OLIMEXINO-328 USER`S MANUAL
Contents
1. OLIMEXINO 328 an Arduino like development board USER S MANUAL Manual revision B November 2013 Designed by OLIMEX Ltd 2011 lead free All boards produced by Olimex LTD are ROHS compliant OLIMEXO 2013 OLIMEXINO 328 user s manual DISCLAIMER 2013 Olimex Ltd OlimexG logo and combinations thereof are registered trademarks of Olimex Ltd Other product names may be trademarks of others and the rights belong to their respective owners The information in this document is provided in connection with Olimex products No license express or implied or otherwise to any intellectual property right is granted by this document or in connection with the sale of Olimex products This work is licensed under the Creative Commons Attribution ShareAlike 3 0 Unported License To view a copy of this license visit http www creativecommons org licenses by sa 3 0 This hardware design by Olimex LTD is licensed under a Creative Commons Attribution ShareAlike 3 0 Unported License The software is released under GPL It is possible that the pictures in this manual differ from the latest revision of the board The product described in this document is subject to continuous development and improvements All particulars of the product and its use contained in this document are given by OLIMEX in good faith However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitne2. A0 A1 A2 A3 A4 SDA A5 SCL 5 3 3 CON3 DIGITAL Signal name D RXD D1 TXD D2 BUT D3 D4 D5 D6 D7 Note There is a capacitor C12 connected to D2 and in parallel to BUT for filtering bounces of the BUT but it can cause interference and unwanted filtering of signals if you want to connect for instance RF module to D2 remove C12 Page 14 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 5 3 4 CON4 DIGITAL Note that the additional pads near the CON4 seems slightly off due to the improvement of the shield design we have made Consider this alignment when referring to the white print on the board Signal name D8 D9 D10 SS D11 MOSI D12 MISO D13 SCK LED1 GND AREF 5 4 LIPO BAT connector The LIPO BAT connector comes handy when you want to use the OLIMEXINO 328 as a stand alone device Olimex LTD has a number of batteries with the proper connector They might be found here https www olimex com Products Power 5 4 mini USB connector Pin Signal name 1 5V_VBUS VCCINT USBDM 3 USBDP 4 Not connected 5 GND VCC D13 SCK LED1 D11 MOSI RESET GND Note that there is no plastic component mounted for this connector You would either need own Page 15 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual connector or jumper wires to be able to connect your AVR p
3. UBAT VIN N BATTERY CE VOUT CHARGER 2 uss pros MCP738121 420170T R GND Ms 2 2uF HC24 LRT SD5 1N4148 nini nelt t a gt A SW3 3U 5U USB_RST 22UH 18 5mA 1 e 2 DTR SDi 1N5819S DF E 1 FETA YDJ 1136 IRLHL 402 Close 9 38UDC z NAC1 ONF gt L3 SD3 CL10uH SH68 1N5819S nm 4 C21 Bg 3 X1 20 3 NA N N 15 4390Default SU is closed PHR SN ans AA 4 8 sto PS e l N o carroll Zour 718v CS ll Haasan OLIM XINO 328 board revision C Designed and manufactured by OLIMEX LTD PLOUDIU BULGARIA 2013 https uuu olimex com 18ul zalke TI 10uF 10U Y This hardware design bu Olimex LTD is licensed under a Creative Commons fttribution Sharefllike 3 0 Unported License Page 19 of 23 OLIMEXINO 328 user s manual Note that all dimensions are in inches 6 2 Physical dimensions OLIMEXO 2013 evlolols Zv loes Yy lele ovoja o Q E 2 71nch RS ia Qa RIRI EE GE Lg OO 59999 Dl 5 lt Hcr qaa m m SEREAS ag q m go Sum 1 7 7 d Page 20 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 7 REVISION HISTORY AND SUPPORT 7 Introduction to the chapter In this chapter you will find the current and the previous version
4. UP THE OLIMEXINO 328 e ecce 8 2 Introduction to the Chapter cccccccsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssoseses 8 CHAPTER 5 INTERFACES AND HARDWARE e eee eee n eene nnne nue 13 5 Introduction to the chapter uiis ciii ea ois va cc eda ooi esu at cose ou ao oes sua ooo Ela eot pae eS Ege a Ea a SUR n 13 o I UE XT COMME GEOR 25iisiiiio ri cass coat use 2o a VOS eas v uis Do o Vosa o Sus vein 2o o OUR uo abu Us So oe Veo sapra a Se a VD oo au eis CURE TEES 13 5A PWR Ee C orcad A ORANE OT AEri 13 5 3 Arduino shield platform ccce ee eee eene nennen enses sese ease sese sessanta aaa 14 531 CONT POW ER sass 2 ciet ipis eso bee eo eee es sabe de e ears s esa E Vo ae e eee aseo Eee pace e uen ea rese a aee iaia 14 53 2 CON SANA LOG vivet escectet e eeoeuues oversee eee Eae lave Tu von ae ini LV pO Dea Qu ao Pw o EVER EVI 14 5 33 CONS R Le N 5 ii cessessscsssS ceuces cescevetekeeexuseecs spe du becepuuaseckve tas ae en sa Lega Le bou c ee eost coss 14 593 4 CONA DIGTDAT iiccsske centceo ses ess bere eee eos sa da ep Ee rase a eaae rosae c ae ee eee aiaiai 15 SE NERO Ie LC Rt ERA 15 SNB I I E A ER 15 Page 3 of 23 OLIMEX 2013 OLIMEXINO 328 user s manual 6 Introduction to the chapter i caadbdadasdsuslcdasssdddasadueacsanssbsdasssselcessdbidceradsascsarisiets dusslidisdslsasidsaisict
