SFP+ Test Adapter - Wilder Technologies
Contents
1. Actual DC Block may differ than part shown Low Speed Connector 4 SMAs male for High Speed Testing es SFP Plug Connector Assembly Figure 1 The SFP HCB Test Adapter tests to the requirements of the Host Compliance Board Plug Note Coaxial cables shown are illustrated shorter than those used in the test adapter Page 3 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual 50 Ohm RF Termination yi SMAs male Female one of four for High Speed shown Optional Accessory Testing DC Block One of four shown Optional Accessory Note Actual DC Block may differ than part shown Housing SFP Receptacle Switch Module Connector a SFP Receptacle Figure 2 The SFP MCB Test Adapter tests to the requirements of the Module Compliance Board Receptacle Note Coaxial cables shown are illustrated shorter than those used in the test adapter NOTE The metal shell of both the plug SFP TPA HCB P and receptacle SFP TPA MCB R connectors tie high speed ground to chassis ground The low speed 12 position receptacle and plug connectors are keyed and latching Molex part number 43645 1200 for the plug TPA and 43650 1204 for the receptacle TPA The mating connector housings and contact pins for 26 30awg wire are Molex part number 43640 1201 for the 12 position housing and 43031 0011 for the plug contacts used with2. Legislation cccccsssscccecessessnecceecescessaeaeeeeeesssesesaeseeeeesesenaees 29 WEEE Compliance Statement cccccssscccccsssessssececeeecessesaeecececsseeseeaeaeeececescaeaeeeeeessessessaaeeesens 29 Glossary OF TERMS 2 2serchscancacsgsaaci gteccceetesaseaiecesssagesksseens Ea tsa tectem eileen ee 30 DIVE cas cece eee 4 costs E E E EEE E E ost seeuceceaceaitess EE ET 31 Page 2 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Introduction This user s guide documents the SFP Plug and Receptacle Test Adapters SFP TPA HCB P and SFP TPA MCB R and the Low Speed HCB and MCB Switch Module assemblies The two test adapter types shown in Figures 1 and 2 test SFP interface cables hosts and modules to the requirements of the SFF 8431 and SFF 8083 specifications The TPA HCB P and TPA MCB R test adapter assemblies allow easy access via SMA connections to measure or inject data signals NOTE To avoid damaging the cables use the handling techniques described in the Care and Handling section before making any connections or configuring a test setup Always use a static safe workstation when performing tests as explained in the Electrostatic Discharge Information section SFP Plug Switch Module Assembly 50 Ohm RF Termination Female one of four shown Optional Accessory DC Block One of four shown Optional Accessory Note
3. MQ of isolation from ground Acceptable ESD accessories may be purchased from a local supplier WARNING These techniques for a static safe work station should not be used when working on circuitry with a voltage potential greater than 500 volts Page 9 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual User Model The SFP TPAs are capable of performing to the requirements of SFF 8431 and SFF 8083 limited only by the specifications environmental care and handling of this document In the case where the laboratory source or load is not used in the test it must be replaced with RF terminations on each unused signal RF terminators are optionally offered by Wilder Technologies The following examples are suggestions for possible testing setups In this first example a SFP TPA MCB R and associated Switch Module assembly is used to test a SFP Module MCB Switch Module Physical Links Under Test ae SFP Module Under Test Laboratory SFP TPA MCB R Sourced Signal Block Laboratory Load Page 10 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The second example shows a SFP TPA HCB P and associated Switch Module assembly is used to test a host In the case where the laboratory source or load is not used in the test it must be replaced with RF terminations on e
4. VCT Pin 11 Black NA Vcct module transmitter power supply GND Pin 12 Black NA VeeR and VeeT RF Ground Page 17 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Table 4 SFP Plug and Receptacle Pin Assignments Pin Description pioneers pee Color ID for Data Color Identification A HCB MCB Line Polarity HCB MCB RF Ground N A Black Insulation NA Tx Fault N A Black Insulation NA Tx Disable N A Black Insulation NA SDA a Pa N A Black Insulation NA SCL N A Black Insulation NA Mod_ABS 6 Pamens N A Black Insulation NA RSO N A Black Insulation NA Rx_LOS e Pms N A Black Insulation NA RS1 gt Pms N A Black Insulation NA RF Ground N A Black Insulation NA RF Ground N A Black Insulation NA RD RD oo Blue Label RF Ground N A Black Insulation NA VccR N A Black Insulation NA VecT N A Black Insulation NA RF Ground N A Black Insulation NA TD TD ed Yellow Label T0 T Yellow Label RF Ground 20 P2 J2 Pin 1 Pin 12 N A Black Insulation NA Page 18 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Electrical Specifications NOTE All specifications in this manual are subject to change Table 5 Electrical Specifications TPA SPECIFICATION MIN TYP MAX NOTES Insertion Loss db at 5 GHz 1 18 0 97 0 87
