UNO-3072A/3074A User Manual
Contents
1. 47 Chapter 3 7 Unscrew the two screws and take the PCI Anti vibration support kit from accessory box Ves f UNO 3072A 3074A User Manual 48 8 Insert the PCI Anti Vibration support kit through the hole shown till it insert tight Cut the overhang part and fasten screws 49 Chapter 3 3 5 Mounting UNO 3072A 3074A There are 3 types of mounting kits for UNO 3000 series Panel mount Stand mount Wallmount Please refer to the UNO 3000 Series Accessories Manual Note Due to thermal performance issues the Wall mount will only support specific models 3 6 Inst2. Inserting a CompactFlash Connecting Power Installing a Hard Disk Installing a PCI bus Card Mounting UNO 3072A 3074A Installing Power Cable BIOS Setup and System Assignments Rubber Foot Installation UNO 3072A 3074A User Manual viii 1 2 4 5 A 6 8 9 10 Appendix 1 System Settings and Pin Assignments 54 System I O Address and Interrupt Assignments 54 Table A 1 UNO 3072A 3074A System I O Port 54 Table A 2 UNO 3072A 3074A Interrupt Assignments 56 Board Connectors and Jumpers 57 Figure A 1 Backplane Connector amp Jumpers 57 Figure A 2 Mainboard Connector amp Jumpers Front 57 Table A 3 Connector and Jumper Descriptions 58 Table A 4 Connector and Jumper Descriptions 59 UNO 3072A 3074A Control Register 60 Table A 5 UNO 3072A 3074A Control Register 60 RS 232 Standard Serial Port COM3 COM4 Table A 6 RS 232 Serial Port Pin Assigns RS 232 422 485 Serial Port COM1 COM2 Table A 7 RS 232 422 485 Serial Port Pin Assigns 62 Eth
3. Data RS 485 Or 120 Ohm between RS 422 OFF Open Default 2 ON 120 Ohm between Rxt Rx RS 422 OFF Open Default 13 Chapter 2 2 2 6 RS 485 Auto Flow RS 422 Master Slave Selection UNO 3072A 3074A support Auto Flow Control mode of RS 485 in default without any setting or jumper required In RS 485 the driver automatically senses the direction of the data flow and switches the direc tion of transmission Then no handshaking is necessary UNO 3072A 3074A can also allow user to adjust Master Slave mode of RS 422 by changing setting in BIOS for each RS 422 485 port COMI amp 2 1 Boot up system or reset the system while boot up press Del to enter into BIOS 2 Select Integrated Peripherals Onboard Device COMI RS 422 or COM2 RS 422 3 The default of RS 422 is Slave User can change to Master for RS 422 Master Device requirement 4 F10 or Back to Save and Exit Setup to finish setup change In RS 422 if the device mode was set to Master the driver is always enabled and always in high or low status UNO 3072A 3074A User Manual 14 2 3 Optional RS 232 Interfaces COM3 COM4 UNO 3072A 3074Aoffers two optional RS 232 serial communication interfaces COM3 and COM4 Please refer to Appendix A 4 for their pin assignments The default of these two ports is Disabled In order to use these two COM potts fo
4. Interrupt Triggering Edge Control Status Register DMTE DIOTE 207H Interrupt Flag Clear Register CTR1F CTROF DI1F DIOF 208H R W 82654 Chip Counter0 Register 209H R W 82654 Chip Counter1 Register 20BH R W 82654 Chip Control Register 20CH R W CounterO Start Control Output Status Register CTRO CTRO Out Gate 20DH R W Counter Start Control Output Status Register CTR1 CTR1 Out Gate 20EH R W Setting Register CTRO CTRO CTRO CTRO IntSet OutSet GateSet CLKSet 20FH R W Counter1 Setting Register CTR S1 0 CTR1 CTR1 CTR1 CTR1 32Set IntSet OutSet GateSet CLKSet 210H R W DIAG LED Control Register LEDS1 LEDSO LEDEn Refer to 82c54 manual UNO 3072A 3074A User Manual 60 4 RS 232 Standard Serial Port COM3 COM4 12345 OO0OO0O00 OOOO 6789 Table A 6 RS 232 Serial Port Pin Assigns Pin RS 232 Signal Name DCD RxD TxD DTR GND DSR RTS CTS O A WwW NM gt RI 61 Appendix 5 RS 232 422 485 Serial Port COM1 COM2 12345 OOOOO OOOO 6789 Table A 7 RS 232 422 485 Serial Port Pin Assigns Pin RS 232 RS 422 RS 485 1 DCD Tx DATA 2 RxD Tx DATA 3 TxD Rx NC 4 DTR Rx NC 5 GND GND GND 6 DSR NC NC 7 RTS NC NC 8 CT
5. UNO 3072A 3074A Intel Dual Core Atom Embedded Automation Computer with Two Four PCI Slot Extensions User Manual Copyright Notice The documentation and the software included with this product are copy righted 2011 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this man ual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided this manual 1 intended to be accurate and reli able However Advantech Co Ltd assumes no responsibility for its use nor for any infringements of the rights of third parties which may result from its use Acknowledgements IBM PC AT PS 2 and VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp amp 15 a trademark of Chips and Technologies Inc All other product names or trademarks are properties of their respective owners Part No 2003307420 Ist Edition Printed in Taiwan May 2011 UNO 3072A 3074A User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its prod ucts will be free from defects in materials and workmanship for two years
6. UNO 3072A 3074A User Manual 28 2 7 10 Cascaded 32 bit Counter You can also cascade counter 0 and counter 1 together as one 32 bit coun ter timer and it s configured by control bit CTR32Set Table 2 14 32 bit Counter Control Bit 0 Disable Default 1 Cascade counter 0 and counter 1 into one 32 bit counter Note UNO 3072A 3074A provides built in examples to show how to deliver counter functionality Refer to console mode examples in C Program Files Advan tech UNO UNO_IsaD O Examples Console Install DI O driver from the UNO CD to use these examples 2 8 Power Inputs UNO 3072A 3074A comes with a Phoenix connector that carries 9 36 Vpc external power input and features reversed wiring protection Therefore it will not cause any damage to the system by reversed wiring of ground line and power line Please refer to Figure 2 11 for location of power input ELLE r 1 Figure 2 11 Figure Location of Power and grounding eSATA 29 Chapter 2 2 8 1 LED and Buzzer for System Diagnosis In a headless application an application without a monitor display it is always difficult to know the system status Another PC may be needed to monitor a headless device s status via RS 232 or Ethernet In order to solve this problem UNO 3072A 3074A offers a solution which can turn the four LED originally used for COM port Tx
7. from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous test ing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available 3 Ifyour product is diagnosed as defective obtain RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order
