Specification of Battery Charger HT
Contents
1. 70 C the normal temperature 20 50 C and relative humidity is 5 95 In the warehouse there should not be harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box should be above ground at least 20cm height and 50cm away from wall thermal source and vent Under this requirement product has 2 years of storage period and should be rechecked when over 2 years 9 Reliability requirements MTBF standard environmental temperature load requirement 50K hours testing condition 25 C full load testing proved value 10 Charging Curve 13 54CC Time shut off point2. Power efficiency Vin 220Vac rated load 4 3 Protection characteristics 4 4 No Item Technical specification Remark The charger output voltage does not exceed set the maximum 1 cs charging voltage of the battery voltage protection Aluminum shell the inside temperature gt 65 C Automatic 2 Thermal Shutdown protection Transformer temperature gt 110 C Automatic Shutdown 3 Current The charger output current does not exceed a set battery charge limiting current At CC mode protection ae Short circuit protection should be automatically recovery after 4 Short circuit n remove the condition protection 5 Reverse When output wires are reversely connected to the battery the polarity charger will not operate and will work normally when DC wires protection are correctly connected Charging indicator No Item Status Remark 1 LED1 Red Power on LED2 Green 2 LED1 Red Charging LED2 Red 3 LED1 Red Fully charged LED2 Green 4 Charging Voltage Display Yes 5 Charging Current Display Yes Safety amp EMC No Item Standard or test condition Remark i MCE MRoHs GS UL Safety CCC SAA PSE KC EN55014 1 2006 A2 2011 EN55014 2 1997 A2 2008 EMC EN61000 3 2 2006 A2 2009 EN61000 3 3 2008 EN60335 1 2012 6 LVD EN60335 2 29 2010 EN62233 2008 Remark Discrimination A Function OK unde
3. Him Ting Enterprise Co Unit H507 4 F Phase 2 Kwai Shing Industrial Building 42 46 Tai Lin Pai Road Kwai Chung Hong Kong Tel 852 35681189 Fax 852 81471728 E mail sales himting com Specification of Battery Charger HT 259 LITHIUM BATTERY CHARGER Aluminum enclosure General The series HT 259 330x175x90mm aluminum shell charger with reverse polarity protection function 1 Main product specification Model HT 259 M tput E la is 21V 0 2 voltage Li ion 50A 45 Output current BA das 5S Battery Specifications 1050W Max output power 90 132Vac W 180 260Vac 380Vac Input voltage 3 Environmental condition No Item Technical specification Remark 1 hit 5 95 Humidity With package 2 lt 3000m Altitude Work normally 4 Electrical characteristics 4 1 Input characteristic No Item Technical specification Remark 1 110Vac W230Vac Rated input voltage 2 90 132Vac W 180 260Vac 380Vac Input voltage range 3 50 60 Hz AC input voltage frequency 4 2 Output characteristic or charge stages No item Technical specification Remark 1 E 18 5V Nominal voltage 2 Li ion 21V Vout cc lt Vout constant current 50A 3 Vout 50A constant voltage Vout 4 pE 5 CC Transition Current 2 5A gt 0 5 7 286
4. r technical requirement range Discrimination R Physical damage or failure of equipment are not allowed but damage of protection device fuse caused by interference signal of outside is allowed and the whole equipment can work normally after replacement of protection device and reset of running parameter 6 Environmental testing requirements No Item Technical specification Remark High environmental 1 40 C temperature ambient Features OK operating Low environmental 2 10 C temperature ambient Features OK operating Work normally after recovery 3 70 C High temperature storage under normal temperature for 2 hours Work normally after recovery 4 40 C under normal temperature for 2 Low temperature storage hours Mechanical characteristic Shell material Aluminum Outline dimension L W H 330x175x90mm Input socket meets IEC standard AC wires 1 5m length DC wire 1 5m length Net Weight 6 5Kg Package transportation amp storage 8 1 Package There is product name model name of manufacturer safety approval serial number User Manual and packing list in the package box 8 2 Transportation Suit for transportation by truck the products should be Placed in cool dry place and loaded and unloaded carefully 8 3 Storage Products should be stored in package box when it is not used And Warehouse extreme temperatures should be 40
Download Pdf Manuals
Related Search