S4 jr jr Zoom User Manual CE 0107.book
Contents
1. Lamp code Watts Volts Initial Lumen Colour temp Average rated life HPL 575 230 575 230 14 900 3 200 K 400 hours HPL 575 230X 575 230 11 780 3 050 K 1500 hours HPL 375 230 375 230 7 250 3 000 K 1000 hours HPL 575 240 575 240 14 900 3 050 K 400 hours HPL 575 240X 575 240 11 780 3 050 K 1500 hours HPL 375 240X 375 240 19 750 3 000 K 1000 hours Colour frame holder Retaining clip ra HR Figure 2 The colour frame holder is equipped with a spring loaded retaining clip that prevents colour frames and accessories from falling out See Figure 2 WARNING Make sure all colour frame accessories are locked in position with the retaining clip before hanging the Source Four jr jr Zoom CE Step 1 Release the retaining clip by pushing it sideways while gently pulling backwards Step2 Insert the colour frame Step 3 Lock the retaining clip by pushing sideways while gently pushing forward Note The performance of saturated colours may be less than desirable in any theatrical lighting luminaire For best results always use high quality colour media rated for high temperature use ETC s optional Conical Gel Extender part 7060A1048 will provide maximum colour media life Gel Extenders are not recommended for 70 and 90 lens tubes due2. WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Replace lens if they contain visible damage cracks or deep scratches that may impair their effectiveness Step 1 Remove the lens assembly See Source Four jr jr Zoom Assembly Guide for lens removal instructions Step 2 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 5096 5096 mixture of each can be used to clean the glass surface Step 3 Reinstall the lens assembly English Cleaning the reflector WARNING Unplug the fixture before attempting to clean the reflector WARNING Do not use ammonia based or other harsh commercial cleaners Clean reflector only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution To quickly clean the reflector and You may also wipe the reflector with a clean lint free cloth If either method is n
3. V Rheinland AG We Electronic Theatre Controls Europe Ltd declare under sole responsibility that the product Product name Source Four fixed focus luminaries Product type model S405 S410 S426 S450 S4jr26 S4jr36 Srjr50 Lot n a Batch Serial number n a Item numbers one of each model to which this declaration relates in conformity with the following standards EN60598 1 2000 Luminaires General requirements and tests EN60598 2 17 1990 Specification for luminaires for stage lighting television film and photographic studios outside and indoor equiv BS 4533 102 17 1990 following the provisions of EU LV Directive s 73 23 EEC London United Kingdom Mr Adam Bennette Place of issue Name of authorised person ud n 09 Ae Eo TO Date of issue signature of authorised person Electronic Theatre Controls Europe Ltd Registered office Unit 26 28 Victoria Industrial Estate Grant Thornton House Victoria Road London W3 6UU U K Melton St London NW1 28W England Telephone 44 0 20 896 1000 Registered in England No 3057796 Fax 44 0 20 896 2000 VAT No 6629487 90 English Source Four jr jr Zoom CE Guidelines The Source Four jr jr Zoom CE is intended for professional use only Read the entire User Guide before using equipment WARNING Please note the following safety precautions Do not mount the Source Four jr jr Zoom CE on or near a flammable surface e Use the S
4. SOURCE FOU Face Don CE User Manual Production Dates September 2004 Present Copyright 2008 Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7062M1210 06 01 Rev B Released June 2008 Picking 7062M1004 B Table of Contents Declaration of Conformity llle 1 Source Four jr jr Zoom CE Guidelines 0 005 2 Basic Assembly 2 25 eA ee oe ELLE 3 Luminaire information lllleille eee 3 Colour frame holder 0 0000 eee eese 4 Replacing the HPL lamp 000002e eee eeee 5 Centering lamp and adjusting the field 6 Focusing the beam 1 ess 6 Shaping the beam isses Reef hand gs 7 Adjusting the yoke position llle 8 Switching lens assemblies llle 9 Cleaning glass lens 0 0 0 eese 9 Cleaning the reflector 1 0 llli 10 Portable appliance test PAT 0000 eee ee eee 11 ETC Emphasis Expression Insight Imagine Focus Express Unison Obsession Il ETCNet2 EDMX Source Four Revolution Sensor and WYSILink are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries All other trademarks both marked and not marked are the property of their respective owners English Declaration of Conformity Sicherheit C C T
5. en Keep the luminaire at least 0 6 meters away from any lit surface Lighted objects at this distance or greater will not exceed 90 C temperature from projected light 2 Source Four jr jr Zoom CE User Manual English Basic Assembly C clamp mounting Yoke Pattern holder slot Lamp housing Drop in iris slot cover Color frame Ai retaining gel clip arre Gel frame Yoke locking knob Zoom rear focus knob Beam focus knob Zoom front focus Figure 1 WARNING Please note the following safety warnings before use Do not mount the luminaire on or near combustible surfaces Do not operate the luminaire without a lens installed Always hang the luminaire with the colour frame retaining clip in the locked position Luminaire information Wiring and power information A plug of at least 2 5 amp 220 240V rating should be attached to the luminaire s mains lead The wires in the mains lead are 1 55mm each and coloured in accordance with the following code Green and Yellow Earth Blue Neutral m rr Brown Live WARNING This luminaire must be earthed Current rating 120V 5 amp maximum 240V 2 5 amp maximum Operating frequency 50 60 Hz A English HPL lamp table CAUTION The Source Four jr is rated for 575w maximum lamp Do not use lamps other than the HPL in Source Four fixtures Use of lamps other than HPL or greater than 575w will void your warranty
