Home

Manual 2011-03

1. 2 The display briefly flashes and displays the serial number of the remote control 3 Press MODE button Display underscore 4 Press and hold 5 until P_ is displayed then enter the password 9999 quickly a confirmation signal will follow Display P_ 5 Enter the 6 digit serial number of the lift stated on the ID label on the side of the lift Press POWER button Display A1 0 Enter lowest lift number Display A1 1 Press POWER button Display A2 1 Enter highest lift number d DE ee Press POWER button Display 0 11 Short circuit the male connector by twisting together the 3 bared ends of the signal wires black red amp white and plug into the female connector 12 Press UP 13 Unplug the short circuited male connector 14 Readyto operate Enter lift number eg 1 Remark The lift must have a load of at least 40 of its litting capacity attached before lowering or raising Please be sure toregister the serial number of the device and the remote control D REELTECH 11 12 Wireless remote control functions Light on off Light down Set the lift code Change the series or unit mode Set the appliance Set the lowering distance REEL TEGH Gmo H Euro ps RCU This button is used to switch the light on When pressed again the light switches off Individual mode before switching on or off first enter the lift code number and press the LIGHT
2. REEL TECH GmbH Europe User Manual MOVE IT IT S POSSIBLE MODEL NO CSI 12 O LSI 10 CDI 15 PDI 35 CT HSI 18 O PDI 50 HDI 25 CT PFI 100 SDI 20 PFI 200 PSI 20 PFI 300 PSI 30 The technical data is the same for all models REEL TECH GmbH Europe Trillergasse 4 Top E721B 1210 Vienna Austria Tel 43 0 1 960 80 88 Fax DW 80 Email office reeltech eu Web www reeltech eu Thank you for purchasing this product Please read this manual carefully before installing or handling the product Please keep this manual as it contains your proof of purchase and guarantee Features Effective circular electrical contacts Large contact surface area ensures efficient power transfer Safe arch free system The power to the luminaire is automatically isolated before lowering and is restored when fully raised This safety feature prevents arching and prolongs the life of the contacts Protection category IP54 All the Reel Tech lift products are rated IP54 except the SDI LSI series 2 OREELTECH Maintenance free appliance Reel Tech lifts are maintenance free there are no user serviceable parts Reel Tech recommends a visual inspection of the suspension cables during operation to ensure that they are not damaged twisted or kinked The electrical installation must be carried out by qualified personnel and in accordance with local regulations The lift must be fixed with sui
3. to the luminaire 230 V 50 Hz 8 REELTECH Synchro Lifts batten or banner type 1 Maintain visual contact with the load during the operation The total load must be equal to the nominal load of one lifter For example The total load for the S HDI 25 is maximum 25 kg The total banner weight is also maximum 25kg 2 Make sure that the two serial numbers Main and Sub are identical MAIN SUB 4 THE DATE OF 200800 00 THE DATE OF MANUFACTORE MANUFAC TORE C Remote Lilirg Lighter Remote Lifting Lighter 3 If the lifters are not synchronized when lowering or raising press the STOP button The lifts will automatically reset can take 20 seconds and balance themselves when started again E Fr Gef SE Fri JES td FT A L d HEEN ME ng L REELT GmbH ECH Europ 9 Wireless Remote Control RCU Operating frequency 433 92 MHz REEL TECH CO LTD VW ITIL EST kr Functions On off power button for the remote control unit D Light on switch a Delete value 3 Light off switch 4 Lift up be Lift down Set number code for the unit for the light fixture F Group button for 4 group functions T The mode button is used together with the following buttons 5 FEN ET LA Vote group Aiiiiit On off button power for the remote control unit 10 REELTECH Programming the wireless remote control unit RCU 1 Press POWER button