5. 013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The following figure refers to the pin description table for the receptacle connector i SMAs for High Speed Testing Color ID for Differential Pair See Table 2 amp 4 Color ID for Data Line Polarity See Table 4 Pin 1 End Ref Low Speed Connector Receptacle See Table 3 and 4 Connector See Table 4 Figure 6 Cable Connectors SFP TPA MCB R shown Page 15 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The following figure refers to the SFP TPA MCB R Switch Module assembly Refer to SFF 8431 for test details and settings of the Switch Module assembly Note The default settings for switch S1 are Pin 1 On Pin 2 Off Pin 3 Off Pin 4 NC The mating 3 position receptacle connector housings and contact receptacles for 22 30awg wire are provided with each SFP TPA MCB R Switch Module assembly allowing the user to create custom Switch Module cables Molex part number 22 01 2035 for the housings and 08 55 0102 for the receptacle contacts Replacement plug parts can be purchased through Molex distributors TX_DIS S1 1 S 5 Switch On RS1 S1 3 Switch Off O x x or Fin mS R EoN xe xa RSO S1 2 Switch Off Figure 7 SFP TPA MCB R Switch Module P3 3V_Rx P3 3V_Tx o ol ol R6 R3 P3_3V_Tx 47k
6. 47k RI GREEN Oe l J4 4 2 4 AA 2 4 3 3 2 lol LED 1 1k T4Aco4 E2 R2 GREEN uie HDR_SHRD_3X1 hg 1 2 4 je 2 6 5 i s C i LED P3 3V_Tx 70 74ACO4 7AACO4 P3_3V_Rx O UIE oj ol P3_3V_Tx R11 R12 7 Not Populated i 1o 74AC04 UIF 74AC04 Figure 8 SFP TPA MCB R Switch Module Schematic Page 16 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Table 2 SMA Cable Connectors High Speed LABEL COLOR ID FOR DIFFERENTIAL PAIR DESCRIPTION RD Blue Receive positive for Host Transmit positive for Module RD Blue Receive negative for Host Transmit negative for Module TD Yellow Transmit positive for Host Receive positive for Module TD vale Transmit negative for Host Receive negative for the Module Table 3 SFP TPA 12 Position Cable Connector Low Speed LABEL PIN NO COLOR ID FOR HCB MCB DESCRIPTION GND Pin 1 Black NA VeeR and VeeT RF Ground TXF Pin 2 Black NA Tx_Fault Transmit fault TXD Pin 3 Black NA Tx_Disable Transmit disable SDA Pind Black NA SDA IC Data for DDC scL Pin5 Black NA SCL I C Clock for DDC ABS Pin 6 Black NA MOD_ABS Module absent RSO Pin 7 Black NA RSO Rate select 0 LOS Pin 8 Black NA Rx_LOS Loss of Receive Signal RS1 Pin 9 Black NA RS1 Rate select 1 VCR Pin 10 Black NA VccR module receiver power supply
7. DER TECHNOLOGIES LLC assumes no liability for the results of the use of its components in conjunction with other electric electronic or mechanical components circuits and or systems The foregoing constitutes the sole and exclusive remedy of the Buyer and the exclusive liability of WILDER TECHNOLOGIES LLC and is IN LIEU OF ANY AND ALL OTHER WARRANTIES STATUTORY IMPLIED OR EXPRESSED AS TO MERCHANTABILITY FITNESS FOR THE PURPOSE SOLD DESCRIPTION QUALITY and PRODUCTIVENESS OR ANY OTHER MATTER Without limiting the foregoing in no event shall WILDER TECHNOLOGIES LLC be liable for loss of use profit or other collateral or for special and or consequential damages RETURNED GOODS WILDER TECHNOLOGIES LLC will accept only those goods for return that have been authorized for return All goods authorized for return shall be assigned a Returned Material Authorization RMA Number The RMA Number shall be clearly marked on the shipping container s and all documentation accompanying the goods authorized for return The RMA Number shall be assigned by WILDER TECHNOLOGIES LLC pursuant to the conditions set forth in Paragraph 4 WARRANTY UNITED STATES GOVERNMENT CONTRACTS In the event this offer is accepted under Government contract WILDER TECHNOLOGIES LLC agrees to accept clauses required by Government regulations and to waive WILDER TECHNOLOGIES LLC conditions inconsistent therewith WILDER TECHNOLOGIES LLC certifies that it is a regular manu
8. Form Factor Pluggable connection SFP Host The SFP Host is the fixed end of the connection supporting IEEE 802 3 clauses 38 49 52 59 or 68 8 GFC 10 GFC and 10GSFP Cu serial protocols SFP Module The SFP Module is the moveable end of the connection supporting IEEE 802 3 clauses 38 49 52 59 or 68 8 GFC 10 GFC and 10GSFP Cu serial protocols SFP TPA SFP Test Point Access A specialized assembly that interfaces to a SFP host or module and enables access of signals for measurement or stimulation Victim A signal carrier on a system that has a response imposed on it by other signals in the system Page 30 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Index AC coupled 4 Cable Bend Limits 6 Cable Tension Pull Forces 6 Cable Twisting Torque 6 Care and Handling 6 Cleaning 8 Compliance WEEE 29 Connections SFP TPA to DUT 6 SMA 6 7 DC Blocks 4 10 11 Electrical Specifications 19 Electrostatic Discharge Information ESD 9 ESD protection 9 ESD Sensitivity 7 Figures Cable Connectors 13 15 SFP TPA HCB P Switch Module 14 SFP TPA HCB P Switch Module Schematic 14 SFP TPA MCB R Switch Module 16 SFP TPA MCB R Switch Module Schematic 16 The SFP HCB Test Adapter Plug 3 The SFP MCB Test Adapter Receptacle 4 Glossary 30 Handling and Storage 8 Low Speed Connector 4 Low Speed Connector Part Numbers 4 Making Con
