FA-PAC(PC)M4D
Contents
1. Power switch Screw hole M3x4 for mounting AC inlet lt Rear View gt Figure 1 Main Unit Dimensions Notes Keep the unit at least 20mm away from the wall so as to prevent temperature rise Please mount after the screw which has fixed a rubber foot is removed and a rubber foot is removed when it is mount CONTEC FA PAC PC M4D 5 Configuration FA PAC PC M4D consists of a mother bus with four slots and a power unit that supplies power to the bus Mother bus board Four slots DC power supply Power LED AC power supply Figure 2 System Block Diagram CNG LI Power 1 CN7 supply i gt AC Power supply Power LED Figure 3 Circuit Diagram CONTEC 6 FA PAC PC M4D A power connector for HDD and 3 5inch FDD is prepared on FA PAC PC M4D Connect HD FD power cable of annexing with CN3 on mother board and please utilize it in construction of a system n YELLOW 1 12V BLACK 2 GND BLACK 3 GND RED 4 5V YELLOW 1 12V BLACK 2 GND BLACK 3 GND RED 4 5V Figure 4 HDD FDD Power Connectors Table 1 Specifications of Power Connectors for HDD for 3 5inch FDD 8981 4P MOLEX 171822 4 AMP 8980 3 MOLEX 170204 1 AMP 2 C2. PC HELPER For ISA Bus Chassis Unit FA PAC PC M4D User s Manual CONTEC CO LTD Copyright Copyright 1998 CONTEC Co LTD ALL RIGHTS RESERVE No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC Co LTD CONTEC Co LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC Co LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document nor for results obtained by the user as a result of using this product Trademarks MS Microsoft MS DOS and Windows are trademarks of Microsoft Corporation Other brand and product names are trademarks of their respective holder Product Configuration FA PAC PC MA4D 1 HD FD Power Cable 1 User s Guide this booklet 1 Notes Check the contents to make sure that you have everything listed above If you do not have all the items please contact CONTEC Option connection cables are available from CONTEC Call for more information Since a power supply code is not annexed on this goods it needs to be prepared by user Use approved power cord for the connection to
3. agnetic field or noise Otherwise the unit or PC may malfunction It is very dangerous to use the unit with water liquid or metal inside Be careful not to let foreign objects come in the unit Do not modify the unit We shall not be responsible for any loss or damage incurred by modification Turn off the power of the unit when you mount or dismount the interface board into an expansion slot Do not let the sum of the consumption current of the board mounted into an expansion slot exceed the rated current If the unit becomes dirty wipe it softly with soft cloth soaked in water or neutral detergent Do not use volatile chemicals such as benzine or thinner because they may change the shape or color This chassis has IP20 if used in the industrial environment higher protection degree may apply additional protector shall be provided on application The power supply in this chassis is designed for overvoltage category II 2 5kV if used in industrial environment directly on mains add Precaution against overvoltage might be necessary If used in industrial environment an external overcurrent protection in both supply lines shall be provided CONTEC FA PAC PC M4D Specifications Dimensions 110 276 ew 9000000000000 0000000000000 CONTEC Power LED 190 IIIT 2 g Ss lt Front view gt cy lt Side View gt JLo Expansion slot 90000000001 000000000
4. nformity connector model 8981 4R 1 MOLEX 171826 4 AMP CONTEC FA PAC PC M4D Specifications Table 2 Specifications Specifications Number of slots Four middle size 2200 x 1220 mm Max 0 300 sow 30 sor aow 40 50 C sow electric power Power capacity DC 5V 8A DC 5V 0 3A DC 5V 6A DC 5V 0 3A DC 12V 1 5A DC 12V 1A DC 12V 1 5A DC 12V 1A 0 50 C 10 85 no condensation External dimensions 110 W x 190 H x 276 D mm 1 Input voltage range 85 250VAC 220 0 Max 122 0 Max mm Notes Power LED dose not light it and turn on and off in the case of an unmounting condition at an extension board on this unit This reason is since an output voltage is not output to fixed value by load insufficiency Please avoid to mounting on a slot of a right edge when CPU board is mounting on this unit by the condition which exceeds 40 C SIMM has shut off wind and CPU part is filled with heat The internal power supply and cooling fan FAN filter are consumables requiring replacement after use for a certain period of time Although the standards are given below their lives may be shortened depending on the operating environment The life span is likely especially to become short extremely in the place which takes influence of trash metallic powder the place which is much dust or oil corrosive gas Power supply About 5 years 25 C 60 official environment Cooling fan Ab
5. out 5 years 25 C 60 official environment Fan filter About 1 years 25 C 60 official environment A model of using power supply is LWT50H 522 Nemic Lambda Renewal parts are available from CONTEC with regard to other parts When you require one contact the selling agent or the CONTEC Information Center CONTEC FA PAC PC M4D FA PAC PC M4D User s Manual CONTEC CO LTD December 2007 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http www contec co jp English http www contec com Chinese _http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 12062007 08211998 Management No A 41 932 12062007_rev3 Parts No LZF9912
6. regular factory prices will be charged the product will be returned to you COD and no other written warranty will apply The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization Number RMA from our Sales Administration Department before returning any product No product will be accepted without an RMA number CONTEC FA PAC PC M4D 3 Cautions Note the following when handling this unit When you turn off the power switch wait at least for five seconds to turn it on again Be sure to hold the plug to connect or disconnect the power cable Since the I O expansion unit is a precision device do not use or store it in a place affected by impact or vibration Also do not use or store it in a place exposed to direct sunlight extremely high humidity or dust Do not use or store the unit in a place where there is chemical vapor or any contact with chemicals The unit has ventilation slits to prevent temperature rise Do not block the ventilation slits or use the unit in a poorly ventilated place Do not use the unit near equipment that generates strong m
7. the power supply The socket outlet must be located close to the unit and be easily accessible Main power disconnecting device for the unit is the power supply cord and the main T O switch Alternatively an externed disconnecting device may be used CONTEC FA PAC PC M4D Introduction Preface Thank you very much for purchasing FA PAC PC M4D This product is an ISA bus unit for configuring the computer system in combination with the expansion board for the PC AT or its compatible Features Steel chassis is used that suits for the applicability at site There are 4 ISA bus slots Cooling fan is built in the front panel of a unit The power supply is built in a unit CONTEC 2 FA PAC PC M4D Limited One Year Warranty CONTEC Interface boards are warranted by CONTEC to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Replacement or repair will be free of charge only when this device is returned to CONTEC freight prepaid with the original invoice This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original boards The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy If replacement with a new device is needed
Download Pdf Manuals
Related Search
FA PAC(PC)M4D fapac pc m4d