eq manual all(2012.04.14)
Contents
1. Prener PC PREAMP USER S MANUAL DSP Equalizer system Onboard DSP Equalizer with Chromatic Tuner Bleat DigiQ 9 Digital Performance 1 Liquid crystal display LCD lt m ba 2 Value knob Phase button 3 LOAD button wuss MIDD faee GFX REV FLANGER 4 SAVE button ose HHMI e voL 5 TUNER on off button ce ae ee 6 SEL button A EFX TUNER Moy p T EFX button 8 Low battery LED 2 Chromatic Tuning EFX Mode b i D 7 E a oe p co 50 a 50 m 1208 z 1 am a ae zen SAVE A A ES A l a LOAD gt a Z aa BYPASS 0 Oem a y P a DELAY A A SF S ES CHORUS 232 3AA im 1208 o nA a a m a FLANGER BASS MIDD TREB FX REV TREMOLO o 10 VOL o seeec HHT LT 2 VOL _ 1 _ Specification Equalizer Input Impedance 10M Ohms Output Impedance Less than 1K Ohms Frequency Response 20Hz 20KHz Bass Control Range 12dB 100Hz Middle Control Range 12dB 900Hz Treble Control Range 12dB 10KHz Tuner Mode Auto Chromatic Indicator LCD amp 3LEDs Accuracy 0 5cents DSP Effect Mode Delay 1 130ms Delay 2 350ms Delay 3 500ms Delay 4 700ms Chorus 1 100ms Chorus 2 500ms Chorus 3 ims Chorus 4 500ms Delay Flanger 1 1s Flanger 2 500s Flanger 3 100s Flanger 4 500s Delay Tremolo 1 1s Tremolo 2 500s Tremolo 3 100s Tremolo 4 500s Delay Reverb Roo2. This product complies with the RoHS directive E INSTALLATION MANUAL 1 Cut out the hole with template Cutting Masking Template Masking 1 Contents Tape Cutting sain we Pe lt a gt ri 2 Fee OAD yn DELAY CHORUS 11 2 3 4 FLANGER TREMOLO SSM 2 Battery Pick E Box 3 Pick Up 1 Preamp 4 Clip 5 Screw 2 Tool 2 Drilling hole for pick up 4 Electric Drill 4 Router and Grinder cutting edge 3mm MES D o aaa 1 a ee 5 Round File 2 3mm or 3mm 3 Phillips Screwdriver 6 Masking Tape i i 7 Fix wire with clip 3 Insert EQ and battery box into hole of guitar 4 Fasten screws properly Battery box x Cable 5 Put plugs Battery into jacks Box Solution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens noise or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 6 Installing the pick up 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between
3. the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top of guitar is bended When the pickup is installed to only a part of the groove of saddle back page Cutti ng Template 1 Print this file without scaling option Print gt P H ling gt P ne dae ma a ec aing 2 Check the size with actual ruler W None 3 Cut out the dotted line or desire model O Fit to print margins 4 Adhere to location use double stick tape Reduce to print margins 5 Cut follow solid line use cutter 41 0mm 68 0mm Gl o O2 0mm 61 0mm E mo i m t i LO ve l i Ts _ s CO LO i ot o i 2 0mm o 7 9 amp eee Preamp Opening wenn nnn nnn nnn ene n nnn n nnn aden Battery Box Opening 1 2 3 6 7 8 9 10 11 12 13 14 15
4. ce It will delete all of the user s data and setting Before resetting please check all of the pre setting data carefully FACTORY RESET S process Press EXF button for a long time at EQ mode All of display on LCD will be disappeared Extract the jack from the preamp for 3 seconds and insert it again Then it will reset to the beginning Description of Controls VALUE Adjusting the volume in EQ mode Turn to clock wise when choosing the function Press for phase function EFX Select one of 16 digital sounds SEL Select the function BASS MID TREB EFX Level REV SAVE Function for saving the current sound LOAD Loading the current sound TUNER Tuner power on off XLR Jack 1 4 Jack Battery Sufficient with 4 pcs of 1 5V AA batterys Recommend to use alkaline battery Be careful not to insert the battery cell wrongly Caution The jack should be pluged for proper Preamp working TUNER will works regardless pluging jack There is no output sound please check if tuner or mute is turned on When LCD screen is dim or no display please check battery life To prevent battery loss please unplug jack when preamp is not in use Do not disassemble for repair Return to your dealer for service or repair Do not use too much force when operating the control belat BELCAT Co Ltd Tel 86 752 355 7545 Fax 86 752 355 2460 Email belcat belcat com Internet www belcat com ROHS X ce
5. m size Battery Life Preamp Over 60Hrs 30mA Only Tuner not connect cable 800Hrs 3 5mA 4 Setting up the Preamp for use Mode choice EQ EFX Level Reverb Level When pressing SEL button it will select BASS MID TREB EFX REV in order When the displayed light is blinking on the LCD use VALUE knob for find out proper sound If you do not choose the function more than 5 seconds with VALUE knob it will be automatically return to previous VALUE Saving 9 setting values can be saved With SAVE button you can choose one of position you like from the 1st to 9th position When SAVE on LCD is blinking you can save it on your favorite position 1 9 by pressing saving button for 5 second After completion of saving blinking SAVE on LCD will disappear Loading You can load saved value setting from 1st 9th position LOAD will be blinking when you push this button for over 5 second After completion of loading blinking LOAD on LCD will disappear Tuner Mode Press TUNER button for tuner mode and you can use auto chromatic tuner Mute function will be automatically on with tuner mode One more press will turn off tuner mode Low Battery LED will light up when the battery has lost power Replace battery when this light is on Factory Reset This function is to reset to the beginning of DigiQ 10 All of pre setting will be deleted by this function Noti
Download Pdf Manuals
Related Search