NAM Programming Guide - dmp.com
Contents
1. until any entry number is displayed To store the entered program information press SND Otherwise press To Program the Second Telephone Number If 01 2appears after you have stored the information for the first phone number you re ready to enter a second phone number The 07 indicates you re ready to enter the System ID information step 1 and the 2 indicates you re programming the second phone number The phone assigns the same security and lock codes steps 7 and 8 of the NAM PDT for the second phone number and skips steps 7 and 8 Step 11 is also skipped when programming a second phone number If 01 2did not appear after programming the first phone number and you want to program a second phone number then select the second telephone option step 10 of the NAM PDT To advance correct review or store information duplicate the procedures listed above Programming Counter Motorola cellular phones contain a counter that allows programming by the above method a limited number of times Once the maximum is exceeded you ll be unable to access this programming mode Contact a Motorola Warranty Service Center to reset the counter aiD Digital Monitoring Products LT 0337 11 96 2841 E Industrial Drive Springfield MO 65802 6310 800 641 4282 Summary Editing commands for this programming method are e sequences through entry number and data fields e CLR reverts the displayed data to the previously2. If your handset has FCN press FCN 0 your 6 digit security code twice then RCL If not press CONTROL 0 your 6 digit security code twice then The display shows 07 If the attempt is unsuccessful 07 does not appear in the display the following may have occurred e If 00 appears in the display the key sequence may have been entered too slowly Pres CLR and try again e The wrong security code may have been entered e The maximum number of times your phone can be reprogrammed has been reached Contact your phone provider for possible reprogramming assistance Programming Procedures Programming for a single phone number can be quick depending on how many programmable features you want to review or change The phone ships with factory presets for each of the features Enter the information listed in the NAM PDT as you go through the steps To advance through the programming Press To correct an entry Press CLR and start again To review NAM programming Once you ve completed the programming steps review the information by repeatedly pressing Make sure the information programmed matches that on the NAM PDT Make any necessary changes To store information and exit programming mode Any time a 2 digit step number 01 to 11 appears in the left side of the display you can store all the information programmed in the phone by pressing SND to return to normal phone operation To exit programming mode without storing Press
3. NAM Programming Guide Motorola Cellular Mobile Introduction Your cellular phone contains a special memory that retains information about the phone s individual characteristics such as its assigned telephone number system identification number and other information necessary for cellular operation This special memory is known as the Number Assignment Module NAM You can program the phone after you have contacted your cellular system operator or operators for the information described below Enter the information into the NAM Programming Data Table PDT included on back before programming the NAM of your cellular telephone Follow your system operator s instructions regarding each NAM information entry Incorrect NAM entries can cause your cellular telephone to operate improperly Information Required for Programming Before programming the phone obtain the following information from your cellular service provider and enter it into the spaces provided in the NAM PDT If your unit is equipped with a second telephone number the same information must be provided by the second cellular service provider 1 System ID 5 Access Overload Class 2 Area Code 6 Initial Paging Channel 3 Phone Number 7 MIN Mark O disabled 1 enabled 4 Group ID 8 Local Use State 0 disabled 1 enabled Additionally some specific user information must be gathered and recorded into the NAM PDT before programming the telephone This information include
4. s Six digit Security Code This code allows the user to restrict his calls in certain ways and permits other advanced security measures Refer to your user s manual for further details Select any six digit code you will remember that cannot easily be compromised Three digit Unlock Code This code unlocks the telephone after it has been locked to prevent unauthorized use With many models this number can be programmed as often as you like Consult your user s manual Select any convenient 3 digit code External Speaker Bit Enter a 1 if the unit includes a separate external speaker Enter a 0 if it does not Auto Recall Enter a 0 if you do not want Super Speed Dialing Enter a 1 if you do 2nd Telephone Number Enter a 1 if your telephone is equipped for dual system operation and you want to enter a second telephone number Enter a 0 if not Failed Page Indicator available in some models Enter a 1 for an alert if an incoming call could not be completed due to insufficient signal strength The alert consists of a series of short beeps and CALL in the display Enter 0 to disable Long Tone DTMF Bit Enter a 1 if you want to increase the duration of the DTMF tones transmitted by the telephone to access low tier equipment such as answering machines Enter 0 to disable 8 Hour Timeout Bit Enter 0 if you want the phone to turn itself off after eight hours Enter 1 to disable Entering the NAM Programming Mode Press PWR ON displays
5. stored value when pressed while in any data field e exits the program without altering any information or programming in NAM This does not increment the counter e SND stores all new data entered during this programming sequence when pressed while in any entry number field and increments the counter if the telephone number is changed NAM Programming Data Table PDT Step Press Display 1st Phone No 2nd Phone No 01 01 00000 Carrier System ID No 02 111 Area Code 03 1110111 Phone Number Station Class Mark Access Overload Class Group ID Mark 000000 User Security Code 08 123 Unlock Code 09 0334 Initial Paging Channel 10 011100 Digital Monitoring Products 2841 E Industrial Drive Springfield MO 65802 6310 800 641 4282 Option Code 1 External Speaker Local Use Min Mark Auto Recall 2nd Telephone No Always Zero
Download Pdf Manuals
Related Search