Home

FRPXIA3 User`s Manual

1. A Figure 4 FlashRunner FRPXIA3 front panel view Ke GE Li There are two LEDs for each programming channel e One LED for the Master Controller o Blinking during system initialization o ON after initialization e Engine status LED on the right refer to the FlashRunner Programmer s Manual chapter 11 2 e Programming status LED on the left multicolor LED BLUE RED GREEN FlashRunner FRPXIA3 User s Manual Table 1 Programming Status LED description Color Description OFF No programming has been performed yet BLUE FlashRunner is busy programming RED The previous programming has ended with errors GREEN The previous programming has been successful 1 3 2 ISP Connector The D SUB 50 pins male is the in system programming connector The pin out is available at the end of this manual 1 4 Programming Algorithms and Licenses FlashRunner FRPXIA3 includes programming algorithms for several devices In order to program a specific device however a specific license file for that device must be purchased Note FlashRunner FRPXIA3 comes already preinstalled with the license s you specified at the moment of purchase You can purchase additional licenses at any future moment Programming algorithms and license files are stored in the SD card see the FlashRunner Programmer s Manual for more information 1 4 1 Installing New Licenses When you buy
2. FlashRunner FRPXIA3 removing Power off and unplug the PXI CompactPCI chassis Untighten the screw on the front panel Push the ejector handle in the down position Slide out the module from the PXI CompactPCI chassis ON 2 2 1 Interfacing FlashRunner FRPXIA3 with your Test Programming Equipment One meter ISP cable is provided in the delivery package The cable is 1 side unterminated that allow you to interface with your test programming equipment Make all the required connections power oscillator ISP signals to the target microcontroller Typical connections for all the device families supported by FlashRunner are shown in the FlashRunner Programmer s Manual 2 3 Software Setup The FlashRunner FRPXIA3 system software setup installs all of the required components to your hard drive These components include e The FRPXIA3 Windows driver e The FlashRunner FRPXIA3 Control Panel Utility e Script examples e Interface Library DLL e Source code example in Visual C 2008 e FlashRunner FRPXIA3 Control Panel Utility source code in LabVIEW o Source code for LabVIEW 2013 o Source code for LabVIEW 2010 o Source code for LabVIEW 8 6 Documentations in PDF format 20 FlashRunner FRPXIA3 User s Manual Note to install the FlashRunner FRPXIA3 system software you must log in as Administrator Note to install the FlashRunner FRPXIA3 system software on Windows 8 and 8 1 machine see chapter 2 3 1 Inse
3. Digital input output 2 5 GND Ground 6 1DIO3 Isp channel 1 Digital input output 3 7 GND Ground 8 1DIO4 Isp channel 1 Digital input output 4 Connectors Pin Signal Name Description 9 GND Ground 10 1DIO5 Isp channel 1 Digital input output 5 11 GND Ground 12 1DIO6 Isp channel 1 Digital input output 6 13 GND Ground 14 1CLKOUT Isp channel 1 Clock output 15 GND Ground 16 1VPROGO Isp channel 1 Programmable voltage 0 17 1VPROG1 Isp channel 1 Programmable voltage 1 18 2DIO0 AO0 Isp channel 2 Digital input output 0 or analog output 0 19 2DIO1 A01 Isp channel 2 Digital input output 1 or analog output 1 20 GND Ground 21 2DIO2 Isp channel 2 Digital input output 2 22 GND Ground 23 2DIO3 Isp channel 2 Digital input output 3 24 GND Ground 25 2DIO4 Isp channel 2 Digital input output 4 26 2DIO5 Isp channel 2 Digital input output 5 27 GND Ground 28 2DIO6 Isp channel 2 Digital input output 6 29 GND Ground 30 2CLKOUT Isp channel 2 Clock output 31 GND Ground 32 2VPROGO Isp channel 2 Programmable voltage 0 33 2VPROG1 Isp channel 2 Programmable voltage 1 34 GND Ground 55 3DIO0 AO0 Isp channel 3 Digital input output 0 or analog output 0 36 3DIO1 AO1 Isp channel 3 Digital input output 1 or analog output 1 SI 3DIO2 Isp channel 3 Digital input output 2
4. Storage humidity 90 max without condensation 38
