Home

USER MANUAL - Internet In Motion

image

Contents

1. Details Back Figure 15 Activation Status Activated or Not Activated Network Stability Indicates OK For Activation if during the previous two minute sample period the RSSI is less that smaller negative number 99dBm the SID has not changed and the unit has access to 1xRTT connectivity IOTA activations do not currently for when the connection is EV DO only SPC Unlock A code supplied by the network when your account is created MDN Mobile Directory Number the phone number assigned to the account MSID Mobile Station Identification a second phone number assigned to the account Detailed information on IOTA or OTAS activations are covered in the TechNote appropriate for your network The SPC MDN and MSID information is provided by your network operator when an account is assigned Once the network provided information is entered the Activate button will cause the Status and Details buttons can be used to monitor the activations progress 20 Part Number IIM2200A Release 1 00 neon Ageng yaa sommes Activation Detail Log Wed Apr 19 07 19 06 2006 START QIAS In tiat os PASS SEL unlock NEM download MOM download PEL download NV RAM write OTAS Successful Figure 16 21 Part Number IIM2200A Release 1 00 Start Manual Session Manual activations are performed using specific AT commands to program the CellRouter s radio module The Manual Session selection is a general purpose AT c
2. ESN De 09602660994 Hex 60289482 yston 4145 Phona Num MON 8056356504 Notwork Stam In Service Signal Lowel RSS B dEm 1xRTT and EvDO Curront IP Addross 68 27 90 36 PCS tatu Connected Roam Status Mot Roaming lemp Alor tomp OR Home Hetresh Detars Figure 19 Wireless Status Field Definitions Summary Display ESN An identifier assigned to the CDMA radio for this CellRouter The value is given in decimal Dec and Hexidecimal Hex System ID SID Numeric Identifiers assigned to local market areas within a wireless network Your wireless network operator may request this information if you are having trouble connecting to the network Phone Number MDN The circuit side phone number of the CDMA radio in your SkyRouter MDN stands for Mobile Directory Number Network Status Either In Service or Out of Service Indicates the state of the network as seen through your particular CellRouter Signal Level RSSI A measure of the strength of the wireless signal that your CellRouter is currently seeing A larger negative number indicates a marginal network connection Typically this number will be in the range of 75 95dBm although there are many locations where the value will be outside of the typical range 24 Part Number IIM2200A Release 1 00 Service Type The type of bearer channel this CellRouter is operating on Options are None 1xRTT 1xRTT and EVDO or EVDO Current IP Address The In
3. 1 None DDNS will not be used 2 EW SMS Use IIM Enhanced Wireless DDNS with SMS updates 3 EW UDP Use IIM Enhanced Wireless DDNS with UDP updates over the EV DO 1XRTT Air Interface 4 Standard UDP Use a standard BIND MS2000 or MS2003 DDNS server Device Name Establishes the name by which this particular CellRouter will be known at the Name Server This entry must be a fully qualified device name and domain and is limited to 40 characters in total It is limited to one level of name space definition meaning that all characters to the right of the first dot will be assumed to be a component of the resolving server An example would be IIMOl1 thingme net where ITMO1 is the name of an individual CellRouter and thingme net is the name of the resolving server Primary and Secondary Name Server Enter the IP address of the designated Name Server Name resolution is not performed on this entry meaning that a numeric IP address of the resolving server is required Provide Network Name Server Facilities Selecting Yes causes this CellRouter to provide Name Server services to client CellRouters configured to use it If this option is selected additional set up in the Name Services screen will be required 10 Part Number IIM2200A Release 1 00 4 2 2 Configuring The Ethernet Interace The Ethernet configuration determines how devices connected to the LAN side of CellRouter will be addressed and what the actual address of
4. Route TCP IP traffic UDP Route UDP IP traffic Enable Activate this routing setting Advertise This Service Display this named service for WAN users With Title The name assigned to this service Series 2200 CelfRouter Borping wa eme is Figure 11 17 Part Number IIM2200A Release 1 00 4 3 3 Admin Screen Services This service allows the user to control overall local and remote administrative access 3 inttp 192 1608 1 Miadmim binicte adrmin cgi Microsoft Internet Explorer e ES wew Favo fo Heb Q ke ix PA Search Lp wan e vem gt gt rat a As w Ga ho O bts 92 168 L 1D fodewn dan lp _adean cgi mnnn amin Screen Control Aron wa semn isd Porn Number For Admin Screen Access B0 Allow Network Access to Admin Screens Yes ONo Figure 12 Port Number For Admin Screen Access Causes the WAN side web server to listen on a port other than the default of Port 80 Allow Network Access To Admin Screens If set to Yes administrative users will be able to connect to CellRouter s Admin interface over the EV DO 1XRTT network connection If this selection is set to No only local administration is possible 18 Part Number IIM2200A Release 1 00 4 3 4 Wireless Activation Services Note Before using the Wireless Activation Services Interface for any purpose you must first turn off the CellRouter s WAN interface This is accomplished by setting the Wireless