6. ion Yoke locking knob Figure 9 Step 1 Remove the yoke locking knobs washers and hex bolts from either side of the luminaire Step 2 Raise or lower the luminaire to the desired position within the yoke Step 3 Reinstall the yoke s hex bolts washers and locking knobs Step 4 Tighten the yoke knobs to secure in position Setting the angle within the yoke Fi 1 Yoke locking knob igure 10 Step 1 Loosen the yoke locking knobs see Figure 10 Do not remove them Step 2 Tilt the luminaire to the desired position Step 3 Tighten the yoke locking knobs to secure in position 8 Source Four jr jr Zoom CE User Manual English Switching lens assemblies Follow these procedures to replace a fixed field lens with Zoom lens Lens tray Light baffle and retaining screw Figure 11 Step 1 Loosen the screw at the front of the baffle See Figure 11 Step 2 Pull the light baffle out of the barrel Step 3 Remove the beam focus knob from the bottom of the barrel and slide the lens assembly from the barrel Step 4 Slide the Zoom lens rear assembly into the barrel and install its beam focus knob Step 5 Slide the Zoom lens front assembly into the barrel and install its beam focus knob Step 6 Reinstall the light baffle and secure it with the retaining screw Note Reverse steps 1 6 to replace Zoom lens with a standard lens Cleaning glass lens
7. ot sufficient follow these steps Step 1 Step 2 Step 3 Step 4 Step 5 To protect the lamp housing during cleaning remove the lamp housing by loosening the knurled bolt and pulling the housing straight out See Figure 3 Remove the lens See Source Four jr jr Zoom Assembly Guide for full fixture disassembly assembly instructions Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 5096 5096 mixture of each can be used to clean the glass surface Reinstall the lamp housing and tighten the knurled bolt Reinstall the lens Source Four jr jr Zoom CE User Manual English Portable appliance test PAT The Portable Appliance Test is a set of tests that must be administered to electrical equipment in the UK and some locations in Europe to ensure safety The tests are typically carried out using a small PAT device The PAT device connects to a power source and then attaches to the product via an electrical outlet and test probes The PAT provides a simple pass or fail result allowing rapid testing of large inventories Source Four CE luminaires include a specific PAT point where the test clip is attached as shown in Figure 12 PAT tests should be performed by a qualified technician Your local regulatory authority has guidelines on the testing frequency PAT connection point Figure 12 English 12 This page intentionally left blank S
8. ource Four jr jr Zoom CE in dry locations only where humidity does not exceed 90 percent The luminaire is for indoor use only and is not intended for outdoor use e For temporary installations mount and support the Source Four jr jr Zoom CE only by the primary suspension yoke holes Suspend the luminaire from a hook clamp or a stand mount using a securely tightened steel bolt up to 12 mm flat washer and locking washer e In addition to primary suspension attach a safety cable ETC part 7060A1022 or chain to the secondary suspension point on the Source Four jr jr Zoom CE e Ifthe external cable is damaged it shall be replaced by ETC or our service agents Always hang the Source Four jr jr Zoom CE with the colour frame held securely behind the retaining clip Always replace the lamp if it becomes damaged or thermally deformed Disconnect the unit from power before all cleaning and maintenance The Source Four jr jr Zoom CE is suitable for indoor use with a maximum ambient temperature T 45 C e Maximum exterior surface temperature T 7235 C Amultilingual label sheet is included with this manual Affix the label of the appropriate language over the existing warning label on the extension yoke Do not cover ETC trademark or CE mark The Source Four jr jr Zoom CE contains a CE safety screen that covers the lens to prevent injury from broken glass due to lamp failure Do not remove the safety scre
9. ource Four jr jr Zoom CE User Manual English This page intentionally left blank QOO Corporate Headquarters 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 Fax 608 836 1736 London UK Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT a Via Ennio Quirino Visconti 11 00193 Rome Italy Tel 39 06 32 111 683 Fax 39 06 32 656 990 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 Fax 49 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 Fax 852 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com w Asia service etcasia com Web www etcconnect com w Copyright 2008 ETC All Rights Reserved m Product information and specifications subject to change 7062M1210 06 01 m Rev B m Released 06 2008
