Digital Satellite Receiver SRT 6511
Contents
1. SAT OUT RS 232 Serial Port wn EN AUDIO Right and Left 5 VIDEO S PDIF an TV SCART DVD VCR SCART ON OFF Power Switch 0 Power Cord Go zl Figure 1 To put the receiver in and out of standby mode Used to display the main menu To show TV Radio channel list and to select a program highlight a line Channel up amp down Volume up amp down Signal Indicator Power indicator Shows channel number boot loader message and time in standby mode Figure 2 To connect the coaxial cable from your LNB on the satellite dish to this connector Gives you the possibility to connect an extra satellite receiver analogue or digital This serial port can be used to connect your PC to your receiver to download new software versions to your receiver Give you the possibility to connect the audio signal to an external amplifier or the audio input of your TV This connector has a constant video signal for additional VCR connections Use the coaxial output to connect your receiver to the input of your digital audio amplifier To connect your receiver to your TV using a SCART cable To connect your receiver to your DVD or Video recorder using a SCART cable Your receiver requires a current of 100 240 V AC Auto selectable 50 60 Hz 5 Make sure to check the power specification before connecting your receiver to the wall outlet 2 3 Remote Control Unit RCU 1 STANDBY ON 2 SAT 3 MUTE 4 NUMERIC2. THIS APPLIANCE TO RAIN OR MOISTURE AND ONLY USE THE RECOMMENDED ACCESSORIES m Read All Instructions Before you use the product read all operating instructions For more information on accessories such as the lithium ion battery refer to the manuals provided with those products m Save These Instructions Save all safety and operating instructions for future reference m Heed Warnings Read carefully and follow all warning labels on the product and those described in the instructions m Follow Instructions Follow all instructions provided with this product Cleaning Always unplug this product from the wall outlet before cleaning Use only a damp cloth for cleaning Never use any type of liquid or aerosol cleaner or any type of organic solvent to clean this product Attachments For your safety and to avoid damaging the product use only accessories recommended by STRONG m Water and Moisture Never use this product around water near a bathtub kitchen sink laundry tub wet basement swimming pool or in the rain Location To avoid damage to the product and prevent personal injury never place this product on an unstable stand tripod bracket table or cart Mount only on a stable tripod stand or bracket Follow the instructions that describe how to safely mount the product and use only the mounting devices recommended by the manufacturer m Power Sources Connect this product only to t
3. STRONG Digital Satellite Receiver SRT 6511 DIGITAL TV STRONG moar ILILILS digital Satair Hernies User Manual he nels TV Info lock www strong tv Fig 1 STRONG 0 1 MENU ok UU Digital Satellite Receiver j H b i E Supplied by STRONG amp Co Japan TELEVISION P Ka DIGITAL WV AUDIO AMPLIFIER TELEVISION O B mim DiSEqC SWITCH Motorized positioner PART 1 e English STRONG DIGITAL TV TABLE OF CONTENTS 1 0 INTRODUCTION 2 1 1 Safety Instructions 2 1 2 Storage 3 1 3 Equipment Set up 3 1 4 Features amp Accessories 3 2 0 YOUR RECEIVER 4 2 1 Front Panel 4 2 2 Rear Panel 4 2 3 Remote Control Unit RCU 4 3 0 CONNECTIONS 5 3 1 Connecting to TV 8 VCR 5 3 2 Connecting to Digital Audio Amplifier 5 3 3 Connecting to Satellite Dish 5 3 4 Connecting to computer by serial cable 5 4 0 STARTING UP FOR THE FIRST TIME 5 4 1 Language Selection 6 4 2 Audio Language Selection 6 4 3 Time Zone adjustment 6 4 4 Satellite configuration 6 5 0 MAIN MENU 6 5 1 Installation 6 5 2 Program Setting 8 5 3 User preference 8 5 4 System Setting 9 5 5 Utility 9 6 0 OTHER OPERATIONS 10 6 1 Electronic program guide EPG 10 6 2 Zap
4. buttons to select the correct setting press OK to confirm GOTO X settings Here you can setup your location in order to use GOTO X type of Positioner Motor Ifyou use a motorised dish DiSEqC 1 2 or DiSEqC 1 3 set DiSEqC1 2 or GOTO X if not then set to Disable by using the lt P buttons m DiSEqcC1 2 Almost same like GOTO X but without function of go to position X For settings please see below description m GOTOX Set motor to GOTO X and press OK to enter the menu to adjust the direction of the dish pointing to the selected satellite Position Auto Press lt P buttons the dish will be moved to West East continuously it will stop until it finds the best signal Move dish Press lt P buttons the dish will be moved to West East to search the best signal release the button will stop the moving Fine Tuning Set the fine tuning for optimised adjustment Move step Move to East or West stepwise Limit set Disable or enable West or East limit for mechanical limit D EES NOTE In order to avoid mechanical damage of your dish please make sure those mechanical limits in your motor are Je y set correctly and dish would not hit any objects on its movement Store position Press OK button to save the current position you searched Go to position Press OK button to move the dish to the stored position Go to Reference Press OK button to move the dish to 0 0 gt reference position Go to X X Press OK button to move the dish to
