Manual for Datalogic Jet single vehicle cradle.
Contents
1. ACCESSORIES 94A051013 WIN NET VEHICLE POWER CAB Cable containing an 8A slow blow fuse for powering CRADLE the vehicle cradle from the car cigarette lighter 94ACC1306 ADJUSTABLE ARM KIT FOR positionable arm for mounting the cradle in the VEHICLE CRADLE vehicle TECHNICAL FEATURES Power Supply Consumption with PDA Quiescent Consumption without PDA Indicators Charge Time when PDA is of Communication Features Interface RS232 Baud Rate RS232 up to 115200 b sec Working Temperature Storage Temperature 20 to 70 C 4 to 158 F Humidity Degree of Protection IP30 0 3 Vibration Resistance EN60068 2 64 frequency range 5 1000 Hz acceleration RMS 3 1 g initial slope 26dB oct 5 10 Hz final slope 3dB oct 10 1000 Hz Shock Resistance EN60068 2 29 25g 6ms duration 500 shock impacts per axis Mechanical Features Dimensions 240 x 79 x 48 mm 9 45 x 3 1 x 1 9 in Weight about 200 g 7 05 oz Battery must be charged at a temperature ranging from 0 to 45 C 32 to 113 F for screw mounting FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use this equipment The device complies with PART 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference wh2. ailable Loudspeaker model vocal communication available through either the built in speaker and microphone or a hands free head set Standard model communication available only through hands free head set MOUNTING THE DATALOGIC JET VEHICLE CRADLE The Datalogic Jet Vehicle Cradle can be mounted to the desired surface using either the 4 adhesive Velcro strips or the 4 screws IN Oo 0 B LI A B Sais q Figure 2 Mounting with Velcro Strips Figure 3 Mounting with Screws Mounting with Velcro Adhesive Strips see Figure 2 This procedure is suggested when mounting the cradle on flat surfaces 1 Select a mounting location allowing an easy access to the cradle connector panel 2 Carefully clean the adhesive strip seat of the rear of the cradle see Figure 1 to remove any impurities that could reduce adhesion 3 Remove the protection film from the adhesive side of two of the available Velcro strips and stick them on the cradle surface see Figure 2 A 4 Remove the protection film from the adhesive side of the two remaining Velcro strips and stick them on the vehicle surface smooth and clean for better adhesion see Figure 2 B 5 Affix the cradle to the vehicle surface Mounting with Screws see Figure 3 This procedure is suggested when mounting the cradle on curved surfaces It is possible to use 4 self tapping screws or 4 screws with nuts according to the user s needs 1 Sel
3. ect a mounting location allowing an easy access to the cradle connector panel 2 Insert the four screws in the cradle mounting holes see Figure 3 A 3 One or more spacers can be used optionally to compensate for mounting to irregular surfaces see Figure 3 B 4 Affix the assembly to the vehicle surface by means of the four screws tighten with nuts if not using self tapping screws POWERING THE DATALOGIC JET VEHICLE CRADLE Once the cradle has been mounted it is necessary to prepare the power cable termination to connect the cradle to the vehicle power source Brown wire connect to a V 10 to 32 Vdc vehicle power source Blue wire connect to the vehicle ground wire or chassis ground Green Yellow wire not to be connected For connection to the vehicle power source it is possible to use the in line fuse with holder supplied with the cradle Verify that the a 8 A slow blow fuse is contained within the holder then splice it to the end of the brown wire of the cable Make the distance between fuse holder and power connection point as short as possible and apply a caution label on the fuse holder Figure 4 Fuse Holder _ Brown Wire Once the power cable termination has been completed it is possible to connect the Datalogic Figure 5 Fuse Holder Connection Jet Vehicle Cradle to the vehicle power INSERTING THE DATALOGIC JET INTO THE VEHICLE CRADLE For correct functioning insert t
4. he PDA into the cradle by lightly pushing it towards the upper part of the cradle retaining clip Then push it down until the retaining clip clicks When the cradle is powered insert the PDA and the green LED will turn on If the PDA is not inserted the LED remains off while the cradle is still powered Figure 6 Inserting the PDA into the Vehicle Cradle CONFIGURING DATALOGIC JET PDA FOR VOCAL COMMUNICATION By default vocal communication takes place through the Datalogic Jet PDA integrated loudspeaker and microphone Once inserted into the vehicle cradle the communication has to be managed by the cradle itself Thus the PDA must be configured through the volume settings applet available in the Windows CE NET control panel to correctly manage the communication refer to the Datalogic Jet User s Manual for more details Vocal Communication requires Datalogic Jet PDA SW version 1 40 or later CONNECTION The Datalogic Jet Vehicle Cradle can be connected to a host by means of an RS232 interface RS232 Connection The Datalogic Jet Vehicle Cradle can be connected to the host by means of any standard null modem cable A 9 pin female D Sub connector must be connected to the RS232 port of the cradle Once the host has been turned on insert the Datalogic Jet PDA into the cradle Pin 9 of the Vehicle Cradle RS232 connector normally not connected in null modem cables supplies regulated 5 Vdc 5 500 mA max
5. ich may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WEEE COMPLIANCE pid 822000601 Rev C DATALOGIC Datalogic Jet Vehicle Cradle The Datalogic Jet Vehicle Cradle allows charging the Datalogic Jet PDA battery and holding it securely in your vehicle It also functions as a serial communication interface between a Host typically a Laptop PC and the RS232 contacts on the PDA A Velcro Adhesive Strip Seats B Ext Microphone Headset Jack C LED Indicator D Microphone E PDA Contacts F Mounting Holes G Power Connector Jack H RS232 Connector Loudspeaker Figure 1 Datalogic Jet Vehicle Cradle External microphone headset jack microphone and speaker allow managing a vocal communication see related paragraph on next page In particular two different cradle models are av
6. power A To Vehicle Battery j Figure 7 RS232 Connection A Datalogic Jet Vehicle Cradle C Host Computer B Standard Null Modem Cable
Download Pdf Manuals
Related Search