Mood Light Motion INSTALLATION GUIDE V0.5
Contents
1. 1 Mood Light Motion INSTALLATION GUIDE V0 5 Cover Mood Light Motion Ta p n qe we P ops ques INTRODUCTION INSTALLATION SAFETY AND OPERATION SYSTEM CONFIGURATION CARE AND MAINTENANCE TECHNICAL SPECIFICATION TROUBLESHOOTING WARRANTY STATEMENT www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 12 13 15 16 17 17 20418 tr ae orn 1 INTRODUCTION 1 The Mood Light Motion interactive lighting panels combine LED lighting with motion sensing technology to create stunning interactive architectural lighting solutions Each module is a stand alone system but more can be added to create any size or shape up to 255 modules with auto addressing Different surface materials options available Features 16 RGB LEDs 16 Capacitive sensors Plastic UL 94 VO rated fire retardant housing 24V DC nominal Integrated Controller www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CH2. Diameter as specified by cable manufacturer Bending radius for conductors Note the minimum bending radius for conductors gt 1 5mm2 Pull forces on the contact points can be avoided by proceeding as follows a Bend the wire as required Minimum FIG 3 a Bending Radius Cable Bending www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 7 of 18 1 2 3 On Site Installation e DO NOT attempt installation in wet or severe weather conditions DO NOT leave and expose any Mood Light Motions or power sources unconnected under wet raining or snowing environment e failure induced by stressed damaged cables during or after installation will not be under warranty by Traxon Technologies ALWAYS keep the cables protected from sharp objects and ensure no damage is generated on the cable 2 3 1 Wall Installation 1 Attach 2 plate joiner on each side where adjacent mounting plates will be attached Fix the rear mounting plates to the wall or surface using the 8 fastening holes The bottom mounting plate is attached as an example FIG 4 Mounting Rear Mounting Plate www traxontec
3. bins according to different preset parameters such as forward driving voltage illumination etc Whereas binning is a sorting function it is not a correction process Inherent variability in the manufacturing process always results in different binning distributions according to different production lots Traxon uses automatically binned LEDs on its products thereby minimizing output variations within the model range www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 16 of 18 TROUBLESHOOTING Caution Ensure power supply is OFF when disconnecting connecting cables Problem Cause Possible Solutions Product does Incorrect power e Check Mains Power NOT light up connection e Check power supply leads and wire after installation connections e Ensure output wires are connected with proper polarity Shadowing Light source covered e Check for cables wires or unwanted debris covering LED light source Modules are Excess products e Ensure the power supplies are not dim connected overloaded due to an excess of products connected Flickering Incorrect power input e Ensure the input voltage is correct Excess products Ensure the power supplies a
4. populating the wall Connect the jumpers and power wiring harness and snap the modules into the mounting plates Begin with Master module FIG 8 Snap Modules onto Rear Mounting Plates www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 10 of 18 1 6 Attach the power wiring harness to the modules which can effectively distribute power to nearby modules Attach the rest of the modules to the mounting plates Make sure that all modules are aligned at the same direction indicated by the arrow at the back of the module FIG 10 Snap Rest of the Modules onto Mounting Plates www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 11 of 18 3 SAFETY AND OPERATION 1 Caution Unplug the power supply from the mains power before connecting any cables as this can damage the products Caution Avoid looking directly into the LED l
5. ANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 of 18 1 2 Dimensions FIG 1 Mood Light Motion 297 mm 11 7 37 5mm 1 5 25 0mm va Mounting Standoff with through hole Support column Surface Carrier screw access 100mm 3 5 50mm 1 8 297 mm 11 7 100mm 3 5 100mm 3 5 q b e e 4 b v 9 9 v v po v 4 b www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 4of 18 1 1 3 Packing Contents FIG 2 Packing Contents RJ45 Jumper x 2 E 2 Cee sese Self m Tap Connector x 2 Jumper x 4 Plate Joiner x 4 www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 5 of 18 1 21 INSTALLATION 2 1 Poi
6. and system power supplies Please study this Installation Guide thoroughly and check the latest Technical Specification Sheets available from the Traxon website www traxontechnologies com before setup Any non compliance of the Installation Guide will void the Traxon warranty www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 12 of 18 4 SYSTEM CONFIGURATION FIG 11 System Diagram Daisy chaig up to 255 units Every module must be aligned A hs ME uA rd 7 i gt Faston terminal www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 13 of 18 FIG 12 System Diagram Connection 7 ie Faston terminal www traxontechnologie
7. hnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 8 of 18 1 2 Make sure the plates are attached square and level on the wall Lay out the design starting from upper left and move across to right and down FIG 5 Installation Direction 3 Prepare modules for installation For each panel configure one module to be Master module and the rest to be Slave module FIG 6 Interconnecting fixtures A a S 0 9 am o ae o o o www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 9 of 18 Attach the power wiring harness using cable ties There needs to be at least one connection within every group of 9 modules FIG 7 Cable Tie Mounting Position With the jumpers and surface material on the modules start