8. 2 6 Onboard Isolated Digital Output The UNO 3072 A 3074A has 4 isolated DO channels designated DOO DO3 2 6 1 Pin Assignments The connector type of UNO 3072A 3074A is plug in screw terminal block that enables you to connect to field I O devices directly without additional accessories Figure 2 9 and Table 2 17 show its pin assignment as well as signal description DIO 2 3 DI CO Figure 2 6 Digital Output Connector Pin Assignments Table 2 6 Digital Output Connector Signals Signal Name Reference Direction Description DO lt 0 7 gt GND Output Isolated DO signals O GND DO isolated ground COM DO_COM as using inductance load 21 Chapter 2 2 6 2 Power On Configuration Default configuration after power on or hardware reset is to set all the iso lated digital output channels to open status the current of the load can t be sink so that users need not worry about damaging external devices during system startup or reset When the system is hot reset then the status of iso lated digital output channels are selected by jumper CN27 Table 2 18 shows the configuration of jumper CN27 CN27 Power on configuration after hot reset 1 2 3 Reset all digital output 1 2 3 Keep last status after hot reset UNO 3072A 3074A User Manual 22 2 6 3 Isolated Outputs Each of isolated output channels comes equipped with a
9. CN15 Wet Contact Selection Jumper CN5 Hardware AT selection Jumper CN7 PCI frequency Selection closed 66MHz CN13 3P Fan Power On Closed Always On CN11 CN12 SATA power connector CN18 Audio Out Connector CN20 4P External Power connector P1PCI 2 PCI slot 2 P1PCI 3 PCI slot 3 UNO 3072A 3074A User Manual 58 Table A 4 Connector and Jumper Descriptions Location Label Function Main CN7 Internal USB board CN9 CN12 Gigabit LAN USB Connector CN14 SATA Connector CN16 CN17 Optional Cable Wired COM3 COM4 pin header CN18 CN19 Optional Cable Wired PS 2 pin header CN20 Clear CMOS CN21 Print Port Pin header CN22 LVDS LVDS power Reserved CN23 CN24 CF1 CF2 CN25 CN27 DO status after reset Jumper CN28 COM port RS 232 RS 4228485 selection CN29 CN30 COM1 COM2 DB 9 connector CN33 3P Fan power connector CN39 Video detect Jumper for Dual DVI D selection Close Disable VGA CN41 Optional Cable Wired USB pin header SW3 CF1 CF2 Master selection SW6 Reserved 59 Appendix A UNO 3072A 3074A Control Register Table A 5 UNO 3072A 3074A Control Register Base 7 6 5 4 3 2 1 0 Address 200H R Isolated Digital Input Status Register DI7 DI6 DI5 014 013 012 DIO 201H R W_ lsolated Digital Output Control Status Register 006 005 004 002 001 000 202H Interrupt Enable Control Status Register DIEN DIOEN 203H
10. Card and a photocopy proof of purchase date such as your sales receipt in a shippable container product returned without proof of the purchase date is not eligible for war ranty service 5 Write the number visibly on the outside of the package and ship it prepaid to your dealer iii This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech FCC Class A This equipment has been tested and found to comply with the limits for a Class digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manual may cause harmful interference to radio communications Operation of this equipment in a residential area 15 likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance Step 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product Step 2 Contact your distributor or Advantech s customer service center if you need additional assistance Have the fol
11. Darlington tran sistor All output channels share common emitters Please note that if an external voltage 5 40 Vpc 1 applied to iso lated output channel while it is being used as an output channel the cur rent will flow from the external voltage source to the UNO 3072A 3074A Please take care that the current through each DO pin not exceed 200 mA Figure below shows how to connect an external output load to the UNO 3072 3074 isolated outputs Please note that DO2 and may be configured as output pins of Counter 0 and Counter 1 Internel Externel DOO 7 LoadO 7 When you use inductance load please refer below figure Internel Externel DO COM Load0 7 Note UNO 3072A 3074A provides built in examples to show how to deliver digital output functionality Refer to con sole mode examples in C Program Files Advantech UNO UNO_IsaDIO Exam ples Console Please install DI O driver from the UNO CD to use these examples 23 Chapter 2 2 7 Isolated Counter Timer The UNO 3072A 3074A uses one 82C54 programmable timer counter chip that includes three independent 16 bit down counters counter 0 counter 1 and counter 2 Counter 0 and counter 1 are for users and counter 2 is specified for the system and can t be used by user Each counter has clock input gate input and pulse output They can be programmed to count from 2 up to 65535 or cascaded into one 32 bit counter The UNO 3
12. amp Rx to programmable LED indicators while They can be programmed to show a systems status by LED indicator PER m SR L t 1 RX2 I Ul LEDI LED2 LED3 LED4 aN gt Figure 2 12 Programmable LED In order to use programmable LED user needs to change BIOS setting to switch the LED for COM port Tx amp Rx to programmable LED function Please follow the steps below I Boot up or reset the system press Del to enter into BIOS 2 Select Integrated Peripherals Onboard Device LED Select Default setting is Comport TX RX change the setting to Pro grammable LED 3 Press F10 or Back to Save and Exit Setup to finish setup change Table 2 15 LED Control Register 212H RW Diagnostic Programmable LED Register x x X X 1 2 4 Note 0 DIAG LED disable 1 DIAG LED enable UNO 3072A 3074A User Manual 30 2 9 USB Connector The USB connector is used for connecting any device that conforms to the USB interface Many recent digital devices conform to this standard The USB interface supports Plug and Play which enables you to connect or disconnect a device whenever you want without turning off the computer The UNO 3072A 3074A provides four connectors of USB interfaces The USB interface complies with USB UHCI Rev 2 0 compliant The USB interface can be disable
13. interrupt flag bit CTROGate CTR1Gate Counter 0 1 gate control bit CTROOut CTR1Out Counter 0 1 output status bit CTROCLKSet CTRICLKSet Counter 0 1 clock source control bit CTROGateSet CTR1GateSet Counter 0 1 gate source control bit CTROOutSet CTR10utSet Counter 0 1 output destination control bit CTROIntSet CTR1IntSet Counter 0 1 interrupt control bit S0 S1 Counter 0 1 internal clock control bit CTR32Set Cascaded 32 bit counter control bit 25 Chapter 2 2 7 2 Counter 0 Function Block DIO CTROGate DH 4 CTR0GateSet Counter 0 CTROOutSet CTROIntSet Interrapt Circuit pog Figure 2 8 Counter 0 Function Block 2 7 3 Counter 1 Function Block DI2 CTR1Gate 5150 CTR1GateSet CTRiGueSn 4 CTR1CLKSet y Gate Counter 1 Out CTR10utSet CTRiOuS 006 gt Diable CTR1IntSet Interrupt Circult 002 CTROOUT r 003 t CTR10UT CTRA Det Dable Interrapt CTRIF CIRiDuCet 1 Enable Interrupt M Figure 2 9 Counter 1 Function Block 2 7 4 32 bit Counter Function Block CTR32Set 1 CTR1GateSet e CTR AGateS et Gate CTR1CLKSet Cascaded 32 bit Counter CTRICLKSete B CTRICL 5 0 012 CTRiGate 013 TOOKHZ 10KHZ KHZ 100Hz