5. KEYS 0 9 5 RECALL 6 TV RADIO 7 MENU 8 EPG 9 FAV 10 EXIT 11 OK 12 lt gt 13 AV 14 VOL 15 PAGE AV 16 AUDIO 17 PAUSE 18 ZOOM 19 Figure 11 To switch the receiver ON or to Standby To show the scanned satellite list To turn the sound ON OFF To insert numbers To switch to previously watched channel To switch between TV and RADIO To activate main menu Electronic Program Guide To show the TV Radio program guide To get favorite channel list you set before To exit current menu or for cancellation To confirm the highlighted menu item To change volume in viewing mode To change program To change volume Page up down in menu To select or change the Audio language To freeze the picture Zoom function To show the current channel information www strong tv PART 1 e English STRONG DIGITAL TV 20 F1 Sleep Timer 21 F2 Subtitles 22 F3 No function 23 TXT Teletext 3 0 CONNECTIONS 3 1 Connecting to TV amp VCR Basic connection with a SCART cable Fig 3 1 Connect the satellite signal from the LNB to the SAT IN connector 2 Connect the TV SCART connector at the back of the receiver to the SCART IN connector on your TV set Basic connection with an RCA cable Fig 4 1 Connect the satellite signal from the LNB to the SAT IN connector 2 Connect the Video RCA connector at the back of the receiver to the Video IN RCA connector on your TV set Audio IN VIDEO IN 3
6. MM Use the numeric buttons to type in the end time Cycle You can set the cycle of the timer Once Daily Weekly MO FR Monday to Friday SA amp SU Saturday amp Sunday Once you finished the timer setup press the OK button to save the settings You can also edit and or delete current timer events Select the event using the A W buttons and press the GREEN Edit button or press the RED Delete button 5 5 3 Calendar The calendar will give you the convenience to check the date To change the year use the A Y buttons to change the months use the lt P buttons 5 5 4 Games The receiver has three games Tetris Snake Box Man In this menu you can select the game with the AW buttons and press OK to play the game www strong tv 2 STRONG PART 1 e English DIGITAL TV Tetris This is a very classic game you can play with the A W dk buttons lt gt Move block to left or right direction Y Drop block A Rotate block BLUE button Pause Snake lt gt Move snake icon to left or right direction AV Move snake icon to up or down direction If the snake has passed the brown food icon length will be increased if passed through the yellow icon length is decreased If it has passed through white icon current game is over BLUE button Pause Box Man You are the workman and you have to push the balls to their correct positions The box can only be pushed never pulled so you have to be careful not to push them into a corne
7. about the current program Satellite name Program name program number and time The following symbols are as well available below the current event headline For this signs the colour indicates availability gt Blue not available Yellow available SUB if subtitles are available for the current program TXT if Teletext available on the current program if the program is scrambled or Free To Air EPG if electronic program guide is available and the available selectable audio channels In the lower left corner the signal strength and quality are shown Furthermore you have the possibility to show the Now Next EPG headline using the RED Next button and if you press YELLOW O again you can see the detailed EPG info as well Use the AW and lt P buttons to scroll in the EPG Details On the Top bar are technical program details shown frequency symbol rate polarisation Video Audio PCR and Teletext PID and the number of Audio and Teletext channels 6 3 Audio Language selection In viewing mode press RED Audio button to show the list of audio languages Use the AW buttons to change the available audio language Use the lt P buttons to change the audio mode Stereo Left mono Right mono To cancel press RED or EXIT NOTE Audio track with AC3 sign can be listened only if receiver is connected via SPDI F to digital audio y amplifier and it is switched ON 10 www strong tv PART 1 English STRONG DIGITAL