5. deals with physical connectivity managing the connection and subtended devices Services are applications that are within the router core to modify the behavior of a specific interface or to change system wide parameters within the router core Status screens are provided for the CDMA ED DO 1XRTT and Ethernet interfaces Important Note The Restart button must be used to apply any changes made on specific Interface or Service screens 4 2 Interfaces 4 2 1 Configuring The Wireless Interface The configuration screen for the wireless interface is shown below The actual wireless interface is provisioned and configured by the wireless Network Operator CellRouter s Wireless Interface Configuration screen is used to establish inactivity timeouts and Name Server selections Part Number IIM2200A Release 1 00 rem apy Wireless Interface Configuration Netvrort Select O Amo v User Mame Wire tese C onne ctios Enables Passrvord Enable LCP echo pockets Use network provided dynamic IP address O Ube the fo lorena static IP addre x Chena For Dynamic P Address Resolution Select DOHS Type wore EW sms EYU DP O susrdard VUP Device Mame chon hinge roi Primary Name Server 63 1590 14 Secondary Wame Server 2161142839 Update Home Figure 6 Network Select Note This setting should only be changed after consulting with IIM Support This pull down menu allows the user to c
6. provides application and network designers with a bridge between the world of IT infrastructure and the evolving wireless data networks With CellRouter the wireless transport is fully integrated into the products routing fabric meaning that you can approach the setup and operation of this product much as with any other IP addressable device Wireless considerations are reduced to the absolute minimum necessary to register and make connections on a network 1 1 Theory Of Operation The Series 2200A CellRouter is a complete IP router that routes traffic over LAN Ethernet 10 100baseT connections The wireless features of CellRouter simply extend the IP routing capabilities to include routing and network address translation NAT over CDMA EV DO wireless networks A fallback 1xRTT transport is also provided As with most routers IM s Series 2200A CellRouter can be viewed as having a Local Area Network LAN side and a Wide Area Network WAN side Traffic originating at SkyRouter s Ethernet ports is considered LAN traffic The Wide Area Network connection is over the wireless network s IXR TT transport 1 2 Features This manual covers CellRouter 22004 Release 1 00 and contains the following feature and functions 1 Ethernet a Static Addressing b Dynamic DHCP Server c DHCP Client d Configurable DNS address e Configurable Gateway Sub net mask and Broadcast address f Port Forwarding g Service management 2 CDMA Interface a Ena
7. the Domain Name Server that your network uses This should not be confused with the Name Server entries on the Wireless Interface screen The DNS referenced by these addresses will resolve outbound queries IP Address The IP address assigned to the LAN segment of this CellRouter NetMask This parameter is also known as Subnet Mask Network Mask determines which portion of an IP address is the network portion and which portion belongs to the host As an example a setting of 255 255 255 0 would indicate that the first three groups of this address 255 255 255 identify the network and that the last group 000 254 identify a particular host Default Gateway The Default Gateway is the address of a device that CellRouter will use to reach remote networks or servers In many cases this will be a firewall address In a normal situation where the 2200 is acting as a fringe router and is expected to pass incoming Ethernet traffic through to the CDMA network this field should be left blank If the 2200 is acting as a RAS where traffic is coming in from the CDMA network so that it can be routed through to some sort of host server this field must set to an address on the 2200 s LAN segment Broadcast Address If applications on the 2200 need to do a broadcast operation this is the address that will be used on the Ethernet segment to fulfill the broadcast request 12 Part Number IIM2200A Release 1 00 4 2 3 Configuring The Relay In