14. is on 2 Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components UNO 3072A 3074A User Manual vi Chapter Chapter NNN 2 6 Contents OVERVIOW ecce RU Introduction Hardware Specifications Safety Precautions Chassis Dimensions Figure 1 1 Chassis Dimensions Packing shasqa Hardware Functionality 10 Introduction Figure 2 1 Front Panel of UNO UNO 3072A 3074A 10 RS 232 422 485 Interface COM1 COM2 11 2 2 1 16C950 UARTs with 128 byte FIFO 11 2 2 2 RS 422 485 Jumperless Detection 11 2 23 Automatic Data Flow Control Function for RS 485 11 2 2 4 RS 232 422 485 Selection sse Figure 2 2 RS 422 485 Jumper Setting Figure 2 3 RS 232 Jumper Setting 2 25 Terminal Resistor Setup for RS 422 485 Table 2 1 Terminal Resistor Settings 2s 2 2 6 RS 485 Auto Flow RS 422 Master Slave Selection 14 Optional RS 232 Interfaces COM3 COMA 15 LAN Ethernet Connector Onboard Isolated Digital Input 2 5 1 Pin Assignments ga Figure 2 4 Digital Input Connector Pin Assign
15. jumper 1 2 3 Turn on the system The CMOS is now cleared 4 Turn on the system The BIOS is reset to its default setting Table A 13 CN3 Clear CMOS Configuration Function Clear CMOS 1 2 1 2 Normal Default UNO 3072A 3074A User Manual 66 A 12 External amp Internal Connectors Table A 14 External SATA connector pin assignment Pin Signal name GND TX TX GND RX RX N Q BY Q N gt GND 67 Appendix Table 15 Internal SATA DATA Connectors CN40 Pin Signal name GND TXt TX GND RX RXt NI co N gt GND UNO 3072A 3074A User Manual 68 Table A 16 Internal SATA Power Connectors CN41 Pin Signal name GND GND 12V 12V 5V 5V 3V OW A O 3V 69 Appendix A UNO 3072A 3074A User Manual 70 APPENDIX Programming the Watchdog Timer Appendix Programming Watchdog Timer B 1 Below is a sample of programming code for controlling the Watchdog Timer function MOV DX 4EH MOV AL 87H OUT DX AL OUT DX AL MOV DX 4EH AL 2BH OUT DX AL MOV DX 4FH IN AL DX AND AL OEFH Setbit 4 0 Pin 89 WDTO OUT DX AL MOV DX 4EH MOV AL 07H point to Logical Device Number Reg OUT DX AL MOV DX 4FH MOV AL 0
16. the UNO 3072A 3074A When the interrupt request signals occur then the software will service these inter rupt requests by ISR Interrupt Service Routine The multiple interrupt sources provide the card with more capability and flexibility 2 5 4 IRQ Level The IRQ level is by default set by the system BIOS IRQ 7 is reserved for DI interrupt and counter interrupt UNO 3072A 3074A User Manual 18 2 5 5 Interrupt Control Register Table 2 2 Interrupt Control Register Bit Map Base Address 7 6 5 4 3 2 1 0 202H RW Interrupt Enable Control Status Register DI1EN DIOEN 203H R W Interrupt Triggering Edge Control Status Register DI1TE DIOTE 207H R W Interrupt Flag Clear Register DI1F DIOF The Interrupt Control Register controls the function and status of each interrupt signal source Table 2 13 shows the bit map ofthe Interrupt Con trol Register The register is readable writeable register While being writ ten it is used as a control register and while being read it is used as a sta tus register DIOEN amp DIIEN DIO amp DII Interrupt disable enable control bit DIOTE amp DIITE DIO amp DII Interrupt triggering edge control bit DIOF amp DIIF DIO amp interrupt flag bit 2 5 6 Interrupt Enable Control Function Table 2 3 Interrupt Disable Enable Control DIOEN amp DI1EN Interrupt Disable Enable Control 0 Disable 1 Enable T
17. 072A 3074A has two isolated counter input channels desig nated and DI3 with two isolated output channels designated DO2 and DO3 Therefore you can set each counter of 82C54 as counter function or timer function 2 7 1 Counter Timer Control Register The Counter Timer Control Register controls the function and status of each counter timer signal source Table 2 19 shows the bit map of the Counter Timer Control Register The register is readable writable register While being written it is used as a control register and while being read it is used as a status register Table 2 8 Counter Timer Control Register Bit Map Base 7 6 5 4 3 2 1 0 Address 207H R W Interrupt Flag Clear Register CTR1F CTROF 208H R W 82C54 Chip Counter0 Register 209H R W 82C54 Chip Counter1 Register 20BH R W 82C54 Chip Control Register 20CH CounterO Start Control Output Status Register CTRO CTRO Out Gate 20DH R W Counter1 Start Control Output Status Register CTR1 CTR1 Out Gate 20EH RW CounterO Setting Register CTRO CTRO CTRO CTRO IntSet OutSet GateSet CLKSet UNO 3072A 3074A User Manual 24 Table 2 8 Counter Timer Control Register Bit 20FH R W Counter1 Setting Register CTR32 1 0 CTR1 CTR1 CTR1 CTR1 Set IntSet OutSet GateSet CLKSet CTROF CTRIF Counter 0 1
18. 2 8 Counter 0 Function Block 2 7 3 Counter 1 Function Block Figure 2 9 Counter 1 Function Block 27 4 32 bit Counter Function Block CTR32Set 1 26 Figure 2 10 32 bit Counter Function Block 2 7 5 Counter Clock Source see Table 2 9 Counter Clock Source Control Bit Es 2 7 6 Counter Internal Clock e Table 2 10 Counter Internal Clock Control Bit 27 2 7 7 Counter Gate Source dd i Table 2 11 Counter Gate Source Control Bit S 2 7 8 Counter Output Destination see Table 2 12 Counter Output Destination Control Bit 28 2 7 9 Counter Interrupt Flag sese Table 2 13 Counter Interrupt Flag Control Bit 2 7 10 Cascaded 32 bit Counter Table 2 14 32 bit Counter Control Bit POWER Figure 2 11 Figure Location of Power grounding 29 2 8 1 LED and Buzzer for System Diagnosis 30 Figure 2 12 Programmable LED Table 2 15 LED Control Register USB Connector uctor trece pertenece Battery Backup Figure 2 13 LED Location for Battery Backup 31 2 10 1 Lithium Battery Specification Figure 2 14 Lithium Battery for SRAM IEEET1394 iei trece nete tepidis SATA Hard Drive RAID Suppott Initial Setup
19. 5150 CTR10utSet CTR10uSe 4 006 0 TRA Out Diable I CTR10UT CTR1IntSet CRIOU Disb Interrupt Interrupt Circult P mem CTRIF Figure 2 10 32 bit Counter Function Block UNO 3072A 3074A User Manual 26 2 7 5 Counter Clock Source There are two clock sources available for the user counters by setting counter clock control bits CTROCLKSet and CTR1CLKSet Table 2 9 Counter Clock Source Control Bit CTROCLKSet 0 Internal clock default 1 External clock from digital input 1 DI1 channel CTR1CLKSet 0 Internal clock default 1 External clock from digital input 3 DI3 channel 2 7 6 Counter Internal Clock There are four frequency options to choose according to applications and it s set by internal clock control bits SO and S1 Table 2 10 Counter Internal Clock Control Bit 1 0 Time 0 0 100 KHz default 0 1 10 KHz 1 0 1 KHz 1 1 100 Hz 27 Chapter 2 2 7 7 Counter Gate Source The gate sources you select determine what kind of gate input signal to enable your counter timer when receiving clock input There are two gate sources available for the user counters by setting gate source control bits CTR0GateSet and CTR1GateSet Table 2 11 Counter Gate Source Control Bit CTROGateSet 0 Gate source from CTROGate control bit Default 1 Gate source from digital input 0 DIO channel CTR1Gat