8. button to add the selected channel to the chosen favorite group You can also rename the FAV group by pressing RED Rename Favourite button Use the lt gt and A Y buttons to choose characters from the shown keyboard press OK to insert Press GREEN Back button to delete character and use the RED OK button to confirm the new name 5 2 3 Sort Channels You can sort the channel order of the list by Alphabet FTA gt CAS Free To Air gt scrambled Satellite Transponder Favor gt No Favor Alphabet Channels will be sorted in alphabet order FTA gt CAS Free To Air channels will be placed at the beginning of the list Scrambled at the end Satellite Channels will be sorted in Satellite order Transponder Channels will be sorted in the order they were found beginning with lowest to highest frequency within a satellite Favor gt No Favor First favourite channels will be sorted followed by channels which are not Favourites 5 3 User preference This menu allows you to change several settings concerning OSD On Screen Display as Colour Transparency Search Speed OSD Time Out and Parental Control Colour With the lt P buttons you can choose between two OSD colours Transparency Use the lt P buttons to set the transparency as you prefer 1 stands for highest transparency 18 for opaque Search Speed With the lt P buttons you can set the speed for channel search between Normal and Super Fast OSD Time Out Use the l
9. exact position of the satellite FTA only Use the lt P buttons to select YES if you want to search only for Free To Air channels and NO if you want to search for scrambled channels as well Start Search Use the lt P buttons to select the scan mode for Transponder Satellite or Advanced Scan 5 1 2 Edit Satellite data Dependent on the focus you set with the lt P buttons you can edit a satellite or its transponder data Select a satellite or transponder with the A Y buttons and press OK to enter the menu then PIN code default 0000 is requested In case you have chosen satellite the following possibilities are available Rename Delete Move Add Rename Now you can use the lt P and AW buttons to choose characters from the shown keyboard press OK to insert Press GREEN Back button to delete character and use the RED OK button to confirm the new name Delete This will delete the selected satellite A message will appear press OK if you want to delete the satellite or EXIT to cancel Move Here you can move the position of the selected satellite in the satellite list Use the numeric buttons to enter new position Add Use the numeric buttons to enter orbital position of the new satellite and lt P to select between East or West In case you have chosen transponder these possibilities are available Delete Edit Add Delete This will delete the selected transponder Edit Use the numeric buttons to enter the new value for th
10. in mm 280 x 235 x 60 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004 108 EEC and 73 23EEC RoHS 2002 95EEC Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change All product names are trademarks or registered trademarks of their respective owners STRONG 2010 All rights reserved 03 2010 12 www strong tv
11. the authorized service center uses only parts with the same characteristics as the originals as recommended by the manufacturer Unauthorized substitution of parts could result in fire electrical shock or create other hazards m Safety Check Upon completion of servicing or repairs ask the service technician toperform safety checks to determine that the product is in good working order m Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus m Where the mains plug or all pole mains switch is used as the disconnect device the disconnect device shall remain readily operable www strong tv PART 1 e English STRONG DIGITAL TV 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 1 3 Equipment Set up We recommend you to consult a professional installer to set up your equipment Otherwise please follow the instructions below m Refer to the user manual of your TV and your antenna m Make sure that t
12. Connect the Audio Left and Right RCA connectors at the back of the receiver to the Audio Left and Right IN connectors on your TV set or audio amplifier Advanced connection of the receiver to the TV set and DVD Video recorder Fig 5 1 Connect the satellite signal from the LNB to the SAT IN connector 2 Connect the TV SCART connector at the back of the receiver to the SCART in connector on your TV set 3 Connect the VCR SCART connector at the back of the receiver to the SCART in connector on your VCR 3 2 Connecting to Digital Audio Amplifier Connect your Digital Audio Amplifier with the S PDIF connector on the back of the receiver Fig 6 3 3 Connecting to Satellite Dish Connecting a fixed satellite dish to your receiver Fig 7 First choose a satellite you want to receive your signals from and have your dealer aim your dish at the requested satellite Connect a coax cable to your LNB and the other end directly to the SAT IN connector of your receiver Connecting multiple fixed dishes to your receiver using a DiSEqC 1 0 switch Fig 8 If you want to watch programs from more than one satellite For example from ASTRA and from HOT BIRD it is advisable to use fixed dishes and a DiSEqC 1 0 switch Have your Dealer aim the dishes at the requested satellites and connect the LNB s with coax cables to the IN connectors of the DiSEqC 1 0 switch Connect the OUT connector of the DiSEqC 1 0 switch to the SAT IN connector at the back of your rece