5. Vproco 3V lou 12mA Vou output high voltage on lines DIO CLKOUT Configured as digital lines 2 56V Vproco 3V lon 12mA Vor output low voltage on lines DIO CLKOUT Configured as digital lines 0 36V Vproco 5 5V lou 24mA Von output high voltage on lines DIO CLKOUT Configured as digital lines 4 86V Vproco 5 5V lon 24mA low Current source on lines DIO Configured as input with 3 4mA active pull ups DIO AO 1 0 voltage Configured as analog output OV 14 5V DIO AO 1 0 IO current sink and source Configured as analog output 40mA lon current source on lines DIO AO 1 0 Configured as analog lines 5 5mA with active pull ups VPROGO output voltage 1 6V 5 5V VPROGO current source 500mA VPROG1 output voltage 3 5V 13V VPROGI current source 250mA FlashRunner FRPXIA3 User s Manual 4 3 AC Characteristics Table 5 AC Characteristics Value Parameter Condition Min Typ Max Rise On lines DIO 6 2 Vproco 1 8V 40ns DIO 1 0 CLKOUT when Load 4700 100pF E configured as digital output Veroco 3 3V see figure 4 1a Sons push pull Vproco 5V 25ns a Far On lines DIO 6 2 Vproco 1 8V 35ns E DIO 1 0 CLKOUT when y Load 4700 100pF E configured as digital output Veroco 3 3V see figure 4 1a Lene push pull Vproco 5V 25ns Vproc1 3V 3 7us Rise On lin
6. 38 GND Ground 39 3DIO3 Isp channel 3 Digital input output 3 40 GND Ground 41 3DIO4 Isp channel 3 Digital input output 4 42 GND Ground 43 3DIO5 Isp channel 3 Digital input output 5 44 GND Ground 45 3DIO6 Isp channel 3 Digital input output 5 46 GND Ground 47 3CLKOUT Isp channel 3 Clock output 48 GND Ground 49 3VPROGO Isp channel 3 Programmable voltage 0 50 3VPROG1 Isp channel 3 Programmable voltage 1 FlashRunner FRPXIA3 User s Manual 4 Technical Specifications 4 1 Absolute Maximum Ratings Table 3 Absolute Maximum Ratings Parameter Value ISP Connectors Maximum input voltage on lines DIO AO 1 0 DIO 6 2 CLKOUT 1V to 7V Maximum current on lines DIO AO 1 0 DIO 6 2 CLKOUT 50mA Maximum current on line VPROGO 500mA Maximum current on line VPROG1 250mA 4 2 DC Characteristics and Functional Operating Range The CompactPCl interface is compliant with the PICMG 2 0 R3 0 Specifications PXI compatible 35 Technical Specifications Table 4 DC Characteristics and Functional Operating Range Value Parameter Condition Min Typ Max ISP Connectors Vi input low voltage on lines DIO Configured as digital lines 0 3Vproco Vin input high voltage on lines DIO Configured as digital lines 0 7Vproco VPROGO Vor output low voltage on lines DIO CLKOUT Configured as digital lines 0 36V
7. Specifications 38 FlashRunner FRPXIA3 User s Manual 0 Before Starting Note the FlashRunner System Software CD ROM and or SMH Technologies website www smh tech com may contain an updated version of this user s manual Please check before continuing reading this documentation 0 1 Important Notice to Users While every effort has been made to ensure the accuracy of all information in this document SMH Technologies assumes no liability to any party for any loss or damage caused by errors or omissions or by statements of any kind in this document its updates supplements or special editions whether such errors are omissions or statements resulting from negligence accidents or any other cause 0 2 Safety FlashRunner is a low voltage device However when integrating it inside an automatic test equipment or when interfacing it with other systems take all precautions in order to avoid electrical shocks due to for example different ground references Make all connections to the target system before applying power to the instrument To protect FlashRunner against electrostatic discharge ESD always connect yourself to ground e g via wrist straps when handling the instrument Always store FlashRunner inside an antistatic bag when not in use Before Starting 0 3 Getting Technical Support SMH Technologies is continuously working to improve FlashRunner firmware and to release programming algorithms f