20. 74A Modern electronic devices are very sensitive to static electric charges Use a grounding wrist strap at all times Place all electronic components on a static dissipative surface or in a static shielded bag If DC voltage is supplied by an external circuit please put a protection device in the power supply input port 5 Chapter 1 1 4 Chassis Dimensions Figure 1 1 Chassis Dimensions UNO 3072A 3074AUser Manual 6 1 5 Packing List The accessory package of UNO 3072A 3074A contains the following items A SATA signal cable and power cable B Keyboard Mouse PS 2 cable C Warranty card D Driver and Utility CD ROM E 4 x anti vibration rubber F Mini Jumper G Paper menu H Power connector 1 Digital Input and Digital Output Phoenix Connector J Key Pro Bracket 7 Chapter 1 UNO 3072A 3074AUser Manual Hardware Functionality This chapter shows how to setup the UNO 3072A 3074A hardware func tions including connecting peripherals and setting switches and indicators Sections include Introduction RS 232 Interface RS 232 422 485 Interface LAN Ethernet Connector DI O and Counter Power Connector LED and Buzzer PS 2 Mouse and Keyboard Connector USB Connector VGA Display Connector Battery Backup SRAM Reset Button Chapter 2 Hardware Functionality 2 1 Introduction The two figures below show the connectors on UN
21. 8H select logical device 8 OUT DX AL MOV DX 4EH MOV AL 30H Set watch dog activate or inactivate UNO 3072A 3074A User Manual 72 43 Appendix DX 4FH MOV 01 01 activate 00 inactivate OUT DX AL MOV DX 4EH MOV AL F5H Setting counter unit is second OUT DX AL MOV DX 4FH MOV AL 00H OUT DX AL MOV DX 4EH MOV AL F6H OUT DX AL MOV DX 4FH MOV AL 05H Set 5 seconds OUT DX AL MOV 4 MOV AL AAH OUT DX AL 73 Appendix B UNO 3072A 3074A User Manual 74
22. Family 03C0 03DF Mobile Intel 965 Express Chipset Family 03F6 03F6 Primary IDE Channe 03E8 03EF Communications Port COM3 03F8 03FF Communications Port COM1 0500 051F Intel ICH8 Family SMBus Controller 283E 0778 077 Printer Port LPT1 0D00 FFFF PCI bus F200 F20F Intel ICH8M 3 port Serial ATA Storage Controller 2828 F300 F30F Intel ICH8M 3 port Serial ATA Storage Controller 2828 F400 F403 Intel ICH8M 3 port Serial ATA Storage Controller 2828 F500 F507 Intel ICH8M 3 port Serial ATA Storage Controller 2828 F600 F603 Intel ICH8M 3 port Serial ATA Storage Controller 2828 F700 707 Intel ICH8M 3 port Serial Storage Controller 2828 F800 F80F Intel ICH8M Ultra ATA Storage Controllers 2850 F900 F91F Intel ICH8 Family USB Universal Host Controller 2832 FA00 FA1F Intel ICH8 Family USB Universal Host Controller 2831 FB00 FB1F Intel ICH8 Family USB Universal Host Controller 2830 FC00 FC1F Intel ICH8 Family USB Universal Host Controller 2835 FD00 FD1F Intel ICH8 Family USB Universal Host Controller 2834 FF00 FF07 Mobile Intel 965 Express Chipset Family 443 Watchdog timer DC000 DFFFF Battery backup resource Appendix A Table 2 UNO 3072A 3074A Interrupt Assignments Interrupt Number Interrupt source NMI Parity error detected IRQ 0 System timer IRQ 1 Standard 101 102 Key or
23. Microsoft Natural PS 2 Key board IRQ 2 Interrupt from controller 2 cascade IRQ 3 Communications Port COM2 IRQ 4 Communications Port COM1 IRQ 5 Communications Port COM4 IRQ 6 Standard floppy disk controller IRQ 7 DIO IRQ 8 System CMOS real time clock IRQ 9 Microsoft ACPI Compliant System IRQ 10 Communications Port COM3 IRQ 11 Reserved for watchdog timer IRQ 12 PS 2 Compatible Mouse IRQ 13 Numeric data processor IRQ 14 Primary IDE Channel IRQ 15 Intel ICH8 Family SMBus Controller 283E IRQ 16 Mobile Intel 965 Express Chipset Family UNO 3072A 3074A User Manual 56 A 2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO 3072A 3074A board The following sections tell you how to configure the UNO 3072A 3074A hardware setting Figures 1 to A 5 show the location of the con nectors and jumpers CN4 Dry Contact lt CN15 Wet Contact ES EE Ratt m dl e e e o L Figure A 2 Mainboard Connector amp Jumpers Front 37 Appendix Table A 3 Connector and Jumper Descriptions Location Label Function Backplane FS1 FS2 Fuse for input DC power CN4 Dry Contact Selection Jumper
24. O 3072A 3074A and following sections give you detailed information about function of each peripheral Figure 2 1 Front Panel of UNO 3072A 3074A UNO 3072A 3074A User Manual 10 2 2 RS 232 422 485 Interface COM1 COM2 The UNO 3072A 3074A offers two industrial RS 232 422 485 serial communication interface ports COM1 and COM2 Please refer to Appendix A S for their pin assignments The default setting of COMI and COM2 are RS 422 485 Please refer to section 2 2 4 for how to deter mine RS 232 or RS 422 485 2 2 1 16C950 UARTs with 128 byte FIFO Advantech UNO 3072A 3074A comes standard with Oxford OXuPC1952 UART two OX16C950 UARTS fully software compatible with 16C550 which containing 128 bytes FIFOs These upgraded FIFOs greatly reduce CPU overhead and are an ideal choice for heavy multitask ing environments 2 2 2 RS 422 485 Jumperless Detection In RS 422 485 mode UNO 3072A 3074A automatically detects signals to match RS 422 or RS 485 networks Refer to section 2 2 5 2 2 3 Automatic Data Flow Control Function for RS 485 In RS 485 mode UNO 3072A 3074A automatically detects the direction of incoming data and switches its transmission direction accordingly So no handshaking signal e g RTS signal is necessary This lets you easily build an RS 485 network with Datat Data and Ground More impor tantly application software previously written for full duplex RS 232 environments can be maintained witho
25. RAM It also support two HDD bays with RAID 0 1 The design with an open platform can fulfill demanding requirements from the industrial field especially for machine vision or motion controllers 1 2 Hardware Specifications CPU Intel Dual Core Atom Processor D510 1M L2 Cache 1 66GHz System Memory Built in 2GB DDR2 RAM 2 x 200 pin SODIMM sockets Battery Backup RAM 512 KB Chipset Intel Atom D510 Intel 82801HEM I O Controller Hub ICH8EM BIOS AMI 4 Mbit Flash BIOS supports Boot on LAN function Display DB15 VGA connector 1600 x 1200 85 Hz Audio Line Out Clock Battery backup RTC for time and date Serial Ports 2 x RS 232 422 485 with DB 9 connector and Automatic RS 485 data flow control RS 232 Speed 50 bps 115 2 kbps RS 422 485 Speed 300 bps 921 6 kbps Optional cable Serial Ports 2xRS 232 50 115 2kbps LAN Two Intel 82574L 10 100 1000 Base T RJ 45 ports with wake on LAN and teaming function support UNO 3072A 3074A User Manual 2 USB Interface External Four USB ports USB EHCI Rev 2 0 compliant Internal One USB port USB EHCI Rev 2 0 compliant Optional cable wiring 2 x USB ports USB EHCI Rev 2 0 compliant IEEE 1394 Interface 2 x IEEE 1394 type B with Bilingual connectors Compact Flash Slots Two type CompactFlash Slots One internal and one external HDD SATA HDD extension kit for two standard 2 5 HDDs RAID 0 1 function support One external eSATA device Does not support
