The Edge EZ Module
Contents
1. H A DATED PROOF OF PURCHASE TO THE PLACE OF PURCHASE WITHIN SIXTY 60 DAYS FROM DATE OF PURCHASE FOR A FULL REFUND THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS ITS TERMS AND CONDITIONS Legal in California only for racing vehicles which may never be used upon a highway Edge EZ User Manual Edge Products AFTERMARKET PRODUCTS AND YOUR VEHICLE S WARRANTY Many of our customers ask Will your product void my vehicle s manufacturer s warranty While the answer is straightforward from a legal standpoint we also want to educate our customers and after market consumers on some industry realities and offer some common sense precautions to minimize your risk Consumers of aftermarket products are protected by The Federal Magnusson Moss Warranty Act The Act states that if something breaks on your car and you take it in for warranty repair the dealer must honor your warranty unless they can prove that whatever modifications you have added to your car actually caused the problem Please keep in mind that towing in anything higher than level two and hard driving in level three is not recommended While as a consumer you have strong legal protection with regards to your vehicle s warranty there is also a practical reality that different automotive manufacturers and dealers have greatly varying views on aftermarket products in particular those that produce horsepowe2. ad these instructions completely so that you understand each step prior to installation The Edge EZ Module This picture shows the Edge EZ Module with the harness cable Edge EZ User Manual Edge Products Module Installation The Edge EZ Module can mount on the flat black plastic fuse box cover located in the engine compartment right in front of the battery on the driver s side Attach the module to the top of the fuse box using the supplied VELCRO strips allowing enough harness movement for removal of the cover Harness Connector Your EZ module may be equipped with a harness that can be disconnected at the EZ module itself See figure 1A It is important to make sure that your EZ module is always connected to the harness when the wiring harness is connected to the truck otherwise the truck may not run properly or may trip engine codes FIGURE 1A Important The truck must be turned off and the keys pulled out of the ignition for at least one minute prior to installation or removal of the connectors and module 1 Remove the plastic engine cover by taking off the yellow oil cap Replace the yellow oil cap once the cover is off Edge EZ User Manual Edge Products MAP Manifold Absolute Pressure Connection 2 Disconnect the stock wiring A harness connector at the MAP sensor The MAP sensor is located on top of the of the intake manifold towards the rear of the engine on the driver s si
3. de The intake 3 manifold is located on top of the engine It may be necessary to move the plastic race that holds the harness on top of the engine up in order to reach the Map sensor connector Plug the supplied MAP sensor connector into the stock engine MAP sensor and the stock engine wiring harness connector into the supplied MAP sensor connector Fuel Pressure Sensor Connection 3 Disconnect the stock wiring harness at the sensor located on the main fuel rail on the driver s side towards the rear of the engine Plug the supplied pressure sensor connector into the stock pressure sensor on the engine and the stock engine wiring harness connector into the supplied pressure sensor connector 4 Run the wire with the switch into the cab of the truck so the switch is in a convenient but safe place Final Inspection and Operation 5 Recheck all connections fittings and fasteners for a properly secure installation 6 Using the supplied wire ties secure the wiring harness from possible damage from moving engine parts 10 Edge EZ User Manual Edge Products Adjusting Power Levels The Edge EZ Module offers 2 levels of power beyond stock The power from the Edge EZ Module begins by plugging the module into your Jeep The power levels are adjusted by changing the in cab switch position to the level you need Adjusting power levels on an EZ module has never been EZier Refer to the power level switch pic
4. er levels and the Exhaust Gas Temperature EGT readings and what they mean As mentioned earlier the EGT tells you how hot the exhaust gases are in the exhaust manifold coming from the engine This is important because you shouldn t let them run for long periods above 1350 F The higher the level the more fuel is fed to the engine and potentially the higher the EGTs Since towing is harder on the engine and the transmission we recommend that you tow in level 1 for a load This will protect you from putting too much stress on the engine and transmission Level 1 is a good all around mode allowing for better economy and better performance while not stressing the engine and transmission We recommend that you run your truck in level 1 or lower for your normal daily activities Technical Support 888 360 3343 To expedite your support call please have the part number version number and Date of Manufacture ready prior to calling support