8. there is a mandatory waiting period before the endpoint is allowed to reinitiate the request for a Static address registration During this period of time the network will dynamically assign addresses to the end point A DDNS service will make the end point network addressable by name during this period of time Secondly a name service allows your end point to be known by a name that is independent of network addressing Addressing a unit by name may be easier for end users to remember and will over a long period of time reduce maintenance problems 4 1 Getting Started Once the PC has been set up properly and physically connected to the CellRouter you are ready to begin configuring the Series 2200 CellRouter for your application To access the Administration menu use a conventional web browser pointed at http 192 168 1 10 A login screen appears as shown below The default User ID is c tek without the quotes and the default Password is also ctek Be sure to change the user ID and password and record your new selections Z Series 2200 CellRouter User Name Password Figure 4 When you have completed the login process you will be presented with the top level administration menu Part Number IIM2200A Release 1 00 Series 2200 CellRouter em os om lt lt INTERFACES SERVICES STATUS IIM Website Figure 5 Note that the administration menu is divided into three sections The Interfaces section
9. this CellRouter will be on the LAN 2 158 1 10 2dmin biricig eshO cgi Microsott internet Explorer Fu Get Vas Fares Josa Hep Qm MB J uwa Perens Gas O Ss Q VaR ls PESO ISS 188 1 LO Remin dees _ e289 E gt ix Google v dose BSS E EP priodas O vivos 4 ma Boryny a com v Ethernet Configuration Madia Type amo v DHCP Configuration Disabled Enable Server Enable Client ONS Address Source Acquire From Wireless Network O User Defined Primary ONS Address 6617437 Secondary UNS Address 661467 When DMC P Chani in enabled hova pras wl be lagara IP Address 192 188 1 10 Met Mask 255 255 255 0 Default Gateway Broadcast Address 192 1642355 285 Unda Hama Figure 7 Media Type Determines the type of Ethernet connection Auto allows CellRouter to determine what the connection is This setting is appropriate for most cases Other settings are to select either 10Mb 10baseT 100Mb 100baseT Full Duplex FD or Half Duplex HD Again in almost all cases Auto will correctly determine the proper setting DHCP Configuration These settings determine the network topology of the LAN side of CellRouter s network Disabled You must manually configure the IP address and other addressing parameters described in the next section It is recommended that the CellRouter be assigned a private static address of 192 168 1 10 Enable Server This CellRouter must be assigned a private s
10. 45 Ethernet 10 100baseT Full or Half Duplex auto polarity sensing Relay Input Interface Designed to detect closure or opening of relay contacts Physical 2 Pin Terminal Block See Appendix A for details Relay Output Interface Physical 2 Pin Terminal Block See Appendix A for details Wireless Interface CDMA EV DO with IXR TT fall back Physical SMA Antenna removable CDMA Approvals Compliant with IS 95 CDMA 2000 specifications FCC Part 22 24 and 15 Power Requirements Standard 9 18VDC JISVAC gt 12VDC Wall Transformer included Power Consumption 12VDC nominal CDMA Radio Off 180ma CDMA Radio On Data Channel Inactive 230ma CDMA Radio On 1 Ethernet Port Connected 384ma CDMA Radio On 4 Ethernet Ports Connected 445ma Environmental Operating temperature range 20C to 70C Humidity 90 non condensing Physical Dimensions 5 275 L x 5 225 W x 2 08 H Weight 1207 Mounting Self standing or wall mount 28 Part Number IIM2200A Release 1 00 6 Certifications FCC Part 15 This equipment has been tested and complies with the limits for a Class A computing device according to U S Code of Federal Regulations Title 47 FCC Rules and Regulations Part 15 Operation is subject to the following two conditions 1 This device may cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Te
11. Connection pull down on the Wireless Interface screen to disabled clicking update and then doing a restart of the unit The Wireless Activation Services interface serves two purposes First it provides a mechanism to activate the CellRouter on the wireless networks utilizing a form of Over The Air OTA activation Secondly it may be used as a general interface to enter specific commands known as AT commands to the CellRouter s radio module Internet in Motion gt Keeping yew comnevied Wireless Activation Services Stan OTA Session Sisi Manual Session Figure 13 Over The Air Network Activation If the wireless module in your CellRouter is capable of performing an OTA activation you will be presented with the option to select the appropriate activation method Currently this capability is limited to the IOTA method for Sprint Nextel or the OTAS method for Verizon Wireless In the Figure 13 example the IOTA choice is shown whereas Figure 14 shows the OTAS choice Selecting Start IOTA Session displays the user interface in Fig 15 Internet in Motion gt Keeping yew comnewied Wireless Activation Services Star OTA Session Sisi Manual Session Home Figure 14 19 Part Number IIM2200A Release 1 00 Internet da Motion gt Keping comet JOTA Activation Process Activation Status Not Activated Network Stability OK For Activation SPC Unlock MDN 3056356504 MSID 8056366504