10. r knob clockwise to lock it in place Step 5 Finally turn the inner knob either clockwise or counterclockwise to achieve an optimum flat field See Figure 5 Focusing the beam p Beam focus knobs Figure 6 On a fixed field angle Source Four jr with a 26 36 or 50 lens adjust the lens single beam focus knob to focus the edge of the beam On a Source Four jr Zoom adjust the position of both lens Source Four jr jr Zoom CE User Manual English beam focus knobs to set the beam s spread and to focus the edge of the beam The Zoom lens provide a range from 25 to 50 Step 1 Loosen the beam focus knob s on the underside of the barrel as shown in Figure 6 Step 2 Slide the lens es forward or backward to achieve the desired beam edge Step 3 Once the luminaire is focused tighten the beam focus knob s Shaping the beam The beam can be shaped using the shutters see Figure 8 a pattern or an optional drop in iris Pattern Projection The pattern holder slot is on the top side of the barrel and in front of the shutters It accommodates an M size pattern holder see Figure 7 The pattern holder handle can be bent away from the shutter handle to keep it from interfering with the action of the shutter handle Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 6 35 cm to 6 98 cm 2 5 to 2 75 M Size Pattern holder Q Figure 7 D
11. ree cloth Allow to dry before operation Step 4 Align the flat sides of the lamp base with the retention brackets on either side of the socket as shown in Figure 3 English Step 5 Push down on the lamp base until the lamp seats firmly When properly installed the top of the lamp s base will be even with he top edges of the retention brackets A CAUTION Improperly installed lamps cause premature lamp failure and socket problems Step 6 Press lamp retaining clip across lamp base to secure Step 7 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt Centering lamp and adjusting the field Rear lamp housing Outer Knob lamp center adjustment Flat field best adjustment Inner Knob peak flat field adjustment Hot spot lamp pulled out too far Field with hole lamp pushed in too far Figure 4 Figure 5 The two concentric knobs located on the lamp housing allow you to align the lamp and adjust its field See Figure 4 The outer knob centers the lamp within the reflector The inner knob adjusts the lamp s field Step 1 Turn on the Source Four jr jr Zoom CE and aim it at a flat surface Adjust the barrel to create a hard edge Step 2 Unlock and loosen the outer knob by turning it counterclockwise Step 3 Gently move the outer knob from side to side and up and down until the lamp is centered within the reflector Step 4 Once the lamp is centered turn the oute
12. rop In Iris Slot Pattern holder slot Drop in iris slot Iris AM ike gio i dU 1 Y Shutters Figure 8 Will The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips screws prevents light leakage see Figure 8 Step 1 Use a Phillips screwdriver to loosen the screws on the drop in iris slot cover Do not remove screws Step 2 Slide the cover completely forward to expose the slot Step 3 Insert the iris with the flat side toward the shutters and make sure the iris handle extends from the slot English Step4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle Step 5 Secure the drop in iris slot cover by tightening the screws Adjusting the yoke position The Source Four jr jr Zoom provides multi positioning capabilities within its yoke for overall luminaire height and angle Setting the luminaire height within the yoke The luminaire is equipped with a two position yoke for modifying the overall height in which the luminaire is mounted see Figure 9 To change the height position perform the following steps General use position 4 Low clearance posit
13. to the extremely wide angle beam A variety of heat shield products is also available from many colour media manufacturers Follow the manufacturer s instructions for the use of these products Source Four jr jr Zoom CE User Manual C English Replacing the HPL lamp HPL lamp Lamp retention Lamp retaining cli brackets P gep Knurled bolt Figure 3 A lamp must be installed before you use the luminaire Note Verify that the HPL lamp you intend to install is suitable for your facility s voltage 115 120 230 and 240 volt HPL lamps are available See HPL lamp table page 4 Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure WARNING Let the lamp cool before replacing Step 1 Disconnect power to the Source Four jr jr Zoom CE before installing the lamp Step 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out Step 3 Holding by the base remove the HPL lamp from its box CAUTION Use caution when installing or replacing any lamp When installing replacing lamp be sure to point the lamp away from your face and away from others before inserting it firmly into the assembly This may prevent injuries if the lamp should break INCORRECT Pa CORRECT Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with isopropyl alcohol and a clean lint f
Download Pdf Manuals
Related Search