5. connect any other board that uses I2C SPI or UART interface without the need of soldering More information about the UEXT might be found here https www olimex com Products Modules UEXT Signal name VCC GND D1 TXD D RXD A5 SCL A4 SDA D12 MISO D11 MOSI D13 SCK LED1 UEXT_ CS 5 2 PWR_J connector The power jack used is the typical 2 5mm one used by Olimex in most of our products You should provide between 6 and 16 volts 1 5A maximum to the board Note that we also sell a couple of compatible 12V capable power supplies suitable for European customers These might be found here https www olimex com Products Power Pin Signal name 1 Power Input 2 GND Page 13 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 5 3 Arduino shield platform These four connectors are usually used when you want to mount extension shield on the OLIMEXINO 328 The shield connector layout follows the original Arduino layout and spacing BUT we have also provided set of metalized holes that improve the layout by keeping 0 1 step between connectors The extra holes might be used when the original connector get clunky of wires They can be used for placing measuring tools Olimex has a number of shields available They might be found here https www olimex com Products Duino Shields 5 3 1 CON1 POWER Signal name RESET 3 3V 5V GND GND VIN Signal name
6. held applications 1 4 Hardware revision of the board used in the manual Revision B and revision C boards and resources were used while writing this document It is possible that all revisions used to create the document are outdated so it is recommended to download the latest sources from the web page of OLIMEXINO 328 at the official www olimex com web site 1 5 Document organization Each section in this document covers a separate topic organized as follow Chapter 1 is an overview of the board usage and features Chapter 2 provides a guide for setting the board Chapter 3 contains the general board diagram and layout Chapter 4 mentions the control circuitry used in OLIMEXINO 328 Chapter 5 is an explanation of the connectors the LEDs and the jumpers position Chapter 6 contains the general board diagram and layout Chapter 7 contains the revision history useful links and support information Page 7 of 23 OLIMEX 2013 OLIMEXINO 328 user s manual CHAPTER 2 SETTING UP THE OLIMEXINO 328 2 Introduction to the chapter This section helps you set up the OLIMEXINO 328 development board for the first time Please consider first the electrostatic warning to avoid damaging the board then discover the hardware and software required to operate the board The procedure to power up the board is given and a description of the default board behavior is detailed 2 1 Electrostatic warning The OLIMEXINO 328 board is shipped in protective
7. of the document you are reading Also the web page for your device is listed Be sure to check it after a purchase for the latest available updates and examples 7 1 Document revision Revision date Changes Modified page A 20 08 11 Initial manual release B 14 11 13 Major document changes 7 2 Board revision Remember to check the schematics and the board design files to compare the differences oro pes release of the board 1 Changed 0805 LEDs to 0603 LEDs and resistors to 2K to reduce overall current consumption 2 Added new label Made in Bulgaria in the board file 3 Added jumpers that help disconnecting pull up resistors of signals of the Arduino shield platform 4 Added new label Designed by Olimex LTD in the schematic 5 Adjusted resistors 10uF 6 3V 0805 to 10uF 10V 0603 C Page 21 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 7 3 Useful web links and purchase codes The web page you can visit for more info on your device is https www olimex com Products Duino AVR OLIMEXINO 328 For more info on the original Arduino design please visit http arduino cc en Main arduinoBoardDuemilanove ORDER CODES OLIMEXINO 328 assembled and tested Arduino like board AVR ISP500 assembled and tested AVR ISP compatible programmer AVR ISP MK2 assembled and tested AVR ISP compatible programmer How to purchase Olimex products You can order from our web shop or from any of our distributors The
