Pro-Ject Stereo Box RS
Contents
1. 10 DEL BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Stereo Box RS Dear music lover thank you for purchasing a PRO JECT AUDIO amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 15 Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power supply is used to disconnect the unit from the mains Make sure that the power supply is easily accessible at all times Never handle the device the power supply while your hands are wet or damp V Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Tubes produce heat Proper ventilation has to be guaranteed all the time The unit must not be stacked Connectors O O 1 19 20 O O CE RoHS E Pro Ject Audio S CE Vienna Austria Make all connections whilst the amplifier is disconnected from the power supply Tak2. 3 e XX v VOLUME Stereo Box RS To switch on from standby or to standby The switch on the left hand side of the front panel turns the unit on or back into standby The blue LED above the stand by switch shows that the unit is switched on After switching on the tubes need a short time to reach the correct operating temperature During warm up the blue LED above the stand by switch is blinking We recommend to set the volume control to 0 prior to switching on Input selector After the unit is powered on operating the switch next to the six LEDs selects the inputs The selected input will be shown by the corresponding LED Volume Adjust the volume to the desired level using the large knob on the front panel Audio Trade GmbH Pro Ject Stereo Box RS Revision 2014 2 1 3 Replacing batteries Proceed as follows e Unlock and slide open the battery case cover e Replace the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V ES Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Stereo Box RS Tubes 2 x ECC88 6922 Power output 2 x 80W 120W at 8 ohms 4 ohms both channels driven Frequency response 20Hz 50kHz 1 5dB 3dB Noise floor 90dB A weighted T
3. HD 0 1 100W Gain 31dB Pre out Out Variable RCA phono sockets gain 12db Subwoofer out Sub RCA phono socket gain 18dB Record out Out Fix RCA phono sockets gain OdB Fixed output signal Line level inputs 4 pair RCA phono sockets and 1 pair XLR sockets Input impedance 50kohms for RCA input In 1 In 5 and 20kohms XLR input In 6 Wiring XLR sockets 1 ground 2 hot and 3 cold Speaker connectors 4mm banana plugs spades connectors or naked wire Outboard power supply 48V 2 5A DC suitable for your country s mains supply Power consumption 2 5A DC lt 1W in standby Replacement battery remote control 1 x CR2032 3V or 1 x CR2025 3V Dimensions W x H x D D with sockets 206 x 72 x 200 210 mm Weight 2650g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions nies for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawtul rights of the customer Copyright PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to press The manufacturer re
4. e care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white y The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Only connect one loudspeaker with an impedance not less than 4 ohms per channel Wiring XLR sockets 1 ground 2 hot and 3 cold Never use any other power supply than the one supplied with the unit Variable Inputs Line level sources such as a CD player or a tuner can be connected to the input sockets marked IN 1 IN 6 Subwoofer output An active subwoofer may be connected to the output sockets marked Sub Pre Out A power amplifier or active loudspeakers can be connected to the output sockets marked Out Variable 2 Audio Trade GmbH Pro Ject Stereo Box RS Revision 2014 2 1 Record output connecting a headphone amplifier Out Fix connects an analogue record device ore a Pro Ject Head Box headphone amplifier 5 Out Fix provides a fixed output level Mains power connection Connect the low voltage plug from the power supply to the 2x48V socket of the amplifier before connecting the power supply to the mains S turns the unit on or back into standby and adjust the sound volume Gar and Y select the inputs Remote control ON OFF Front panel controls o A 2 gt 2
5. serves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyright 2014 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 4 Audio Trade GmbH Pro Ject Stereo Box RS Revision 2014 2 1
Download Pdf Manuals
Related Search