Home

HEADHUNTER10

1. Tilt 16 bit 5 0 255 Pan amp Tilt Speed fast to slow 6 0 255 Dimmer 0 100 7 0 255 Red 0 100 8 0 255 Green 0 100 9 0 255 Blue 0 100 10 0 255 White 0 100 0 35 No function 36 55 Color temperature selection White 3200K 56 75 Color temperature selection White 3400K 76 95 Color temperature selection White 4200K 96 115 Color temperature selection White 4900K 116 135 Color temperature selection White 5600K Li 136 155 Color temperature selection White 5900K 156 175 Color temperature selection White 6500K 176 195 Color temperature selection White 7200K 196 215 Color temperature selection White 8000K 216 235 Color temperature selection White 8500K 236 255 Color temperature selection White 10000K 12 0 14 No function 15 255 Color Macros 13 0 19 No function 20 255 Strobe0 20HZ 0 99 Disable Sound Control 14 100 199 Enable Sound Control 200 255 System Reset when this value is held 5 second CH Value Function 1 0 255 PAN 0 630 2 0 255 Tilt 0 220 3 0 255 Pan amp Tilt Speed from fast to slow 4 0 255 Dimmer 0 100 5 0 255 Red 0 100 6 0 255 Green 0 100 7 0 255 Blue 0 100 8 0 255 White 0 100 0 19 No function 2 20 255 Strobe 0 20HZ 5 amp IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS HEED ALL WARNINGS If after you have followed the instructions outlined above this device fails to function please contact your dealer Under no circumstances sho
2. cause severe eye damage Avoid looking directly into the light source at all times Specifications e Voltage AC100V 240V e Power Consumption 150W e Light source USA CREE 36x3W R8 G10 B10 W8 LED drive current 750mA Beam angle 8 Max output 1m 88750 lux e IP class IP20 e DMX channels 9 14 DMX Channels e Packing Dimensions 315x295x22mm e Net weight 4 9 Kg e Gross weight 6 Kg Features e 3PIN XLR DMX and out IEC power and out 4control modes DMX512 automatic programs sound control mast slave e LCD display for easy setup e Indoor operation temperature range 20 C 40 C e 2 DMX Modes 9ch 14ch e Dimmer 0 100 e Pan 630 degree e Tilt 220 degree e Temperature controlled fan cooling fan will change speed according to temperature Lens 2 Yoke Base Carrying handis 5 LCD Display Mode esc button Up button Down button 9 Enter button Power DMX 2 Auto 03 Sound Fan 15 LED Drive PCB Power in 17 Power out DMX input DMX output 2 INSTALLATION Installation requirements e The product can be hung or placed on a solid surface with the double mounting brackets e If you install the light in a hanging position always use a suitable mounting position and a clamp or screw that is strong enough to hold the product without stress Always use a safety wire to secure the light e Always keep a distance of minimum 0 5m to all obje
3. cts or persons e Installation should always be done by a trained professional e Make sure the light always has good ventilation e Itis recommended to always use 110 Ohm DMX cable to prevent data corruption of your DMX control signal Power connection The equipment has an auto switching power supply that can accommodate a wide range of input voltages The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages This equipment will accommodate between 100V and 240v AC 50 60HZ It is possible to daisy chain the power connection from one fixture to the next We recommend not connecting more than 20 fixtures on one 16A 220V socket and not more than 10 fixtures on one 16A 110V socket Color Connection PIN Brown AC live wire 1 Blue AC zero curve 2 Green Yellow AC ground wire 3 DMX serial Data Link 1 Connect the male 3pin DMX input of the first fixture to the female 3pin DMX output of the lighting controller using 110 Ohm DMX cable for example a Stagg Commandor 10 skip this step when not using a controller 2 Connect the output of the first fixture to the input of the next fixture using 110 Ohm DMX cable Repeat this process until you reach your last fixture Here it is recommended to connect a DMX terminator to the output of the last fixture in the chain ten TTT DMX add
4. ge the DMX address by pressing UP or DOWN Press ENTER to save the DMX address Control Mode Setup Control Mode Press MENU then Up or DOWN until Control Mode is displayed then press ENTER Press UP or DOWN to choose 9CH or 14CH DMX mode Press ENTER to save the Control Mode Master and Slave Modes Press MENU then Up or DOWN until Slave Mode is displayed then press ENTER Press UP or DOWN to choose Master or Slave mode Press ENTER to save the Control Mode Slave units run synchronised programs when daisy chained to the output 3pin XLR of a master unit Set the first unit as MASTER set the rest as SLAVE and use a 3pin XLR DMX cable to daisy chain the units to run automatic programs or sound controlled programs in sync Auto Mode and Sound Control setup Press MENU then Up or DOWN until Auto Sound is displayed then press ENTER Press UP or DOWN to choose Auto or Sound Press ENTER to save Pan Inverse Pan inverse setup e Press MENU then Up or DOWN until Pan Inverse is displayed then press ENTER Press UP or DOWN to choose Yes or No Press ENTER to save Tilt Inverse Tilt inverse setup Press MENU then Up or DOWN until Tilt Inverse is displayed then press ENTER Press UP or DOWN to choose Yes or No Press ENTER to save Dimming speed setup Press MENU then Up or DOWN until Dimmer Speed is displayed