26. S NC NC 9 RI NC NC A 6 Ethernet RJ 45 Connector LAN1 LAN2 Table A 8 Ethernet RJ 45 Connector Pin Assigns Pin 10 100Base T Signal Name XMT XMT RCV NC NC RCV NC NC GQ N UNO 3072A 3074A User Manual 62 7 Power Connector PWR Table A 9 Power connector assignments 1 V 10 36Vpc 2 V 3 Field Ground A 8 PS 2 Keyboard and Mouse Connector Table A 10 Keyboard amp Mouse Connector Pins Pin Signal Name KB DATA MS DATA GND VCC KB Clock MS Clock O OI Ww 63 Appendix A 9 USB Connector USB1 USB4 amp CN7 Table A 11 USB Connector Pin Assignments Pin Signal Name Cable Color 1 VCC Red 2 DATA White 3 DATA Green 4 GND Black UNO 3072A 3074A User Manual 64 10 VGA Display Connector DVI Ito DVI amp VGA Cable or Converter Table A 12 VGA Adaptor Cable Pin Assignmen Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 NC 13 H SYNC 14 V SYNC 15 NC 65 Appendix 11 Clear CMOS CN3 This jumper is used to erase CMOS data and reset system BIOS informa tion Follow the procedures below to clear the CMOS 1 Turn off the system 2 Close jumper CN3 1 2 to clear CMOS 3 Remove
27. alling Power Cable UNO 3072A 3074A provides an internal backup power source so that it can provide power for a PCI Blower external video card that required additional power or other external devices You can use the power cable from accessory package see section 1 5 Yellow 12V Black GND Black GND Red 5V UNO 3072A 3074A User Manual 50 UNOB 3036 BP external power See H FAN CN4 Dry Contact as CNIS Wet Contact EA 3 7 BIOS Setup and System Assignments UNO 3072A 3074A adapts Advantech s SOM 6763 CPU module Fur ther information about the SOM 6763CPU module can be found in user manual of SOM 6763 You can find this manual on the driver and utility CD of UNO 3072A 3074A in the accessory package Please note that you can try to LOAD BIOS DEFAULTS from the BIOS Setup manual if the UNO 3072A 3074A does not work properly 31 Chapter 3 3 8 Rubber Foot Installation UNO 3072A 3074A provides Rubber Foot for two purpose lt 1 gt Anti Shock Vibration purpose and lt 2 gt protect the surface of Chassis from scratch Please find the rubber foot in accessory box shown below Please peel the non stick paper and put the rubber foot on the location that has been circled in red UNO 3072A 3074A User Manual 52 APPENDIX System Settings and Pin Assignments Appendix System Settings and Pin A 1 System I O Address and Inte
28. ble RAID in System BIOS Use the instructions included with your motherboard to enable RAID in the system BIOS I Click Del to enter the BIOS Setup program after the Power On Self Test POST memory test begins 2 Click the Integrated Peripherals menu 3 Click the OnChip IED Device menu 4 Switch the SATA Mode option to RAID to enable Intel RAID Tech nology 5 Click F10 to save the BIOS settings and exit the BIOS Setup pro gram Create a RAID Volume Use the following steps to create a RAID volume 1 When the Intel Rapid Storage Technology option ROM status screen appears during POST press Ctrl and 1 at the same time to enter the option ROM user interface up 0 8 1007 1 Copur ight 0 2003 85 Iutel all Rights Reserved RAID Volunes None defined Physical Bisks Port Brive Model Serial 5190881105 SLYC91PP 2 STORRRISN SRR01P4X Press 0 to enter Configuration Utilitu 35 Chapter 2 2 ool 1 Create RAID Volume and press Enter r option Copyright C 2003 85 Intel All Rights hc Create RAID 3 Reset Disks to Non RAID ST988817SH Size Type Status Vol ID 74 gt N 3 Use the up or down arrow keys to select ihe RAID level and press Enter RAID Level Disks Strip Size Capacity Vglune RAIDB Stripe Select Disks 128KB 149 1 GB Create Volune Enter a string between 1 and 16 characters in length that can be used to
29. ce personnel If one ofthe following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW v 10 C 14 OR ABOVE 60 C 140 THIS COULD DAM AGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT 16 CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORD ING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage 1 To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC
30. d in the system BIOS setup Please refer to Appen dix A 9 for its pin assignments 2 10 Battery Backup SRAM UNO 3072A 3074A provides 512 KB of battery backup SRAM This ensures that you have a safe place to store critical data You can now write software applications without being concerned that system crashes will erase critical data from the memory There is a BTR LED in the front panel of the UNO 3072A 3074A Figure 2 13 Please replace the lithium battery if the BTR LED is activated nm Ty Exi Do RO Q Q Figure 2 13 LED Location for Battery Backup 1 31 Chapter 2 2 10 1 Lithium Battery Specification Type BR2032 Using CR2032 is NOT recommended Output voltage 3 Vpc Location Mainboard of UNO 3072A 3074A Figure 2 14 When the voltage of battery lt 2 5 Vpc BTRY LED will light up Figure 2 14 Lithium Battery for SRAM 2 11 Reset Button Press the Reset button to activate the reset function SW1 UNO 3072A 3074A User Manual 32 2 12 Power Button UNO 3072A 3074A standard power is ATX type Please press the Power button to power on or power off The power switch bottom fea tured safety switch which user need to use finger tip to continue press 4 second to shut the system down It protect the system won t be accidently shut down UNO 3072A 3074A had also offers AT power mode available It can setup in BIOS or close the jumper o
31. dom 5 500Hz 1 Oct min 1hr axis Power Supply 9 36 Operating Temperature 10 60 C 14 140 F Note The temperature inside the chassis may be 5 to 10 C higher than the ambient temperature To ensure stable performance please make sure the operating temperature of the installed PCI add on card is higher than 60 C Relative Humidity 5 95 40 C non condensing Power Consumption 25 W Typical Power Requirement Min 72 W 9 36 e g 24 V 3A Chassis Size WxHxD UNO 3072A 140 x 238 x 177 mm 5 5 x 9 3 x 7 UNO 3074A 181 x 238 x 177 mm 7 5 x 9 3 x 7 Mounting Wall Panel Stand mounting Weight UNO 3072A 4 5 kg UNO 3074A 5 0 kg Software OS WinXP Embedded CE 6 0 2000 XP Windows 7 Linux Watchdog Timer Programmable 256 levels timer interval from 1 to 255 sec with Fintek F75111 Keyboard amp Mouse Optional cable wiring PS 2 connector UNO 3072A 3074A User Manual 4 1 3 Safety Precautions The following messages inform how to make each connection In most cases you will simply need to connect a standard cable Note Note Note Always disconnect the power cord from your chas sis whenever you are working on it Do not connect while the power is on sudden rush of power can damage sensitive electronic components Only experienced electronics personnel should open the chassis Always ground yourself to remove any static elec tric charge before touching UNO 3072A 30
