User Manual
Contents
1. HD TVI Bullet Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual may contain several technical incorrect places or printing errors andthe content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described inthe manual Please refer to the product specification for camera parameters and functions Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits fora digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interfere2. igurable NEG IMAGE Set the NEG IMAGE as ON or OFF SPECIAL aaa 1 CAMTITLE ON4 2 D DFFECT 1 SELECT AREA 1 3 MOTION OFF 2 DISPLAY oON 4 PRIVACY OFF 3 SENSITIVITY 30 5 LANGUAGE ENG 4 MOTION VIEW ON G DEFECT a 5 DEFAULT 7 VERSION 130722 6 RETURN RET 8 RETURN RET Figure 3 7 Special Figure 3 8 Motion Detection Motion Select a MOTION area Set the DISPLAY status as ON or OFF Press the up down left right button to define the position and size of the area Set the SENSITIVITY from 0 to 60 Set the MOTION VIEW status as ON or OFF Privacy Select a PRIVACY area Set the DISPLAY status as INV MOSAIC COLOR or OFF Press the up down left right button to define the position and size of the area Defect LIVE DPC STATIC DPC and Black DPC are adjustable in this section Version You can check the software version of the device PRIVACY ADJUST 1 SELECT AREA 1 2 DISPLAY MOSAIC 1 SHARPNESS 15 3 COLOR 10 2 MONITOR LCD 4 TRANS 1 3 LSC OFF 5 DEFAULT a 4 VIDEO OUT PAL 6 RETURN RET 5 RETURN RET Figure 3 9 Privacy Mask Figure 3 10 Adjust 3 3 9 ADJUST Sharpness Adjust the sharpness from 0 to 15 Monitor Monitor CRT and Monitor LCD are selectable LSC Set the LSC status as ON or OFF 3 3 10 RESET Reset all the settings to the default 3 3 11 EXIT Press OK to exit the menu
3. ll the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes 2 i Ceiling Mounting 2 2 No 1 Screw Hole No 2 Screw Hole for Bracket for Mounting Base 4 Figure 2 4 Drill Template 3 Route the cables to the cable hole and connect the corresponding power cable and video cable 4 Fix the camera to the ceiling with the supplied screws Adjusting Screw Figure 2 5 Fix the Camera to the Wall 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the pan position 0 360 2 Tighten No 3 adjusting screw 3 Loosen No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the rotation position 0 360 6 Tighten No 1 adjusting screw Figure 2 6 3 axis Adjustment 3 Menu Operation Menu SCENE LENS EXPOSURE BACKLIGHT WB DAY amp NIGHT nr seciat apwusr RESET iNnnoor MANUAL ShuTTeR 4 BLC gt C ATW coor 20 NR as Guareness exit OUTDOOR AGC D Hserc awe ser C B W E NR D EFFECT monrror INDOOR1 SENS UP INDOOR EXT MOTION LSC 4 LOW LIGHT BRIGHTNESS OUTDOOR PRIVACY D WDR MANUAL DEFECT Peros VERSION Figure 3 1 Main Menu Note A coaxial camera controller purchase sepa
4. nce received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the F supplied accessories too are marked C 3 with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European WSU ion For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduction 1 1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise etc which makes it suitable for sur
5. rately is required to select the menu and adjust the camera parameters Cameras with a 720p resolution of these three types do not support menu operation 3 1 VIDEO OUT PAL or NTSC is selectable 3 2 LANGUAGE English Japanese CHN1 CHN2 Korean German French Italian Spanish Polish etc are selectable 3 3SETUP 3 3 1 SCENE You can select indoor outdoor indoor 1 and low light as the working environments 3 3 2 LENS The camera is equipped with a fixed lens 3 3 3 EXPOSURE SHUTTER AUTO 1 25 1 50 FLK 1 200 1 400 1 1k 1 2k 1 5k 1 10k 1 50k x2 x4 x6 x8 x10 and x15 are selectable AGC You can set the AGC value from Oto 15 SENS UP You can set the SENS UP to OFF or AUTO BRIGHTNESS You can set the brightness value from 1to 100 D WDR You can set the D WDR to ON to improve the image quality or OFF to disable the function DEFOG You can set the defog function as ON to enable the function Position size and the defog gradation are configurable EXPOSURE mae 1 SHUTTER AUTO 1 SELECT AREA 2 AGC OFF 2 DISPLAY ON 3 SENS UP z 3 LEVEL j 4 BRIGHTNESS 40 4 MODE ALL DAY 5 DEFOG OFF 5 BLACK MASK ON 6 BACKLIGHT OFF 6 DEFAULT a 7 RETURN RET ee aa Figure 3 2 Exposure Figure 3 3 HSBLC 3 3 4 Backlight Backlight Compensation BLC GAIN Set the gain of BLC as High Middle or Low AREA Press the up down left right button to define the BLC po