9. HCB TPA without Connector and Pad Insertion Loss db at 5 GHz 0 56 0 36 MCB TPA without Connector and Pad Insertion Loss db at 5 GHz 2 2 1 83 1 64 iaai HES Sn NICE TERS ey Connectors and Return Loss GHz at 20 db 33 Mated HCB and MCB TPAs with Connectors and Pads Differential Impedance ohms 90 110 All Differential Pairs Receptacle and Plug 34 ps Rise Time 20 80 excluding SFP connector Differential Impedance ohms 30 120 All Differential Pairs Receptacle and Plug 34 ps Rise Time 20 80 including SFP connector Impedance ohms 34 ps Rise 45 55 Single ended signals within differential pairs Time 20 80 Receptacle and Plug excluding SFP connector Intra pair Skew ps 6 6 All Differential Pairs Receptacle and Plug Inter pair Skew ps 6 6 All Differential Pairs Receptacle and Plug Single aggressor with SFP connector mated NEXT db at 5 GHz 45 HCB to MCB with standard coaxial cables and terminations Page 19 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Table 6 Electrical Specifications Optional External DC Block as Supplied by Wilder Technologies SPECIFICATION MIN TYP MAX NOTES Insertion Loss db at 100 kHz 12 4 GHz 0 50 at 12 4 26 5 GHz 0 75 VSWR 7kHz TO 26 5 GHz 1 35 Upper 3db Bandwidth GHz 26 5 Lower 3db Bandwidth kHz 7 100 Voltage Volts Max In Line Capacitance
10. Hz jii SDD21 20 00 SDD21 2 SDD21 10 00 0 00 1 X IY 10 00 1y 2x 2Y 20 00 2Y 30 00 40 00 50 00 60 00 70 00 80 00 18000 00 MHz 4000 00 MHz 70 52 dB 69 70 dB 8000 00 MHz 61 91 dB 67 47 dB Figure 18 Typical Differential NEXT with mated connectors adjacent differential pairs both transmit and receive terminated at both ends L SDD21 20 00 SDD21 2 SDD21 10 00 0 00 1X ga 10 00 bad 2x 2Y 20 00 zY 30 00 40 00 50 00 60 00 W 70 00 80 00 10 00 MHz Step 10 00 MHz 1799 00 MHz 18000 00 MHz 4000 00 MHz 66 11 dB 65 69 dB 8000 00 MHz 61 38 dB 59 83 dB Figure 19 Typical Differential FEXT with mated connectors adjacent differential pairs both transmit and receive terminated at both ends Page 26 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Wilder Technologies LLC Limited Warranty Wilder Technologies LLC warrants that each Test Adapter 1 is free from defects in materials and workmanship and 2 conforms to Wilder Technologies specifications for a period of 12 months See Consumable and Fragile Material Warranty for exceptions to the 12 month warranty The warranty period for a Test Adapter is a specified fixed period commencing on the date of ship from Wilder Technologies LLC If you did not purchase your Test Adapter directly from W
11. P TPA MCB R Switch Module is ESD Sensitive The SFP TPA MCB R Switch Module assembly incorporates electrostatic sensitive components Additionally when an active DUT is installed that device also becomes susceptible to ESD Observe proper ESD precautions further discussed later in this document Page 7 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual General Test Adapter Cable and Connector Observing simple precautions can ensure accurate and reliable measurements Handling and Storage Before each use of the SFP TPA ensure that all connectors are clean Handle all cables carefully and store the SFP TPA in the foam lined instrument case when not in use if possible Do not set connectors contact end down Install the SMA protective end caps when the SFP TPA is not in use Visual Inspection Be sure to inspect all cables carefully before making a connection Inspect all cables for metal particles scratches deformed threads dents or bent broken or misaligned center conductors Do not use damaged cables Cleaning If necessary clean the connectors using low pressure less than 60 PSI compressed air or nitrogen with an effective oil vapor filter and condensation trap Clean the cable threads if necessary using a lint free swab or cleaning cloth moistened with isopropyl alcohol Always completely dry a connector before use Do not use abrasives to clean the conne