32. eSet 0 Gate source from CTR1Gate control bit Default 1 Gate source from digital input 2 012 channel 2 7 8 Counter Output Destination You can choose the output destination of counter 0 and counter 1 by setting Output Destination control bits CTROOutSet and CTR1OutSet Table 2 12 Counter Output Destination Control Bit CTROOutSet 0 Output destination to CTROOut status bit Default 1 Output destination to CTROOut status bit and digital output 2 DO2 channel CTR1OutSet 0 Output destination to CTR1Out status bit Default 1 Output destination to CTR1Out status bit and digital output 3 DO3 channel 2 7 9 Counter Interrupt Flag The interrupt flag bit is a flag indicating the status of an interrupt It is a readable writable bit To find the status of the interrupt you have to read the bit value to clear the interrupt you have to write 1 to this bit This bit must first be cleared to service the next coming interrupt Besides you can choose if counter 0 or counter 1 generate interrupt signal by configuring CTROIntSet and control bit Table 2 13 Counter Interrupt Flag Control Bit CTR1F Counter Interrupt Status Read 0 No interrupt 1 Interrupt occur Write 0 Don t care 1 Clear interrupt CTROIntSet CTR1IntSet Counter Interrupt Control 0 Disable Default 1 Enable
33. ernet RJ 45 Connector LAN1 LAND2 62 Table A 8 Ethernet RJ 45 Connector Pin Assigns 62 PS 2 Keyboard and Mouse Connector 63 Table A 10 Keyboard amp Mouse Connector Pins 63 USB Connector USB1 USB4 amp CN7 64 Table A 11 USB Connector Pin Assignments 64 VGA Display Connector 65 Table 12 Adaptor Cable Pin Assignmen 65 Programming the Watchdog Timer 72 v 72 ix Table of Contents UNO 3072A 3074A User Manual Overview This chapter provides an overview of UNO 3072A 3074A specifications Sections include Introduction Hardware specification Safety precautions Chassis dimensions Chapter 1 Overview 1 1 Introduction Advantech s UNO 3072A 3074A are Intel Dual Core Atom based Embedded Automation Computers with up to four PCI slots that provide an excellent performance to power consumption ratio Gigabit LAN sup ports the teaming function with fault tolerance link aggregation and load balancing Different from general industrial PCs UNO 3072A 3074A is more compact and reliable with a fanless and cableless design They are also equipped with two IEEE 1394b bilingual interfaces which allow users to connect their own devices for machine vision Critical data can be saved on the battery backup S
34. he user can choose to enable or disable the interrupt function by writing its corresponding value to the interrupt disable enable control bit in the interrupt control register as shown in Table 2 14 19 Chapter 2 2 5 7 Interrupt Triggering Edge Control The interrupt can be triggered by a rising edge or a falling edge of the interrupt signal as determined by the value in the interrupt triggering edge control bit in the interrupt control register as shown in Table 2 15 Table 2 4 Interrupt Triggering Edge Control DIOTE amp Triggering edge of interrupt signal 0 Falling edge trigger 1 Rising edge trigger 2 5 8 Interrupt Flag Bit The interrupt flag bit is a flag indicating the status of an interrupt It is a readable writable bit To find the status of the interrupt you have to read the bit value To clear the interrupt you have to write 1 to this bit This bit must first be cleared to service the next coming interrupt Table 2 5 Interrupt Flag Bit Values DIOF amp DI1F Interrupt Status Read 0 No interrupt 1 Interrupt occur Write 0 Don t care 1 Clear interrupt Note UNO 3072A 3074A provides built in examples to show how to deliver digital input functionality Refer to console mode examples in C Program Files Advantech UNO UNO_IsaDIO Exam ples Console Please install DIVO driver from the UNO CD to use these examples UNO 3072A 3074A User Manual 20
35. hot swap LEDs Power Standby HDD Alarm for battery backup 4 COM ports Tx Rx LAN Active Status Optional 4x Programmable LED while COM ports Tx Rx disable PCI bus Slot Power 12V 3A 12V 08A S5V 6A 33V 6A 3 3 1 5 Note Total power total combined power consumption on the PCI slots should be less than 20W 4 ch Isolated Digital Input Wet Contact 010 013 1 500 isolation 1 500 ESD protections 50 70 V pc over voltage protection 50 Vpc input range and 3 kHz speed Input Voltage Range Dry Contact Logic level 0 open Logic level 1 close to GND Wet Contact Logic level 0 3V 3V Logic level 1 10 50 V 10 50V 4 ch Isolated Digital Output DO0 DO3 1 500 isolation and 200 mA max channel sink current 2 options after hot reset Reset all digital output or keep last status 5 40 Vpc output range to open collector and 3 kHz speed Two 16 bit Counters Timers Counter source DII amp DI3 Pulse output DO2 amp Can be cascaded as one 32 bit counter timer Down counting preset counting value 3 Chapter 1 Interrupt handling speed 40 kHz Internal timer time base 100 kHz 10 kHz 1 kHz 100 Hz Anti Shock 20 Wall mounting IEC 60068 section 2 27 half sine 11 ms w HDD 50 Wall mounting IEC 60068 section 2 27 half sine 11 ms w CF Anti Vibration 2 Grms w CF IEC 60068 sec 2 64 random 5 500Hz 1 Oct min 1hr axis 1 Grms w HDD IEC 60068 sec 2 64 ran
36. is Grounding Connecting Power Connecting a Hard Disk BIOS Setup and System Assignments Chapter 3 Initial Setup 3 1 Inserting a CompactFlash Card UNO 3072A 3074A provides two CompactFlash slots One slot CF2 on the daughterboard is accessible from the top of the system where you can insert your CompactFlash card directly The other slot CF1 is inside UNO 3072A 3074A on its motherboard You can set SW3 1 to decide which one is the master SW3 1 on motherboard refer to Figure A 4 OFF External CF master CF1 Slave default ON External CF master CF1 Slave Note Only one CompactFlash can be set as master Internal amp external CompactFlash doesn t support Hot Swap Needs to use Fixed Disk Mode CompactFlash to install OS Following 1s the procedure for the installing a CompactFlash card in the internal slot CN3 of your UNO 3072A 3074A Please follow these steps carefully 1 Remove the power cord 2 Unscrew the four screws from the top cover of UNO 3072A 30744 3 Remove the top cover 4 Plug a CompactFlash card with your OS and application program into a CompactFlash card slot on mainboard 5 Screw back the top cover with four screws 3 2 Connecting Power Connect the UNO 3072A 3074A to a 10 36 power source The power source can either be from a power adapter or an in house power source UNO 3072A 3074A User Manual 42 3 3 Installing a Hard Disk The procedure for installing a hard dis
