SF8174(V) Quick Installation Guide
Contents
1. X VIVOTEK SF8174 REER re Quick Inetallanon O lj English F 1 A838 I Fran ais Espa ol Deutsch Portugu s Italiano T rk e Polski Pycckw Cesky Svenska Nederlands Dansk I Indonesia 443 yall 5MP e 360 Surround View PoE SUPREME r r Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected Do not place the Network Camera on unsteady surfaces oO Do not insert sharp or tiny objects into the Network Camera J Package Contents O SF8174 Quick Installation Guide Refer to your user s manual for the operating temperature Do not touch the Network Camera during a lightning storm Do not drop the Network Camera Screws Anchors Cable tie Power amp I O Cables P L N EN 1 English Physical Description Inner View Lens Contacts for Internal Microphone B Spring Contacts A Ethernet 10 100 RJ45 Socket Header J7 Cabling Cutout Status LEDs Outer View Reset Button MicroSD SDHC SDXC Card Slot Dome cover Built in Microphone A IMPORTANT Record the MAC address under the camera base before installing the camera EN 2 E j Hardware Installation First open the dome cover by pressing the release button You may squeeze the opposite edge of the dome c2. if serial numbers have been altered defaced or removed Further consequential and incidental damages are not recoverable under this warranty What VIVOTEK Will Do VIVOTEK will in our sole discretion repair or replace any product that proves to be defective in material or workmanship Any repair or replaced part of the product will receive a THREE MONTH warranty extension How To Get Service Contact our authorized distributors in your region Please check our website www vivotek com for the information of an authorized distributor near you Your Rights SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE VIVOTEK INC 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan www vivotek com 1 Proof of the date of purchase is required In the event you can not render such document warranty will commence from the date of manufacture 2 Cosmetic damage will only be covered by this warranty if such damage has been existed at the time of purchase AR 184 P N 625024300G Rev 1 0 All specifications are subject to change without notice Copyright 2014 VIVOTEK INC All rights reserved VIVOTEK INC VIVOTEK USA INC 6F No 192 Lien Cheng Rd Chung Ho New Taipei City 235 Taiwan R O C
3. program The program will search for VIVOTEK Video Receivers Video Servers and Network Cameras on the same LAN 4 After a brief search the main installer window will pop up Double click on the MAC address that matches the one printed on the camera label or the serial number on the package box label to open a browser management session with the Network Camera N gt Ready to Use A browser session with the Network Camera should prompt as shown below viverex Mega Pixel Network Camera ee P jo i SITE See Stee Loe lt 2 Refer to the Panoramic PTZ Installation Guide in your product CD for the rest of the configuration details o NOTE If you encounter problems with displaying live view or the onscreen plug in control you may try to manually remove the plug ins that might have been installed on your computer Remove the following folder C Program Files x86 Camera Stream Controller EN 10 HARDWARE LIMITED WARRANTY What Is Covered This warranty covers any hardware defects in materials or workmanship with the exceptions stated below How Long Coverage Lasts This warranty lasts for TWENTY FOUR MONTHS from the date of purchase by the original end user customer What Is Not Covered This warranty does not cover cosmetic damage or any other damage or defect caused by abuse misuse neglect use in violation of instructions repair by an unauthorized third party or an act of God Also
4. the Panoramic PTZ Installation Guide in your product CD for design considerations before you proceed with physical installation Attach Camera to Mounting Adaptor An adapter bracket AM 517 is required 1 Align the bracket s screw slots with mounting holes on the AM 51A 2 Secure the bracket to AM 51A using 2 pan head M2 6 screws 3 Align the camera s screw slots with the C holes 4 Use the included M2 6 screws to secure camera to bracket Ceiling Mount Installation Install the Pendant Pipe Below is a sample procedure using a pendant pipe 1 Determine a hard surface ceiling location and use the four mounting X x 473 mm holes on the pendant head to mark 9 the positions where holes will be drilled to secure the pendant head Note that screws are user supplied and they should be at least 11mm long AM 117 2 Route cables through the pendant pipe and the pendant head AN SIA 41mm L EN 5 English Install to the Ceiling _ 2 3 4 5 6 Drill pilot holes into the ceiling Then hammer four anchors into the holes Secure the pendant head to the ceiling using four screws Connect the two white header connectors to the J6 and J7 connectors Connect the Ethernet cable to the RJ 45 socket You will find a desiccant bag attached to the camera Replace the desiccant bag included in the camera with the one shipped within the accessory bag Attac