12. SDD21 0 00 1 00 5000 00 MHz 0 98 dB ioe 0 80 dB 1 77 dB 11100 00 MHz 3 00 1 80 dB 1 41 dB 3 11 dB 15000 00 MHz site 2 24 dB 1 69 dB 4 00 dB 5 00 6 00 rn a 7 00 8 00 9 00 i i 3 100 00 MHz Step 100 00 MHz 1790 00 MHz 18000 00 MHz Figure 12 Available S4Ps showing balanced insertion loss of HCB without connector MCB without connector and HCB Through MCB without connectors Page 22 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual 10 00 dB SDD1 1 50 00 sDD11 2 SDD11 40 00 30 00 i 1x 3276 95 MHz il i 1Y 20 25 dB 2009 A H y 20 72 dB 2X 16584 32 MHz H 2Y 9 90 dB 10 00 2Y 10 47 dB 0 00 H H t ji F F rt 10 00 20 00 30 00 40 00 10 00 MHz Step 10 00 MHz 1799 00 MHz 18000 00 MHz Figure 13 Typical mated pair balanced return loss 10 00 dB S D D 1 1 50 00 l spp11 i i j 2 SDD11 3 SDD11 40 00 30 00 1X 2000 00 Mhz 20 00 f i i R erie 1Y 26 64dB 2X 5000 00 MHz 10 00 i 2Y 3051dB i 2Y 2658 dB 2Y 286248 P S nn E E T 3Y 23 68 dB 3Y 3259dB 10 00 20 00 A i ut ey Rani A tl if iN Mule ji yi poi PA H 40 00 li ii i Ky 0 00 100 00 MHz Step 100 00 u EIEI 18000 00 MHz Figure 14 Available S4Ps showing balanced return loss of HCB withou
13. SEP Test Adapter User Manual SFP Test Adapter User Manual Table of Contents WAEROCU CLIO orite ceases Sea deve Todos sds eta Deda iv L A ened Deis 3 Product Inspection iaee a sheabevs eelbeeseedeadebe E E a E LE settle elias R 5 The SFP Test Adapter Care and Handling Precautions ccccccccsssssececessssesseaeeeeecesesseaeeeeeeeseeeees 6 General Test Adapter Cable and CONNECtOM cccsessscccecesessnneceeececeseesssaeececesseaaeseeeeeeesssaaaeeeeess 8 Handling and Storag Eseese des ceciuesceeievvavensiedstdeageasavedben ce AAEE AN EN E EKAR CELLE EEEE ENDERR 8 Visual IIS DE CLIO eria a E a e a E 8 cleanin E sia iaaa EE EEE E a E a E E 8 Making Cone ctiOnsvscs cdccaveicsceees vgs asni a a aaa EEO veda ENEE 8 Electrostatic Discharge INfOrmatiOn ccccccccssssssccececesseseseceeeeeceseaaaesececssessesaeaesescessesneaeeeeeesensegs 9 DET Lo E EAE E E E EEEE E E iauscipesheeinen ts 10 Mechanical and Environmental Specifications ccccesssscccceceseesscececeeecessaeseeeeesessessaeeeeeesensees 13 Electrical SpecifiCatiOnsi e202 score cecersevanctunt cestestessengea seatcesdeadtegatueaneels doneetssndavecechersexsstbanaceadeegegeess 19 Wilder Technologies LLC Limited Warranty cccccccccssssccecseessesseceeeeecesesseaeeeeeesseeseseaeeeeeeses 27 Wilder Technologies LLC Terms amp Conditions of Sale cccccccecssssssecececessesssaeceeeessessneaeeeeeens 28 Compliance with Environmental
14. ach unused signal RF terminators are optionally offered by Wilder Technologies HCB Switch Module Physical Links Under Test a SFP Host Under Test Laboratory SFP TPA HCB P Sourced Signal Block Laboratory Load Page 11 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The third example shows two SFP TPA MCB TPAs R s used for testing a SFP cable Physical Links Under Test Mated Connectors SFP TPA MCB R MCB Switch Laboratory Module Sourced Signal Load MCB Switch Module SFP TPA MCB R Mated Connectors Physical Links Under Test Page 12 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Mechanical and Environmental Specifications NOTE All specifications in this manual are subject to change Table 1 General Specifications ITEM DESCRIPTION Plug Test Adapter Length w standard cables ARHAR alng H 2 mm ei ENAMEL ESS 2B inches Characteristic Receptacle Test Adapter Length w std cables 372 53 mam 2 mm 14 67 inches 08 inches Characteristic Operating Temperature 0 C to 55 C 32 F to 131 F Characteristic Storage Temperature 40 C to 70 C 40 F to 158 F Characteristic SFP TPA HCB P and SFP TPA MCB R Cable Pinout The SFP TPA cables provide four SMA connectors one lane of primary di
15. and or how to package the product for return Page 5 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The SFP Test Adapter Care and Handling Precautions The SFP Test Adapter requires careful handling to avoid damage Improper handling techniques or using too small a cable bend radius can damage the coaxial cable connections within the adapter housing or the cables themselves This can occur at any point along the cable To achieve optimum performance and to prolong the SFP TPA s life observe the following handling precautions CAUTION 1 Avoid Torque Forces Twisting While individual coaxial cables within the test adapter have some rotational freedom twisting the SFP TPA as a unit with one end held stationary may damage or severely degrade performance Adherence to Caution 5 below helps to avoid twisting CAUTION 2 Avoid Sharp Cable Bends Never bend coaxial cables into a radius of 26 mm 1 inch or less Never bend cables greater than 90 Single or multiple cable bends must be kept within this limit Bending the SFP TPA cables less than a 26mm 1 Inch radius will permanently damage or severely degrade test adapter performance CAUTION 3 Avoid Cable Tension Pull Forces Never apply tension pull forces to an individual coaxial cable that is greater than 2 3 kg 5 lbs To avoid applying tension always place accessories and equipment on a surface that all