6. se make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wallis the cement wall you need to insert expansion screws before you install the camera If the wallis the wooden wall you can use self tapping screw to secure the camera elf the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Ceiling Mounting for Type Camera Steps 1 Drill the screw holes and the cable hole in the ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes Drill Template All Screw Holes for p mounting base 5 Figure 2 1 Drill Template 3 Route the cables to the cable hole and connect the corresponding power cable and video cable 4 Fix the camera to the ceiling with the supplied screws y Figure 2 2 Fix the Camera to the Ceiling 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the panning position 0 360 2 Tighten No 3 adjusting screw 3 Loosen the No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the azimuth angle of the image 0 360 6 Tighten No 1 adjusting screw Figure 2 3 3 axis Adjustment 2 2 Wall Mounting for Type II III Camera Steps 1 Dri
7. sition and size Select RET or AGAIN to go back the BLC menu or re define the BLC area Default Restore the BLC settings to the default HSBLC Select an HSBLC area Set the DISPLAY status as ON Press the up down left right button to define the area position and size Set the HSBLC LEVEL from O to 100 Select ALL DAY or Night for the HSBLC mode Set the BLACK MASK status as ON or OFF 3 3 5 White Balance WB INDOOR OUTDOOR MANUAL ATW Auto tracking White Balance AWCSET are selectable 3 3 6 Day amp Night Color B W and EXT are selectable for DAY and NIGHT switches 3 3 7 NR 2D NR You can set 2D NR status as ON or OFF 3D NR Set the Smart NR status as ON and adjust the 3D smart NR sensitivity ranges from 0 to 100 Set the 3D NR LEVEL ranges from 0 to 100 Set the START AGC level as the threshold to enable AGC and set the END AGC level as the threshold to disable AGC re 2D amp 3D NR 1 SMART NR ON 2 LEVEL 80 1 2DNR OFF 3 START AGC 10 2 3DNR ON 4 END AGC 10 3 RETURN RET 5 RETURN RET Figure 3 5 NR Figure 3 6 3D NR 3 3 8 SPECIAL Camera Title Edit the camera title on this section D effect FREEZE Set the freeze function as ON or OFF MIRROR OFF MIRROR V FLIP and ROTATE are selectable for mirror D ZOOM Define the zoom area by configuring the position from PAN amp TILT SMART D ZOOM The D Zoom area sensitivity and time are conf
8. veillance system and image processing system High performance CMOS sensor and high resolution bring high quality image Low illumination OSD menu parameters are configurable Support auto white balance auto gain control electronic shutter control SMART IR mode Unit transmission control Advanced 3 axis design meets different installation requirements 1 2 Overview 1 2 1 Overview of Type Camera Power Cable Switch Cable HD Vi Sunshielid ee Lens 1 2 2 Overview of Type Camera Adjustable Screw Sun Shield Power Cable Switch Cable 1 2 3 Overview of Type Camera Power Cable CVBS Cable E Allthe diagrams only apply to cameras with a 1080p resolution The cameras with a 720p resolution of these three types do not have CVBS cables and switch cables The switch cables are designed for toggling status of the WDR functions for 1080p cameras The WDR function is disabled by default and you can short the white and black line ends of the switch cable to enable the function 2 Installation Before you start Please make sure that the device in the package is in good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment eCheck whether the power supply is matched with your power output to avoid damage Plea
Download Pdf Manuals
Related Search