Rackmount Monitor User Manual
Contents
1. lt Part 1 gt 1 1 12 1 3 lt Part 2 gt 2 1 2 2 2 3 lt Part 3 gt 3 1 3 2 3 3 3 4 Contents RMD 151 F17 Package Content Structure Diagram amp Dimension Installation Specifications OSD Product Specifications On screen Display Operation OSD Picture In Picture PIP Picture By Picture PBP Options 3G HD SD SDI Broadcast grade input HDMI amp Audio F17 Touchscreen Resistive 48V 24V or 12VDC power UM CV 751 RMD F17 Q113V1 P 1 P 1 2 P 3 P4 5 P6 7 P 8 9 P 10 P 11 P 12 P 13 www rackmountsales com Before Installation E Itis very important to mount the equipment in a suitable cabinet or on a stable surface m Make sure the place has a good ventilation is out of direct sunlight away from sources of excessive dust dirt heat water moisture and vibration Unpacking The equipment comes with the standard parts shown in package content Check and make sure they are included and in good condition If anything is missing or damaged contact the supplier immediately How To Clean Your LCD Monitor A Caution m To avoid the risk of electric shock make sure your hands are dry before unplugging your monitor from or plugging your monitor into an electrical outlet m When you clean your monitor do not press down on the LCD screen Pressing down on the screen can scratch or damage your display Pressure damage is not covered under warranty m Use only2. Product Specifications RMD 151 F17 Connectivity When the audio output is connected speaker output is OFF 50 60Hz Safety Approval FCC amp CE Regulatory UM CV 751 RMD F17 Q113V1 P 4 www rackmountsales com Physical Product WxDxH 441 6 x 480 x 44 mm Packing WxDxH 590 x 687 x 120 mm a mamama O Applicable DVI D VGA Input PC Signal 1920 x 1080 x 60Hz Format 1280 x 1024 x 60 75Hz UM CV 751 RMD F17 Q113V1 P 5 www rackmountsales com lt 2 2 gt On screen Display Operation OSD RMD 151 F17 Membrane Switch Function 0 Turn the monitor on or off Display the OSD menu Da Act as an Enter key to select screen setting options Scroll through menu options and adjust the displayed control Go back to the previous on screen sub menu or main menu S Exit the OSD screen Remark All LED touch buttons in WHITE light The LED of Power touch button will flash continuously when there is no signal input O All the LED touch buttons will automatically turn off after 10 minutes of idle status except the Power O Light up all membrane buttons please press any button for 1 2 seconds except the Power G Picture Picture mode Standard Vivid Soft User mode to choose C i Picture gt MMM Brightness Adjust background black level of the screen image Brightness Contrast Adjust the difference between the image background Contrast black level and the foregro
3. CRYSTAL IMAGE dedicated KVM switch and rackmount screen technology User Manual 17 FHD 1080p LCD RMD 151 F17 1U LCD Drawer Options SDI HDMI Audio Touchscreen DC power 751 UM CV 751 RMD F17 Q113V1 www rackmountsales com Legal Information First English printing October 2002 Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice We are not liable for any injury or loss that results from the use of this equipment Safety Instructions Please read all of these instructions carefully before you use the device Save this manual for future reference E Unplug equipment before cleaning Don t use liquid or spray detergent use a moist cloth E Keep equipment away from excessive humidity and heat Preferably keep it in an air conditioned environment with temperatures not exceeding 40 Celsius 104 Fahrenheit m When installing place the equipment on a sturdy level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby m When the equipment is in an open position do not cover block or in any way obstruct the gap between it and the power supply Proper air convection is necessary to keep it from overheating E Arrange the equipment s power cord in such a way that others won t trip or fall over it
4. E If you are using a power cord that didn t ship with the equipment ensure that it is rated for the voltage and current labeled on the equipment s electrical ratings label The voltage rating on the cord should be higher than the one listed on the equipment s ratings label m Observe all precautions and warnings attached to the equipment E f you don t intend on using the equipment for a long time disconnect it from the power outlet to prevent being damaged by transient over voltage E Keep all liquids away from the equipment to minimize the risk of accidental spillage Liquid spilled on to the power supply or on other hardware may cause damage fire or electrical shock m Only qualified service personnel should open the chassis Opening it yourself could damage the equipment and invalidate its warranty E If any part of the equipment becomes damaged or stops functioning have it checked by qualified service personnel What the warranty does not cover E Any product on which the serial number has been defaced modified or removed E Damage deterioration or malfunction resulting from O Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by us Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as el