16. ctors Re inspect connectors making sure no particles or residue remains Making Connections Before making any connections review the Care and Handling Precautions section Follow these guidelines when making connections e Align cables carefully e Make preliminary connection lightly e To tighten turn connector nut only e Do not apply bending force to cable e Do not over tighten preliminary connections e Do not twist or screw in cables e Use a torque wrench and do not tighten past the break point of the torque wrench Page 8 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Electrostatic Discharge Information Protection against electrostatic discharge ESD is essential while connecting inspecting or cleaning the SFP TPA test adapter and connectors attached to a static sensitive circuit such as those found in test sets Electrostatic discharge can damage or destroy electronic components Be sure to perform all work on electronic assemblies at a static safe work station using two types of ESD protection e Conductive table mat and wrist strap combination e Conductive floor mat and heel strap combination When used together both of these types provide a significant level of ESD protection Used alone the table mat and wrist strap combination provide adequate ESD protection To ensure user Safety the static safe accessories must provide at least 1
17. facturer or dealer of the goods and or services offered herein and that the prices offered do not exceed those charged to any customer for like quantities services or materials under the same conditions Page 28 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Compliance with Environmental Legislation Wilder Technologies LLC is dedicated to complying with the requirements of all applicable environmental legislation and regulations including appropriate recycling and or disposal of our products WEEE Compliance Statement The European Union adopted Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE with requirements that went into effect August 13 2005 WEEE is intended to reduce the disposal of waste from electrical and electronic equipment by establishing guidelines for prevention reuse recycling and recovery Wilder Technologies has practices and processes in place to conform to the requirements in this important Directive In support of our environmental goals effective January 1 2009 Wilder Technologies LLC has partnered with E Tech Recycling of Beaverton Oregon www etechrecycling com to recycle our obsolete and electronic waste in accordance with the European Union Directive 2002 96 EC on waste electrical and electronic equipment WEEE Directive As a service to our customers Wilder Technologies is also available for managing the p
18. fferential TX and RX Labels clearly mark each cable or connector The following figure refers to the pin description table for the plug connector Low Speed Connector See Table 3 amp 4 lt 4SMAs for Pin 1 End Ref High Speed Testing SFP Plug Connector s See Table 4 Color ID for Data Line Polarity Color ID for See Table 4 Differential Pair See Table 2 amp 4 Figure 3 Cable Connectors SFP TPA HCB P shown Page 13 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual The following figure refers to the SFP TPA HCB P Switch Module assembly Refer to SFF 8431 for test details and settings of the Switch Module assembly Note The default settings for switch S1 are Pin 1 Off Pin 2 Off Pin 3 Off Pin 4 NC The mating 3 position receptacle connector housings and contact receptacles for 22 30awg wire are provided with each SFP TPA HCB P Switch Module assembly allowing the user to create custom Switch Module cables Molex part number 22 01 2035 for the housings and 08 55 0102 for the receptacle contacts Replacement plug parts can be purchased through Molex distributors TX_FLT S1 1 Switch Off RX_LOS S1 3 wr Ae Switch Off VECT 6 Xe Tx_DIS RSO RST 1 8 OOo Figure 4 SFP TPA HCB P Switch Module M_ABS S1 2 Switch Off Figure 5 SFP TPA HCB P Switch Module Schematic Page 14 2011 2012 2
19. ilder Technologies LLC the serial number and a valid proof of purchase will be required to establish your purchase date If you do not have a valid proof of purchase the warranty period will be measured from the date of ship from Wilder Technologies LLC If during the warranty period the Test Adapter is not in good working order Wilder Technologies LLC will at its option repair or replace it at no additional charge except as is set forth below In some cases the replacement Test Adapter may not be new and may have been previously installed Regardless of the Test Adapter s production status Wilder Technologies LLC appropriate warranty terms apply Consumable and Fragile Material Warranty Wilder Technologies LLC warrants that consumable materials and all fragile materials supplied by Wilder Technologies LLC either as part of an instrument or system or supplied separately will be free from defects in material and workmanship at the time of shipment Extent of Warranty The warranty does not cover the repair or exchange of a Test Adapter resulting from misuse accident modification unsuitable physical or operating environment improper maintenance by you or failure caused by a product for which Wilder Technologies LLC is not responsible The warranty is voided by removal or alteration of Test Adapter or parts identification labels The initial three months are unconditional the remaining months excludes plugs receptacles and SMA c