37. k is listed below Please follow these steps carefully 1 Remove the power cord 2 Unscrew the five screws from the bottom cover as shown below 43 Chapter 3 4 Install the HDD in HDD bracket and secure with four screws Please refer to pictures below Please mind the direction of the SATA hard drive connector like below 5 SATA HDD Installation Install HDD into HDD bracket and fix with screw UNO 3072A 3074A User Manual 44 Connect cable and power cable HDD side and motherboard side The correct connection way is shown below 7 d os 4 la 6 KS Wess VN U i es ULL A WW ij jj 4 LAU VR D ER LL V LO I LLL I I I DA M GOO UT e D V V D I FUA jj P WO MN Uh 0 i NL W 45 Chapter 3 3 4 Installing a PCl bus Card The procedure for installing a PCI bus card into the UNO 3072A 3074A 15 listed below Please follow these steps carefully 1 2 3 4 Remove the power cord Remove the upper cover of UNO 3072A 3074A Unscrew the screw of a PCI bracket and remove it Remove the Slot Cover on PCI slot II HIHI AMI UNO 3072A 3074A User Manual 46 6 Screw back upper cover with the eight screws
38. llow these steps 1 the DB 9 RS 232 cable with brackets from accessory box 2 Connect the end of the cable on CN17 and CN18 of the main board 15 Chapter 2 3 Boot up reset the system press Del to enter into BIOS 4 Select Integrated Peripherals Super I O device Onboard Serial Port 1 and Onboard Serial Port 2 5 Change the IRQ and IO address from Disablde to the above setting 6 Press F10 or Back to Save and Exit Setup to finish setup change 7 Fasten the COM port bracket on the UNO 3072A 3074A system like below The IRQ and I O address range of COM3 and COM4 are listed below 2E8H IRQ4 COM4 2F8H IRQ3 2 4 LAN Ethernet Connector The UNO 3072A 3074A is equipped with a Intel 82574L Ethernet LAN controller that is fully compliant with IEEE 802 3u 10 100Base T CSMA CD standards The Ethernet port provides a standard RJ 45 jack on board and LED indicators on the front side to show its Link Green LED and Active Yellow LED status UNO 3072A 3074A User Manual 16 2 5 Isolated Digital Input The UNO 3072A 3074A has 4 isolated DI channels designated DIO DI3 2 5 1 Pin Assignments The connector type of UNO 3072A 3074A is plug in screw terminal block that enables you to connect to field I O devices directly witho
39. lowing info ready Product name and serial number Description of your software OS version software etc A complete description of the problem The exact wording of any error messages UNO 3072A 3074A User Manual iv Safety Instructions 1 2 3 Read these safety instructions carefully Keep this User s Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for clean ing For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Drop ping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before con necting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or elec trical shock Never open the equipment For safety reasons the equipment should be opened only by qualified servi
40. ments 17 2 5 2 Isolated Inputs eerte eere 17 Figure 2 5 Digital Input Wet Contact Diagram 18 2 5 3 Interrupt Function of the DI Signals 18 234 Level 45 ener e 18 2 5 5 Interrupt Control Register 18 Table 2 2 Interrupt Control Register Bit Map 18 2 5 6 Interrupt Enable Control Function ald Table 2 3 Interrupt Disable Enable Control 19 2 5 7 Interrupt Triggering Edge Control 19 Table 2 4 Interrupt Triggering Edge Control a 2 5 8 Interrupt Flag Bit Table 2 5 Interrupt Flag Bit Values Onboard Isolated Digital Output 2 6 1 Pin Assignments sited tion Sen ed Heec uenis Figure 2 6 Digital Output Connector Pin Assignments 21 Table 2 6 Digital Output Connector Signals 21 2 6 2 Power On Configuration 22 Figure 2 7 Location of CN27 sess 22 vii Table of Contents 2 7 2 8 2 9 2 10 Nt NR NNN Chapter Sunu Uo BO WRU U2 W Lo W Wo Table 2 7 Digital Output Power On Configuration 22 2 6 3 a Isolated Outputs Onboard Isolated Counter Timer 2 7 1 Counter Timer Control Register Table 2 8 Counter Timer Control Register Bit Map 24 2 7 2 Counter 0 Function Block sese Figure
41. n CNS in order to use AT mode Figure 2 15 Hardware AT mode Jumper Location 2 13 Audio UNO 3072A 3074A supports audio Line out function 33 Chapter 2 2 14 IEEE1394 UNO 3072A 3074A equipped Dual IEEE 13946 also known as FireWire connector interfaces supports transfer rates up to 800Mb s IEEE 1394 1 the one of the most popular interface for PC peripherals and customer electronics including digital video CD RW DVD music syn thesizers This interface is also very popular in Camera for Machine Vision application in industrial automation The interface on UNO 3072A 3074A is type B interfaces If the current 1394 equipment is with type A user need to buy extra converter cable from IEEE 1394 equipment vendor LAUTE carries power LTT TELE power also used for bilinguallto Beta uno 3184 Bi lingual SS Bi lingual Bi lingual Bi lingual Beta only Da Bi lingual UNO 3072A 3074A User Manual 34 2 15 Hard Drive RAID Support In order to install an operating system onto a RAID volume the RAID option must be enabled in the system BIOS a RAID volume must be cre ated and the F installation method must be used to load the Intel Rapid Storage Technology driver during operating system setup Before you start please make sure that two SATA hard drives have been mounted in system A USB floppy will be also required for some addi tional files Ena
42. r RAID driver 37 Chapter 2 Note Nothing will happen immediately after pressing F6 Setup will temporarily continue loading drivers You will then be prompted with a screen asking you to load support for mass storage device s 2 Press S to Specify Additional Device Matrix Storage Console e Yew Actions Hep Inel RAID Controllers Information 4 Inte R 822016HM SATA RAID Controller nas B Ans Value r eg iama Stats Namal lumos Yer intel guma RAID Hard Dives E Por 51380115 En 3 Poni 2 umbar cl Hard Diivee 2 Hard Drive Member STSEOBI1AS Hard Drive Member 2 STS60817SM Parent Aray 3 When you see a prompt that says Please insert the disk labeled Manufacturer supplied hardware support disk into Drive insert a floppy disk containing the following files IAAHCLINF IASTOR INF IASTOR CAT IASTOR SYS and TXTSETUP OEM Note Use the Floppy Configuration Utility to create a floppy disk with the necessary files or copy required file from driver folder 4 Press Enter 5 Select your controller from the list of available SCSI adapters Use the up and down arrow keys to scroll through the list as all control lers may not be visible Note For UNO 3072A 3074A pick Intel 8 for UNO 3272 3282 pick Intel ICH7MDH UNO 3072A 3074A User Manual 38 Press Enter to confirm your cont