8. BUS 4 SLOT 13 v Connect Disconnect Device connected Communication History MCSPING MCPONG gt MCSETENG ENG1 gt 1 RUN at25d frs 2 RUN script frs 3 RUN upd3371 frs Programming CH 1 script file CH1 at25d frs CH2 script file CH2 Iser J CH 3 script file CH3 upd3371 frs Q RUN PARALLEL Send Cmd Figure 14 User Application Example RUN PARALLEL We are now done with programming the target device Click the Disconnect button to free the pci resource 32 FlashRunner FRPXIA3 User s Manual 3 Connectors 3 1 Overview FlashRunner FRPXIA3 has 2 connectors e CompactPCI Type A Receptacle connector IEC 61076 4 101 e ISP connector D SUB 50 pins male 3 2 ISP Connectors The ISP connector contains the 3 ISP programming channels it has several input output lines both digital and analog that are automatically configured by FlashRunner depending on the specific target device to be programmed see the FlashRunner Programmer s Manual to learn how to connect these lines to your specific target device Note SP and I O signal are not optoisolated and are referenced to GND the power supply chassis ground Table 2 ISP Connector Signals Pin Signal Name Description 1 1DIO0 AO0 Isp channel 1 Digital input output 0 or analog output 0 2 1D101 A01 Isp channel 1 Digital input output 1 or analog output 1 3 GND Ground 4 1DIO2 Isp channel 1
9. PXIA3 User s Manual oose an option Continue 3 Exit and continue to Windows 8 Troubleshoot Refresh or reset your PC or use advanced tools Turn off your PC Figure 7 Windows 8 Advanced Startup Click on Advanced options to enter it Select Startup Setting Click Restart When the system restart Press 7 or F7 to choose Disable driver signature enforcement Startup Settings Press a number to choose from the options below sep Use number keys or functions keys FI FS 1 Enable debugging 2 Enable boot logging 3 Enable low resolution video 4 Enable Safe Mode 5 Enable Safe Mode with Networking 6 Enable Safe Mode with Command Prompt 7 Disable driver signature enforcement 8 Disable early launch anti malware protection 9 Disable automatic restart after failure Press F10 for more options Press Enter to return to your operating system Figure 8 Windows 8 Startup Settings 2 Open the CD ROM drive folder and double click on the setup file a Setup32 exe for 32bit Windows Operating System b Setup64 exe for 64bit Windows Operating System 3 Follow the on screen instruction until this window appear 23 System Setup You must restart your system for the configuration changes made to NI LabVIEW Run Time Engine 2013 SP1 f2 to take effect Click Yes to restart now or No if you plan to manually restart later Figure 9 Software Setup restart window 4 Click t
10. Step Tutorial Sending Commands to FlashRunner 24 Step by step tutorial user application example 30 Contents 3 Connectors 33 3 1 Overview 33 3 2 ISP Connectors 33 4 Technical Specifications 35 4 1 Absolute Maximum Ratings 35 4 2 DC Characteristics and Functional Operating Range 35 4 3 AC Characteristics 37 4 4 Physical and Environmental Specifications 38 FlashRunner FRPXIA3 User s Manual Index of Figures Figure 1 FlashRunner FRPXIA3 11 Figure 2 FlashRunner FRPXIA3 lateral view 14 Figure 3 FlashRunner FRPXIA3 schematic blocs 15 Figure 4 FlashRunner FRPXIA3 front panel view 16 Figure 5 Windows 8 charms bar 22 Figure 6 Windows 8 PC Settings 22 Figure 7 Windows 8 Advanced Startup 23 Figure 8 Windows 8 Startup Settings 23 Figure 9 Software Setup restart window 24 Figure 10 FlashRunner FRPXIA3 Control Panel 25 Figure 11 FlashRunner Control Panel Target Device Configured 27 Figure 12 FlashRunner FRPXIA3 Control Panel Binary File Conversion 28 Figure 13 FRPXIA3 Control Panel User Application Example 30 Figure 14 User Application Example RUN PARALLEL 32 Figure 15 Load Conditions 38 FlashRunner FRPXIA3 User s Manual Index of Tables Table 1 Programming Status LED description 17 Table 2 ISP Connector Signals 33 Table 3 Absolute Maximum Ratings 35 Table 4 DC Characteristics and Functional Operating Range 36 Table 5 AC Characteristics 37 Table 6 Physical and Environmental