8. regulator for the Analog part allowing the ADC to be read correctly without digital noise pickup 11 We made provision for the optional ARef precision voltage source for users who need higher precision and temperature stability in Analog readings 12 We placed the LEDs and the BUTTONS on the edge of the board for easy access even if the boards have shields on them 13 All components were placed LOWER than the connectors so the shields do not interfere with them 14 We used a mini USB connector which is common and used in most cell phones so you do not have to buy other cables 15 The original design did not space the connectors at 0 1 making perfboard use impossible For compatibility we used the same spacing but we added footprints next to the connectors on 0 1 which customers can use with perforated boards 16 AII signals on the connectors are printed on top and on bottom of the board so when you check with a probe you know exactly which point you are measuring Page 6 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 17 We added 4 mounting holes making board attachment easier 1 3 Target market and purpose of the board The board is aimed at beginners due to the fact it might be programmed without the need of third party tools and the big Arduino community It is also suitable for professionals due to the industrial range of operation small form factor and wide power supply choice The board is suitable for hand
9. transfer in the FTDI Status LED with name RX green indicates that there is transfer in the FTDI Power on LED red with name PWR this LED shows that the board is power supplied User button with name BUT connected to ATmega328P pin 32 INTO PCINT18 PD2 signal D2 BUT User button with name RST connected to ATmega328P pin 29 PC6 RESET Switch with name SW 3 3V 5V selects between 3 3V and 5V power supply of the board Page 17 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 6 SCHEMATICS 6 Introduction to the chapter In this chapter is located information about the schematics describing logically and physically OLIMEXINO 328 6 1 Eagle schematics Stand alone search able schematic in PDF format might be found at the web page of OLIMEXINO 328 The schematic is also shown on the next page for quicker reference We mostly use Eagle by Cad Soft 4 16r2 for designing However the files should be compatible with the latest Eagle available Cad Soft offers a trial version of their software that allows you to inspect schematics and board files without being able to modify them This work is licensed under the Creative Commons Attribution ShareAlike 3 0 Unported License To view a copy of this license visit http creativecommons org licenses by sa 3 0 Page 18 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual BU USB E 2 D CRXD TXD RXD RTS cTs DTR amp DSR UCC PCINTZ XTAL2 TOSC2 P8
10. 7 DCD amp UCC PCINT6 XTAL1 TOSC1 PB6 RI SCK PCINTS PB5 acts cis PCINT4 MISO PB4 en ry PCINT3 0C2A MOSI PBS 180 nF 100nF CBUSO 4 7k fy Sreencas03 s PCINT2 8SS 0C18 PB2 I ceusi 5 PCINT1 0C1A PB1 u RX Po PCINT CLKO ICP1 PBO PC6 RESET PCINTA4 FTDI_BASIC PCS RDCS SCL PCINT13 PCA RDC4 SDR PCINT12 PC3 ADC3 PCINTA1 PC2 6DC2 PCINT1 PCL RDCA PCINTS PCO RDCO PCINTS D1 TXD sorov C9 zoen jeze A4CSDA ASCSCL ANALOG Ca RCNA ahaa PCINT23 RIN1 P07 DDD FT232RL SS0P28 a PCINT22 0C A AING PDS NACHR1X6 Suat PCINT21 0C B T1 PD5 D2 lt BUT AGND PCINT20 XCK TO DD4 PCINT19 0C28 INT1 PD3 D13XSCK LED1 49 2 DScLED2 gt INT PCINT18 PD2 Ance TXD PCINT17 PD1 RDC7 RXD PCINT16 P0 ATmega328P AU ESRI CC NACZTL434AF TAD DSCLED2 F Di L Di1Gdss LE E02 ZY Graecas ZY Velioucosom BE ZCHISOS D13 SCK LED1 DIGITAL D lt RXD gt DIGITAL ARDUINO PLATFORM amp CONNECTORS 07 018 R247 R25 4 2kL 10k DESEAN Ope D12MIS0 DZ 1 3 D1e C SS gt D1a lt TXD gt D CRXD 013 SCK LED1 ABCSCL ADR D11 HOSD Di2XHISO DAiHOSD RESET Battery Charger D13SCK LED1 UEXT CS GND URL MCP1700T 3302E MB FET2 IRLML 402 UDD