12. Discrete Output See Appendix A Pin 5 Ground Pin 6 12VDC Figure 2 3 Start Up Warning You must connect antennas to the SMA style antenna connectors on the CellRouter before turning it on Failure to do this could result in erratic start up behavior and could possibly damage the unit Note The 2200 CellRouter ships from the factory with its DHCP server enabled The Default Gateway address for the unit is 192 168 1 10 The address of the web based administration is also 192 168 1 10 After you have activated your unit on the wireless network it WILL NOT have a DNS address meaning that public Internet web access will not work To load DNS values go to the Ethernet Interface screen select Acquire From Wireless Network and press the update button At this point the Primary and Secondary DNS addresses in the Ethernet Interface screen will be populated with the DNS addresses provided by your wireless network As a last step restart both the CellRouter and the connected PC Part Number IIM2200A Release 1 00 3 1 Power Before starting connect the supplied 12VDC power adapter to the power connector described in Section 3 The adapter supplied with your CellRouter is suitable for use with 120VAC 60 hertz wall power If you need a different power solution contac t ITM 3 2 Connecting The Antenna The antennas supplied with each CellRouter should be attached to the SMA style antenna connectors described in section 3 The ante
13. IIM2200A Release 1 00 Wireless Status Details Screen momen gt Keeping vou comnecied Wireless Interface Details Radio Configuration Radio Type Sprint PRL Version 20212 Firmware Rev p1708100 Hordware Rev 3 ESN Dec 09602660994 ESH Hex 60289482 MSID 6056366504 0056366504 Current Sia ts System ID 4145 Signal Level RS SI S7dBm Netujork Status In Service Roam Status Not Roaming Service Type 1xRTT and EvDO CumentiP Address 68 27 90 36 Band PCS Call Status Dormant Current Temp 35 C Temp Alert Temp OK Activation Status Not Activated Network Stability OK For Activation TxRTT States B dim EvDO Status RS SI 97dBm Channel 5 Fere Wireless Status Field Definitions Detailed Display The Wireless Status Details screen is subdivided into four panels Radio Configuration Current Status EV DO Status and 1xRTT status All values found on the Summary screen are repeated on the Details screen Radio Configuration Panel Radio Type Indicates the type of programming originally loaded into the radio module Distinct radio types do not exist for all networks meaning that a unit operating on a given network may have been repurposed from one of the existing radio types 26 Part Number IIM2200A Release 1 00 PRL Version The Preferred Roaming List PRL currently loaded in the radio module Firmware Rev The revision level of the firmware currently loaded in the radio module H
14. Internet In Motion gt Keeping you connected USER MANUAL Series 2200A Part Number IIM 2200A Firmware Release 1 00 Part Number IIM 2200A Release 1 00 Table of Contents TABLE OF CONTENTS PREFACE 1 INTRODUCTION 1 1 Theory Of Operation 1 2 Features 2 CONNECTORS LIGHTS SWITCHES AND JUMPERS 2 1 Switches 2 2 Lights 2 3 Connectors 3 START UP 3 1 Power 3 2 Connecting The Antenna 3 3 Connecting to the Ethernet Port Administrative Connection 4 ADMINISTRATION CONFIGURATION AND STATUS 4 1 Getting Started 4 2 Interfaces 4 2 1 Configuring The Wireless Interface 4 2 2 Configuring The Ethernet Interace 4 2 3 Configuring The Relay Input Interface 4 2 4 Configuring The Relay Output Driver Interface 4 3 Services 4 3 1 Password Administration 4 3 2 Routing and Forwarding Services 4 3 3 Admin Screen Services 4 3 4 Wireless Activation Serv ices 4 3 5 Applications 4 4 Status 4 4 1 Wireless Status 4 4 2 Ethernet Status 5 SPECIFICATIONS 6 CERTIFICATIONS 7 APPENDIX A Part Number IIM2200A Release 1 00 28 29 30 Part NumberIIM2200A Release 1 00 Preface Welcome to the IIM Series 2200a CellRouter User s Guide The User s Guide will explain the basic operation of a Cell Router and take you through the necessary settings to get your wireless application online Additional information and applicable technical notices can be found at www internetinmotion net 1 Introduction CellRouter
15. Lights The Series 2200A CellRouter has indicators as shown in Figure 1 LAN1 LAN4 The LAN indicators indicate that an Ethernet port is connected to an active Ethernet device The network status indicators LINK and SVC are interpreted as follows SVC Multi color yellow green Indicates a Power b RSSI Display Definition Off No Power Yellow Blinking Power On No Signal RSSI Yellow Solid Power On RSSI lt 88 Green Solid Power On RSSI gt 88 Part Number IIM2200A Release 1 00 Link Multi color red green Indicates a Status of IP connection b Type of transport EV DO or 1xRTT Display Definition Off No Connection IP address Green Connection established on 1xRTT Red Connection established on EV DO Note Early production units serial number less than 0603051 010 have a different LED display No service Green off Yellow on In service signal less than 88 no connection Green LED off but does one short blink on every 4 5 seconds Yellow on In service EVDO or EVDO amp 1xRTT signal less than 88 no connection Green LED off but does one short blink on every 4 5 seconds Yellow LED off but does one short blink on every 4 5 seconds In service signal greater than or equal to 88 no connection Green LED off but does two short blinks on every 4 5 seconds Yellow on In service EVDO or EVDO amp 1xRTT signal greater than or equal to 88 no connection Green LED off but d