5. H Synchronized Video HD SDI 48kHz 16 20 24 bit 2 CH Synchronized Video SD SDI 48kHz 16 20 24 bit 2 CH Synchronized Asynchronized Video 3G SDI 150m at 2 97Gb s HD SDI 250m at 1 485Gb s SD SDI 480m at 270Mb s P 10 www es com lt 3 2 gt Options HDMI HDMI 1 1 CEA 861 D Audio 3 5mm audio jacks for audio in amp out and 2W 2W speakers dh For the above options casing depth will be extended from 480mm 18 9 to 530mm 20 9 UM CV 751 R F17 Q113V1 P 11 www es com lt 3 3 gt Options Touchscreen amp driver F17 USB Touchscreen Specification Model Activation Force lt 50g Stylus RO 8 Compatibility Windows 7 XP Vista Linux m USB touchscreen package includes 1 x 6ft USB cable quick reference guideline and CD disc Ml For detailed information please refer to the attached CD disc E As the touchscreen unit is not made of toughened glass please handle it carefully USB Touchscreen KKK For touchscreen option casing depth will be extended from 480mm 18 9 to 530mm 20 9 Please follow the below steps to setup the touch screen Step 1 Run the bundled CD disc Step 2 Double click the Setup exe Step 3 Follow the installation instruction to finish the setup Step 4 After installation run the TouchKit program amp the 4 point calibration Please do the initial calibration after the first setup Welcome to the Insta
6. cleansers made specifically for cleaning monitors and monitor screens Cleansers not made to clean monitors and monitor screens can scratch the LCD display or strip off the finish E Do not spray any kind of liquid directly onto the screen or case of your monitor Spraying liquids directly onto the screen or case can cause damage which is not covered under warranty m Do not use paper towels or abrasive pads to clean your monitor Using an abrasive pad or any wood based paper product such as paper towels can scratch your LCD screen Cleaning Your Monitor To clean your LCD safely please follow these steps Disconnect the power cord O Gently wipe the surface using a clean dry microfiber cloth Use as little pressure as possible Cleaning Tough Marks and Smudges To remove tough marks and smudges please follow these steps Disconnect the power cord O Spray a small amount of non abrasive cleanser on a microfiber cloth Caution Do not spray or apply any liquids directly onto the monitor Always apply the solution to your microfiber cloth first not directly on the parts you are cleaning Gently wipe the surface Use as little pressure as possible Wait until your monitor is completely dry before plugging it in and powering it up UM CV 751 RMD F17 Q113V1 www rackmountsales com lt Part 1 gt lt 1 1 gt Package Content RMD 151 F17 unit X 1 6ft VGA cable X 1 Power cord X 1 M6 screw cage nut amp cup
7. ectric power fluctuation or failure Use of supplies or parts not meeting our specifications Normal wear and tear Any other causes which does not relate to a product defect E Removal installation and set up service charges OOOOO00O Regulatory Notices Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Any changes or modifications made to this equipment may void the user s authority to operate this equipment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures E Re position or relocate the receiving antenna E Increase the separation between the equipment and receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected UM CV 751 RMD F17 Q113V1 www rackmountsales com
8. elect an input signal for PIP PBP Sub screen OSD Menu MISC PIP Source VGA S Video Composite DVI HDMI SDI YPbPr TV The PIP PBP is operable in the following table Sub Main VGA S Video Composite DVI HDMI SDI YPbPr TV UM CV 751 R F17 Q113V1 P 9 Www es com lt Part 3 gt lt 3 1 gt Options 3G HD SD SDI input Austin Hughes SDI input is an ideal solution for the broadcast grade video and high resolution CCTV market Designed for use with CyberView Full HD 1080p and ultra high resolution 1920 x 1200 LCD displays Austin Hughes provides a SDI input module without using additional space or power and it comes standard with a 2 year warranty SDI For SDI option casing depth will be extended from 480mm 18 9 to 530mm 20 9 INPUT Standard Compliance Compatible Video Format Compatible Audio Format Max Transmission Distance 75 ohm coaxial cable UM CV 751 R F17 Q113V1 3G SDI IN BNC x 1 0 8Vp p 75 ohm 3G SDI OUT BNC x 1 Active through equalized amp relocked Video SMPTE 425M 274M 296M 125M ITU R BT 656 SMPTE 299M 272M C 3G SDI 1080p 060 50Hz 4 2 2 1080p 30 25 24Hz 4 4 4 1080i 060 50Hz 4 4 4 720p 060 50Hz 4 4 4 HD SDI 1080p 30 25 24Hz 4 2 2 1080i 60 50Hz 4 2 2 720p 060 50Hz 4 2 2 SD SDI 480i 60HZ 4 2 2 ITU R BT 656 576i 50 zZ 4 2 2 3G SDI 48kHz 16 20 24 bit 2 C
