FS100 All-in-One System Lite / Pro User `s Manual
Contents
1. Federal Communications FCC Statement This device complies with FCC Rules Part 15 Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesirable operation This equipment has been tested and found to comply within the limit of a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by switching the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the interference receiving antenna Increase the distance of separation between the equipment and interference receiver Connect the equipment to a power outlet on a circuit different from that to which the interference receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING The2. use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Tested To Comply With FCC Standards Ro H S FOR HOME OR OFFICE USE LISTED iii Chapter 1 Welcome Overview of FS100 Rear View OSD Control Buttons Features Unpacking Chapter 2 Getting Started Pre installation Notice Default Setting Limitations Hardware Installation Installing the Adapter and Internet for Lite type Installing the Adapter and Internet for Pro type Installing the Customer Display for Lite type Installing the Customer Display for Pro type Installing the 2nd display for Pro type only Installing the MSR LCD Operating Angle Appendix Technical Information Specifications Frequently Asked Questions FAQ iv oOopoN Bm ComMDmMNDAAST 10 10 11 12 12 13 13 15 i Welcome Congratulations on your purchase of this POS terminal Your easy to use POS terminal is designed to help you enhance your business flexibility by offering a superior customer experience Pro Powerful expansion capability Dual display for advertising Chipset HDD 2 57 3 5 x1 CF memory card DOM Disk On Module Storage devi
3. FS 100 All in One System _ Preface About this Manual Thank you for purchasing our FS100 All in One System This terminal offers highly enhanced features with easy connection to various optional devices for optimal performance This user manual describes how to setup and connect your terminal Copyright Copyright 2006 All rights reserved This product and related documentation are protected by copyright and are distributed under licenses restricting their use copying and distribution No part of this documentation may be reproduced in any form by any means without prior written authorization of the manufacturer and its licensors if any Safety notices AN Before You Proceed Read the safety notices and the User Manual carefully before using the product Keep the box and packaging in case the product needs to be shipped in the future Follow the product and warning label instructions Any changes or modifications that do not follow the instructions in this manual will void this product s warranty A Power Supply Safety Notes To avoid electric shocks disconnect the power cord from the electrical outlet before relocating the system Make sure the voltage of the power outlet conforms within voltage range of the terminal Failure to comply may cause the electric shock or damage to the terminal If you are not sure of the electricity voltage that you are using contact your local electricity company To avoid fi
4. M1 COM2 COMS3 COM4 COM 5 COM 6 IRQ 4 IRQ3 IRQ5 IRQ 10 IRQ5 IRQ 10 Chapter 2 Getting Started Preset voltage setting for MSR 1 The MSR default setting is ISO Track 1 amp 2 For customized track settings advise the manufacturer before production 2 In event of any requirement to change the setting of the MSR run Setting utility in the driver CD provided in the accessory package 3 The normal swiping card speed of the MSR is 10 to 100 cm sec based on the ISO 7812 standard Voltage Output device interface DC 12V 0 5A 12V 0 5A interface interface Qn PIN of DB 9 On Mother Card DC 12V 0 5A DC 12V 1A interface 9m PIN of DB 9 Interface Board DC 12V 0 5A DC 12V 1A RJ 45 Interface Board DC 12V 1A DC 12V 1A OM 6 for Cash Drawer Taternal connector DC 12V 1A DC 12V 1A driving Pulse DC 24V 1A DC 24V 1A DC 12V Powered USB for Bottom side O Interface Bondy DEBY LSA DC12V 2 5A DC DC 24V Powered USB for Bottom side O Interface __ Board DENA 24V 2A DC 12V k Bottom side O 2na LCD Monitor Power Interface Board DC12V 15A FDC 24V Printer Power Bottom side onnector Hosiden Interface Board DC 24V 1 5A DC 24V 2A Note O None of the COM Port current loading should exceed DC 5V 3A DC 12V 2A O DC 12V 24V powered USB should not be used with 12V DC plug and 24V Hosiden at the same time O0 When 2nd Display uses 12V DC plug the thermal printer can NOT use the 24V Chapter 2 Ge
5. ces 1 Touch amp MSR I F included 3 Touch amp MSR I F included USB port 3 USB Ver 2 0 5 USB Ver 2 0 DC Output for DC 12V amp DC 24V plug peripherals Chapter 1 Welcome Rear View The rear panel view with the input and output ports is shown in the illustration Upper I O Ports Lite Pro DESCRIPTION Line Out LAN port USB port x 2 COM 3 CF Card slot 2na VGA port Pro only oO nR Lower I O Ports Pro only DESCRIPTION COM 5 RJ45 Cash Drawer Port Chapter 1 Welcome OSD Control Buttons CATEL w TELLI OO OO O 6 5 4 3 2 1 FUNCTION Press the Power button to start up the system Press the Power button for 4 seconds to shut down the system from hardware Press the Power button and Brightness button for 4 6 seconds to reset the system from the hardware 2 Power LED Red Standby mode Green System start up 3 Brightness Press the Brightness and Brightness button to active the 4 Brightness adjustment mode then press Brightness and Brightness button for brightness adjustment The setting will be saved after releasing the button for 6 seconds 5 Speaker Press the Speaker and Speaker button to active the 6 Speaker adjustment mode then press Speaker and Speaker button for brightness adjustment The setting will be saved after releasing the button for 6 second