16. ardware Rev The revision level of the radio module MSID Mobile Station Identification MSID a second phone number assigned to the module Current Status Panel Current Temp The temperature currently being sensed by the radio module Values are in Centigrade Activation Status Indicates whether or not the SkyRouter has been successfully activated on the serving network Network Stability Indicates whether or not the current network connection is of adequate quality to perform an OTA activation 1xRTT Status Panel ECIO A figure of merit Ec Io describing how well the CellRouter can hear forward link the serving network when all other traffic and noise on the same channel is considered Lower numbers indicate a better quality connection A strong small RSSI does not necessarily equate to a low Ec Io value Channel The specific CDMA channel that the CellRouter is currently using to communicate with the serving network EVDO Status Panel Same as the 1xRTT Status Panel only for the EV DO bearer 4 4 2 Ethernet Status Indicates the current LAN side IP address that the CellRouter is using MAC Address is a vendor and machine specific identification code imer mest in Moten serine me comes Ethernet Interface Status i 192 168 1 10 1 DO MOC 0 00 00 Figure 20 27 Part Number IIM2200A Release 1 00 5 Specifications Controller Axis Etrax 100LX MCM 4 16 Linux 2 4 Interfaces Four Port Ethernet Switch RJ
17. ay output interface can be activated by an SMS message or from a button that can be defined on the Advertising screen described in the Services section Appendix A contains schematic information concerning the relay output configuration TR Ctok SkyRoutor Microsoft Internet Explor r Fle Edge Wen Fortes fode Help Om O DES Pan kes Qua O E rz hapi ktex31 hinge netadi tin kg relevo L cot Google visam Gere O Eb szzitsc sc leteenei in Motion y rrpanmg pew mawar Relay Output Configuration Set Relay Output State Used to set the current state of the relay driver circuit The relay driver can be activated and deactivated by changing this setting and pressing update Relay Shut Off Timer The relay driver circuit will revert to its default setting after the number of minutes or seconds specified by this parameter The two second setting is useful for resetting end point equipment 14 Part Number IIM2200A Release 1 00 Allow SMS Control of Relay If Yes is checked the relay driver may be activated by sending an SMS with the command R1 and deactivated by sending an SMS with the command of RO Allow Web Browser Control of Relay If set to yes a button will appear on the Advertising screen to enable and disable the relay driver circuit Text For Web Link To Relay This text will appear on the advertising screen next to the relay activation button 4 3 Services 4 3 1 Password A
18. ble Disable Wireless Routing b Enable Disable inbound IP requests c Name Server Interoperability with UDP or SMS d DDNS Interoperability with BIND or MS Server e Administration web server port address selection f Enhanced IOTA OTA and manual activation g Home Network Selection 3 Relay Contact Closure detection and operation a NO NC detection b SMS or email cry out alarm Part Number 91 601 01 Release 1 00 4 Relay Driver Output a SMS Activation b Web Activation 5 General Administration a Modify Password 6 Status Ethernet Status a Currently Assigned IP Address b Current MAC Address 7 Status CDMA Status a ESN Serial Number Hex and Decimal b Network Assigned IP Address c Telephone Number MIN d Current Network Status Active Inactive e Signal Level RSSD Part Number IIM2200A Release 1 00 2 Connectors Lights Switches and Jumpers 2 1 Switches Referring to Figure 1 there are two switches on the front of the Series 2200A S1 Reset causes a hard reset of unit S2 DFLT is used to completely restore the firmware settings that were included when the product was shipped from the factory To restore factory defaults the unit must be running Press the Restore Defaults inner switch and hold it down for 10 seconds After 10 seconds you will see both the green and yellow lights go off At that time you may either press the reset outer switch or cycle power on the unit Figure 1 2 2
19. connected Figure 3 Part Number IIM2200A Release 1 00 4 Administration Configuration and Status About Addressing Devices connecting to CDMA IXRTT networks are assigned an IP address by the serving network Address assignment may either be static or the unit will be dynamically assigned an IP addresses depending on arrangements that you have made with your wireless network operator Dynamically assigned IP address remain in effect for a period of time assigned by the network operator usually at most a small number of hours IIM s CellRouter includes features that manage the temporal nature of dynamically assigned wireless IP addresses Using the Wireless Configuration screen you can configure your SkyRouter to use a Dynamic DNS DDNS service IIM operates a DDNS test bed that allows our customers to observe the performance and reliability of DDNS with their applications For large scale commercial applications IIM recommends that users configure their own DDNS managed and maintained with the customers ongoing IT operations The CellRouter may also be configured to operate with a standard DNS having Dynamic DNS capabilities Examples of this type of service would be Berkeley Internet Name Daemon BIND and Microsoft Server 2000 and up For detailed information see IIM s TechNote S2200 01 Even if you elect to use a static IP address a DDNS service will add value in two ways First when the networks static addressing assignment fails