43. roller and continue At this point you have successfully installed the driver and Windows setup should continue Leave the floppy disk in the floppy drive until the system reboots Windows setup will need to copy the files again from the floppy to the Windows installation folders Once Win dows setup has copied these files again remove the floppy disk so that Windows setup can reboot as needed During Windows setup create a partition and file system on the RAID volume as you would on any physical disk Note If you wish to use the Intel Rapid Storage Technology user interface in Windows you will need to install Intel Rapid Storage Technology by running the Setup exe process after these steps have been completed and the operating system has been successfully installed Intel R Matrix Storage Console c e Yew Actions Hep i Ine RAID Controllers Information iol 8220 1GHM SATA RAID Controller Anays Paramete Value S E Anas 0000 Statue Namal 3 Velumes System Volume Yer Volume J 77 B RAID Hard Dives l E Pori Q T9808114S x Number of Hard Dives 2 See Hard Drive Member STSEOBI1AS Hard Drive Member 2 STS608175M Parent Aray 0000 39 Chapter 2 UNO 3072A 3074A User Manual 40 Initial Setup This chapter introduces how to initialize the UNO 3072A 3074A Sections include Introduction Inserting a CompactFlash Card Chass
44. rrupt Assignments Assignments Table 1 UNO 3072A 3074A System I O Port Address Device Range Device 0000 OCF7 PCI bus 0000 000F Direct memory access controller 0010 001F Motherboard resources 0020 0021 Programmable interrupt controller 0022 003F Motherboard resources 0040 0043 System timer 0044 005F Motherboard resources 0060 0060 Standard 101 102 Key or Microsoft Natural PS 2 Key board 0061 0061 System speaker 0062 0063 Motherboard resources 0064 0064 Standard 101 102 Key or Microsoft Natural PS 2 Key board 0065 006F Motherboard resources 0070 0073 System CMOS real time clock 0074 007F Motherboard resources 0080 0090 Direct memory access controller 0091 0093 Motherboard resources 0094 009F Direct memory access controller 00 0 00A1 Programmable interrupt controller 00A2 OOBF Motherboard resources 00 00DF Direct memory access controller 00 OOEF Motherboard resources 00FF Numeric data processor 01F0 01F7 Primary IDE Channel UNO 3072A 3074A User Manual 54 0274 0277 ISAPNP Read Data Port 0279 0279 ISAPNP Read Data Port 02F8 02FF Communications Port COM2 02E8 02EF Communications Port COM4 0378 037F Printer Port LPT1 03B0 03BB Mobile Intel 965 Express Chipset
45. uniquely identify the RAID volume This name is case sensitive and can not contain special characters 4 Unless you have selected RAID 1 use the up or down arrow keys to select the strip size and press Enter Press Enter to select the physical disks 6 Select the appropriate number of hard drives by using the up or down arrow keys to scroll through the list of hard drives and press Space to select the drive When finished press Enter UNO 3072A 3074A User Manual 36 2 Delete RAID Volune 3 Reset Disks to Non RAID 4 Exit DISK UOLUME INFORMATION RAID Volunes Level Strip Size Status Bootable B Voluned RAIDB Str i pe 128KB 149 168 Yes rmgsiGqi DISKS Port Drive Model Serial 8 Size Type Status Vol ID 8 35198881185 SLYC91PP 74 568 Menbe 2 31988817S E 74 568 Select the volume size and press Enter Press Enter to create the volume 9 At the prompt press Y to confirm volume creation 10 Select 4 Exit and press Enter 11 Press Y to confirm your exit Install the RAID Driver Using the F6 Installation Method Perform the following steps to install the Intel Rapid Storage Technology driver during operating system setup 1 Press F6 when you see a message in the status line that says Press F6 if you need to install a third party SCSI or RAID driver This message appears at the beginning of Windows XP setup during text mode phase Press F6 if you need to install a third party SCSI o
46. ut additional accessories Figure 2 4 and Table 2 4 shows its pin assignment as well as signal description w jw D D DO COM Figure 2 4 Digital Input Connector Pin Assignments 2 5 2 Isolated Inputs Each of isolated digital input channels accepts 0 50 Vpc voltage inputs and accepts bi directional input The voltage range is 3 3 Vp for logic 0 low 50 10 Vpc and 10 50 for logic 1 high It means that you can apply positive or negative voltage to an isolated input pin Vin channels share two common pins I GND Figure 2 8 shows how to connect an external input source to an UNO 3072A 3074A isolated input channel Please note that DIO and DI2 may be configured as gate control pins of Counter 0 and Counter 1 While and DI3 may be configured as input pins of Counter 0 and Counter 1 17 Chapter 2 External Internal DOCOM 15V m CN15 Jumper setting 0 f DIO Figure 2 5 Digital Input Wet Contact Diagram 2 5 3 Interrupt Function of the DI Signals DIO and can be used to generate hardware interrupts Users can setup the configuration of them by programming the interrupt control register The channels are connected to the interrupt circuitry Users can disable enable interrupt function select trigger type or latch the port data by set ting the Interrupt Control Register of
47. ut modification 11 Chapter 2 2 2 4 RS 232 422 485 Selection and support 9 wire RS 232 RS 422 and RS 485 interfaces The system detects RS 422 or RS 485 signals automatically in RS 422 485 modes To select between RS 422 485 and RS 232 for COM1 adjust CN28 To select between RS 422 485 and RS 232 for COMO adjust CN29 You can refer to figures below to set the CN28 and CN29 Note Please refer to Appendix A 2 Figure for location of CN28 and CN29 location Jumper setting for RS 422 485 interface Default setting ERI Figure 2 2 RS 422 485 Jumper Setting Jumper setting for RS 232 interface BERB Figure 2 3 RS 232 Jumper Setting UNO 3072A 3074A User Manual 12 2 2 5 Terminal Resistor Setup for RS 422 485 The onboard termination resistor 120 Ohm for COM1 COM2 can be used for long distance transmission or device matching Default Open Each terminal resistor responds to different channels for RS 422 485 Usually these resistors are needed for both ends of the communication wires and the value of the resistors should match the characteristic imped ance of the wires used Table 2 1 Terminal Resistor Settings COM Port Switch No Pin Setting Description COM1 SW4 1 ON 120 Ohm between Data Data RS 485 Or 120 Ohm between Tx Tx RS 422 OFF Open Default 2 ON 120 Ohm between Rx Rx RS 422 OFF Open Default COM2 SW5 1 ON 120 Ohm between
Download Pdf Manuals
Related Search