13. If it is set to YES then receiver additionally search for channels from new transponders via NIT Network Information Table Use this option to get newly appeared channels from the satellite 5 1 6 mySat Search This function will help you to easily and quickly setup satellite installation Once receiver has finished you will see satellite s which is are found and can execute channel search for Scan ALL channels RED or to Scan Free channels GREEN 5 2 Program Setting 5 2 1 Edit Channels In this menu you can Rename YELLOW Move GREEN Delete RED and Lock BLUE channels Use the AW buttons to select a channel which you want to edit and then press the corresponding button Rename Here you can rename the channel Use the lt P and AW buttons to choose characters from the shown keyboard press OK to insert Press GREEN Back button to delete character and use the RED OK button to confirm the new name Move Here you can move the selected channel to desired position use the numeric buttons to enter Delete If you press the RED button the selected channel s is marked with X to delete Once you have pressed EXIT you will be asked if you want to delete press OK to confirm or EXIT to cancel deletion Lock By pressing the BLUE button you can lock or unlock a selected channel the D will be shown beside the selected channel 5 2 2 Edit Favourites In this menu you can choose between 7 FAV groups using the lt P buttons Press OK
14. STRA 19 2E or HOT BIRD 13E In this case you are guided to Antenna Setting s and have to setup your Satellite manually for details refer to chapter 5 1 1 Antenna Setting s Select mySAT if you have connected a single dish or multiple fixed dishes and want to install automatically Select RED Single Dish or YELLOW Multiple Dish Now the receiver starts process to detect the correct satellite s Once finished your receiver shows the found satellite s amp you can execute a channel search on it them with RED to Scan ALL channels or GREEN to Scan Free channels 4 4 2 DiSEqC 1 2 You are now guided directly to menu Antenna Setting s gt Motor setup which gives you the possibility to point the dish to correct position Use the A Y and lt P buttons to select and change the settings for details refer to chapter 5 1 1 Antenna Setting s under point GOTO X 4 4 3 GOTO X Settings If you have selected this configuration then you need to select your country from the list using the AW buttons If your country is not available you have to choose User define where you can insert the correct position for your longitude angle and direction latitude angle and direction and the rotating speed 5 0 MAIN MENU All the important settings and features of your receiver can be operated in Main Menu The Main Menu consists of following sub menus Installation Program setting User Preference System Setting and Utility Press MENU b
15. TV 6 4 Channel list and view mode In viewing mode press OK button and the channel list will be shown Press the AW buttons to select the channel and press the OK button to view selected channel To switch between TV and Radio channels press the TV Radio button You can sort channels by FTA gt CAS by pressing the RED button or A Z by pressing the YELLOW button You can select satellite by pressing the GREEN button 6 5 FAV list In viewing mode you can get the Favorite channel list by pressing the FAV button Press the RED button to change FAV group Ifyou did not set favorite channels before it will show All channels list 6 6 Teletext function In channel view mode press the TEXT button The OSD Teletext will be shown in case Teletext is available on the current program With the AY buttons you can scroll displayed page number You can insert page number directly with the numeric buttons 6 7 Subtitle function In channel view mode press the F2 button The list of selectable subtitle languages will appear if DVB subtitle available With the A Y buttons select the subtitle language and press the OK button In case DVB subtitle aren t available you can search at Teletext if therefor subtitles are available NOTE 6 8 Sleep Timer function Press the F1 button to activate the sleep timer Use the lt P buttons to switch between following modes OFF 15 Min 30 Min 45 Min 60 Min 90 Min 120 Min and Min gt where you can enter