20. dministration Used to change passwords and create users Be sure to record this information in a secure location D heen 197 168 1 10 admin bincie_perd cei Microsoft internet Explorer Es File Exit vew Favertes Tos Heb G O MAG Pme dera Gee O GS E WSS Actress Ol resido 168 3 admin briti ps d co gt Enter new username and password ey re eee New User Name New Pas sword Confirm New Password Update Home Figure 9 15 Part Number IIM2200A Release 1 00 4 3 2 Routing and Forwarding Services The Routing and Forwarding Services screen provides two separate but related functions First it allows you to forward WAN side IP traffic arriving on a specific IP Port to a specific Port at a LAN side address In addition to this conventional forwarding feature this screen also allows you to make a Named Service publicly available over the WAN interface In Figure 10 below WAN side UDP and TCP traffic arriving on Port 88 is redirected to Port 80 of LAN address 192 168 1 102 The second function performed by this set up screen to allow named services to be made publicly available to WAN side users Referring again to Figure 10 a service named Ctek SkyRouter Demo San Pedro CA will be advertised or made publicly available Security for this advertised service is left up to the specific service If the Advertising feature is used the Administrative Login screen will no longer greet incoming WAN users i
21. nna must be connected before powering the unit on 3 3 Connecting to the Ethernet Port Administrative Connection For a direct Ethernet connection between a PC connect to any of the Ethernet ports using a standard or reverse Ethernet cable For initial configuration and administration with a PC or workstation IIM recommends that the PC be set to obtain an IP address and obtain a DNS address automatically For Windows PCs make the following settings under the networking control panel LAN Ethernet Connections Windows General Authentication Advanced General Ahemate Configuration Connect using You can get IP settings assigned automatically your network supports thes capably tse you need to ask your network administrator for Reake lt RTLS139 Far PCI Fast Ethernet NIC the appropriate IP eettinge Obtain an IP address automatically O Use the following P address P address PRADA This connecton uses the following items vi ISI Chem for Microsoft Networks f JA File and Printer Shasing for Microsoft Networks Stone mat Obtain ONS serve address automatically Install O Use the following DNS serves addresses Description Preferred DNS serve Akwnate DNS server SAGE Transmission Control Protocol Imemet Protocol The default wide area network protocol that provides communication across diverse interconnecied networks M Show icon in notification xea when
22. nstead they will be presented with a Services screen as shown in Figure 11 ea Routing and Forwarding J fv 4 2 go I i 199 4 t iw N x I Tr SkyFowe 4200 Dema l address 192 159 1 rT Enable 1 Figure 10 Block Inbound IP Traffic From Wireless Network If set to Yes the CellRouter s firewall is configured to block any inbound originated but not response packets from the wireless network WAN This firewall is then selectively modified by the forwarding entries defined through this screen If this parameter is set to No the CellRouter s firewall is disabled Use NAT on all Ethernet traffic to wireless network For normal operation this parameter should be set to Yes In some unique situations you may connect the SkyRouter to a network where you will be given public address to use on your LAN s Ethernet segment In such cases NAT should be turned off NAT is currently required for operation on all US networks such as Sprint Verizon or Alltel Typical environments where NAT would be turned off would be private networks or some types of VPNSs and in these cases the network operator will most likely provide configuration assistance Forward Inbound Port This table allows WAN side packets addressed for specific IP ports to be routed to a specified address on the LAN side Of Local Address Used to specify the LAN side address of the routing operation 16 Part Number IIM2200A Release 1 00 TCP