9. llShield Wizard for TouchKit The InstallShield Wizard will install TouchKit on your computer To continue click Next UM CV 751 RMD F17 Q113V1 P 12 www rackmountsales com lt 3 4 gt Options DC Power o e ajo Input rating Input voltage 12 Volt 24 Volt 48 Volt Input range 9 18V 18 36V 36 75V Input current No load 50 mA 50 mA 50 mA Full load 4950 mA 2450 mA 1220 mA Output rating Output voltage 12 Volt 12 Volt 12 Volt Output current 4 16A 4 16A 4 16A Efficiency 84 85 85 x For DC power option 1 Option excludes 1 x power cord and 1 x AC power adapter 2 Casing depth will be extended from 480mm 18 9 to 530mm 20 9 UM CV 751 RMD F17 Q113V1 P 13 www rackmountsales com The company reserves the right to modify product specifications without prior notice and assumes no responsibility for any error which may appear in this publication UM CV 751 RMD F17 Q113V1 www rackmountsales com
10. nt back to factory setting Select for Help P 7 H positive V positive Volume Audio track Bass Treble Balance Analog TV audio Mute Sleep timer PIP mode PIP position PIP source System reset Information www rackmountsales com lt 2 3 gt How to Use Picture In Picture PIP Picture By Picture PBP RP F117 lt 2 3 1 gt Picture in Picture PIP Mode Display the Sub screen in the Main screen OSD Menu MISC PIP Mode Large Small OFF Main screen Sub screen Position Adjust the position of the Sub screen top left bottom left top right bottom right OSD Menu gt MISC PIP Position top left top right bottom left bottom right Ba top left top right bottom left bottom right Size Adjust the size of the Sub screen Large Small OSD Menu gt MISC PIP Mode Large Small Size of Sub screen LCD Monitor Large Sub screen Small Sub screen 1920 x 1200 552 x 414 480 x 360 1920 x 1080 552 x 414 480 x 360 1440 x 900 414 x 310 360 x 270 1366 x 768 392 x 294 340 x 254 1280 x 1024 368 x 276 320 x 240 UM CV 751 R F17 Q113V1 P 8 www es com lt 2 3 2 gt Picture By Picture PBP Mode Display the Sub screen next to the Main screen OSD Menu gt MISC PIP Mode PBP Main screen Sub screen Size LCD Monitor Main Sub screen lt 2 3 3 gt PIP PBP Source To s
11. und white level Hue Hue Adjust the screen hue value Saturation Saturation Adjust the saturation of the image color Picture size Picture size Adjust the image size Color temp Color temp Standard Cool Warm User to choose Noise reduce Noise reduce Reduce the noise of the image Sharpness Sharpness Adjust the image from weak to sharp UM CV 751 RMD F17 Q113V1 P 6 www rackmountsales com lt 2 2 gt On screen Display Operation OSD Pc Auto adjust Clock Phase H Position V Position Audio Audio mode Volume Bass Treble Balance Analog TV audio Mute 4 MISC Language Sleep timer PIP mode PIP position PIP source System reset Information UM CV 751 RMD F17 Q113V1 Automatically adjust sizes centers and fine tunes the video signal to eliminate waviness and distortion Adjust the clock value Adjust the phase value Align the screen image left or right Align the screen image up or down Movie Voice Normal Music mode to choose Adjust the volume of sound Set the value of bass sound Set the value of treble sound Set the balance value of treble and bass sound Set the value of analog TV audio sound Turn off the surrounding sound Select the language in which the OSD menu is displayed English Set the off time Adjust picture in picture setting Enter into PIP position Enter into the Sub source and sound source Return the adjustme
12. washer X 8 The above package content is only for the pure model VGA and DVI D only It varies with options such as SDI HDMI audio touchscreen amp DC power lt 1 2 gt Structure Diagram LCD panel LCD OSD membrane O Installation Slide Carry handle to release the 2 pt lock Audio speaker for HDMI or Audio option 2 point lock UM CV 751 RMD F17 Q113V1 P 1 www rackmountsales com lt 1 2 gt Dimension RMD 151 F17 Front View J at 7 19 Rackmount Side View UNIT mm 1mm 0 03937 inch 441 6 480 Product Dimension Packing Dimension W x D x H WxDxH RP F117 441 6 x 480 x 44 mm 590 x 687 x 120 mm 11 kg 15 kg 17 4 x 18 1 x 1 73 23 2 x 27 x 4 7 24 Ib 33 Ib The weight is only for the pure models It varies with accessories amp options such as SDI HDMI audio touchscreen amp DC power UM CV 751 RMD F17 Q113V1 P 2 www rackmountsales com lt 1 3 gt Installation How to install Installation Slides Step 1 E Insert the left and right rear mounting brackets into the display drawer Step E m Measure the depth of the front and rear mounting rails E Align each rear mounting bracket to a suitable length Step e Complete the installation E Fix the display drawer into the rack A M6 screw cage nut amp cup washer x 8 are provided UM CV 751 RMD F17 Q113V1 P 3 www rackmountsales com lt Part 2 gt lt 2 1 gt
Download Pdf Manuals
Related Search