20. nections 8 Mechanical and Environmental Specifications 13 Molex part numbers 4 Product Inspection 5 Product Return 5 Pull Force 6 7 RF Terminations 3 4 10 11 Secure Storage 5 SFF Specification 3 14 16 SFP TPA HCB P Cable Pinout 13 SFP TPA HCB P Plug TPA Testing a Host 11 SFP TPA MCB R Testing a SFP Module 10 SFP TPA MCB R Cable Pinout 13 SFP TPA MCB R s Testing a SFP Cable 12 SMA cables 13 Support 28 Supporting Instrument Cables or Accessories 7 Tables Electrical Specifications External DC Block 20 Electrical Specifications RF Termination 20 Electrical Specifications TPA 19 General Specifications 13 SFP Plug amp Recept Pin Assignments 18 SFP TPA 12 Position Cable Connector 17 SMA Cable Connectors High Speed 17 Terms and Conditions of Sale 28 User Model Examples 10 11 12 Visual Inspection 8 Warranty 27 Web Sites support wilder tech com 27 28 www etechrecycling com 29 www wilder tech com 27 WEEE 29 Page 31 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D Visit our website at www wilder tech com Vrms WILDER TECHNOLOGIES It s all about integrity Wilder Technologies LLC 6101A East 18 Street Vancouver WA 98661 Phone 360 859 3041 Fax 360 859 3105 www wilder tech com 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D Created 10 24 2011 Updated 2 6 2013
21. onnectors Connectors are wear items and excluded from the warranty after the initial three months These warranties are your exclusive warranties and replace all other warranties or conditions express or implied including but not limited to the implied warranties or conditions or merchantability and fitness for a particular purpose These warranties give you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction Some jurisdictions do not allow the exclusion or limitation of express or implied warranties so the above exclusion or limitation may not apply to you In that event such warranties are limited in duration to the warranty period No warranties apply after that period Items Not Covered by Warranty Wilder Technologies LLC does not warrant uninterrupted or error free operation of a Test Adapter Any technical or other support provided for a Test Adapter under warranty such as assistance via telephone with how to questions and those regarding Test Adapter set up and installation will be provided WITHOUT WARRANTIES OF ANY KIND Warranty Service Warranty service may be obtained from Wilder Technologies LLC by returning a Wilder Technologies LLC Returns Material Authorization and the Test Adapter to Wilder Technologies LLC during the warranty period To obtain RMA number contact support wilder tech com You may be required to present proof of purchase or other similar proof of wa
22. ows adjustment to eliminate tension on the SFP TPA and cables Use adjustable elevation stands or apparatus to accurately place and support the SFP TPA CAUTION 4 Connect the SFP TPA First To prevent twisting bending or applying tension to the coaxial cables when connecting a SFP TPA always attach the SFP TPA to the device under test DUT or cable under test before attaching any SMA connectors Carefully align the SFP connectors and then gently push the connectors together until fully seated If the SFP TPA must be turned or twisted to make connection to the DUT avoid using the SFP TPA housing alone to make this occur Try to distribute the torque forces along the length of the test setup and cabling If this is not possible it is recommended to first loosen or disconnect the SMA connections at the SFP TPA make the connection to the DUT and then re tighten or attach the test equipment leads NOTE Only grip the test adapter housing when inserting or extracting the SFP TPA to or from the DUT Pulling directly on the SFP TPA cables or using them to insert the SFP TPA may cause damage CAUTION 5 Carefully Make SMA Connections To connect the SFP TPA SMA connectors follow these steps 1 Hold the cable stationary by grasping the cable at the black heat shrink section near the SMA connector 2 Insert the mating SMA barrel and hand tighten the free spinning SMA nut onto the connector while avoiding pulling bending or