5. ness for any product s purpose productiveness or any other matter of SELLER s product sold herewith The SELLER shall be in no way responsible for the product s open use and service and the BUYER hereby waives all rights other than those expressly written herein This Warranty shall not be extended or varied except by a written instrument signed by SELLER and BUYER The Warranty is Limited to one 1 year from the date of sale and limited solely to the parts contained within the product s kit All products that are in question of Warranty must be returned shipping prepaid to the SELLER and must be accompanied by a dated proof of purchase receipt All Warranty claims are subject to approval by Edge Products Inc Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in diagnosis for defects removal or reinstallation of this product or any other contingent expenses If the BUYER sends back a failed unit that is out of warranty and chooses to buy a refurbished unit the refurbished unit will only carry a 60 day warranty If the BUYER purchases a new unit at a predetermined discounted rate it will have the standard 1 year warranty Under no circumstances will the SELLER be liable for any damage or expenses insured by reason of the use or sale of any such equipment IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT THE BUYER MAY PROMPTLY RETURN THIS PRODUCT IN A NEW AND UNUSED CONDITION WIT
6. r such as performance enhancement chips and intakes There are dealers and manufacturers out there that will use the presence of a horsepower upgrade to void your vehicle s warranty They will do this regardless of whose box or chip you are using Any aftermarket company that does not acknowledge this is misleading you The bottom line is that while the law protects the consumer and provides for enforcement of the warranty it is very difficult for most people to hire an attorney and fight a voided warranty Edge recommends that you always disconnect and remove your module when you take your vehicle to a dealer for warranty work in order not to interfere with Diagnostic equipment Edge EZ User Manual Edge Products This warranty is void for any new products purchased through auction websites Warranty is valid only for new products purchased through Authorized Dealers proof of purchase required for all warranty claims All Edge modules and programmers are built to operate with OEM calibrations When you take your vehicle to a service center they may by your request or otherwise update your vehicles calibrations Therefore it is important that you return your vehicle to stock before taking it in for service Edge updates its active products i e those currently being manufactured to work effectively with updated OEM calibrations However this process can take some time as Edge is not always made aware of calibration changes made b
7. the other Edge power modules is that they were created for towing That is why Edge built them and why we keep making them better Let s assume that in a stock Jeep you would pull your 2 0001b load up the grades in 3 gear Your EGT Exhaust Gas Temperature may run at about 1200 F With the EZ module on level 1 you have effectively increased the horsepower by 10 and the torque by 15 Foot pounds That is like adding a fifth horse to pull a four horse carriage That is representative of how much your power has increased That means you will be running at a lower rpm and your EGT has decreased And best of all you are going faster and the truck may have already shifted into 4 gear Power level 1 is designed to match fueling with any additional upgrades you may have done to your vehicle Power level 2 should never be used while towing In hot weather when the vehicle is warmed up and while driving in stop and go traffic level 2 should only be used for a few minutes Level 2 is designed to take advantage of the built in safety margins the manufacture needs to add in order to make sure your vehicle can tow at its maximum capacity When driven responsibly and used with an EGT gauge level 2 will not stress the stock engine or transmission as long as you are not towing or driving in hot weather with stop and go traffic for more than a few minutes Edge EZ User Manual Edge Products Exhaust Gas Temperature Now let s talk about the different pow