11. an additional license for a specific device you will get An algorithm file alg A license file lic A device specific script example frs Overview The alg file contains the actual programming algorithm for the requested device and several other devices of the same family The lic file contains an unlocking code that will let you use the programming algorithm A license file enables the use of a specific programming algorithm on a specific FlashRunner instrument licenses are serial number specific The script file contains an example of script to use as a starting point for your specific programming needs for more information on scripts see the FlashRunner Programmer s Manual To install the new license do the following for each programming module 1 Copythe alg file into the ALGOS directory of the SD card if an alg file with the same name already exists overwrite it 2 Copythe lic file into the LICENSES directory of the SD card To copy files on the SD card use either a standard card reader connected to a PC or transfer the files using the FlashRunner FSSENDFILE command for more information on FlashRunner commands see the FlashRunner Programmer s Manual Alternatively you can use the FlashRunner FRPXIA3 Control Panel utility to install new programming algorithms and licenses For more information on the FlashRunner FRPXIA3 Control Panel please refer to the FlashRunner Programmer s M
12. anual 1 5 Upgrading the Firmware The FlashRunner engine firmware can be easily upgraded using the provided Control Panel utility For more information please refer to the FlashRunner Programmer s Manual FlashRunner FRPXIA3 User s Manual 2 System Setup 2 1 Overview Note the example shows how to set up the system for programming a Freescale MC68HC908QY4 microcontroller For how to connect to other target devices please refer to the FlashRunner Programmer s Manual This chapter will explain how to set up FlashRunner FRPXIAS3 for the first time The examples in this chapter will use the host system to send commands to FlashRunner When moving FlashRunner to the production environment you can take full advantage of the instrument s SD cards to make the instrument work without being controlled by the host system using script files For more information about the use of script files see the FlashRunner Programmer s Manual 2 2 Installing the module Please follow these steps for the FlashRunner FRPXIA3 installation 1 Poweroff and unplug the PXI CompactPCI chassis 2 Align the module s edge with the card guide in the PXI CompactPCI chassis 3 Slide the module into the chassis until the ejector handle locks in the up position 4 Tighten the screw on the front panel Power on the PXI CompactPCI chassis 6 Ifyou are using a Remote Controller you must restart the PC CA System Setup
13. ation Settings click the Scan FRPXIA3 devices button Follow the message box instruction and select the device in the scroll down menu Note if you have more than one FRPXIA3 installed in your chassis all devices will be showed on the Select Device scroll down menu 25 System Setup Select the device and click the Connect button On the Communication History section note the commands that have been sent and received In this case the MCSPING and MCSETENG ENG1 command are automatically sent to FlashRunner which replies with the PONG gt string and gt string The MCSETENG ENG1 instructs the instrument to send all subsequent command to the first programming module Send the following additional commands TCSETDEV FREESCALE MC68HC908QY4 HC08 TCSETPAR FOSC 16000000 TCSETPAR FDIV 4 TCSETPAR VDD 5000 These commands set respectively the target microcontroller the oscillator frequency the internal divisor and the VDD voltage In this example we used a 16 MHz oscillator the internal divisor for MC68HC908QY4 devices is fixed to 4 and the VDD is 5V FlashRunner will respond to each command with the gt string indicating that the command has been successfully executed After sending these commands the Control Panel will look like the figure below 26 FlashRunner FRPXIA3 User s Manual S sun Communication Setting Image file Create Flashrunner Bynary File rb S