16. e selected Frequency and Symbol rate and use the lt gt buttons to select the correct Polarisation and FEC Add Like described above but this will add a new transponder 5 1 3 Remove Satellite Here you can remove an installed satellite from the list Use the A Y buttons to select the satellite you want to remove press OK to enter the menu then PIN code default 0000 is requested After entering the PIN code the satellite is marked with X to delete You can select other satellites to remove or press EXIT You will be asked for confirmation to delete OK or cancel EXIT www strong tv 7 STRONG PART 1 e English DIGITAL TV 5 1 4 Satellite Search In Satellite Search menu you ll find satellite list and transponder list Select one or more satellite s you want to search and press OK to select Press RED if you want to Scan ALL channels or GREEN to Scan Free channels 5 1 5 Manual TP Search This menu allows you to search for specific transponders Use the AW and lt P buttons to select the satellite and transponder you want to search for Furthermore you can use Network search function to find new appeared transponders With PID search you can enter specific data of a channel After setup and selection pressing OK will start the defined scan v Nd NOTE If Network search function is set to NO then receiver will search for the channels that are available from id preset transponder table of selected satellite
17. es once daily weekly working days weekend for programming and separate sleep timer m Full multi lingual DVB subtitling and audio track support m Multi lingual support on screen menu OSD such as English German Czech Slovakian Hungarian Bulgarian Russian Turkish m Edit functions for TV or Radio programme name and satellite name m 3 Games Boxman Tetris Snake and Calendar m Software update via RS 232 port m Signal quality and strength bar for digital transponders m Automatic and manual channel scan options m Power on with last viewed channel m User friendly remote control with coloured function buttons infrared up to 7 metres m Supports DiSEqC 1 0 DiSEqC 1 2 and GOTO X m PAL NTSC compatible m Power switch Depending on local signal conditions Availability depending on broadcaster Accessories m User s Manual m 1 Remote control unit m 2 x Batteries AAA type www strong tv 2 STRONG PART 1 e English DIGITAL TV NOTE The batteries should not be recharged disassembled electrically short circuited or be mixed or used E with other types of batteries Ifrechargeable accumulators instead of batteries are going to be used we recommend using e g NiMH types with low self discharge to ensure long time operation of remote control 2 0 YOUR RECEIVER 2 1 Front Panel Power Menu OK CH AV VOL lt gt Lock LED Power LED Display 2 2 Rear Panel Am bah 1 SATIN
18. he SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow A WARNING Indicates warning information yu Tips Indicates any other additional important or helpful information A MENU Represents a button on the remote control or the receiver Bold Character Move to Represents a menu item within a window Italic Character 1 4 Features amp Accessories m For all digital Free To Air TV and Radio channels via satellite m Excellent Audio amp Video quality m Quick and easy installation amp user friendly menu m mySAT function identification and automatic installation of your significant satellites m Memory capacity for 4200 channels resp 4000 transponders or 100 satellites m Fast channel zapping sorting by alphabet free encrypted channels or satellite m Advanced Zoom functions for TV pictures m Digital sound through coaxial output S PDIF by connecting to digital amplifier m Parental lock function for menu and selectable per channel m 7 Favourite lists for TV and Radio channels m Very fast 800 pages teletext via receiver and teletext via TV remote control m Display showing channel number or time m Electronic TV Programme Guide EPG for on screen programme information of present following event information up to 7 days m 8 Timers with 5 mod