8. ture for position and power level selection 11 Edge EZ User Manual Edge Products Power Levels Expected output power and torque The following power gains are representative of an actual test vehicle Power gains may vary somewhat on a different vehicle or in different geographic settings Horsepower Torque Level 1 Stock Stock Level 2 10 15 Level 3 23 32 Edge EZ User Manual Edge Products How to Use Your Edge EZ Module Using your Edge EZ Module This section is to help you use the Edge EZ module effectively and add enjoyment to your diesel truck experience The first thing you will probably notice especially if this is your first time driving a diesel Jeep with a performance module is that you will experience more power quicker take offs better passing and acceleration and even better fuel economy Level one is specifically designed to maximize fuel economy improvements Another thing you may notice is that your Jeep is suddenly a lot more responsive to drive Now a word of caution normally driving the stock Jeep you have a feel for how fast you are going in each gear but that changes with the EZ module You may find yourself doing 55 in a 35 mph zone or taking corners too fast Be cautious and be aware that there may be an adjustment period to your new found power Towing What about towing What can this do for you when you are towing The great thing about Edge EZ Module and all
9. y 2005 2006 Jeep Liberty CRD Edge EZ Module Installation Instructions and Manual OLD P N EZJ1000 NEW P N 30500 Edge EZ User Manual Edge Products 2007 Edge Products All rights reserved Edge Products 1080 South Depot Dr Ogden UT 84404 1 888 360 3343 www edgeproducts com Manual Version 3 2 Edge EZ User Manual Edge Products Table of Contents DISCLAIMER OF LIABILITY 4 LIMITATION OF WARRANTY 4 About the Jeep CRD EZ 7 Jeep 2 8LTurbo Diesel EZ Installation 8 Supplied Items 8 Tools Required 8 This picture shows the Edge EZ Module with the harness cable 8 Module Installation 9 MAP Manifold Absolute Pressure Connection 10 Final Inspection and Operation 10 Adjusting Power Levels 11 Power Levels 12 Expected output power and torque 12 How to Use Your Edge EZ Module 13 Using your Edge EZ Module 13 Towing 13 Exhaust Gas Temperature 14 Technical Support 14 Edge EZ User Manual Edge Products THIS IS A HIGH PERFORMANCE PRODUCT USE AT YOUR OWN RISK Do not use this product until you have carefully read the following agreement This sets forth the terms and conditions for the use of this product The installation of this product indicates that the BUYER has read and understands this agreement and accepts its terms and conditions DISCLAIMER OF LIABILITY Edge Products Inc and its successors distributors jobbers and dealers hereafter SELLER shall in no wa
10. y be responsible for the product s proper use and service THE BUYER HEREBY WAIVES ALL LIABILITY CLAIMS The BUYER acknowledges that he she is not relying on the SELLER s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof and the BUYER hereby waives all remedies or liabilities expressed or implied arising by law or otherwise including without any obligations of the SELLER with respect to fitness merchantability and consequential damages or whether or not occasioned by the SELLER s negligence The SELLER disclaims any warranty and expressly disclaims any liability for personal injury or damages The BUYER acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the BUYER agrees to indemnify the SELLER and to hold the SELLER harmless from any claim related to the item of the equipment purchased Under no circumstances will the SELLER be liable for any damages or expenses by reason of use or sale of any such equipment The SELLER assumes no liability regarding the improper installation or misapplication of its products It is the installer s responsibility to check for proper installation and if in doubt contact the manufacturer LIMITATION OF WARRANTY Edge Products Inc hereafter SELLER gives Limited Warranty as to description quality merchantability fit
11. y the OEM In the case of discontinued products Edge cannot ensure that your unit will work effectively if you take your vehicle to a dealership and you are given by your request or otherwise a new calibration Edge EZ User Manual Edge Products About the Jeep CRD EZ Introduction Thank you for purchasing the Edge EZ Module for the Jeep CRD 2 8L Turbo Diesel The Edge EZ module has been developed and produced from the highest quality materials available to ensure the best performance for years to come If you have any questions please contact Edge Products We will be very happy to answer your questions about our complete product line e The Edge EZ Module is an add on Engine Control Module ECM for the Jeep CRD 2 8L Turbo Diesel Engine that offers additional features not available on a stock engine Since it is an add on ECM it uses all the factory data and then enhances the factory settings to optimize your truck s performance The EZ module offers a power increase over stock throughout the RPM range but the power is most noticeable in low to midrange RPM s This greatly improves drivability and towing performance Transmission downshifting is greatly reduced especially while passing or towing Edge EZ User Manual Edge Products Jeep 2 8LTurbo Diesel EZ Installation Supplied Items 1 Edge EZ Module 2 Three Wire Ties 3 Two Velcro Strips Tools Required None Please re
Download Pdf Manuals
Related Search