14. be programmed to the target device not readable and not duplicable by non authorized people Log Files Erase blank check program read verify oscillator trimming etc FlashRunner s open architecture makes its firmware easily upgradeable to support both new devices and new features 1 2 Package Checklist The FlashRunner FRPXIA3 package includes the following items FlashRunner FRPXIA3 unit including SD cards already pre installed with the programming algorithm s you specified at the time of purchase One meter ISP cable 50 pins 1 side unterminated FlashRunner FRPXIA3 System Software CD ROM This User Manual A registration card Overview 1 3 Hardware Overview FRPXIA3 is composed of a PXI CompactPCI interface and 3 independent programming channels The Master Controller MC bridges the commands from the PCI bus to the three Programming Engines ia A TT IMM a LOL LLL Figure 2 FlashRunner FRPXIA3 lateral view The figure below shows you the schematic blocs of the FRPXIA3 module 14 FlashRunner FRPXIA3 User s Manual ET PXI CompactPCI BUS Master Controller N La l Engine 1 Engine 2 Engine 3 Figure 3 FlashRunner FRPXIA3 schematic blocs MC Master Controller ENG1 Programming Engine 1 ENG2 Programming Engine 2 ENG3 Programming Engine 3 Overview 1 3 1 Front Panel LEDs FR PXI A3 O MC O CHI O O HO O
15. button Follow the message box instruction and select the device in the scroll down menu chassis all devices will be showed on the Select Device scroll down menu Note if you have more than one FRPXIA3 installed in your 30 FlashRunner FRPXIA3 User s Manual Select the device and click the Connect button On the Communication History section note the commands that have been sent and received In this case the MCSPING and MCSETENG ENG1 command are automatically sent to FlashRunner which replies with the PONG gt string and gt string The MCSETENG ENG1 instructs the instrument to send all subsequent command to the first programming module In the text boxes CH1 CH2 CH3 you can write the script file to execute for each engine Click the RUN PARALLEL button to run the three scripts at the same time In the command history you can see RUN lt script name gt frs RUN lt script name gt frs RUN lt script name gt frs gt gt gt WN FP WD EB The application sends three commands lt Channel number gt RUN lt script name gt frs Then the application uses three times the GET_ANSWER function Interface Library See the FlashRunner Programmer s Manual for more information about the Interface Library functions Here below you can see an example 31 System Setup 7 SMH a Communication Setting Scan FRPXIA3 Devices Select Device FRPXIA3
16. end FlashRunner Binary File Scan FRPXIA3 Devices Select Device ENGINE 1 FRPXIA3 BUS 4 SLOT 13 Send Script Connect Disconnect Send Algorithm Device connected Send Licenses Update Firmware ENGINE 1 Get Log User Application Example Format SD Card Communication History TCSETDEV FREESCALE MC68HC908QY4 HC08 gt TCSETPAR FOSC 16000000 gt TCSETPAR FDIV 4 gt TCSETPAR VDD 5000 gt Send Cmd Figure 11 FlashRunner Control Panel Target Device Configured 5 When working with Freescale HC08 devices FlashRunner requires you to specify the power up and power down times in milliseconds Send the following two commands TCSETPAR PWDOWN 10 TCSETPAR PWUP 10 6 After specifying the target device settings we are ready to transfer to FlashRunner the binary image to be programmed into the target device FlashRunner accepts only image files in a frb FlashRunner Binary format To convert your binary Intel Hex or S19 image file to the FlashRunner format click the Create FlashRunner Binary Format button The following dialog box will appear 27 System Setup 7 Input OK Filename Cancel Format Offset He 0 Output will be created in the local BINARIES folder Filename frb Unused Bytes Dont t care 00h O FFh O User Show the FRB report after conversion Figure 12 FlashRunner FRPXIA3 Control Panel Binary File Conversion In the Inp