6. e Touch POS System Processor Supports VIA Eden CPU up to 1 0 GHz Memo 200 pin DDR RAM 1 up to 2GB DDR333 400 System Core North Bridge VIA CN 700 Chipset South Bridge VIA 8237R BIOS Award BIOS with enhanced ACPI 1 0 PnP APM DMI ESCD PCI bus 2 1 On Now DRAM ECC AGP 3D VIA AGP4X graphics core share memory from 8MB up to Graphics 64 MB Dual VGA output Dual view on North Bridge Chips Supports 3D 2D graphics accelerator NT 4 0 5 0 Windows 95 98 2000 XP_ utility APM ACPI 1 0 Direct 9 0 VPE MPEG2 Parallel Port One LPT port SPP EPP ECP IRQ and address selectable by BIOS setup Serial Port Total 6 COM port on board IRQ selectable by BIOS setup Output on 9th pin by jumper selector Each voltage output with poly switch protector USB Total 5 USB port USB 2 0 support One USB port V 2 0 located on the front panel Two USB port V 2 0 located on the rear panel Two USB port V 2 0 on extended base optional Enhance PCI On board PCI bus master IDE1 2 support Ultra IDE DMA 66 100 133 13 Appendix Technical Information ITEM SPECIFICATION Serial ATA One Serial ATA HDD ports Port Thermal One heat sink for CPU heat pipe and North Bridge Chip Solution Compact Flash One bootable compact flash card socket Type I II Card Cash Drawer One cash drawer port with status sensor EPSON ESC Pin Port define System Power DC 24V 5A 120W external power adapter with internal DC to DC power inverter AC Power AC 90
7. ocedures below to install the Customer Display 1 Plug the VFD RJ 45 connector of the Customer Display into the COM5 port 2 Install the Customer Display and the cover stand in place with three M3 screws 10 Chapter 2 Getting Started Installing the 2nd display for Pro type only To install the 2 4 display onto the FS100 Terminal do the following 1 Connect the DB 15 cable to the connector on the back of the FS100 Terminal LCD screen and arrange the cable in the clamp as shown mm DB 15 connector Cable clamp 2 Replace the base cover Connect one end of the DC 12V adapter cable to the base and allow the other end of the cable pass through the hole on the 2na Display cover stand DC 12V adapter cable 2na Display cover stand 3 Affix the 2na Display cover stand to the base with three M3 screws Next connect the other end of the DC 12V adapter cable and the DB 15 cable to the 2na Display 11 Chapter 2 Getting Started 4 Install the 2 4 Display and lock it to the stand with four M3 screws Installing the MSR To install the MSR onto the LCD display do the following 1 Attach the MSR device jack to the MSR socket on the side of the LCD display 2 Affix the upper and lower MSR wires firmly to the slots on the side of the LCD 3 Lock the MSR securely on the LCD display with two M3 screws 12 Appendix ITEM SPECIFICATION Model Name FS100 All in On
8. r vendor immediately FS100 Touch Customer Display 2nd Customer Display Terminal optional optional Magnetic Stripe Reader AC Power Cord Power Adapter optional Accessory Package 1 Screws black for MSR x 2 2 Driver CD disc 3 User s Manual 4 DC24V power cable Pro only 5 DC12V power cable Pro only 6 PS 2 COMBO Y cable 7 USB rubber cove 8 Cable clamp 9 P E sheet Chapter 2 Getting Started This chapter describes how to install the optional accessories on your FS100 Touch Terminal for optimal serviceability Before you start installing your FS100 please read the following notices carefully 1 The FS100 does not support PCI slot 2 Do not plug in or unplug any interior devices such as memory module or any function card when the ATX PSU is powered on 3 The LAN chipset uses RTL 8139 810x family network adapter The Terminal has be built in the PXE Boot ROM function within the BIOS to execute Boot ROM already 4 For installation and compatibility using the DDR RAM Module from the original manufacturer is recommended 5 The USB device connector is Hot Swap Do not plug in or unplug any connectors other than USB devices when the power is on 6 The spill proof design of FS100 conforms to IP 43 standard 7 Do not insert or remove any devices or components from the FS100 while the power is on Default Setti ng Default settings for FS100 Touch Terminal serial ports CO