19. he power source described on the product label If you are not sure about the type of power supply in your home consult your local power company m Refer to instruction pages for information on using the product with a battery Grounding Polarization If this product is used with a specified AC adapter the adaptermay be equipped with a polarized alternating current line plug a plug with one blade wider than the other This safety feature allows the plug to fit into the power outlet only one way If you cannot insert the plug into the wall outlet pull it out reverse it and then reinsert it If the plug still fails to fit contact an electrician and have the receptacle replaced Protecting the Power Cord The power supply cord should be placed so it will not bewalked on Never put a heavy object on the power cord or wrap it around the leg of a table or chair Keep the area around the power cord connection points at the power outlet and at the product connection free of all AC adapter or accessory power cords DY AE GENERAL PRECAUTIONS SAFETY PRECAUTIONS m Lightning If a lightning storm occurs while using a specified AC adapter remove it from the wall outlet immediately To avoid damage from unexpected power surges always unplug the AC adapter from the power outlet and disconnect it from the receiver when the receiver is not in use m Overloading Never overload wall outlets extension cords power strips or ot
20. her power connection points with too many plugs m Foreign Objects Liquid Spillage To avoid personal injury caused by fire or electrical shock from contact with internal high voltage points never insert a metal object into the product Avoid using the product where there is a danger of spillage m Heat Never use or store this product near any heat source such as a radiator heat register stove or any type of equipment or appliance that generates heat including stereo amplifiers m Servicing Refer all servicing to qualified personnel Attempting to remove the covers or disassemble the product could expose you to dangerous high voltage points m Damage Requiring Service If you notice any of the conditions described below while using a specified AC adapter unplug it from the wall outlet and refer servicing to qualified service personnel 1 Liquid has been spilled onto the product or some other object has fallen into the product 2 The product has been exposed to water 3 The product does not operate normally despite following operating instructions Adjust only the controls described in the operating instructions as improper adjustment of other controls could damage the product and require extensive repair work by a qualified technician 4 The product has been dropped or damaged in any way 5 The product exhibits a distinct change in performance m Replacement Parts When replacement parts are required make sure that
21. iver Connecting a dish on a motorized positioner to your receiver Fig 9 Another possibility for watching programs from multiple satellites is by mounting a dish to a motorized DiSEqC 1 2 positioner Have your dealer mount the dish to the positioner set the correct angle of the elevation and let him set the center point for your positioner Connect the LNB with a coax cable to the SAT IN connector of the positioner and connect the OUT connector of the positioner to the SAT IN connector at the back of your receiver 3 4 Connecting to computer by serial cable Connect the RS 232 connector on the back of your receiver to the serial port of your computer using a serial crossed Sub D9 cable You ll find instructions how to download software and a loading tool on our website www strong tv support gt download Fig 10 4 0 STARTING UP FOR THE FIRST TIME Ensure your satellite receiver is connected correctly to your television and dish and that your satellite signal is of good quality Ifyou are not sure about this then ask your local STRONG dealer to check your installation or satellite signal Confirm that the power plug on the receiver is plugged into the wall outlet Turn on the receiver It is recommended that you perform the first time installation following the Installation Wizard step by step It will help you to easily achieve system configuration and channel installation If you are a professional installer then you can skip wizard by p
22. l a professional installer Check whether the batteries are inserted correctly or if they are exhausted and replace them www strong tv 11 STRONG PART 1 e English DIGITAL TV A 2 PIN CODE The default PIN code is 0000 A 3 SPECIFICATIONS Demodulator Modulation QPSK Input Symbol Rate 2 45 Ms s SCPC amp MCPC signals from C amp KU band satellites Video Decoder Profile level MPEG 2 Main profile Main level Data Rate Up to 60 Mbit s Video Resolution 720 x 576 720 x 480 Video Format NTSC PAL Aspect Ratio 4 3 16 9 Audio Decoder MPEG 1 MusiCam Layer I amp 11 AC3 Audio mode Mono Dual mono Stereo Sampling Rate 32 44 1 48 kHz Tuner Input Frequency Range 950 2150 MHz Input signal level 65 25 dBm LNB Power 13 5 18 5 V DC max 500 mA Overload protected LNB switch control 22 kHz DiSEqC Version 1 0 amp 1 2 compatible Connectors SAT IN SAT OUT 1 TV SCART RGB CVBS Audio with volume control 1 VCR SCART CVBS Audio with volume control 3 RCA Audio L amp R Video Coaxial Digital Audio S PDIF Separate power switch System amp Memory Main Processor CONEXANT CX24142 Flash Memory 2 MBytes SDRAM 16 MBytes General Data Supply Voltage 100 240 V AC 50 60 Hz Power Consumption typical 11 W max 20 W Stand by Mode lt 6 5 W Operating Temperature 0 40 C Storage Temperature 10 50 C Humidity 10 85 Size W x D x H