23. ponsibility Loss or damage that occurs during shipping by a carrier selected by you is your responsibility You must notify Wilder Technologies LLC within 7 days of the date of your invoice or acknowledgement if you believe any part of your purchase is missing wrong or damaged Unless you provide Wilder Technologies LLC with a valid and correct tax exemption certificate applicable to your purchase of Product and the Product ship to location you are responsible for sales and other taxes associated with the order Shipping dates are estimates only WARRANTY WILDER TECHNOLOGIES LLC warrants that the item s manufactured under the Buyer s contract shall be free from defects in materials and workmanship furnished by WILDER TECHNOLOGIES LLC and shall conform to the applicable drawings and specifications WILDER TECHNOLOGIES LLC S liability herein for breach of warranty contract or negligence in manufacturing shall be limited to repair or replacement Repair or replacement of defective items will be applicable only if the Buyer notifies WILDER TECHNOLOGIES LLC by written notice within 30 days of delivery All claims shall be addressed to support wilder tech com or WILDER TECHNOLOGIES LLC 6101A East 18th Street Vancouver Washington 98661 U S A ATTENTION Customer Service Manager WILDER TECHNOLOGIES LLC reserves the right to inspect at the Buyer s plant all items claimed to be defective or nonconforming prior to authorizing their return WIL
24. roper recycling and or disposal of all Wilder Technologies products that have reached the end of their useful life For further information and return instructions contact support wilder tech com Page 29 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Glossary of Terms TERMINOLOGY DEFINITION Aggressor A signal imposed on a system i e cable assembly to measure response on other signal carriers Decibel dB Ten times the common logarithm i e log10 of the ratio of relative powers Far end crosstalk or FEXT Crosstalk that is propagated in a disturbed channel in the same direction as the propagation of a signal in the aggressor channel The terminals of the aggressor channel and the victim channel are usually close to each other Informative The designation of a test that is not required for compliance Insertion loss The ratio expressed in dB of incident power to delivered power Near end crosstalk or NEXT Crosstalk that is propagated in a disturbed channel in the opposite direction as the propagation of a signal in the aggressor channel The terminals of the aggressor channel and the victim channel are usually close to each other Normative The designation of a test that is required for compliance Return Loss The ratio expressed in dB of incident power to reflected power SFP Enhanced Small
25. rranty entitlement You are responsible for any associated transportation charges duties and insurance between you and Wilder Technologies LLC In all instances you must ship Test Adapters in Wilder Technologies LLC approved packaging Information on packaging guidelines can be found at www wilder tech com Wilder Technologies LLC will ship repaired or replacement Test Adapter Delivery Duty Prepaid DDP and will pay for return shipment You will receive title to the repaired or replacement Test Adapter and you will be the importer of record Page 27 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Wilder Technologies LLC Terms amp Conditions of Sale Other Documents This Agreement may NOT be altered supplemented or amended by the use of any other document s unless otherwise agreed to in a written agreement signed by both you and Wilder Technologies LLC If you do not receive an invoice or acknowledgement in the mail via e mail or with your Product information about your purchase may be obtained at support wilder tech com or by contacting your sales representative Payment Terms Orders Quotes Interest Terms of payment are within Wilder Technologies LLC s sole discretion and unless otherwise agreed to by Wilder Technologies LLC payment must be received by Wilder Technologies LLC prior to Wilder Technologies LLC s acceptance of an order Payment for the produc
26. t connector MCB without connector and HCB through MCB without connectors Page 23 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual MOTE 1 of 1 gy 100 mV div 55 100 mv div 55100 mV div 49100 m div ire R Figure 15 Typical differential TDR of SFP TPA HCB P connected to SFP TPA MCB R at 34ps Rise Time 20 80 Measured at 50 ps 10 90 Page 24 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual i SCC11 50 00 sccit 2 SCC11 40 00 i 30 00 Hopo T i 1X 2500 00 MHz 1 6 36 dB ade i tY 6 70 dB 2X 4017 46 MHz f ag 4 89 dB 10 00 TE 2y 4 72 dB 0 00 JE 10 00 20 00 30 00 40 00 50 00 10 00 MHz Step 10 00 MHz 1799 00 MHz 18000 00 MHz Figure 16 Typical mated pair common mode return loss 10 00 dB S C D2 1 20 00 scp21 2 SCD21 10 00 0 00 T m J T 1 1X 5500 00 MHz 1 32 86 dB sey tY 32 95 dB 20 00 T j T 30 00 40 00 50 00 70 00 80 00 10 00 MHz Step 10 00 MHz 1799 00 MHz 18000 00 MHz Figure 17 Typical mated pair differential to common mode conversion Page 25 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual 10 00 MHz Step 10 00 MHz 1799 00 M