9. re or electric shocks do not overload electric power outlets Protect the power cord from being walked on or pinched particularly at plug convenience receptacles and the point where they exit from the apparatus Operating Instructions Keep this manual for future reference Keep this equipment from moisture and dust Place the equipment on a stable surface before setting it up O If there is any If the following situation arise notify a qualified service technician immediately gt The power cord or plug is damaged gt Liquid has been spilt on to the equipment gt The equipment has been dropped and damaged gt The equipment does not function normally Do not block any ventilation openings to prevent the equipment from overheat Do not leave the equipment in a non air conditioned environment where the storage temperature may go above 60 C 140 F as this can cause damage to the equipment Maintenance Gently wipe screen with a clean soft hair lens brush or a lint free cloth 0 Do not apply pressure to the screen while cleaning Do not spray any liquid directly onto the screen or the casing of the FS100 Terminal Chemical cleaners have been reported to cause damage on the screen of the FS100 Terminal Warning and Attention The technical descriptions and specifications of the equipment are subject to change without notice For safety reasons wear gloves when assembling the product ii Preface
10. s Note Press the Brightness and Speaker to restore the factory default setting Chapter 1 Welcome This POS terminal comes equipped with the following features Noise free Low power consumption Saving cost of ownership Compact size Aesthetic design Dust water proof WEPOS XPE solution Environment protection Higher stability The fan less noise free design of the FS100 is ideal for noise intolerant environment ULV Ultra Low Voltage design of the device is embedded with a unique chip set and CPU renders power saving function Modular design provides the owner with the following benefits a cost effectiveness b customization flexibility and c easy maintenance Slimmest in the POS industry standard 24 mm This elegant economic POS system features a sleek compact design base that saves counter space and adds appeal to the service environment FS100 series features a highly durable rigorously tested design that is reliable and dependable in rugged environments Solution is recommended to be bundled with embedded solution for high performance and other added values Environmental friendly RoHS compliant product The FS100 has a longer overall system MTBF to provide a higher stability during operation Chapter 1 Welcome Before setting up your FS100 check that the package contains the following items If any of the items are missing or damaged contact you
11. to 264V Full Range Source System Trigger System front side tact switch ATX Trigger below the LCD Control display with bottom Ethernet Port Realtek RTL8100C Ethernet chip on board 10 100 Mbps Intel Ethernet chips on board 10 100 base T Gigabyte Auto extendible ACPI NT 4 0 5 0 NDIS5 Remote boot ROM for NT 4 0 Enable or disable by BIOS setup Audio VIA VT 1612A AC97 CODEC on board Keyboard PS 2 Mouse PS 2 Wall Mount VESA standard 100mm System Size 350mm L x 350mm W x 350mm H min height when folded 160mm S W DOS OS2 V2 1 SCO XENIX V2 3 2 SCO UNIX Compatibility V3 2 NOVELL WIN 3 1 95 98 2000 XP NT4 0 Operation 0 C to 40 C without HDD up to 50 C Temp Storage Temp 25 C to 70 C Optional ISO Trick 1 2 3 Magnetic Stripe Reader Device ITEM SPECIFICATION Smart Card Reader mmm ___ 20 column 2 lines VFD Customer Display Optical Finger Print Sensor 10 4 or 12 1 LCD Customer Display 32 Keys Programmable POS Keyboard Note Specifications are subject to change without notice Question 1 Why does the system appear unstable after updating BIOS Answer Load optimized defaults or load SETUP Default after flashing BIOS If the system remains unstable clear CMOS to solve the problem Question 2 How do I clear CMOS Answer To clear CMOS do the following 1 Turn off power and switch off the power adapter 2 Remove the jumper from clear CMOS 2 3 PIN and insert the j
12. tting Started Installing the Adapter and Internet for Lite type To install the adapter and Internet cable for Lite type do the following 1 Connect the Internet RJ 45 cable and the power cable to the connectors and arrange the cables in the clamps as shown RJ 45 connector Power adapter connector 2 Replace the extension base cover and affix it to the base with two M3 back screws Chapter 2 Getting Started Installing the Adapter and Internet for Pro type To install the adapter and Internet cable for Pro type do the following 1 Take out the cable clamps from the accessory package and attach them to the position as shown Connect the Internet RJ 45 cable and the power cable to the connectors and arrange the cables in the clamps RJ 45 connector Power adapter connector Cable clamp 2 Replace the extension base cover with two M3 screws and then affix the stand cover to the base with three M3 screws Chapter 2 Getting Started Installing the Customer Display for Lite type Follow the procedures below to install the Customer Display 1 Connect the VFD DB 9 cable to the connector as shown 2 Replace the base cover and affix it with two M3 screws 3 Attach the Customer Display to the base of the FS100 Terminal with two M3 screws 4 Lock the Customer Display to the customer display pole bracket with two M3 screws Installing the Customer Display for Pro type Follow the pr
13. umper to clear COMS 1 2 PIN 3 Remove the jumper from clear CMOS 1 2 PIN and re insert the jumper to clear CMOS 2 3 PIN 4 Switch on the power again 5 Press Delete to enter COMS setting and load optimized defaults 6 Save changes and reboot the system Question 3 How to use Boot Menu Answer To use the Boot Menu do the following 1 Press F9 to enter the Boot Menu 2 Select the Boot device from the Boot Menu 15
Download Pdf Manuals
Related Search