2 2 Accessories The following items are included with your SF 100 When you open the package check whether all the items are present If there are any missing items please contact your retailer immediately 2 3 Notes on Use Don t use a slide mount neither less than 1 1mm nor more than 3 0mm thick If the slide mount is not flat on its surface you may feel some roughness when mounting or unmounting the slide Don t force the slide mount into or out of the unit if it does not move smoothly When scanning a film don t touch or unmount the slide mount or strip film holder Keep the unit in a horizontal position Do not use slides with rounded mount edges as the feeding mechanism may not work properly with such slides
7. d to direct sunlight The atmosphere is excessively dusty The Unit may be subjected to excessive vibration or physical shocks The Unit is exposed to noise from other equipment nearby When Taking the Unit Out of The Country The use of this product may violate local laws and restrictions in some countries If this is the case we cannot bear any responsibility for any violations resulting from the use of this product 5 Notice concerning prohibition of copying or reproduction Note that simply being in possession of material which has been copied or reproduced by means of a scanner may be punishable by law Items prohibited by law from being copied or reproduced Do not copy or reproduce paper money coins securities government bonds or local government bonds even if such copies or reproductions are stamped Sample The copying or reproduction of paper money coins or securities which are circulated in a foreign country is prohibited The copying or reproduction of unused postage stamps or post cards issued by the government without obtaining approval from the government is prohibited The copying or reproduction of stamps issued by the government and certified documents stipulated by law is prohibited Cautions on certain copies and reproductions The government has issued cautions on copies or reproductions of securities issued by private companies shares bills checks gift cert
8. eference insertion ejection time Insertion approx 10 seconds Ejection approx 10 seconds Power source Supplied by LS 1000 DC 12V 350mA or lower DC 5V 30mA or lower Size 5 1 W x 7 8 D x 6 2 H inches 130 x 199 x 156 5mm Weight Approx 1 8 lbs 0 8kg Index A accessories 8 D display LED 9 E ejection Magazine 9 I insertion magazine 9 J jams clearing 17 M magazine cover 9 mounting the SF 100 on the LS 1000 10 O operating environment 7 P power source 18 R removing mounted slides 15 removing the auto slide feeder 16 S setting mounted slides 12 specifications 18 19 EC DECLARATION OF CONFORMITY We Name Nikon UK Limited Address Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK declare that the product Product Name Auto Slide Feeder SF 100 Manufacturer s Name Nikon Corporation Manufacturer s Address Fuji Bldg 2 3 Marunouchi 3 chome Chiyoda ku Tokyo 100 Japan is in conformity with the following Standards EN55022 Class B EN50082 1 IEC801 2 1991 4kV IEC801 3 1984 3V m IEC801 4 1988 1kV AC 0 5kV I O following the provisions of the EMC Directive 89 336 EEC DECLARATION DE CONFORMITE DE LA CEE Nous Nom Nikon UK Limited Adresse Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK d clarons que ce produit Nom du produit Passe Vues Automatique SF 100 Nom du fabricant Nikon Corporation Adresse du fabricant Fuji Bldg 2 3 Maruno
9. ificates etc commuter passes or coupon tickets except when a minimum of necessary copies are to be provided for business use by a company Also do not copy or reproduce passports issued by the government licenses issued by public agencies and private groups ID cards and tickets such as passes and meal coupons Comply with copyright notices The copying or reproduction of works such as books music paintings woodcut prints maps drawings movies and photographs which are copyrighted creative works is prohibited except when it is done for personal use at home or for similar restricted and non commercial use 6 1 Overview Thank you for purchasing the NIKON Auto Slide Feeder for the 35mm Film Scanner LS 1000 This manual describes the procedures unpacking setting up and connecting the unit with emphasis on hardware use and cautions Please read this manual thoroughly to ensure proper operation of your scanner We hope that you will find this manual helpful 1 1 Features The SF 100 is an Auto Slide Feeder designed specifically for use with the NIKON 35mm Film Scanner LS 1000 It allows consecutive automatic scanning of mounted 35mm slides Enables consecutive scanning using the software provided with the LS 1000 Holds up to 72 1 1mm thick mounted slides Magazine space of 80mm Can be attached to the LS 1000 without using connecting cables 7 1 2 Operating Environment Le