27. the plug TPA and Molex part number 43645 1200 for the 12 position housing and 43030 011 for the receptacle contacts used with the receptacle TPA Replacement parts can be purchased through Molex distributors NOTE The receiver SMA connections for SFP are normally AC coupled The SFP plug and receptacle TPAs do NOT have internal DC Blocks This allows for parametric testing through the TPAs Normal testing may require DC Blocks May be optionally ordered from Wilder Technologies Refer to the Electrical Specifications section of this document for DC Block performance parameters Page 4 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual Product Inspection Upon receiving the SFP TPA from Wilder Technologies perform the following product inspection Inspect the outer shipping container foam lined instrument case and product for damage Retain the outer cardboard shipping container until the contents of the shipment have been inspected for completeness and the product has been checked mechanically and electrically Use the foam lined instrument case for secure storage of the Wilder Technologies SFP Test Adapter when not in use Locate the shipping list and verify that all items ordered were received In the unlikely event that the product is defective or incomplete the Limited Warranty section discusses how to contact Wilder Technologies for technical assistance
28. ts will be made by credit card wire transfer or some other prearranged payment method unless credit terms have been agreed to by Wilder Technologies LLC Invoices are due and payable within the time period noted on your invoice measured from the date of the invoice Wilder Technologies LLC may invoice parts of an order separately Your order is subject to cancellation by Wilder Technologies LLC in Wilder Technologies LLC s sole discretion Unless you and Wilder Technologies LLC have agreed to a different discount Wilder Technologies LLC s standard pricing policy for Wilder Technologies LLC branded systems which includes hardware software and services in one discounted price allocates the discount off list price applicable to the service portion of the system to be equal to the overall calculated percentage discount off list price on the entire system Wilder Technologies LLC is not responsible for pricing typographical or other errors in any offer by Wilder Technologies LLC and reserves the right to cancel any orders resulting from such errors Shipping Charges Taxes Title Risk of Loss Shipping handling duties and tariffs are additional unless otherwise expressly indicated at the time of sale Title to products passes from Wilder Technologies LLC to Customer on shipment from Wilder Technologies LLC s facility Loss or damage that occurs during shipping by a carrier selected by Wilder Technologies LLC is Wilder Technologies LLC s res
29. twisting the SFP TPA coaxial cable Page 6 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual 3 The SFP TPA SMA connectors have flats that accept an open end 5 16 inch wrench When attaching instrument cables to the SFP TPA it is recommended that the SFP TPA SMA connectors be mechanically held and the test leads be tightened to the equipment manufacturer s torque recommendations normally 5 in lbs using a 5 16 inch open end wrench If the test set up requires repositioning first loosen or disconnect the SMA connections to avoid twisting bending or tension NOTE A drop in signal amplitude by half or 6db during the testing of a channel may indicate that a cable has been mechanically pulled free of coaxial cable connections internal to the assembly This could be determined by checking if the cable has any lateral play relative to the TPA This would only occur when the TPA has exceeded the pull force as specified within the mechanical specification If the cable cannot be re seated the test adapter will need to be sent back to the factory for service e CAUTION 6 Independently Support Instrument Cables or Accessories Excessive weight from instrument cables and or accessories connected to the SFP TPA can cause damage or affect the test adapter performance Be sure to provide appropriate means to support and stabilize all test set up components e CAUTION 7 The SF
30. uF 0 474 Impedance Ohms 50 Table 7 Electrical Specifications Optional RF Termination as Supplied by Wilder Technologies SPECIFICATION MIN TYP MAX NOTES VSWR DC to 4 GHz 1 05 4 to 12 4 GHz 1 15 12 4 to 18 GHz 1 20 Frequency Range GHz DC 18 Power derates linearly from 100 lt 25 C to Power Dissipation Watts 2 paran al 10 125 C Impedance Ohms 50 Page 20 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual 40 mv TDD21 Bit Pattem PRBS Data Rate Gb s 10 Rise Time ps 0 Patter Length bits 2 11 1 Amplitude mV 200 440 00 400 00 0 00 40 00 0 000 ps 19 792 ps 197 917 ps Figure 9 Typical mated pair 10 Gb s eye diagram Name Measurement Result C Eveet sao C ewh omeo Eve Duty Cyde Dst oos Figure 10 Typical mated pair 10 Gb s eye data Page 21 2011 2012 2013 Wilder Technologies LLC Document No 910 0019 000 Rev D SFP Test Adapter User Manual nae SDD21 1 00 SDD21 2 SDD21 0 00 1 00 1 X 9571 27 MHz 1 7 2 94 dB io ty 3 00 dB 3 00 4 00 5 00 6 00 7 7 00 8 00 10 00 MHz Step 10 00 MHz 1799 00 MHz 18000 00 MHz Figure 11 Typical mated pair balanced insertion loss ee SDD21 1 00 SDD21 2 SDD21 3
Download Pdf Manuals
Related Search