5. ress 001 DMX address 001 DMX address 001 o O o O Zw 27 au de rik o I e 01 0107 ETO 1 OPERATION Control Panel Function Button Function MODE Exits from the current menu or function ENTER Enables the currently displayed menu or sets the currently selected value into the selected function UP Navigates upwards through the menu list and increases the value when in a function DOWN Navigates downwards through the menu list and reduces the value when in a function DMX 1001 Address 512 ontrol 9CH Mode U T4CH Slave Master alia stili 0 lt d ar n gt S gt U D 5 2 Inverse Yes Tilt Inverse Yes Dimmer Fast Menu H Speed Smooth Power On Power On Hours Fixture LED Temp Temp L Main A Green Auto Test Blue H White All Firmware Version System Reset Operating Instructions DMX Address DMX Address Setup Press MENU then Up or DOWN until DMX Address is displayed then press ENTER e Chan
6. staggmusic coi HEADHUNIER10 SLI MHB HH10 Table of Contents 1 BEFORE USAGE This package contains Unpacking Introduction Specifications Features 2 INSTALLATION Power Connection DMX 512 Connection 3 OPERATION Control panel Function Menu Map Operating Instructions DMX Channels 1 BEFORE USE This package contains 1 HeadHunter 10 1x Power Cable 1x User Manual Unpacking e Thank you for purchasing this product it has been thoroughly tested and has been shipped in perfect operating condition e Carefully check the packaging for damage that may have occurred during shipping e Ifthe packaging appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact e If damage has been found or parts are missing please contact your vendor or our customer support number for further instructions Introduction e This fixture can operate in four different operating modes DMX control sound active automatic or in a Master Slave configuration e This product comes with several built in programs that can be used while operating as a single unit or with multiple units linked in a master slave configuration e For best results use fog or special effects smoke to enhance the beam projection e Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture e Warning This product may
7. then press ENTER Press UP DOWN to choose between Fast linear dimming curve or Smooth logarithmic curve that simulates a halogen lamp Press ENTER to save Power On Power On Hours Lamp runtime Press MENU then Up or DOWN until Power On Hours is displayed then press ENTER e The LCD will display the total amount of runtime hours press MENU to exit LED Temp Main PCB Lamp temperature display Press MENU then Up or DOWN until Fixture Temp is displayed then press ENTER e The LCD will display the temperature of both the LED s and the Main PCB in sequence Press MENU to exit Fixture Temp Lamp Auto Test Press MENU then Up or DOWN until Auto Test is displayed then press ENTER e The light will run a test program testing all colours individually followed by all together Press MENU to exit Firmware Version Software Version Press MENU then Up or DOWN until Firmware Version is displayed then press ENTER e The LCD will show the currently installed Firmware Version Press MENU to exit System Reset System Reset Press MENU then Up or DOWN until System Reset is displayed then press ENTER The light will reset itself DMX Channels 14 CH CH Value Function 1 0 255 PAN 0 630 2 0 255 PAN 16 bit 3 0 255 Tilt 0 220 4 0 255
8. uld this device be opened Leave all servicing to qualified personnel Electrical appliances must never be used in conditions of high humidity or heat To prevent any risk of fire or electric shock never spill or splash liquids on this device Should this happen unplug the power cable from the mains outlet and switch off the mixer immediately 5 MARKING amp CONFORMITY 1 The CE mark on this product means it conforms to the EMC Directive 2004 108 CE CE marking Directive 93 68 EEC and Low Voltage Directive 2006 95 EC 2 The Crossed out Wheeled Bin is to draw your attention to the WEEE Waste Electric amp Electronic Equipment Directive 2002 96 EC It means this apparatus must be collected separately for recycling 3 RoHS compliant means this device conforms to the Directive 2002 95EC on the restriction of the use of certain hazardous substances in electrical and electronic equipments such as Mercury Lead Cadmium Hexavalent Chromium Polybrominated Buphenyl PBB and Polybrominated Diphenyl Ethers PBDE DISTRIBUTOR DEALER

HEADHUNTER10

Contents

Download Pdf Manuals

Related Search

Related Contents