10. sides at the top and bottom may result in damage to the film or mount Note Insert Guide Stickers shown below help you to insert slides correctly Insert Guide Stickers Magazine side Place the slides in the insertion side of the magazine Slides can be placed in the insertion side of the magazine up to the reference mark Remarks Do not insert slides beyond the reference mark as this may cause them to jam Reference Marks The slide push plate should be set to the locking position where the notch is given 14 Step 3 Set the slides with their apertures vertically oriented with respect to the LS 1000 and with the emulsion surface facing the slide push plate Remarks Do not set the auto slide feeder horizontally as this will prevent scanning of both ends of the film and may also cause the slides to jam inside the auto slide feeder Step 4 Disengage the slide push plate from the notch and release it gently so that it is pressing against the slides Close the cover 15 4 3 Removing Mounted Slides Once a slide has been scanned in the LS 1000 it will be ejected into the ejection side of the magazine Step 1 Grip the slide push plate which presses against the slides ejected from LS 1000 and pull it out against the spring Step 2 Remove the mounted slides Remarks If you continue scanning after the ejection side of the magazine is full of slides it may cause a slide jam Always remo
11. uchi 3 chome Chiyoda ku Tokyo 100 Japan est conforme aux normes suivantes EN55022 Classe B EN50082 1 IEC801 2 1991 4kV IEC801 3 1984 3V m IEC801 4 1988 1kV AC 0 5kV I O selon les dispositions de la directive de la CEE 89 336 EEC ERKL RUNG BER EG NORMENGERECHTHEIT Wir Name Nikon UK Limited Anschrift Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK erkl ren hiermit da das folgende Produkt Produktbezeichnung Automatische Diapositiv Zufuhr SF 100 Name des Herstellers Nikon Corporation Anschrift des Herstellers Fuji Bldg 2 3 Marunouchi 3 chome Chiyoda ku Tokyo 100 Japan den nachstehend aufgef hrten Normen gen gt EN55022 Klasse B EN50082 1 IEC801 2 1991 4kV IEC801 3 1984 3V m IEC801 4 1988 1kV AC 0 5kV I O und zwar gem den Bestimmungen der EMC Richtlinie 89 336 EEC Kingston UK June 30 1995 Place Date Signature Managing Director Lieu Date Signature Directeur g n ral Ort Datum Unterschrift Gesch ftsf hrer
12. ve slides promptly 16 4 4 Removing the Auto Slide Feeder To remove the auto slide feeder follow the installation steps in reverse Step 1 Confirm that the LS 1000 is turned off Step 2 Close the magazine cover Step 3 Press down the lock toward the auto slide feeder side disengaging it from the groove in the top of the LS 1000 Step 4 Remove the connector by sliding the auto slide feeder away from the LS 1000 17 4 5 What to Do If a Mounted Slide is Jammed If a slide is jammed inside the auto slide feeder remove it as described below What to do if a jam occurs 1 Open the magazine cover 2 Grip the mounted slide with your fingers or tweezers and remove from the magazine Be careful not to damage the slide or the SF 100 If a jam occurs between the slide autofeeder and the LS 1000 1 Switch the power off after terminating scan operation of the LS 1000 2 Remove the binder and remove the auto slide feeder from the LS 1000 3 Grip the jammed mounted slide with your fingers or tweezers from the slot in the LS 1000 or from the slide autofeeder Be careful not to damage the slide or the SF 100 18 Appendix Specifications Film used 35mm mounted slides of 1 1 3 0mm in thickness Maximum number of slides About 50 1 6mm thick mounted slides Magazine space approx 80mm Connection Directly connected to front panel connector of vertically installed LS 1000 R
Download Pdf Manuals
Related Search