11. SCIO In Jumpers table 07218 5 D7 D1v 9 3euDcL ex gt N Page 11 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 4 CONTROL CIRCUITY 4 Introduction to the chapter Here you can find information about reset circuit and quartz crystals locations the power supply circuit is discussed 4 1 Reset OLIMEXINO 328 reset circuit includes R12 4 7kQ R13 3309 SD5 1N4148 C7 4 7nF C8 100nF jumper USB RST ATmega328P pin29 PC6 3RESET PCINT14 and RST button 4 2 Clocks Quartz crystal Q1 16 MHz is connected to ATmega328P pin 7 XTAL 1 and pin 8 XTAL2 Note that the crystal is on socket and can be changed to any value 4 3 Power supply circuit OLIMEXINO 328 can take power supply from external power supply 9 30 VDC 5V from USB 3 7V Li ion battery The programmed board power consumption is about 20mA with all peripherals enabled Page 12 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 5 INTERFACES AND HARDWARE S Introduction to the chapter In this chapter are presented the interfaces found on the programmed that can be found on the board Jumpers functions are described 5 1 UEXT connector The UEXT is used to connect additional extension modules to the OLIMEXINO 328 Most Olimex extensions named MOD X XXX can be plugged directly to this connector If you wish to add additional extras to your board this is the right interface Of course using jumper wires you might
12. anti static packaging The board must not be subjected to high electrostatic potentials General practice for working with static sensitive devices should be applied when working with this board 2 2 Requirements In order to set up the OLIMEXINO 328 optimally you might need to update your set of hardware and or software tools The major needed components are listed below Hardware tools USB type A to USB mini cable Personal computer with USB type A port Software tools any official Arduino IDE You would need additional hardware and software if you want to use OLIMEXINO 328 as a general purpose Atmel AVR board or you want to reprogram the bootloader required for Arduino IDE communication You would need to a have a working combination of a programmer tool and a software development environment You would also need a 6 pin header or jumper wires to establish proper hardware connection between the programmer tool and the board Currently OLIMEX sells a couple of ATmega328 compatible programmers that would also work with the most common software environments AVR Studio 4 and 5 Atmel Studio 6 AVRdude the built in Arduino programmer These programmers are AVR ISP500 and AVR ISP MK2 Page 8 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 2 3 Connecting to Arduino IDE The latest Arduino IDE might be downloaded from the official Arduino web site http arduino cc After you have downloaded and installed or extracted
13. apter on the market including applications with the standard 24VDC industrial power supply 3 We carefully selected all components to work reliably over the industrial temperature range 25 85C so the board can be used in industrial applications the original design was suitable for the commercial 0 70C operating temperature 4 The original Arduino design was not good for portable applications as it dissipated too much power in the linear voltage regulators We chose ULTRA LOW POWER voltage regulators with consumption of only few microamps to enable handheld and battery powered applications 5 We added a Li Ion rechargeable battery power supply option with a BUILT IN onboard charger so when a battery is attached it is automatically kept charged When the other power source USB or external adapter is removed it will AUTOMATICALLY power the board no jumpers no switches 6 Our design can work both on 3 3V and on 5V switch selectable 7 Our boards included the UEXT connector allowing many existing modules like RF ZIGBEE GSM and GPS to be connected It also saves soldering to interface I2C UART and or SPI 8 Our design allows a Real Time Clock RTC 9 We made our design noise immune in the RESET circuit There are a number of threads on the Arduino forum for problems with the RESET when the board works with motors since Atmel recommendations were omitted in the original design We fixed this 10 We used a separate voltage
14. ed the project after Arduino a local bar The name is an Italian masculine first name meaning strong friend The English pronunciation is Hardwin a namesake of Arduino of Ivrea More information can be found at the creators web page http arduino cc and in the Arduino Wiki http en wikipedia org wiki Arduino To make the story short Arduino is easy for the beginners with minimal Electronics knowledge while not restricting the professionals as they can program it in C or a mix of Arduino C language There are thousands of projects which make the startup easy as there is almost no field Arduino enthusiasts have not explored already 1 2 Improvements over the original Arduino design We entered the Arduino field 5 years after the design was introduced allowing us to see and skip most of the errors the Arduino inventors made We were able to read feedback from current customers and to implement what they wanted to see in the original Arduino There are a number of improvements over the original Arduino design that we have implemented in OLIMEXINO 328 1 We allowed the board to work at different frequencies with easy exchange of the quartz crystal 2 The original Arduino used a linear power supply This limited the input voltage range We designed a switching power supply to accept input voltages from 9 to 30V DC making it possible Page 5 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual to use virtually any power supply ad