5. 2050 Ringwood Avenue San Jose CA 95131 T 886 2 82455282 F 886 2 82455532 E sales vivotek com T 408 773 8686 F 408 773 8298 E salesusa vivotek com VIVOTEK Netherlands B V Busplein 36 1315KV Almere The Netherlands T 31 0 36 5389 149 F 31 0 36 5389 111 E saleseurope vivotek com
6. h the dome cover to the camera 7 Route cables through a 3 4 conduit from the pendant head Header J6 30 100cm NOTE Arrange the cables neatly to avoid getting in the way when the dome cover is attached EN 6 Wall Mount Bracket Installation Below is a sample procedure using a wall mount bracket and a pendant pipe 1 Determine a hard surface ceiling location Use the four mounting holes on the wall mount bracket to mark the positions where holes will be drilled to secure the bracket and routing cables Note that screws are user supplied and they should be at least 11mm long 2 Feed cables through the bracket 3 Install the pendant pipe 4 Install the camera to the mounting adapter See Attach Camera to Mounting Adapter on the previous page 5 Install the mounting adapter to pendant pipe 6 Tighten the connection using the included hex wrench AN SIA gt 9 EN 7 English 7 Install the speed dome camera next to the fisheye with their lens positioned at approximately the same height For details about speed dome installation please refer to its documentation 8 Connect all cabling including the IO cables to J6 and J7 and the Ethernet cable to RJ 45 connector 9 Install the dome cover ff NOTE E Network Deployment 5 If DC power is preferred it should comply with O P 12VDC 1 5Amin L P S pe
7. over if the dome cover does not come off easily Then follow the steps below to install the camera to either a ceiling or a wall Slide cover Release button If you plan to route cables from the side of camera remove the rubber slide cover from the dome cover Connecting Ethernet Cable amp the Power and IO Cable Connect the supplied power amp IO cables if your switch does not support PoE Connect the white header connectors to J6 and J7 on the camera Power amp IO Cable EN 3 English Connecting Cables If you need to route cables through the side opening proceed with the following 1 Connect the Ethernet and the Power amp IO cables The Ethernet cable is user supplied 2 Use an included cable tie to secure the Ethernet and IO cable to the base plate Insert the cable tie through the vertical mounting tab located on the edge of the cabling cutout 3 Make a clearance between cables and the vertical mounting tab Arrange the cables neatly to avoid getting in the way when the dome cover is attached 4 Cut the extra length from the cable tie If you route cables through a drill hole on a wall ceiling simply route cables through the cabling cutout Make a clearance between cables and the vertical tab Ethernet Power and IO cables It is recommended to remove the strain relief boot if your Ethernet cable Strain relief boot Comes with one EN 4 IMPORTANT Refer to
8. r IEC 60950 1 General Connection without PoE 1 Connect RJ45 Ethernet cable to a switch 2 Connect the power cable from the Network Camera to a power outlet 3 If you have external devices such as sensors and alarms make the connection from the general I O terminal block s 3V3 Power 3 3V DC D DO Digital Output D I Digital Input GND Ground General I O Terminal Block Power Cord Socket Black 1 Microphone In Pink Audio Out Green EN 8 Power over Ethernet PoE When using a PoE enabled switch The Network Camera is PoE compliant allowing transmission of power and data via a single Ethernet cable Follow the below illustration to connect the Network Camera to a PoE enabled switch via Ethernet cable FA NOTE 1 This equipment is only to be connected to PoE networks without routing to outside plants 2 For PoE input connection use only UL listed I T E with PoE output PoE Switch When using a non PoE switch Use a PoE power injector optional to connect between the Network Camera and a non PoE switch PoE Power Injector optional Non PoE Switch EN 9 English Assigning an IP Address Install Installation Wizard 2 from the Software Utility directory on the software CD The program will conduct an analysis of your network environment After your network is analyzed please click on the Next button to continue the
Download Pdf Manuals
Related Search