4. Van Hennaertweg 7 NL 2952 CA Alblasserdam Tel 31 0 78 6920900 Fax 31 0 78 6920905 E Mail info industrielicht nl Poland MK Iluminacje Polska Sp z o o ul R Traugutta 25 PL 43 300 Bielsko Biala Polska Agata Kowalsczyk Manager Tel Fax 48 33 821 93 63 Email a kowalczyk mk iluminacje pl www mk iluminacje pl Germany ReelTech Vertriebs GmbH Rangenbergstr 33 D 60388 Frankfurt Main Wolfgang Vinson Managing Director Tel 49 0 6109 5016151 Fax 49 0 6109 5016150 Email office reeltech de Web www reeltech eu Hungary MK HUNGARIA Kft 9423 gfalva Baracsi t 77 G los Mih ly Manager Tel 00 36 99 524 007 Fax 00 36 99 524 248 Mob 00 36 20 46 811 43 m galos mk illumination hu Web www mk illumination com Denmark Norway Sweden Finland Baltic States Ellux Scandinavia AS Sjogt 15 PO BOX 1008 n 1510 Moss Norway Terje Sem Manager Te 004741362612 post ellux no www ellux no Czech Rep Slovakia Mk Illumination Production s r o Solivarska 1 A 080 01 Pre ov Slovakia Tel 421 51 7763125 Fax 421 51 7763128 Mob 421 917 505717 Email m balog mk illumination sk Web www mk illumination sk REELTECH 13 REEL TECH GMBH EUROPE Trillergasse 4 Top E 21B 1210 Vienna Austria Tel 43 0 1 960 80 88 Fax 43 0 960 80 88 80 Web www reeltech eu Email office reeltech eu HEAD OFFICE FACTORY 1402 26 Shindae Ri Haeryong Myun Sucheon Shi Jun
5. ON button to switch the light on There can be 1000 units between 0 and 999 Group mode select the group number from 1 to 4 then press LIGHT ON to switch the light on each group can have up to 1000 units This button is used to switch off the individual or group lighting modes These buttons are used to enter the group mode First press the MODE button until a beep sounds Then press 7 until you hear a beep when Group 1 appears on the display Repeat the procedure to exit group mode each group can have up to 1000 units This button is used to lift the light This function can be used in individual or in Group mode Tip Do not press this button twice during lowering or raising because it will delete the lowering height distance setting This button is used to lower the light This function can be used in individual or in Group mode Tip Do not press this button twice during lowering or raising because it will delete the lowering height distance setting Press the MODE 5 button to register the serial number set and then press POWER enter to register the appliance code in the next step set The A1 0 display ID the setting mode for the appliance code for registering The A2 0 is for registering the total number of units and is saved automatically Tip Up to 1 000 000 serial numbers can be registered individually or as a is changed to appliance code The user can chec
6. hold the stop button until you hear a confirmation signal E uran a 1 Isolate from the mains before 2 The installation must comply 3 Reel Tech lifts must only be connecting the lift to the power with local regulations and used for the purpose intended supply We recommend the use of guidelines The manufacturer s For example a multimeter instructions must be observed Lighting fixtures amp banners If in doubt check with your agent or the manufacturer Manual 4 The remote control unit must remain switched off before and after use to prevent accidental operation Both the remote control unit and the light fixture should not be exposed to excessive humidity vibration dust or corrosive gases i k corrosive gas e EN b 5 Do not modifying or tamper 6 During installation and 7 Power supply must with the lifts in any way It is operation ensure there is an be disconnected during dangerous and would cause a unobstructed area within a installation Only install malfunction The guarantee 3m radius below the lift with the power off would be null and void ceiling Y REELTECH 5 GmoH Europa 8 Do not operate the lift 9 Before operating ensure 10 Do not operate the lift if the without weight on the coupler the suspension cable is not cables are loose or caught up This should be at least 40 twisted or tangled of the lifts lifting capacity 11 Ensure that hands or 12 Operating te
7. k the unit with the serial number or the appliance code Tip we urgently recommend the user use the appliance code mode to control the units Warning the appliance code numbers are pre set by the manufacturer and we strongly recommend you do not change the serial number or appliance code These buttons are used to check the serial number of the unit First select the unit that the user would like to check and then enter the appliance code Then press MODE and 9 to check the serial number of the unit This button is used to set the lowering length of the cord First lower the light to a height where you can easily clean and maintain it from floor level To set the length press the STOP button a beep sounds A new beep sounds to confirm the setting Tip Press STOP for 5 seconds If in any doubt or for further advice contact your local distributor or agent United Kingdom REEL TECH UK Limited 22 Ibstock Close Billing Lane Northampton NN3 5DL David Willson Sales Director Lighting Lifts Tel 44 0 1604 643522 Mob 44 0 7540 449842 Email enquiries reeltechuk com Web www reeltech eu Switzerland Demelectric AG Steinhaldenstrasse 26 CH 8954 Geroldswil Edoardo De Monaco Manager Sales amp Marketing Tel 41 43 455 44 00 Fax 41 43 455 44 11 Direkt 41 43 455 44 35 Email e demonacoQdemelectric ch Web www demelectric ch Niederlande Industrielicht BV