23. oes two short blinks on every 4 5 seconds Yellow LED off but does two short blinks on every 4 5 seconds In service signal less than 88 active data connection Green LED on but does one short blink off every 4 5 seconds Yellow on In service EVDO or EVDO amp 1xRTT signal less than 88 active data connection Green LED on but does one short blink off every 4 5 seconds Yellow LED on but does one short blink off every 4 5 seconds In service signal greater than or equal to 88 active data connection Green LED on but does two short blinks off every 4 5 seconds Yellow on In service EVDO or EVDO amp 1xRTT signal greater than or equal to 88 active data connection Green LED on but does two short blinks off every 4 5 seconds Yellow LED on but does two short blinks off every 4 5 seconds Part Number IM2200A Release 1 00 2 3 Connectors Ethernet Connectors Connectors are found on the back of the Series 2200A CellRouter Ethernet ports 1 4 are auto polarity sensing and can be used with either a standard Ethernet cable or a reverse cross over Ethernet cable Terminal Block Connector J1 supports three separate functions power relay contact closure detection and the relay driver output The pin out configuration is as follows Pin 1 Din Discrete Input See Appendix A Pin 2 Din Src Discrete Input Source See Appendix A Pin 3 Dout Gnd Discrete Output Ground See Appendix A Pin 4 Dout
24. ommand interface that can be used to perform manual activations or to enter and observe other AT commands as required AT commands Example ATDT are entered in the top field on the Manual Activation screen and the resulting radio and or network status is displayed in the scrolling region below hero ret im Maddow N Manual Activation Process Kern r vou mearan am mano Sutbm Back Figure 17 22 Part Number IM2200A Release 1 00 4 3 5 Applications The CellRouter is capable of installing and managing custom applications The Applications Services screen is the user interface to manage custom applications The individual application release documentation will document the individual applications behavior feresmet m Metre gt User Defined Applications No Applications Currenily Configured Home Figure 18 23 Part Number IM2200A Release 1 00 4 4 Status 4 4 1 Wireless Status The Wireless Status interface provides information on the CellRouter s wireless network connection local operating conditions and predefined information contained within the radio module Wireless status information is presented in two levels of detail summary and detailed Either level can be refreshed updated in real time using the Refresh button at the bottom of the page The Wireless Status interface is display only Wireless Status Summary Screen internet in Motion y ima Wireless interface Status
25. ontrol the home network setting of the CDMA connection effectively limiting the scope of the Preferred Roaming List PRL assigned by your wireless network operator The possible settings are shown below Internet in Motion icra Wireless interface Configuration Network Select 0 Auto 1 Home only 2 IxRTT only 3 1xRTT home only out 5 IxRTT PCS home only twork provided dynamic IP addres xRTT colular only 7 1xRTT celular home only Ename EvDO only 3 EvDO home onl address Mt Far Dem ami O A ririmaco Deer insti n User Name and Password Required for activation on some networks See TechNotes for specific usage Wireless Connection Used to enable disable the wireless WAN connection Part Number IIM2200A Release 1 00 Disabled Turn off WAN connection Enabled Turn off WAN connection Use Network s Dynamic IP Address For most networks this will be the correct selection Use The Following Static IP Address If your selected network is capable of provisioning a static IP address to your application check this box and enter the assigned IP address See TechNotes for network specific set up Enable LCP echo packets Used on some International networks For all US networks LCP echo packets should be turned off meaning this box should be unchecked If you have questions check with Ctek support Select DNS Type Used to select the appropriate protocol for your Dynamic DNS
26. put Interface This screen configures the connection characteristics of the relay input interface and defines the service associated with this interface Currently the relay interface can cause an SMS message to be sent to another wireless device or an e mail message to be sent to any valid email address Appendix A contains schematic information concerning the relay input configuration 3 http 192 168 1 i admin bin cfa relay cgi Microsoft Internet Explorer Fla Et Vew Faveriies Toos Oua E Z search iy aonyeea EF wens harp 192 064 L wader sr ctg relay xg r was y I peg we ea s SMS Dewtinaten Address 357462032 SMS Alon Mossag Aven message from Crohs Update Home Figure 8 Relay Input Trigger Establishes the conditions under which the Relay Service will be invoked Unless it is disabled the relay input is sampled at 1000 millisecond 1 second intervals Disabled Never respond to relay activity On Closure Respond when relay contacts go closed On Opening Respond when relay contacts go open Maximum Trigger Rate This setting determines how often the CellRouter will send a relay event message If the relay event is recurring at a rapid rate this setting will prevent an undesirable flood of messages If Maximum Trigger Rate is set to Always the relay input is operating in edge triggered mode In this mode the CellRouter will invoke its assigned service any