15. ill not accept goods that have clearly been used more than the amount needed to evaluate their functionality If the goods are found to be in working condition and the lack of functionality is a result of lack of knowledge on the customers part no refund will be made but the goods will be returned to the user at their expense All returns must be authorized by an RMA Number Email support olimex com for authorization number before shipping back any merchandise Please include your name phone number and order number in your email request Returns for any unaffected development board programmer tools and cables permitted within 7 days from the date of receipt of merchandise After such time all sales are considered final Returns of incorrect ordered items are allowed subject to a 10 restocking fee What is unaffected If you hooked it to power you affected it To be clear this includes items that have been soldered to or have had their firmware changed Because of the nature of the products we deal with prototyping electronic tools we cannot allow returns of items that have been programmed powered up or otherwise changed post shipment from our warehouse All returned merchandise must be in its original mint and clean condition Returns on damaged scratched programmed burnt or otherwise played with merchandise will not be accepted All returns must include all the factory accessories which come with the item This i
16. list of official Olimex distributors might be found at https www olimex com Distributors Please check https www olimex com for more info 7 4 FAQ Q1 I installed the OLIMEXINO 328 drivers The board shows in Windows Device Manager correctly Yet the board cannot be programmed in Arduino IDE A1 Try installing older FTDI drivers FTDI drivers 2 08 14 or earlier should fix the issue The problem with the FTDI drivers is described in this forum post https www olimex com forum index php topic 2031 0 Q2 I have OLIMEXINO 328 and Olimex AVR ISP MK2 The drivers seem correct yet I m unable to program the board What might be causing the problem A2 Very often people try to use the PDI or TPI interface of AVR ISP MK2 for the ICSP slot of OLIMEXINO 328 Please use jumper wires to transform the 10 pin ICSP of the AVR ISP MK to 6 pin ICSP connector of the OLIMEXINO 328 Page 22 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual 7 5 Product support For product support hardware information and error reports mail to support olimex com All document or hardware feedback is welcome Note that we are primarily a hardware company and our software support is limited Please consider reading the paragraph below about the warranty of Olimex products All goods are checked before they are sent out In the unlikely event that goods are faulty they must be returned to OLIMEX at the address listed on your order invoice OLIMEX w
17. ncludes any In Circuit Serial Programming cables anti static packing boxes etc With your return enclose your PO Also include a brief letter of explanation of why the merchandise is being returned and state your request for either a refund or an exchange Include the authorization number on this letter and on the outside of the shipping box Please note It is your responsibility to ensure that returned goods reach us Please use a reliable form of shipping If we do not receive your package we will not be held liable Shipping and handling charges are not refundable We are not responsible for any shipping charges of merchandise being returned to us or returning working items to you The full text might be found at https www olimex com wiki GTC Warranty for future reference Page 23 of 23