23. ping and information banners 10 6 3 Audio Language selection 10 6 4 Channel list and view mode 1 6 5 FAV list 11 6 6 Teletext function 11 6 7 Subtitle function 11 6 8 Sleep Timer function 11 6 9 Zoom function 11 A 1 TROUBLESHOOTING 11 A 2 PIN CODE 12 A 3 SPECIFICATIONS 12 LU FM 0180 500 75 43 Z 0 14 Min from German wired line 0820 400 150 E e 12 Min from Austrian wired line O HE 0826 029 928 L 0 14 Min from French wired line per June 2008 www strong tv 1 STRONG PART 1 e English DIGITAL TV 1 0 INTRODUCTION 1 1 Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE FOR SERVICING Explanation of WARNING symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage within the inside ofthe product that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance Read the following instructions carefully WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR ANNOYING INTERFRERENCE DO NOT EXPOSE
24. r where you can t get them out again You can only push one box at the same time You can move around by using the lt P A Y buttons Press RED to Replay this level or GREEN to go to Next level or YELLOW to play Previous level 6 0 OTHER OPERATIONS 6 1 Electronic program guide EPG The EPG shows the current and following program schedule dependant on the broadcast it can be shown for up to 7 days Press the EPG button on the RCU in viewing mode to enter the EPG With the AW buttons you can select the events from the current program and with the lt P buttons you can select the next previous days Press the YELLOW button to display the detailed information of the selected event Press the OK button to display channel list and use the AW buttons to select the channel and then press OK to display EPG of the selected channel You can program an Event Timer directly from the EPG menu if you select the event and then press the RED Timer button The parameters for the selected event are already filled out in the appearing Timer menu If necessary you can change the settings using the A Y buttons Once all settings as you request press the OK button to add the timer event A NOTE Not all broadcasters provide program information v 6 2 Zapping and information banners In viewing mode press the YELLOW O button to show Zapping banner together with technical program details on screen On the lower bar you can view the following information
25. ressing EXIT button and set up channels using the Installation menu for details refer to chapter 5 1 www strong tv 2 STRONG PART 1 e English DIGITAL TV 4 1 Language Selection Press AW buttons to choose your language press OK to confirm In case of German selected there is an extra option available of preset antenna configuration with ASTRA 19 2E LNB1 and HOT BIRD 13 0E LNB2 through DiSEqC switch In Czech the configuration ASTRA 19 2E LNB1 and ASTRA 23 5E LNB2 is available 4 2 Audio Language Selection Select your preferred Audio language using the A Y buttons and press OK to confirm If you have pressed OK by mistake or confirmed a wrong setting you can use the GREEN Back button to get one step back at every step of Setup Wizard 4 3 Time Zone adjustment Select your Time Zone according to the region you live using the AW buttons For Summertime use the lt P buttons to select the correct setting then press OK to confirm 4 4 Satellite configuration Select one of the available connection types Fixed dish DiSEqC1 2 or GOTO X Settings using the A Y buttons according to your used dish installation Depending on the selected Installation you will be guided to different Setup steps 4 4 1 Fixed dish Now you have the possibility to install your channels from the connected Antenna s For manually installation select Search Channel with the A W buttons in case you are connected to single dish and want to setup e g A
26. se the lt P buttons to set the type of SCART output signal System Info Press OK to show Info about Software version Loader Company and Software built date TIP Please submit this information to the service in order to get correct and fast after sales service 5 5 Utility This menu consists of following submenus Time Setting Event timer Calendar and Games 5 5 1 Time Setting The default time mode is set to Auto If broadcaster provides GMT you can set the time zone accordingly or set your time manually For the option AUTO you have to set the Time Zone and Summer time using the AW and lt P buttons to select and change settings If you set Time mode to Manual you need to set Current time and set Current Date using the AW buttons Use the numeric buttons to type in the current time in HH MM and date in DD MM YYYY format To delete current value use the 4 button 5 5 2 Event Timer Here you can set a timer to perform in following modes Once Daily Weekly MO FR and SA amp SU including timer based power on and power off Press the YELLOW Add button to add a new Timer With the A W buttons you can select the timer options and with the lt P buttons you can change the values of selected options Channel type Select between TV and Radio Channel Select channel from the channel list Date DD MM Use the numeric buttons to type in the start date Start time HH MM Use the numeric buttons to type in the start time End time HH