17. es One ground line common for all channels General features Fast programming algorithms developed to reach the memory technology speed limit of the target device PXI and CompactPCI chassis compatibility Supports most ISP protocols BDM JTAG SPI I2C MON ICC SCI etc Flexible fully configurable Compact and robust design for production environments Data integrity guaranteed every data transfer to from the host system or Secure Digital card is CRC tagged Safe and reliable projects and code images are stored on memory cards inside the board Hardware features CompactPCI 2 0 R3 0 compliant PXI fully compatible Integrated in only one slot of your PXI or CompactPCI chassis Support 3 3V and 5V PCI signal 33MHz PCI bus 3 true parallel in system programming channels For each channel e Five digital I O lines e Two digital I O or analog output lines e Two programmable voltages e One programmable clock output 512 bytes on board dynamic memory for each channel Standard off the shelf D SUB 50 pin ISP connector Programming status LED output for each channel BUSY PASS FAIL FlashRunner FRPXIA3 User s Manual 1 1 3 Software features Interface Library DLL to control the instrument from user written applications LabVIEW examples source code Control Panel Utility for fast and easy system setup ASCII Based commands Optional Data Protection System to make the contents of the binary file to
18. es DIO AO 1 0 VI 12V Load 4 7KQ 100pF a F configured as analog output __ PROG1 TC seefigure4 1a H Vprogi 14 5V 12us 7 Vproc1 3V z 8us FALL On lines DIO AO 1 0 RIONI 3 configured as analog output Vprogi 12V Load 100pF see figure 4 1b 20us Vproc1 14 5V 30us x Vproco 0 1 8V Load 150 10mF see figure 4 1a 10ms Rise On line VPROGO Vproco 0 3 3V Load 220 10mF see figure 4 1a 15ms 5 Vproco 0 5 5V Load 220 10mF see figure 4 1a 20ms Vproco 1 8 0V 300ms FALL On line VPROGO Vproco 3 3 0V Load 10mF see figure 41b 350ms T Vproco 5 5 0V 350ms 5 Verogi 0 3V Load 100 1mF see figure 4 1a 1 3ms Rise On line VPROG1 Verogi 0 5V Load 470 1mF see figure 4 1a 1 8ms a Vproc1 0 14 5V Load 940 1mF see figure 4 1a 13ms F Vproc1 3 0V 18ms fa FALL On line VPROG1 Verogi 5 0V Load 1mF see figure 4 1b 30ms Vproc1 14 5 0V 45ms CLKOUT frequency OMHz 50MHz 37 Technical Specifications Figure 15 Load Conditions 4 4 Physical and Environmental Specifications Table 6 Physical and Environmental Specifications Parameter Value Dimensions without front panel 160 x 100 mm Front panel dimension 128 x 20 mm ISP connectors type D SUB 50 pins male CompactPCI connector IEC 6107 4 101 Operating temperature 0 50 C Operating humidity 90 max without condensation Storage temperature 0 70 C
19. he No button 5 Then open another time the CD ROM drive folder and double click on the setup file 6 Follow the on screen instruction 2 4 Step by Step Tutorial Sending Commands to FlashRunner After setting up the hardware you are ready to send commands to the instrument The following steps will guide you through the process of launching your first FlashRunner commands using the provided FlashRunner FRPXIA3 Control Panel utility For detailed information about the FlashRunner FRPXIA3 Control Panel utility see the FlashRunner Programmer s Manual Note the following steps show how to program a Freescale MC68HC908QY4 microcontroller and the details are therefore specific for that microcontroller However the procedures shown are general and will allow you get a feel of how FlashRunner works 1 To launch the FRPXIA3 Control Panel utility select Start gt Programs gt SMH Technologies gt FRPXIA3 gt FRPXIA3 Control Panel The Control Panel utility will open 24 FlashRunner FRPXIA3 User s Manual 1E SIM smu Communication Setting Image file Create Flashrunner Bynary File frb Send FlashRunner Binary File Scan FRPXIA3 Devices Select Device Connect Jisconnect Device disconnected Update Firmware ENGINE 1 User Application Example Communication History Figure 10 FlashRunner FRPXIA3 Control Panel To establish a connection with FlashRunner on the Communic