18. rogrammer tool Please make sure you are not trying to use TPI or PDI interface with the ICSP pads If your programmer has only 10 pin ICSP cable you would need to use jumper wires or adapter to be able to connect to the 6 pin interface S 6 Jumper description The pictures below show the default jumper position Note that the board has only SMT jumpers which require soldering to close the jumper and melting the solder plus cutting between the pads to disconnect the jumper 5 6 1 USB RST jumper When closed USB RST jumper enables USB auto reset function After reset the bootloader is started and loads the program into the Flash Default state is closed 5 6 2 LED1_E jumper When closed LED1_E connects LED1 to D13 SCK line Default state is closed 5 6 2 D7 D10 jumper When D7 D10 jumper is closed in position D7 UEXT pin 10 UEXT CS is connected to Atmega328P pin 11 PD7 signal D7 when this jumper is closed in position D10 UEXT pin 10 UEXT CS is connected to Atmega328P pin 14 PB2 SS signal D10 3S S e Default state is closed in position D7 5 7 LEDs and buttons Status LED with name LED1 green connected via jumper LED1_E to ATmega328P pin 17 Page 16 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual SCK PCINTS PBS signal D13 SCK LED1 Status LED with name LED2 yellow connected to ATmega328P pin 13 PCINT1 OC1A PB1 signal D9 LED2 Status LED with name TX red indicates that there is
19. s 18 6 1 Eagle schematics 0000000000000000000000000000000090009000000009000000000000000009000000000000000000000000000000000000000000000000000090 Page 4 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 1 OVERVIEW 1 Introduction to the chapter Thank you for choosing the OLIMEXINO 328 board from Olimex This document provides a user s guide for the Olimex Arudino like OLIMEXINO 328 As an overview this chapter gives the introduction to Arduino the scope of this document and lists the features of the board The document s organization is then detailed 1 1 Introduction to Arduino Arduino is an open source electronics prototyping platform designed to make the process of using electronics in multidisciplinary projects more accessible The hardware consists of a simple open design for the Arduino board with an Atmel AVR processor and on board I O support The software consists of a standard programming language and the boot loader that runs on the board Arduino hardware is programmed using a Wiring based language syntax libraries similar to C with some simplifications and modifications and a processing based IDE The project began in Ivrea Italy in 2005 to make a device for controlling student built interaction design projects less expensively than other prototyping systems available at the time As of February 2010 more than 120 000 Arduino boards had been shipped Founders Massimo Banzi and David Cuartielles nam
20. ss for purpose are excluded This document is intended only to assist the reader in the use of the product OLIMEX Ltd shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product This evaluation board kit is intended for use for engineering development demonstration or evaluation purposes only and is not considered by OLIMEX to be a finished end product fit for general consumer use Persons handling the product must have electronics training and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards Olimex currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive Olimex assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS USED TO CREATE OLIMEXINO 328 THEY ARE CONSIDERED SUITABLE ONLY FOR OLIMEXINO 328 Page 2 of 23 OLIMEX 2013 OLIMEXINO 328 user s manual Table of Contents CHAPTER 2 SETTING
21. the environment you should connect the OLIMEXINO 328 to the computer via an USB type A to USB mini cable The first time you connect the board you would be asked for drivers You can find the drivers needed for OLIMEXINO 328 in the install folders of the Arduino IDE usually in folder drivers After the drivers are successfully installed you should run the Arduino IDE In Tools gt Board you should select Arduino Duemilanove w ATmega328 That is all Now you can load any built in example or you can refer to the number of demo examples in the SOFTWARE section of the OLIMEXINO 328 s web page https www olimex com Products Duino AVR OLIMEXINO 328 For more detailed instructions and Linux installation please check the following document https www olimex com Products Duino AVR OLIMEXINO 328 resources Install OLIMEXINO 328 pdf Page 9 of 23 OLIMEXO 2013 OLIMEXINO 328 user s manual CHAPTER 3 OLIMEXINO 328 BOARD DESCRIPTION 3 Introduction to the chapter Here you get acquainted with the main parts of the board Note the names used on the board differ from the names used to describe them For the actual names please check the OLIMEXINO 328 itself 3 1 Layout top view LED1 LED2 CON4 BUT TX LED mini USB RX LED 3 3V 5 0V LIPO_BAT POWER JACK POWERLED RST Page 10 of 23 OLIMEX 2013 OLIMEXINO 328 user s manual 3 2 Layout bottom view DESCRIP zs LED1 is 5onnected 9 013
Download Pdf Manuals
Related Search