27. t P buttons to set the banner timeout 8 www strong tv PART 1 e English STRONG DIGITAL TV Parental Control Default this small submenu shows Input New PIN code and Confirm PIN code where you can enter new PIN code and confirm it if you want to The default PIN code is 0000 Use the lt gt buttons to set Option for Password Lock and Menu Lock If you want to lock channels the Password Lock must be switched to ON or if you want to lock the whole menu then Menu Lock must be switched to ON please confirm settings with OK 5 4 System Setting This menu allows you to change several settings concerning Menu Language Audio Language TV Type TV Screen Mode Factory Default Video Output or view the System Info Menu Audio Language Use the lt P buttons to set your preferred Menu and Audio language TV Type With the lt P buttons set the type your TV set is using If you don t know which standard your TV has please select PAL NTSC TV Screen Mode Use the lt P buttons to set 4 3 Letter Box Pan amp Scan 16 9 Wide TV or Auto according the used TV set Factory default Please select with the lt P buttons which type of factory default you want to execute All for all data and settings Channel List if you only want to set channel list to default Only Radio List if you only want to set radio channel list to default and Only Scrambled Channel if you only want to set scrambled channel list to default Video Output U
28. uttons in no menu state to enter MAIN MENU 5 1 Installation The installation menu contains following sub menus Antenna Setting s Edit Satellite data Remove Satellite Satellites search Manual TP Search and mySAT Search 5 1 1 Antenna setting s Press OK button to enter Antenna Setting s menu Satellite Here is the first pre stored satellite shown Use the gt button and AW buttons to select another satellite from the list press OK to confirm Transponder If you change the satellite the transponder table will be changed automatically Use the B button and AY buttons to select a transponder from the corresponding satellite press OK to confirm LNB frequency Default configuration is set to Universal if another LNB is used set the frequency accordingly to the used LNB or define yourself gt User define 22 kHz This configuration is preset to Auto because this is the most usual setting for Universal LNB s in case your LNB requires another setting you can switch it permanently ON or OFF by using the lt P buttons 6 www strong tv PART 1 e English STRONG DIGITAL TV DiSEqC If your antenna is connected through a DiSEqC switch and you have already executed the First Installation with mySAT search then this setup is already according your installation You only need to specify the DiSEqC input in case it has been wrong configured or the installation setup has changed Use the lt gt
29. your preferred time The availability of DVB subtitle depends on the broadcaster 6 9 Zoom function Press GREEN Zoom button to get pointer then use the AW and lt P buttons to select position you want to zoom in and press OK to activate the function A 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact the dealer Do NOT open the receiver cover It may cause a dangerous situation and the warranty will get void Wario do The display on front panel does The power cord is not plugged in Check that the power cord is plugged in to not light up the wall outlet No picture or sound Wrong connection of the Audio Connect the Audio Video output of the Video output of the receiver to TV Audio muting TV power off No picture The receiver can t receive the signal Incorrect values of some tuner parameters Wrong direction of the dish The batteries of the remote control are not inserted or exhausted The remote control does not work receiver to TV correctly Press the Mute button Turn TV on Check the antenna cable replace the cable or connect the cable to the receiver tightly Set the values of tuner parameters correctly in installation menu Check the signal strength with a professional satellite finder and adjust your dish correctly or cal
Download Pdf Manuals
Related Search