20. ogramming the target device Click the Disconnect button to free pci resource For detailed information on all of the FlashRunner commands and their syntax including specific commands for specific family of microcontrollers please refer to the FlashRunner Programmer s Manual included in PDF format in the FlashRunner CD ROM Programming can be automated by creating scripts Scripts are text files stored in the SD cards which contain a sequence of FlashRunner commands See the FlashRunner Programmer s Manual for more information about scripts The FRPXIA3 Control Panel has a useful example of typical user application that implement the parallel programming using scripts See the FlashRunner Programmer s Manual for more information about scripts before continue to the next chapter 29 System Setup 2 5 Step by step tutorial user application example 1 To launch the FRPXIA3 Control Panel utility select Start gt Programs gt SMH Technologies gt FRPXIA3 gt FRPXIA3 Control Panel The Control Panel utility will open 2 Click the User Application Example button EEP smu Communica tion Setting Programmin 9 CH 1 script file Scan FRPXIA3 Devices CH1 CH 2 script file CH2 CH3 script file CH3 Figure 13 FRPXIA3 Control Panel User Application Example 3 To establish a connection with FlashRunner on the Communication Settings click the Scan FRPXIA3 devices
21. or new devices SMH Technologies offers a fast and knowledgeable technical support to all of its customers and is always available to solve specific problems or meet specific needs To get in touch with SMH Technologies please refer to the contact information below Phone 39 0434 421111 Fax 39 0434 639021 Technical Support support smh tech com 0 4 Additional Documentation This user s manual provides information about how to setup FlashRunner FRPXIA3 and its hardware characteristics For information about FlashRunner commands and their syntax including specific commands for specific family of microcontrollers please refer to the FlashRunner Programmer s Manual included in PDF format in the FlashRunner CD ROM FlashRunner FRPXIA3 User s Manual 1 Overview 1 1 What is FlashRunner FRPXIA3 FlashRunner FRPXIA3 is a universal high integrated in system gang programmer for PXI and CompactPCI systems FlashRunner FRPXIA3 is designed for programming multi PCB panel assemblies and it is based on FlashRunner technology the fast and reliable programming system for Flash based microcontroller and serial memories Figure 1 FlashRunner FRPXIA3 FRPXIA3 has 3 fully parallel and independent ISP In System Programming channels Each ISP channel is composed of e Five digital bi directional lines e Two analog digital lines analog out digital in out Overview One programmable clock output Two power lin
22. rt the System Software CD ROM into your computer s CD ROM Drive Open the CD ROM drive folder and double click on the setup file e Setup32 exe for 32bit Windows Operating System e Setup64 exe for 64bit Windows Operating System Then follow the on screen instructions FlashRunner FRPXIA3 system software is compatible with Windows XP 7 8 and 8 1 x32 and x64 system platform Windows 8 and 8 1 needs a particular installing procedure see the chapter here below 2 3 1 Windows 8 and 8 1 Software Setup Follow these steps 1 You have to disable the driver signature enforcement a Hover your mouse to the right hand bottom corner to display the Charms Bar then click on Settings b Select Change PC Settings 21 System Setup Gi 10 Unavailable 64 Unavailable 0 Notifications Power Keyboard Change PC settings Figure 5 Windows 8 charms bar c The PC Settings window will open Select General from the left hand menu Scroll the right target window to the bottom and select Restart now under Advanced Startup PC settings sia Activate Windows Personalize Available storage Users Notifications Search Share Privacy Remove everything and reinstall Windows Devices Ease of Access Windows Update Figure 6 Windows 8 PC Settings d When the PC restart select Troubleshoot from the Choose an option screen 22 FlashRunner FR