27. sting for compliance with Measurement Requirements CFR 47 Part 22 Paragraph 22 917 b 2 and Part 24 Paragraph 24 238 a WARNING To reduce any possible hazard due to exposure of the human body to electromagnetic radiation per FCC OET Bulletin 65 this device is approved for operation using the antenna provided The antenna installation must provide a separation distance of 20 cm or more between the antenna and all persons to satisfy Maximum Permissible Exposure MPE compliance 29 Part Number IIM2200A Release 1 00 7 Appendix A J gt 30 Part Number IIM2200A Release 1 00 ISCLATED APPLICATION NON ISOLATED APPLICATION Part Number IIM2200A Release 1 00 32
28. tatic IP address as defined in the next section It is recommended that an address of 192 168 1 10 be used The DHCP server will issue dynamic IP addresses to other devices connected to the LAN side IP addresses will be assigned for up to 50 devices Address assignment is sequential in the range of 192 168 1 100 192 168 1 150 11 Part Number IIM2200A Release 1 00 Enable Client Some other device on the LAN side of the network is acting as a DHCP server CellRouter will be assigned a dynamic IP address by the DHCP server DNS Address Source In most cases this parameter should be set to Acquire From Wireless Network In this case when you click on the Update button the Cellrouter will verify that it has been connected to the wireless network and that the wireless network has provided DNS addresses If DNS addresses have been provided they will be displayed in the Primary and Secondary Address boxes If addresses have not been provided you will receive an error indication At that point you should allow the CellRouter to establish a connection with the wireless network so that it can acquire the DNS addresses You should then go back into the Ethernet Configuration screen and click on submit again At this point the DNS addresses should appear If you application requires a specific DNS setting check the User Defined box and manually fill in the DNS IP Address fields below DNS IP Address Primary and Secondary The address of
29. ternet Protocol IP address assigned to this CellRouter by the serving wireless network If this field is blank a connection does not currently exist Band The range of spectrum that this unit is operating on Options are PCS or Cellular Call Status Indicates the current status of network registration Idle Not registered disconnected a unit that is idle will not have a valid IP address Connec ted Registered and active on the network A connected unit will have a valid IP address Dormant Registered but inactive Wireless data connections transition to the dormant status after a brief period of inactivity The dormant state is a normal condition Roam Status Indicates the networks view of the current geographic location of your CellRouter The possibilities are Not Roaming Home Roaming or Blink Roaming An indication of Roaming may or may not impact your data transmission costs Charges are a function of your rate plan not necessarily linked to the networks notion of roaming Temp Alert Indicates the status of the radio s internal temperature sensing Options are Temp OK Over Temp Disconnect or Over Temp Shut Down Temp OK indicates that the sensed temperature is less than 85 degrees Centigrade A Temp Disconnect indicates that the radio is attempting cool down procedures and a Over Temp Shut Down indicates that cool down procedures have failed and the radio has shut down to protect itself 25 Part Number
30. time that the input transitions to the selected state So if ON CLOSURE is selected an SMS is sent every time that the contacts close This means that once closure is sensed there can be no other closure event until the contacts are first sensed to be open All other modes where Max Trigger Rate has a time value are level sensitive So it the contacts close an SMS is sent and then the state of the relay input is ignored for a defined period of time For instance if Max Trigger Rate is set to 5 minutes an SMS is sent and then the relay input is sampled again in 5 minutes If the contacts are still closed another SMS is sent If the relay input is not closed SkyRouter reverts to monitoring the relay every second 13 Part Number IIM2200A Release 1 00 SMS Destination Address The MIN mobile phone number or email address to which the SMS message will be sent MIN must be 10 numeric characters with no spaces or punctuation Any email address in the form Anything O Any Domain will be accepted SMS Alert Message The text of the message to be sent when the relay interface activates Limited to 100 characters maximum Only printable ASCII characters in the range of 32 126 decimal 20 7E hex can be included in the message 4 2 4 Configuring The Relay Output Driver Interface This screen configures the connection characteristics of the relay output interface and defines the service associated with this interface Currently the rel

Download Pdf Manuals

image

Related Search

Related Contents

Le dieu du carnage Andrea Jonsson  Whirlpool EH070CFXCO User's Manual  Silvercrest Model M-11 Floor Plan  LUBRICACIÓN Y MANTENIMIENTO  RCA RCR504BR remote control  Manual do Usuário DC6393BR  Jotul Woodstove F 400 User's Manual  Huffy NCS102 User's Manual  as a PDF  Tuberías plásticas en la edificación: Manual técnico  

Copyright © All rights reserved.
Failed to retrieve file