8. ight source at close range for your own safety Persons installing this products should make sure 1 The installation complies with all applicable codes state and local laws ordinances standards and safety regulations 2 The installation environment is carefully studied and suitable surge protection measure s is taken 3 He or she is qualified for the handling of electrical equipment Do not attempt to install or use the product until installation instructions and safety labels are fully understood This product is designed for indoor and outdoor use Ensure product operates within the specified temperature range Refer to 6 TECHNICAL SPECIFICATION for more details Do not attempt to open the product Not user serviceable Do not use the product if any part of it or the power cables are damaged Only use product for specified voltage do not exceed Refer to 6 TECHNICAL SPECIFICATION for more details Always maintain connection to ensure waterproofing If the product has been subjected to drastic temperature variances for example following transportation do not connect the fixture until it has reached room temperature as moisture condensation may cause electric shock and product damages When installing the products and system power supplies please ensure they will not be exposed to moisture and extreme heat and direct sunlight for outdoor products Besides keep a clean operating environment for the fixtures
9. nts To Consider Plan your installation before mounting any Mood Light Motions The following should be considered for a successful installation e This is a indoor product only do not install in outdoor environment Weather conditions and ambient temperature of installation site Installation distances and appropriate cable lengths Please consult your local Traxon office or authorized agent for necessary aid The number of Mood Light Motions and appropriate power sources e Proper surge protection 2 1 1 Installation Checklist 1 Prepare cables and all necessary accessories 2 Perform functional check of Mood Light Motions Take care not to damage cables connectors during pre installation checks 3 Ensure all pre installation checks laid out below have been followed Ensure all the Interconnection Cables Mood Light Motions and power Sources are stored in a dry area to guarantee the complete sealing of the System from water before and after installation www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 6 of 18 22 Pre Installation Checks 2 2 1 Cable Bending Cable must NOT be bent below the Minimum Bending Radius 4 x Cable
10. ontact your local Traxon office or distributor for details If the product is not working as specified please contact your nearest authorized service center or Traxon Technologies office for assistance www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 15 of 18 1 6 TECHNICAL SPECIFICATION Mood Light Motion Light Source 16 RGB LEDs Power Input 24V DC Power Consumption 5 5 Watts max per module Operating Temperature 309 to 50 C 22 F to 122 F startup temperature 20 C 4 F As with all electronic devices LED output degrades over time a term called lumen qepreciation This also explains why it is nearly impossible to expect photometric performances of two LED products with different service life spans to be the same The rate of LED degradation is a complex function of many factors such as operating efficiency quration of continuous operation and operating conditions e g ambient temperature Because LEDs are semiconductor devices their performances are subject to inherent variability commonly found in semiconductor industry To improve consistency in performance across the same product LED manufacturers sort LEDs into
11. re not overloaded due to an excess of products connected connected If problems persist or the product is not working as specified please contact your nearest authorized service center or Traxon Technologies office for assistance 8 WARRANTY STATEMENT Traxon Technologies warrants its Products against material or workmanship defects for a period of three 3 years from date of purchase provided that the purchased items are used under the conditions stated in this user manual Please refer www traxontechnologies com for all warranty terms and conditions www traxontechnologies com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 17 of 18 cra gt come cue AN OSRAM BUSINESS Please check for the latest updates and changes on the Traxon website 2015 TRAXON TECHNOLOGIES ALL RIGHT RESERVED Information is subject to change without prior notice www traxontechnologies com
12. s com 2015 TRAXON TECHNOLOGIES AN OSRAM BUSINESS ALL RIGHTS RESERVED TRAXON TX CONNECT ARE TRADEMARKS OF TRAXON TECHNOLOGIES U S PATENTS E U PATENTS JAPAN PATENTS OTHER PATENTS PENDING SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Installation Guide 10 15 V0 5 14 of 18 5 CARE AND MAINTENANCE Traxon products are of superior design and quality and should be treated with care The recommendations below will help fulfill anY warranty obligations and gain good use and longevity from the products Do not attempt or use the product s until you read and understand the installation instructions Failure to adhere to these instructions could result in serious injury or property damage Do not use product s if cables are damaged Do not connect cables and connectors when wet or in wet area Moisture on bare con nectors can cause electric shock and damage to product s Do not use product s in extreme heat environment Ensure there is sufficient airflow and use cool air circulation if required Do not drop knock or shake product s Rough handling can damage the electronics and void the warranty Do not use harsh chemicals cleaning solvents or strong detergents to clean products Wip e with a damp cloth on housings and a dry cloth on electronics to remove dirt or dust Do not attempt to service or repair the product s unless done by an authorized service personnel C
Download Pdf Manuals
Related Search