8. mperature 13 Avoid excessive swinging objects do not get caught or downward impact of the between the upper and 15 to 60 C lowering section lower contacts as this can lead to injury and or malfunction 14 Only use the correct 15 Do not operate the appliance 16 Ensure that the appliance power source as indicated for longer than 10 minutes ata is earthed on the label Or the system time If the appliance overheats will fail wait until it has cooled down sufficiently before operating again 1 hour osovat 50Hz i CA REELTECH GmnH Europa Products Electrical cables for mains power supply blue brown Earth earth conductor green yellow Optional signal control wire for switched operation Black to red Raise black to white Lower e Main power cable feed N for lift and lighting circuit Housing Upper circular electrical contact Locking device operated by electric motor Lower circular electrical contac Stainless steel suspension cable So Lower standard cover ae Cable gland Suspension ring for the fixture Power cable for light fixture Y REELTECH 7 GmohH Europa Main power cable feed for lift and lighting circuit Optional signal control wire for switched operation For lowering and raising only black to red Raise black to white Lower N Supply from the mains KN K or the lighting circuit 230 V 50 Hz Electrical power cable
9. nam Korea Tel 82 61 723 1113 Fax 82 61 723 4440 Web www reeltech co kr Email postmaster reeltech co kr
10. table fixings not supplied to a mechanically safe and sound surface capable of withstanding the combined load of the luminaire and the lift If in doubt consult a professional structural engineer Automatic stop safety cut out The lowering distance can be pre set or adjusted manually during lowering using the remote control unit This enables the user to set a safe maintenance height and allows for flexible operation Tips maintenance and advice 1 The lift must not be used to carry people and must be installed at least 2 7m high 2 The operator must always work in accordance with the instruction manual 3 The person in charge must provide the necessary training of the service staff 4 The lift will not operate without mains power Manual operation is not possible 5 Excessive inching for example switching the motor on and off rapidly must be avoided 6 Do not exceed the lifting capacity of the lift 7 Do not attempt to lift fixed or jammed loads 8 Do not lower or lift loads diagonally 9 Replace the suspension cable after 100 operations except LSI series 10 Always maintain visual contact with the lift and the luminaire during operation Product overview Type Model Dimension WxDxH Lifting weight distance speed LSI 10 1 300x300x550 mm 3 10 kg Note Dimension without the eye bolt Reel Tech reserves the right to change or modify these specifications without notice The specified weigh
11. ts and dimensions are only approximate values and may vary REEL TECH 3 GmbH E Installation for authorised company only Attach lift to an eye not Using the supplied shackle secure luminaire to the supplied with the shackle lift and connect to the electrical supply 3 Vid 1 et Depending on local regulations a secondary safety fixing point may be required Connect the lift to the power RCU Power on Enter lift The lift must be fixed with suitable fixings supply As shown on page 7 number for example 1 and not supplied to a mechanically safe and press the DOWN button to sound surface capable of withstanding descend the combined load of the luminaire and E the lift If in doubt consult a professional structural engineer Control switch Only use a spring return retractive switch dead man s switch When operating with a switch the operator must always maintain visual contact with the lift and the luminaire durina operation N Electrical signal black to red RAISE black to white LOWER The remote control unit RCU must be switched off before and after operation in order to prevent accidental use When using the RCU eye contact with the appliance must be maintained The lift must have a load of at least 40 of its lifting capacity attached before lowering or raising Setting and saving the lowering length with the remote control In the desired position press and

Manual 2011-03

Contents

Download Pdf Manuals

Related Search

Related Contents