23. s the right to make improvements to FlashRunner its documentation and software routines without notice Information in this manual is intended to be accurate and reliable However SMH Technologies assumes no responsibility for its use nor for any infringements of rights of third parties which may result from its use SMH TECHNOLOGIES WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA PROFITS USE OF PRODUCTS OR INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF ADVISED OF THE POSSIBILITY THEREOF Trademarks SMH Technologies is the licensee of the SofTec Microsystems trademark All other product or service names are the property of their respective owners FlashRunner FRPXIA3 User s Manual Contents 0 Before Starting 9 0 1 0 2 0 3 0 4 Important Notice to Users 9 Safety 9 Getting Technical Support 10 Additional Documentation 10 1 Overview 11 1 1 1 2 1 3 1 4 1 5 What is FlashRunner FRPXIA3 11 1 1 1 General features 12 1 1 2 Hardware features 12 1 1 3 Software features 13 Package Checklist 13 Hardware Overview 14 1 3 1 Front Panel LEDs 16 1 3 2 ISP Connector 17 Programming Algorithms and Licenses 17 1 4 1 Installing New Licenses 17 Upgrading the Firmware 18 2 System Setup 19 2 1 2 2 2 3 2 4 2 5 Overview 19 Installing the module 19 2 2 1 Interfacing FlashRunner FRPXIA3 with your Test Programming Equipment 20 Software Setup 20 2 3 1 Windows 8 and 8 1 Software Setup 21 Step by
24. ty mA sm o Technologies UNIVERSAL PRODUCTION IN SYSTEM PROGRAMMING FlashRunner FRPXIA3 High Performance Gang In System Programmer PXI Module User s Manual Revision 1 0 June 2014 EN sm Technologies Copyright 2014 SMH Technologies DC10665 We want your feedback SMH Technologies is always on the lookout for new ways to improve its Products and Services For this reason feedback comments suggestions or criticisms however small are always welcome Our policy at SMH Technologies is to comply with all applicable worldwide safety and EMC EMI regulations Our products are certified to comply with the European New Approach Directives and the CE mark is applied on all our products This product as shipped from the factory has been verified to meet with requirements FCC as a CLASS A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate prevention measures Attaching additional wiring to this product or modifying the product operation from the factory default as shipped may effect its performance and cause interference with other apparatus in the immediate vicinity If such interference is detected suitable mitigating measures should be taken SMH Technologies E mail general information info smh tech com E mail technical support support smh tech com Web http www smh tech com Important SMH Technologies reserve
25. ut section specify the source file to be converted its format and the address from which the file conversion will start offset In the Output section specify the output filename and the value used to fill unused locations Click the OK button The FlashRunner Binary file will be created in the local BINARIES folder To transfer the created image to selected programming module click the button Send FlashRunner Binary File Select the file to begin the transfer The file will be saved on the SD card of the selected programming module in the BINARIES folder We are now ready to start the actual programming part Send the following commands TPSETSRC FILE DEMO FRB TPSTART TPCMD SETPWD CONST SFF SEF SEF SFF SFF SEF SEF FF TPCMD MASSERASE F TPCMD BLANKCHECK F EE00 4608 28 FlashRunner FRPXIA3 User s Manual TPCMD PROGRAM F EE00 EE00 4608 TPCMD VERIFY F S EE00 SEEOO 4608 TPEND The data to be programmed is taken from the image file starting at EE00 offset from the beginning of the file is programmed to the target microcontroller starting from the location EE00 and is 4608 bytes long The TPSETSRC command specifies the source file for the TPCMD PROGRAM e TPCMD VERIFY commands that come next All the actual programming operations are sent between a TPSTART and TPEND command The TPCMD SETPWD command sets the security bytes needed to perform subsequent operations 9 We are now done with pr

FRPXIA3 User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents