Home

CPAW252NM Ultimate Short Throw LCD Data Projector User Manual

1. continued on next page 12 1 3 Manual network connection setting Wireless LAN continued 4 Select Use the following IP address and configure the IP address Subnet mask and Default gateway for the computer accordingly After setting is complete click OK to close the window About IP address The Network address portion of the IP address setting on your computer must be the same as the setting on the projector Also the entire IP address on the computer must not overlap with that of the other devices on the same network including the projector For example The projector s settings are as follows IP address 192 168 10 254 Subnet mask 255 255 255 0 Network address 192 168 10 in this case Therefore specify the computer s IP address as follows IP address 192 168 10 xxx xxx shows decimal number Subnet mask 255 255 255 0 Network address 192 168 10 in this case Select from 1 to 254 for xxx not duplicating with any other equipments In this case since the IP address of the projector is 192 168 10 254 specify a setting between 1 to 253 for the computer NOTE 0 0 0 0 cannot be set to the IP address e The projector s IP address can be changed by using the configuration utility via a web browser 320 e If the projector and the computer exist in the same network i e same network address you can leave the default gateway field blank e When the projector and
2. Cover Error The lamp cover has not been properly fixed Fan Error The cooling fan is not operating Lamp Error The lamp does not light and there is a possibility that interior portion has become heated Temp Error There is a possibility that the interior portion has become heated Lens Door Error The lens door is not opened or closed properly Air Flow Error The internal temperature is rising Cold Error There is a possibility that the interior portion has become overcooled Filter Error Filter time over Other Error Other error If displaying this error please contact your dealer Schedule Execution Error Schedule Execution error Q27 Lamp Time Alarm Lamp time over Alarm Time setting Filter Time Alarm Filter time over Alarm Time setting Transition Detector Alarm Transition Detector Alarm SECURITY menu in the Operating Guide Cold Start When the projector is supplied with the power it works as below e If the STANDBY MODE is set to the NORMAL the projector s power status changes from OFF to Standby state e If the STANDBY MODE is set to the SAVING the projector s power status changes from Standby state to ON lamp is turned on CLQSETUP menu in the Operating Guide Authentication Failure The SNMP access is detected from the invalid SNMP community Refer to LITroubleshooting in the Oper
3. Wireless Setup Configures the wireless LAN settings Mode Select Ad Hoc or Infrastructure IP Configuration Configures network settings DHCP ON Enables DHCP DHCP OFF Disables DHCP IP Address Configures the IP address when DHCP is disabled Subnet Mask Configures the subnet mask when DHCP is disabled Default Gateway Configures the default gateway when DHCP is disabled DNS Server Address Configures the DNS server address Select a channel from 1 to 11 to use in the AD HOC mode NOTE Depending on the country where you are the channels may vary In addition depending on the country or region where you are you may be required to use a wireless network card that confirm to the standards in the respective country or region Encryption Select data encryption method Input the WEP key Either ASCII characters or hexadecimal numbers can be used during WEP key input However you cannot use a combination of both The length of the key is defined as follows according to the WEP and character formats Encryption ASCII characters HEX numbers WEP 64bit 5 characters 10 characters WEP 128bit 13 characters 26 characters WPA Passphrase Input WPA Passphrase Available number of input characters is 8 to 63 Only alphabets numbers and following symbols can be used 5 amp lt gt WA h an
4. lt Authentication error reply gt Authentication Connection Error code ID 1 byte 65 7 4 Command Control via the Network continued Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established Authentication The projector does not accept commands without authentication success when authentication is enabled The projector uses a challenge response type authentication with an MD5 Message Digest 5 algorithm When the projector is using a LAN a random 8 bytes will be returned if authentication is enabled Bind this received 8 bytes and the Authentication Password and digest this data with the MD5 algorithm and add this in front of the commands to send Following is a sample if the Authentication Password is set to password and the random 8 bytes are a572f60c 1 Connect the projector 2 Receive the random 8 bytes a572f60c from the projector 3 Bind the random 8 bytes a572f60c and the Authentication Password password and it becomes a572f60cpassword 4 Digest this bind a572f60cpassword with MD5 algorithm It will be e3d97429adffa11bce1f7275813d4bde 5 Add this e3d97429adffa11bce1f7275813d4bde in front of the commands and send the data Send e3d97429adffa11bce1f7275813d4bde command 6 When the sending data is correct the command will be perfor
5. Security WEP 64 128bit WPA PSK TKIP AES WPA2 PSK TKIP AES SSID Computer application s system requirements OS Windows XP Home Windows XP Professional Windows Vista Home Basic Windows Vista Home Premium Windows Vista Business Windows Vista Ultimate Windows Vista Enterprise Windows 7 Starter Windows 7 Home Basic Windows 7 Home Premium Windows 7 Professional Windows 7 Ultimate Windows 7 Enterprise CPU Pentium 4 2 8 GHz or higher Graphic card 16 bit XGA or higher Memory 512 MB or higher Hard disk space 100 MB or higher Web browser Internet Explorer 6 0 or higher CD ROM drive USB wireless adapter Gemtek USB Link11n 69 1a Wananty and aftensalesisenvice If a problem occurs with the equipment please read 8 Troubleshooting L468 section first and review all suggested check points After that please contact your dealer or service company if you still have the problem They will tell you what warranty condition is applied 70
6. DNS Server Configures the DNS server address when DHCP is disabled To apply the settings click the Send button 4 User Password Configures the User Password To prompt the entry of User Password before starting e Control select the checkbox Item Description Configures the password You can specify a password up to 26 alphanumeric characters The usable symbols are space and the following amp 5 lt gt Th Reenter the above password for verification If the password is incorrect an error message is displayed New Password Confirm To apply the settings click the Send button 5 Admin Password Configures the Admin Password To prompt the entry of Admin Password before displaying the Tools window select the checkbox Item Description Configures the password You can specify a password up to 26 alphanumeric characters The usable symbols are space and the following amp lt gt Reenter the above password for verification If the password is incorrect an error message is displayed New Password Confirm To apply the settings click the Send button 46 3 2 Crestron e Control continued 3 2 3 Info window eZ RR RSRS SS RB MS eZ RRBRSSRSRS BS SA Projector information D Projector Status 1 SE eer 2 a E E U rouen RRC g U E E nn ES EEE B eee eee Znnnnnnnnnnnnt Displays the settings an
7. F meur F SETUP AUDIO SCREEN F SCREEN amp SERVICE ae e e Item Description SERVICE Quit Presenter Mode Quit compulsorily from the Presenter mode 38 3 1 Projector Web Control continued 3 1 11 Remote Control You can use your Web browser to control the projector The functions on the bundled remote control are assigned to the Web Remote Control screen e Do not attempt to control the projector with the projector s remote control and via your Web browser at the same time It may cause some operational errors in the projector Item Description POWER Assigned the same operation as STANDBY ON button COMPUTER Assigned the same operation as COMPUTER button VIDEO Assigned the same operation as VIDEO button BLANK Assigned the same operation as BLANK button FREEZE Assigned the same operation as FREEZE button MUTE Assigned the same operation as MUTE button MENU Assigned the same operation as MENU button Assigned the same operation as A button Assigned the same operation as WV button Assigned the same operation as lt button Assigned the same operation as button ENTER Assigned the same operation as ENTER button RESET Assigned the same operation as RESET button PAGE UP Assigned the same operation as PAGE UP button PAGE DOWN Assigned the same operation as PAGE DOWN
8. external device With using this method the computer and an external device will send the data out of synchronization If it is required to synchronize them set the computer to make the synchronization NOTE Incase that the computer controls to synchronize transmitting and receiving the data it may not be able to control an external device well depending on the processing status of the projector 55 A OANA FUGON 7 1 E mail Alerts The projector can automatically send an alert message to the specified e mail addresses when the projector detects a certain condition that is requiring maintenance or detected an error NOTE Up to five e mail addresses can be specified e The projector may be not able to send e mail if the projector suddenly loses power Mail Settings 124 To use the projector s e mail alert function please configure the following items through a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser and select Projector Web Control from the selection window 2 Enter your user name and password and then click the OK 3 Click the Mail Settings and configure each item Refer to item 3 1 5 Mail Settings 124 for further information 4 Click the Apply button to save the settings NOTE Click the Send Test Mail button in the Mail Settings to confirm that the e mail settings ar
9. if you want to perform the command every Sunday please select the Sunday 4 Click the Enable check box to enable scheduling 5 Enter the date month day for specific date scheduling 6 Click the Apply button to save the settings 7 After configure the time command and parameters click the Register to add the new event 8 Click the Delete button when you want to delete a schedule There are three types of scheduling 1 Daily Perform the specified operation at a specified time every day 2 Sunday Saturday Perform the specified operation at the specified time on a specified day of the week 3 Specific date Perform the specified operation on the specified date and time NOTE In standby mode the POWER indicator will flash green for approx 3 seconds when at least 1 Power ON schedule is saved e When the schedule function is used the power cord must be connected to the projector and the outlet The schedule function does not work when the breaker in a room is tripped The power indicator will lights orange or green when the projector is receiving AC power 60 7 3 Event Scheduling continued Date Time Settings 230 The Date Time setting can be adjusted via a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser and select Projector Web Control from the selection window 2 Enter your user name
10. AUDIO SOURCE VIDEO input port Assigns the AUDIO SOURCE in the standby mode continued on next page 36 3 1 Projector Web Control Projector Control continued Item Description OPTION AUTO SEARCH Turns the automatic signal search function on off DIRECT POWER ON Turns the direct power on function on off AUTO POWER OFF Configures the timer to shut off the projector when no signal is detected USB TYPE B Selects the USB TYPE B setting MY BUTTON 1 Assigns the functions for the MY BUTTON 1 button on the included remote control Assigns the functions for the MY BUTTON 2 button on the MY BUTTON 2 included remote control MY SOURCE Selects the My Source setting REMOTE FREQ Turns the remote control signal frequency normal function NORMAL on off REMOTE FREQ HIGH Turns the remote control signal frequency high function on off continued on next page 37 3 1 Projector Web Control Projector Control continued KA SSS D D eal ss The items shown in the table below can be Projector Control SERVICE performed using the Projector Control menu Confirm H D e chaeeharend Pmt Click the Quit Presenter Mode Network Setting Quit Presenter Mode Port Settings ans Alert Setting Schedule Settings Date Time Settings Security Settings ejector Control MAIN t PICTURE IMAGE
11. Authentication setting when authentication is required otherwise clear the check box 5 Click the Enable check box to open Network Control Port2 Port 9715 to use TCP 9715 Click the Enable check box for the Authentication setting when authentication is required otherwise clear the check box 6 Click the Apply button to save the settings 62 7 4 Command Control via the Network continued When the authentication setting is enabled the following settings are required 432 7 Click the Security Settings on the main menu 8 Click the Network Control and enter the desired authentication password See NOTE 9 Click the Apply button to save the settings NOTE The Authentication Password will be the same for Network Control Port Port 23 Network Control Port Port 9715 PJLink Port Port 4352 My Image Port Port 9716 and Messenger Port Port 9719 e The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking the Network Restart on the main menu HJ41 63 7 4 Command Control via the Network continued Command Format Command formats differ among the different communication ports e TCP 23 You can use the RS 232C commands without any changes The reply data format is the same as the RS 232C commands EQIRS 232C Comm
12. Operating Guide 17 3 1 Projector Web Control continued 3 1 2 Network Information Displays the projector s current network configuration settings Item Description Common Information Displays information common to both wireless and wired LAN Projector Name Displays the projector name settings Wi reless Information Displays the current settings of wireless LAN Mode Displays the mode of wireless LAN communication DHCP Displays the DHCP setting IP Address Displays the IP address Subnet Mask Displays the subnet mask Default Gateway Displays the default gateway DNS Server Address Displays the DNS server address MAC Address Displays the MAC address Ch Displays the channel used for wireless LAN Encryption Displays the data encryption setting SSID Displays the SSID used by the projector Speed Displays the current wireless LAN transmission speed ired Information Displays the current wired LAN settings DHCP Displays the DHCP setting IP Address Displays the IP address Subnet Mask Displays the subnet mask Default Gateway Displays the default gateway DNS Server Address Displays the DNS server address MAC Address 18 Displays the MAC address 3 1 Projector Web Control continued 3 1 3 Network Settings Displays and con
13. and password and then click the OK 3 Click the Date Time Settings on the main menu and configure each item Refer to item 3 1 8 Date Time Settings 130 for further information 4 Click the Apply button to save the settings NOTE The internal clock s time may not remain accurate Using SNTP is recommended to maintain accurate time 1371 e Once you turn off the projector in the SAVING mode ELQSETUP menu in the Operating Guide or the AC power the current date and time setting is reset 61 7 4 Command Control via the Network You can configure and control the projector via the network using RS 232C commands Communication Port The following two ports are assigned for the command control TCP 23 Network Control Port1 Port 23 TCP 9715 Network Control Port2 Port 9715 NOTE Command control is available only via the specified port above Command Control Settings 222 Configure the following items from a web browser when command control is used Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser and select Projector Web Control from the selection window 2 Enter your user name and password and then click the OK 3 Click the Port Settings on the main menu 4 Click the Enable check box to open Network Control Port1 Port 23 to use TCP 23 Click the Enable check box for the
14. refer for the appropriate group item in the LiveViewer User s Manual This model will be in the Group of F 15 Sn WAVE 0 CANO You can adjust or control the projector via a network from a web browser on a computer that is connected to the same network NOTE Internet Explorer 6 0 or later is required e If JavaScript is disabled in your web browser configuration you must enable JavaScript in order to use the projector web pages properly See the Help files for your web browser for details on how to enable JavaScript e It is recommended that all web browser updates are installed e If data is transferred via wireless and wired LAN at the same time the projector may not be able to process the data correctly Refer to the following for configuring or controlling the projector via a web browser Make sure that your computer and the projector is connected via network and then start Web browser Enter the projector s IP address into URL input box of the Web browser as the example below and then press the Enter key or gt button Example If the IP address of the projector is set to 192 168 1 10 Enter http 192 168 1 10 into the address bar of the web browser and press the Enter key or click button If a correct URL is input and the a projector and your computer are SE EE EE connected to the same network eo correctly the selection window as ETO shown on the right will be displayed You can cho
15. the Network Settings ELJ21 is set to Disable Crestron e Control cannot be used to operate the projector Enable Crestron e Control and close the web browser Next restart the web browser followed by entering the projector s IP address e Only English is supported on Crestron e Control e If the connection is terminated the Loading screen will appear Check the connection between the projector and the computer then return or refresh the Web page 3 2 Crestron e Control continued 3 2 1 Main window ee CY en Cr HITACHI 1 oe eee g a S 2 Computer in 1 sats 4 e L 3 You can operate the basic controls of the projector on this screen NOTE If the projector is in the standby mode only the Power button can be operated 1 Click a button and operate as follows Button Description Power Turns the power on off Vol Vol Adjusts the volume setting Mute Turns Mute on off 2 Sources List You can click a button to switch the input channel The cursor will move according to the currently selected input port Button Description Computer in1 Selects input from COMPUTER IN1 port Computer in2 Selects input from COMPUTER IN2 port LAN Selects input from LAN port USB Type A Selects input from USB TYPE A port USB Type B Selects input from USB TYPE B port HDMI Selects input from HDMI port S Video Selects input from S VIDEO port Video Selects inp
16. the computer exist in different networks the default gateway must be set continued on next page 13 1 3 Manual network connection setting Wireless LAN continued 5 Right click Wireless Network Connection to open the menu and select Connect Disconnect 6 From the connectable wireless networks select the SSID of the projector set to wireless by default and click Connect If you have enabled encryption a window asking for input of the encryption key will be displayed Input the preset key 7 After connection is established Connected will appear to the right of SSID 14 A NAmo Ie RSSSKS LOOM The projector can display or play back the computer screen images and audio data that are transmitted through the network This Network Presentation feature helps you to smoothly make your presentations and conduct conferences Wireless LAN Spo To use Network Presentation an exclusive application LiveViewer is required It can be installed from the bundled application CD You can also download the latest version and relevant information from the Hitachi website http www hitachi america us digitalmedia or http www hitachidigitalmedia com For details of Network Presentation and instructions to install the LiveViewer refer to the manual for LiveViewer LiveViewer function use depends on the model you are using If you want to use the latest downloaded LiveViewer please
17. the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser and select Projector Web Control from the selection window 2 Enter your user name and password and then click the OK 3 Click the Port Settings on the main menu 4 Click the Download MIB file to download a MIB file NOTE To use the downloaded MIB file specify the file by your SNMP manager 5 Click the Enable check box to open the SNMP Port Set the IP address to send the SNMP trap to when a Failure Warning occurs NOTE A Network Restart is required after the SNMP Port configuration settings have been changed Click the Network Restart and configure the following items 6 Click the Security Settings on the main menu 7 Click the SNMP and set the community name on the screen that is displayed NOTE A Network Restart is required after the Community name has been changed Click the Network Restart and configure the following items 8 Configure the settings for Trap transmission of Failures Warnings Click the Alert Settings on the main menu and select the Failure Warning item to be configured 9 Click the Enable check box to send out the SNMP trap for Failures Warnings Clear the Enable check box when SNMP trap transmission is not required 10 Click the Apply button to save the settings 58 7 3 Event Scheduling The scheduling function enables to setup scheduled events inclu
18. 313 AM evacuabon procedures Zn nmn nn hd When the administrator for Crestron RoomView Express sends out an alert message it will be displayed on the screen You can reply to the alert message via a chat format Input a message in the box below the alert message and click the Send button NOTE For details of Emergency Alert refer to the manual of Crestron RoomView Express e The alert message from Crestron RoomView is displayed on the screen of the projector in a way similar to the real time text of the Messenger function 0151 If another real time text is currently being displayed it will be overwritten by the alert message However if the priority of the real time text is set to high it will not be overwritten by the alert message and the latter will not appear on the screen of the projector For details refer to the manual for the application of the Messenger 49 Gis MIN Linn XoKey iuteuteig The projector can display still images that are transferred via the network Display image data ex Di MY IMAGE transmission requires an exclusive application for your computer Use the application to transfer the image data It can be downloaded from the Hitachi web site http Awww hitachi america us digitalmedia or http www hitachidigitalmedia com For information on the necessary settings and operations for the computer and projector refer to the manual
19. Assigns the MONITOR OUT in the standby mode 35 3 1 Projector Web Control Projector Control continued Item Description AUDIO VOLUME Adjusts the volume setting SPEAKER Turns the built in speaker on off AUDIO SOURCE COMPUTER IN1 Assigns the AUDIO SOURCE COMPUTER IN1 input port AUDIO SOURCE COMPUTER IN2 Assigns the AUDIO SOURCE COMPUTER IN2 input port AUDIO SOURCE LAN Assigns the AUDIO SOURCE LAN input port AUDIO SOURCE USB assigns the AUDIO SOURCE USB TYPE A input port AUDIO SOURCE USB TYPE B AUDIO SOURCE HDMI AUDIO SOURCE S VIDEO AUDIO SOURCE VIDEO AUDIO SOURCE STANDBY MIC LEVEL Selects the microphone level MIC VOLUME Adjusts the microphone volume setting SCREEN LANGUAGE Selects the language for the OSD MENU POSITION V Adjusts the vertical Menu position MENU POSITION H Adjusts the horizontal Menu position BLANK Selects the Blank mode START UP Selects the start up screen mode MyScreen Lock Turns MyScreen lock function on off MESSAGE Turns the message function on off TEMPLATE Selects the template setting C C DISPLAY Selects Closed Caption DISPLAY setting C C MODE Selects Closed Caption MODE setting C C CHANNEL Selects Closed Caption CHANNEL setting Assigns the AUDIO SOURCE USB TYPE B input port Assigns the AUDIO SOURCE HDMI input port Assigns the AUDIO SOURCE S VIDEO input port Assigns the
20. Configuration Protocol and has the function to provide necessary setting for network like IP address from server to client A server that has DHCP function is called DHCP server continued on next page 1 2 Manual network connection setting Wired LAN continued 1 2 3 Internet Option setting 1 Click Internet Options in Network and Sharing Center window to open Internet Properties window 2 Click Connections tab and then click LAN settings button to open Local Area Network LAN Settings 3 Uncheck all boxes in Local Area Network LAN Settings window After setting is complete click OK to close the window 10 Choase Setnngs you need to e a pracy server for a connecnon 1 3 Manual network connection setting Wireless LAN Using the designated USB wireless adapter option on the projector enables the projector and computer to communicate in both the Ad Hoc and Infrastructure modes This section is intended to explain how to set up wireless LAN connection manually 1 3 1 Preparation for wireless LAN connection Fig 1 3 1 6 With an access point communication Infrastructure Ad Hoc is one of the wireless LAN communication methods without having access point to communicate Infrastructure is one of the wireless LAN communication methods with having access point to communicate If certain quantities of equipments are used this mode i
21. Projector CP A222WN CP A302WN CP AW252WN Type nos CP A222WN CP A222WNM CP A302WN CP A302WNM CP AW252WN CP AW252WNM User s Manual detailed Network Guide Thank you for purchasing this product This manual is intended to explain only the network function For proper use of this product please refer to this manual and the other manuals for this product Features This projector has the network function that brings you the following main features v Network Presentation allows the projector to project computer images transmitted through a network L415 v Web Control allows you to monitor and control the projector through a network from a computer L416 v My Image allows the projector to store up to four still images and project them 150 v a allows the projector to display text sent from a computer through a network 2151 v Network Bridge allows you to control an external device through the projector from a computer 452 NOTE The information in this manual is subject to change without notice e The manufacturer assumes no responsibility for any errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment e Microsoft Internet Explorer Windows Windows Vista and Aero are registered trademarks of Microsoft Corporation in the U S and or other countries e Adob
22. Projector Web Control continued 3 1 5 Mail Settings Displays and configures e mail addressing settings Item Description Send Mail Click the Enable check box to use the e mail function Configure the conditions for sending e mail under the Alert Settings SMTP Server Address Configures the address of the mail server in IP format e The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings The maximum length of host or domain name is up to 255 characters Sender E mail address Configures the sender e mail address The length of the sender e mail address can be up to 255 alphanumeric characters Recipient E mail address Configures the e mail address of up to five recipients You can also specify the to or cc for each address The length of the recipient e mail address can be up to 255 alphanumeric characters Click the Apply button to save the settings NOTE You can confirm whether the mail settings work correctly using the Send Test Mail button Please enable Send mail setting before clicking the Send Test Mail e If you connect the projector to an existing network consult a network administrator before setting server addresses 24 3 1 Projector Web Control continued 3 1 6 Alert Settings Displays and configures failure amp alert settings Item Description
23. VEN Data length 8 bit fixed Start bit 1 bit fixed Stop bit 1 bit fixed 3 Using the TRANSMISSION METHOD menu set up the proper method for the CONTROL port according to your use NOTE The OFF is selected for the COMMUNICATION TYPE as the default setting e Using the COMMUNICATION menu set up the communication Remember that an unsuitable setup could cause malfunction of communication e When either one of the NETWORK BRIDGE settings is selected in the COMMUNICATION TYPE menu RS 232C commands cannot be received from the CONTROL port 6 3 Communication port For the NETWORK BRIDGE function send the data from the computer to the projector with using the Network Bridge Port that is configured in the Port Settings of web browser L23 NOTE Except for 41794 9715 9716 9719 9720 5900 5500 4352 between 1024 and 65535 can be set up as the Network Bridge Port number It is set to 9717 as the default setting 53 6 4 Transmission method The transmission method can be selected from the menus only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE OPTION menu gt SERVICE gt COMMUNICATION in the Operating Guide HALF DUPLEX e FULL DUPLEX 6 4 1 HALF DUPLEX This method lets the projector make two way communication but only one direction either transmitting or receiving data is allowed at a time The method does not allow the projector to receive the data from the co
24. ating Guide for further detailed explanation of Error except Other Error and Schedule Execution Error 25 3 1 Projector Web Control Alert Settings continued The Alert Items are shown below Item Description Configures the time to alert Alarm Time Only Lamp Time Alarm and Filter Time Alarm SNMP Trap Click the Enable check box to enable SNMP Trap alerts Click the Enable check box to enable e mail alerts Except Cold Start and Authentication Failure Configures the subject line of the e mail to be sent The length of the subject line can be up to 100 alphanumeric characters Except Cold Start and Authentication Failure Configures the text of the e mail to be sent The length of the text can be up to 1024 alphanumeric characters but if you are using some of special characters below the length may be shorter Special characters amp and space Except Cold Start and Authentication Failure Send Mail Mail Subject Mail Text Click the Apply button to save the settings NOTE The trigger of Filter Error e mail is depending on the FILTER MESSAGE setting in the SERVICE item of the OPTION menu which defines the period until the filter message is displayed on the projector screen An e mail will be sent when the usage time of the filter exceeds the time limit that is set No notification e mail will be sent if the FILTER MESSAGE is set to TURN OFF OPTION menu in the Operat
25. button SLIDESHOW Starts the Slideshow NOTE The Web Remote Control does not support repeat function that performs an action while holding a button clicked down e Since the repeat function is not available click the button repeatedly as many times as you require e Even if you hold the button clicked down for a while the Web Remote Control sends your request command one time only Release the button then click it again e When the POWER button is pushed a message window comes up to confirm the operation To control the power push OK otherwise push Cancel e The PAGE DOWN and PAGE UP buttons on the Web Remote Control cannot be used as mouse emulation function of the projector 39 3 1 Projector Web Control continued 3 1 12 Projector Status Displays the settings and status of the projector Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp Filter Time Displays the usage time for the current filter Power Status Displays the current power status Input Status Displays the current input signal source Blank On Off Displays the current Blank on off status Mute Displays the current Mute on off status Freeze 40 Displays the current Freeze status 3 1 Projector Web Control continued 3 1 13 Network Restart Ka NES H DH 5 D EE ee Restarts the p
26. cate due to configure wireless encryption settings If there is a wireless configuration utility loaded on your computer check its settings Please refer the manual of your configuration utility The computer and or projector s network settings are not configured correctly Check the network configurations of the computer and projector The same network address is set for both wireless and wired LAN Change the network address setting for wireless or wired LAN lt Only for wireless LAN gt The USB wireless adapter is not inserted into the projector Insert the optional USB wireless adapter lt Only for wireless LAN gt There is closely another projector or other that has the same wireless setting Try changing of SSID and IP Address Others Information from the projector to computer is not correct or completed The projector does not respond 68 Communication between the projector and computer is not working well NETWORK Functions of the projector is not working well Try NETWORK RESTART in SERVICE menu under the NETWORK menu In the Operating Guide 9 Specifications Item Specifications Control software Dedicated computer application and Web browser Corresponding protocol TCP IP DHCP client and HTTP server Network Wireless LAN IEEE802 11b g n Ad Hoc and Infrastructure modes Wired LAN 100Base TX 10Base T
27. d space continued on next page 20 Select an SSID from the list If you require to set your unique SSID select Custom then set your own SSID following the rules below Maximum number of input characters is 32 Only alphabets numbers and following symbols can be used 5 amp lt gt and space 3 1 Projector Web Control Network Settings continued Item Description Wired Setup Configures the wired LAN settings IP Configuration Configures network settings DHCP ON Enables DHCP DHCP OFF Disables DHCP IP Address Configures the IP address when DHCP is disabled Subnet Mask Configures the subnet mask when DHCP is disabled Default Gateway DNS Server Address Configures the DNS server address Other Setup Configures other network settings Set whether to or not to use Crestron e Control If you choose Disable the Logon window of Projector Web Control will be displayed at first but the selection window will not appear Configures the default gateway when DHCP is disabled Crestron e Control Click the Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu 441 e If you c
28. d status of the projector Click the Exit button to return to the Main window 1 Projector Information Item Description Projector Name Displays the projector name settings Location Displays the location name of the projector MAC Address Displays the wired LAN MAC address of the projector Displays the resolution and vertical frequency of the signal input selected on the projector Lamp Hours Displays the usage time for the current lamp Assigned To Displays the user name for the projector Resolution 2 Projector Status Item Description Power Status Displays the current power status Input Source Displays the current input signal source Picture Mode Displays the current picture mode setting Installation Displays the current installation setting Eco Mode Displays the current eco mode setting Error Status Displays the current error status NOTE Projector Name Location and the user name for Assigned To may appear truncated if they are too long 47 3 2 Crestron e Control continued 3 2 4 Help Desk window HITACHI Computer in 1 Sends receives messages to from the administrator for Crestron RoomView Express Description Sends a message Check the received message 48 3 2 Crestron e Control continued 3 2 5 Emergency Alert HITACHI Fire Alert Di M A fire emergency is in effect Please follow fire
29. ding power on power off It enables to be self management projector NOTE You can schedule the following control events Power Input Source My Image Messenger Slideshow 4128 e The power on event has the lowest priority among the all events that are defined at the same time e There are 3 types of Scheduling 1 daily 2 weekly 3 specific date L27 e The priority for scheduled events is as follows 1 specific date 2 weekly 3 daily e Up to five specific dates are available for scheduled events Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time e g Specific date No 1 has priority over Specific date No 2 and so on e Be sure to set the date and time before enabling scheduled events 1130 Once you turn off the projector in the SAVING mode EASETUP menu in the Operating Guide or the AC power the current date and time setting is reset 59 7 3 Event Scheduling continued Schedule Settings 27 Schedule settings can be configured from a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser and select Projector Web Control from the selection window 2 Enter your user name and password and then click the OK 3 Click the Schedule Settings on the main menu and select the required schedule item For example
30. e and Flash are registered trademarks of Adobe Systems Incorporated e Pentium is a registered trademark of Intel Corporation e JavaScript is a registered trademark of Sun Microsystems Inc e HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries e Crestron Crestron e Control e Control Crestron RoomView and RoomView are trademarks or registered trademarks of Crestron Electronics Inc in the United States and other countries Kail k e Trademark PJLink is a trademark applied for trademark rights in in Japan the United States of America and other countries and areas All other trademarks are the properties of their respective owners 1 UI e EE 4 1 Connection to the network ccccccceeseceeeseeeeeeeeeeeseaeeesseeneeees 5 1 1 System requirements aico2ic5 ecccsncuescectaneananeihiessundenisohibaencceacdeecesictidasteetea 5 1 1 1 Required equipment preparation EEN 5 1 1 2 Hardware and software requirement for computer sssssssesseeirererrsssssrerrenrrrnrrnnnsnssesset 5 1 2 Manual network connection setting Wired CAN c cceeeeeeeeeeeeeeeeees 7 121 Eg ip ments EE 7 122 Network 10 be ene eee nee E ee eee 7 1 2 3 Internet Option setting cosas cciijnecascasscuseasatardnesnoretasesuaiucninndass woehtocennesbanlantuieanaaiaauseanactsned 10 1 3 Manual network connection setting Wirel
31. e correct The following mail will be delivered to the specified addresses Subject line Test Mail lt Projector name gt Text Send Test Mail Date lt Testing date gt Time lt Testing time gt IP Address lt Projector IP address gt MAC Address lt Projector MAC address gt 56 7 1 E mail Alerts continued 5 Click the Alert Settings on the main menu to configure the E mail Alerts settings 6 Select and configure each alert item Refer to item 3 1 6 Alert Settings L 25 for further information 7 Click the Apply button to save the settings Failure Warning e mails are formatted as follows Subject line lt Mail title gt lt Projector name gt Text lt Mail text gt Date lt Failure Warning date gt Time lt Failure Warning time gt IP Address lt Projector IP address gt MAC Address lt Projector MAC address gt 57 7 2 Projector Management using SNMP The SNMP Simple Network Management Protocol enables to manage the projector information which is a failure or warning status from the computer on the network The SNMP management software will be required on the computer to use this function NOTE It is recommended that SNMP functions be carried out by a network administrator e SNMP management software must be installed on the computer to monitor the projector via SNMP SNMP Settings 223 Configure the following items via a web browser to use SNMP Example If the IP address of
32. e projector as a network terminal TCP IP data Protocol change Serial data Wired LAN RS 232C NA Wireless LAN Computer External device LAN port CONTROL port USB TYPE A port 6 1 Connecting devices 1 Connect the projector s LAN port to the computer s LAN port with a LAN cable or insert the USB wireless adapter into the USB TYPE A port 2 Connect the projector s CONTROL port and the device s RS 232C port with an RS 232C cable for RS 232C communication NOTE Before connecting the devices read the manuals for the devices to ensure the connection For RS 232C connection check the specifications of each port and use the suitable cable Connection to the ports in the Operating Guide Technical 52 6 2 Communication setup To configure the setup of the communication using NETWORK BRIDGE for the projector use items in the COMMUNICATION menu Open the menu of the projector and select the OPTION SERVICE COMMUNICATION menu LQOPTION menu gt SERVICE gt COMMUNICATION in the Operating Guide 1 In the COMMUNICATION TYPE menu select NETWORK BRIDGE WIRELESS or WIRED depending on the type of connection you use for the CONTROL port 2 Using the SERIAL SETTINGS menu select the proper baud rate and parity for the CONTROL port according to the specification of the RS 232C port of the connected device Item Condition BAUD RATE 4800bps 9600bps 19200bps 38400bps PARITY NONE ODD E
33. egins Month Configures the month daylight savings time begins 1 12 Week Configures the week of the month daylight savings time begins First 2 3 4 Last Day Configures the day of the week daylight savings time begins Sun Mon Tue Wed Thu Fri Sat hour Configures the hour daylight savings time begins 0 23 Time minute Configures the minute daylight savings time begins 0 59 d Configures the date and time daylight savings time ends Configures the month daylight savings time ends 1 12 Configures the week of the month daylight savings time ends First 2 3 4 Last Configures the day of the week daylight savings time ends Sun Mon Tue Wed Thu Fri Sat hour Configures the hour daylight savings time ends 0 23 minute continued on next page 30 Configures the minute daylight savings time ends 0 59 3 1 Projector Web Control Date Time Settings continued Item Description Configures the time difference Set the same time difference Time difference as the one set on your computer If unsure consult your IT manager Click the ON check box to retrieve Date and Time information from the SNTP server and set the following items SNTP Configures the SNTP server address in IP format e The address allows not only IP address but also domain SNTP Server Address name if the valid DNS s
34. erver is setup in the Network Settings The maximum length of host or domain name is up to 255 characters Configures the interval at which to retrieve Date and Time Cycle information from the SNTP server hour minute Click the Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking the Network Restart on the main menu H41 e If you connect the projector to an existing network consult a network administrator before setting server addresses e Once you turn off the projector in the SAVING mode EQSETUP menu in the Operating Guide or the AC power the current date and time setting is reset e To enable the SNTP function the time difference must be set e The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled e The internal clock s time may not remain accurate Using SNTP is recommended to maintain accurate time 31 3 1 Projector Web Control continued 3 1 9 Security Settings Displays and configures passwords and other security settings To apply changes to security settings click Apply then perform Network Restart Item Description User Account Configures the user name and password User na
35. ess LAN sssssssssssnsssnereeeennen 11 1 3 1 Preparation for wireless LAN connection cccccccecceeeeeeeeeeseseeseeeeeeeeseseeeeeeeeeeseeeeenenene 11 3 2 Wirel ss LAN COnMeCION Set Up sessed ieee 12 2 Network Presentation cccceceeeeesseeeeeeeeeeeneseeeeeseeeeseeneeseaes 15 d WED GOMOD EE 16 3 1 Projector Web Control EE 17 e LEE 17 3 1 2 NetWork IMTOFM ba E 18 3 1 3 Network Settings E 19 3 1 4 le e CC 22 SEO EE le Le e a a aa a r a a a a ea aE aE nS 24 ul 6 Alert Settings E 25 SE ev FUCA ER Settings metar e a E a T 27 3 1 8 Date Time Settings sxiicisrcisssondivncsassondncens cetaadswecuensonsinesnacussnenadeadeadnsunniadssaniuncternsincezmimssadnts 30 3 1 9 Security le EE 32 3 1 10 Projector Control eege ees 33 31 11 Remote Control EE 39 Gu KEE 40 3 1 13 Network E EE 41 RRE EE 42 E tele aces gett tavedin dione tance a ys vata aieed E E tanadaaniad 43 3 2 2 TOOS tee EE 45 Dio AAO WINDOW secossa a a 47 324 Klee WO cise E a e aaa a E E 48 3 2 5 Emergency Alert E 49 4 My Image Function ccsceceeeeseeeeeeeeeeeeeseeesaeeeseeeseeeeaneeeseees 50 5 Messenger FUNGON sciiisisccssnniisissisasnncsiacecdenddeabtudianstndscsiwancines 51 6 Network Bridge Function ccccceeeseeeeeeeeeeeeeseeeeeeeeeeeeeeeeees 52 6 1 Connecting Re E 52 6 2 Communication gege sticker reeacdencedcet uated pnasenaecesecs ecu vendedenddeeeesesn 53 6 3 Communication port ZeeiiegegeereegteE deeg 53 6 4 Transmis
36. figures network settings L Other Setup To apply changes to network settings click Apply then perform Network Restart mail Settings Network Restart Kg LE E 3 set Made On Item Description Common Setup Displays information common to both wireless and wired LAN Projector Name Configures the name of the projector The length of the Projector Name can be up to 64 alphanumeric characters Only alphabets numbers and following symbols can be used amp lt gt _ and space Particular projector name is pre assigned by default sysLocation SNMP Configures the location to be referred to when using SNMP The length of the sysLocation can be up to 255 alphanumeric characters Only numbers 0 9 and alphabet az A Z can be used sysContact SNMP Configures the contact information to be referred to when using SNMP The length of the sysContact can be up to 255 alphanumeric characters Only numbers 0 9 and alphabet az A Z can be used AMX DD AMX Device Discovery continued on next page Configures the AMX Device Discovery setting to detect the projector from the controllers of AMX connected to the same network For the details of AMX Device Discovery visit the AMX web site URL http www amx com as of Dec 2011 19 3 1 Projector Web Control Network Settings continued Item Description
37. for the application To display the transferred image select the MY IMAGE item in the NETWORK menu For more information please see the description of the MY IMAGE item of the NETWORK menu NETWORK menu in the Operating Guide NOTE It is possible to allocate the image file up to 4 in the maximum e Using MY BUTTON that registered MY IMAGE can display transferred image CQOPTION menu in the Operating Guide e The image file also can be displayed by using schedule function from the web browser Refer to item 7 3 Event Scheduling E159 in detail e If you display MY IMAGE data on screen while you are using the USB Display function the application for the USB Display will be closed To restart the application exit the MY IMAGE function and then the software in the projector LiveViewerLiteForUSB exe will run again EQUSB Display in the Operating Guide e If data is transferred via wireless and wired LAN at the same time the projector may not be able to process the data correctly 50 z MESMA RUNGON The projector can display text data transferred via the network on the screen and play back audio data inside the projector The text data can be displayed on the screen in two ways that displays the text transferred from the computer on real time and the other chooses and displays the text data from the ones once stored in the projector Today s Topics The chemical class is canceled The PE is performed at FT gym beca
38. he MyMemory data MYMEMORY RECALL Recalls the MyMemory data IMAGE ASPECT Selects the aspect setting OVER SCAN Adjusts the over scan setting V POSITION Adjusts the vertical position H POSITION Adjusts the horizontal position H PHASE Adjusts the horizontal phase H SIZE Adjusts the horizontal size AUTO ADJUST EXECUTE Performs the automatic adjustment INPUT PROGRESSIVE Selects the progressive setting VIDEO NR Selects the video noise reduction setting COLOR SPACE Selects the color space VIDEO FORMAT S VIDEO Selects the s video format setting VIDEO FORMAT VIDEO Selects the video format setting HDMI FORMAT Selects the HDMI format setting HDMI RANGE Selects the HDMI range setting COMPUTER IN e COMPUTER IN1 Selects the COMPUTER IN1 input signal type COMPUTER IN COMPUTER IN2 FRAME LOCK COMPUTER IN1 FRAME LOCK e COMPUTER IN2 Turns the FRAME LOCK COMPUTER IN2 function on off FRAME LOCK HDMI Turns the FRAME LOCK HDMI function on off continued on next page Selects the COMPUTER IN2 input signal type Turns the FRAME LOCK COMPUTER IN1 function on off 34 Item 3 1 Projector Web Control Projector Control continued Description SETUP D ZOOM Adjusts the zoom D SHIFT V Adjusts the vertical picture position D SHIFT H Adjusts the horizonta
39. he contents may be intercepted or it may cause unauthorized access to the system For details on wireless LAN security settings refer to 3 1 Projector Web Control or LINETWORK menu in the Operating Guide A CAUTION gt The optional IEEE802 11b g n USB wireless adapter uses the 2 4GHz radio frequency band You do not need a radio license to use the adapter but you should be aware of the following e DO NOT USE NEAR THE FOLLOWING e Microwave ovens e Industrial scientific or medical devices e Designated low power radio stations e Premises radio stations Using the USB wireless adapter near the above may cause radio interference which would result in a decrease in transmission speed or interruption and even lead to malfunctioning of devices such as pacemakers e Depending on the location where the USB wireless adapter is used radio wave interference may occur which may result in a decrease in transmission speed or interruption in communication In particular please be aware that using the USB wireless adapter at locations where there is reinforced steel other types of metals or concrete is likely to cause radio wave interference e Available Channels The USB wireless adapter uses the 2 4GHz radio frequency band but depending on the country or region you are in the channels that you can use might be limited Please consult your dealer for information on the usable channels e Bringing the optional USB wireless adapter out of the country or
40. hedule Configures the month and date Date Month Day This item appears only when Specific date No 1 5 is selected Click the Apply button to save the settings The current event settings are displayed on the schedule list To add additional functions and events set the following items Item Description Time Configures the time to execute commands Command Parameter Configures the commands to be executed Power Configures the parameters for power control Input Source Configures the parameters for input switching My Image Configures the parameters for My Image data display L450 Messenger Configures the parameters for Messenger data display E4157 Slideshow Configures the Start Stop parameters for the Slideshow Click the Register button to add new commands to the schedule list Click the Delete button to delete commands from the schedule list Click the Reset button to delete all commands and reset the schedule settings from the schedule list 28 3 1 Projector Web Control Schedule Settings continued NOTE After the projector is moved check the date and time set for the projector before configuring the schedules e The internal clock s time may not remain accurate Using SNTP is recommended to maintain accurate time e Events My Image and Messenger will not be executed appropriately but result in schedule execution error statu
41. ing Guide e Lamp Time Alarm is defined as a threshold for e mail notification reminder of the lamp time When the lamp hour exceeds this threshold that is configured in the Web page the e mail will be sent out e Filter Time Alarm is defined as a threshold for e mail notification reminder of the filter time When the filter hour exceeds this threshold that is configured in the Web page the e mail will be sent out 26 3 1 Projector Web Control continued 3 1 7 Schedule Settings Displays and configures schedule settings Description Configures the daily schedule Sunday Configures the Sunday schedule Monday Configures the Monday schedule Tuesday Configures the Tuesday schedule Wednesday Configures the Wednesday schedule Thursday Configures the Thursday schedule Friday Configures the Friday schedule Saturday Configures the Saturday schedule Specific date No 1 Configures the specific date No 1 schedule Specific date No 2 Configures the specific date No 2 schedule Specific date No 3 Configures the specific date No 3 schedule No 4 No 5 Specific date No 4 Configures the specific date No 4 schedule Specific date No 5 Configures the specific date No 5 schedule 27 3 1 Projector Web Control Schedule Settings continued The schedule settings are shown below Item Description Schedule Click the Enable check box to enable the sc
42. l menu Select an item with the mouse Most of the items have a submenu Refer to the table below for details Controls the projector lkl NOTE The setting value may not match with the actual value if the user changes the value manually In that case please refresh the page by clicking the Refresh button Item Description MAIN POWER Turns the power on off INPUT SOURCE Selects the input source PICTURE MODE Selects the picture mode setting BLANK ON OFF Turns Blank on off MUTE Turns Mute on off FREEZE Turns Freeze on off Controls the magnify setting MAGNIFY In some input signal sources it might stop Magnify even though it does not reach to maximum setting value MAGNIFY POSITION V Adjusts the vertical magnify position MAGNIFY POSITION H Adjusts the horizontal magnify position TEMPLATE Turns template on off MY IMAGE Selects MY IMAGE data MY IMAGE DELETE _ Deletes MY IMAGE data continued on next page 33 3 1 Projector Web Control Projector Control continued Item Description PICTURE BRIGHTNESS Adjusts the brightness setting CONTRAST Adjusts the contrast setting GAMMA Selects the gamma setting COLOR TEMP Selects the color temperature setting COLOR Adjusts the color setting TINT Adjusts the tint setting SHARPNESS Adjusts the sharpness setting ACTIVE IRIS Selects the active iris setting MYMEMORY SAVE Saves t
43. l picture position PICTURE POSITION CP A222WN CP A302WN Selects the vertical picture position PICT POSIT H CP AW252WN Selects the horizontal picture position KEYSTONE V Adjusts the vertical keystone distortion setting KEYSTONE H Adjusts the horizontal keystone distortion setting PERFECT FIT Adjusts the shape of the projected image in each of the corners and sides AUTO ECO MODE Turns on off the automatic eco mode function ECO MODE Selects the eco mode INSTALLATION Selects the installation status STANDBY MODE Selects the standby mode MONITOR OUT COMPUTER IN1 Assigns the MONITOR OUT when the COMPUTER IN1 input port is selected MONITOR OUT COMPUTER IN2 Assigns the MONITOR OUT when the COMPUTER IN2 input port is selected MONITOR OUT LAN Assigns the MONITOR OUT when the LAN input port is selected MONITOR OUT USB TYPEA Assigns the MONITOR OUT when the USB TYPE A input port is selected MONITOR OUT USB TYPE B Assigns the MONITOR OUT when the USB TYPE B input port is selected MONITOR OUT HDMI Assigns the MONITOR OUT when the HDMI input port is selected MONITOR OUT S VIDEO Assigns the MONITOR OUT when the S VIDEO input port is selected MONITOR OUT VIDEO Assigns the MONITOR OUT when the VIDEO input port is selected MONITOR OUT STANDBY continued on next page
44. lanation of network connection settings for Windows 7 1 Log on to Windows 7 as administrator authority Administrator authority is the account which can access to all functions 2 Open Control Panel from Start menu 3 Open View network status and tasks in Network and Internet With the icons in the Control Panel window displayed click Network and Sharing Center Adjust your computer s settings View by Small icons 4 Click Change adapter settings in the menu on the left side of the Network and Sharing Center window 8 Froubh problems Windows Firewall Diagnose and repair network problems or get troubleshooting information continued on next page 1 2 Manual network connection setting Wired LAN continued 5 Right click Local Area Connection to open the menu and select Properties 6 Select Internet Protocol Version 4 TCP IPv4 and click Properties 7 Select Use the following IP address and configure the IP address Subnet mask and Default gateway for the computer accordingly If a DHCP server exists in the network you can select Obtain an IP address automatically and the IP address will be assigned automatically After setting is complete click OK to close the window continued on next page 1 2 Manual network connection setting Wired LAN continued About IP address Setting manual
45. ly The Network address portion of the IP address setting on your computer must be the same as the setting on the projector Also the entire IP address on the computer must not overlap with that of the other devices on the same network including the projector For example The projector s settings are as follows IP address 192 168 1 254 Subnet mask 255 255 255 0 Network address 192 168 1 in this case Therefore specify the computer s IP address as follows IP address 192 168 1 xxx xxx shows decimal number Subnet mask 255 255 255 0 Network address 192 168 1 in this case Select from 1 to 254 for xxx not duplicating with any other equipments In this case since the IP address of the projector is 192 168 1 254 specify a setting between 1 to 253 for the computer NOTE 0 0 0 0 cannot be set to the IP address e The projector s IP address can be changed by using the configuration utility via a web browser L421 e If the projector and the computer exist in the same network i e same network address you can leave the default gateway field blank e When the projector and the computer exist in different networks the default gateway must be set Consult to the network administrator in detail Setting automatically When a DHCP server exists in the connected network it is possible to assign an IP address to the projector and computer automatically DHCP is abbreviation for Dynamic Host
46. me Configures the user name The length of the text can be up to 32 alphanumeric characters Password Configures the password The length of the text can be up to 255 alphanumeric characters Re enter Password Reenter the above password for verification Network Control Configures the Authentication password for Network Control Port1 Port 23 Network Control Port2 Port 9715 PJLink Port Port 4352 My Image Port Port 9716 and Messenger Port Port 9719 L22 23 Authentication Password Configures the Authentication password The length of the text can be up to 32 alphanumeric characters Re enter Authentication Password Reenter the above password for verification SNMP Configures the community name if SNMP is used Community name Configures the community name The length of the text can be up to 64 alphanumeric characters Click the Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking the Network Restart on the main menu e Only numbers 0 9 and alphabet az A Z can be used 32 3 1 Projector Web Control continued 3 1 10 Projector Control The items shown in the table below can be performed using the Projector Contro
47. med and the reply data will be returned Otherwise an authentication error will be returned NOTE As for the transmission of the second or subsequent commands the authentication data can be omitted when the same connection 66 7 5 Crestron RoomView Crestron RoomView is a multi user resource management program provided by Crestron Electronics Inc It is an application for managing and controlling the projector and other AV devices collectively For details of Crestron RoomView refer to the Crestron website URL http Awww crestron com The following communication interfaces can be used to manage the entire facility 1 Crestron RoomView Express Crestron RoomView Server Edition RoomViewTM Express and RoomViewTM Server Edition are software provided by Crestron Electronics Inc They are used for managing all the AV devices and are also able to communicate with the help desk as well as send out alert messages For details of the software refer to the following website URL http Awww crestron com getroomview 2 Crestron e Control Crestron e Control is a system controller that can be operated via a web browser E2142 67 8 Moubleshooting Problem Likely Cause Things to Check Reference Page Number Can t communicate Weak radio signal e Bring the computer and projector closer together e Radio waves won t go through concrete and metal steel doors etc Cannot communi
48. mputer while waiting for response data from an external device After the projector receives the response data from an external device or the response limit time is past the projector can receive the data from the computer That means that the projector controls transmitting and receiving the data to synchronize the communication To use the HALF DUPLEX method set up the RESPONSE LIMIT TIME following the instructions below _ TCP IP data Protocol change Serial data Wired LAN RS 232C 2 LAN cable RS 232C cable i Computer External device Wireless LAN A SE HE Org in ee Discarding data Response data Transmitting data Using the RESPONSE LIMIT TIME menu set the waiting time for response data from an external device GQOPTION menu gt SERVICE gt COMMUNICATION in the Operating Guide OFF 1s 2s 3s e OFF 54 6 4 Transmission method continued NOTE With using the HALF DUPLEX method the projector can send out 254 byte data as maximum at once e If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF the projector can receive the data from the computer and send it out to an external device continuously The OFF is selected as the default setting 6 4 2 FULL DUPLEX This method lets the projector make two way communication transmitting and receiving data at the same time without monitoring response data from an
49. n Professional Edition Windows Vista Home Basic Home Premium Business Ultimate Enterprise Service Pack 1 or later Windows 7 Starter Home Basic Home Premium Professional Ultimate Enterprise v CPU Pentium 4 2 8 GHz or higher v Graphic card 16 bit XGA or higher When using the LiveViewer it is recommended that the display resolution of your computer is set to 1024 x 768 v Memory 512 MB or higher v Hard disk space 100 MB or higher v Web browser Internet Explorer 6 0 or higher v CD ROM drive 1 1 System requirements continued NOTE The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item is set to SAVING Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL EQSETUP menu in the Operating Guide e You can get the latest version of the applications for the network functions of the projector and the latest information for this product from the Hitachi website http www hitachi america us digitalmedia or http www hitachidigitalmedia com 1 2 Manual network connection setting Wired LAN This section explains how to set it up manually 1 2 1 Equipments connection Connect the projector and a computer with a LAN cable Before connecting with an existing network contact the network administrator Next check the following computer settings 1 2 2 Network settings This is an exp
50. onnect the projector to an existing network consult a network administrator before setting server addresses e The WEP Key WPA passphrase and SSID settings will not be set if the invalid characters are used e The projector does not allow both wireless and wired LAN to be connected to the same network Do not set the same network address for both wireless and wired LAN 21 3 1 Projector Web Control continued 3 1 4 Port Settings Done Displays and configures communication port settings Description Network Control Port Port 23 Configures command control port 1 Port 23 Port open Click the Enable check box to use port 23 Authentication Click the Enable check box when authentication is required for this port Network Control Port2 Port 9715 Configures command control port 2 Port 9715 Port open Click the Enable check box to use port 9715 Authentication Click the Enable check box when authentication is required for this port PJ Link Port Port 4352 Configures the PJLink port Port 4352 Port open Click the Enable check box to use port 4352 Authentication Click the Enable check box when authentication is required for this port My Image Port Port 9716 Configures the My Image Port Port 9716 Port open Click the Enable check box to use port 9716 Authentication Click
51. ose to use Projector Web Control or Crestron e Control as a tool for controlling the projector Click one of them For more details refer to 3 1 Projector Web Control 2117 or 3 2 Crestron e Control G42 NOTE If Crestron e Control in the Network Settings R21 is set to Disable the selection window above does not appear but the Logon window of the Projector Web Control is displayed e Crestron e Control is created using Flash You need to install Adobe Flash Player on your computer to use Crestron e Control 16 3 1 Projector Web Control 3 1 1 Logon To use the Projector Web Control function you need to logon with your user name and password ae ee ee eat aah ee connection Below are the factory default settings for user wil pen name and password Remedi L ge 71 canca Logon window User name Password Administrator lt blank gt Enter your user name and password and then click the OK If you logon successfully the screen below will be displayed Main menu Common Information CRW 24 S a L E L a 95m mmmn E S Click the desired operation or configuration item on the main menu NOTE The language used on the Projector Web Control screen is the same as that of the OSD on the projector If you want to change it you need to change the OSD language on the projector SCREEN menu in the
52. region you reside in and using it there could lead to a violation of the radio laws of that country or region IE CONNAN O O MAWONI 1 1 System requirements 1 1 1 Required equipment preparation The following equipments are required to connect the projector to your computer through the network m Common The projector 1 unit Computer minimum 1 set m Depending on how you want to connect 1 For the wired connection 1 LAN cable CAT 5 or greater 1 piece 2 For the wireless connection 2 Projector side IEEE802 11b g n USB wireless adapter option USB WL 11N 1 unit Computer side IEEE802 11 b g n wireless LAN equipment 1 unit for each 3 1 The system for using the network function of the projector requires communication environment conforming 100Base TX or 10Base T 2 An access point is required when the wireless LAN connection is used as Infrastructure mode 3 Depending on the type of wireless network device and computer you are using the projector may not be able to communicate properly with your computer even if the computer is equipped with a built in wireless LAN function To eliminate communication problems please use a Wi Fi certified wireless network device 1 1 2 Hardware and software requirement for computer To connect your computer to the projector and use the network function of the projector your computer needs to meet the following requirements v OS One of the following Windows XP Home Editio
53. rojector s network connection Network Restart Confirm Restarting requires you to re og in in order to futher Cento or corar te procio a a web browser nestani Port Settings Alert Settings Meel Done E intent retecet Mode On Description Restart Restarts the projector s network connection in order to activate new configuration settings NOTE Restarting requires you to re log on in order to further control or configure the projector via a web browser Wait 30 seconds or more after clicking the Restart button to log on again 41 3 2 Crestron e Control Sources List Computer in 1 The Main window as shown above is displayed at first However if you have enabled User Password on the Tools window 0146 a dialog prompting you to enter the password as shown on the right will be displayed and no operation is enabled until you have entered the password After entering the preset password the dialog disappears and the Main window will be displayed As shown below you can open a window by clicking the corresponding tab at the top right User Password dialog of the window HITACHI Description Logs out from e Control Logout This tab appears only when User Password of the Tools window is enabled Tools Opens Tools window 145 Info Opens Info window 147 Contact IT Help Opens Help Desk window 1148 NOTE If Crestron e Control in
54. s efficient If communicating with existing network consult to your network administrator First insert the USB wireless adapter into the USB TYPE A port Connecting with your devices in the Operating Guide Then set up the computer for wireless communication When the computer comes with a built in IEEE802 11b g n wireless LAN device enable it and disable other network connections If a wireless LAN device is not built into the computer connect an IEEE802 11b g n wireless LAN device and install the device driver For details refer to the user s guide for the computer and wireless LAN device 1 3 Manual network connection setting Wireless LAN continued 1 3 2 Wireless LAN connection set up Using wireless LAN utility for Windows 7 standard Wireless LAN initial settings for the projector is as follows Connection Control Ad Hoc SSID wireless Channel dl Encryption rating None IP address 192 168 10 254 You can change these settings via a web browser on your computer or from the menu of the projector Refer to the item 3 1 3 Network Settings E120 or NETWORK menu in the Operating Guide 1 Select Change adapter settings from the menu on the left side of the Network and Sharing Center window Windows Firewall 2 Right click Wireless Network Connection to open the menu and select Properties 3 Select Internet Protocol Version 4 TCP IPv4 and click Properties
55. s in case lamp does not light or and display data are not stored in the projector at the scheduled event execution time e Events Input Source and My Image will not be executed if security feature is enabled and the projector is locked due to the feature e Certain error state in the projector such as temperature error lamp error will prevent the projector from appropriate execution of scheduled functions events e If no USB memory device is inserted to the projector or no image data for display exists at the scheduled event time a schedule execution error occurs against the scheduled Slideshow event e When you start the Slideshow input source will be automatically switched to the USB TYPE A port e Image files stored in the root directory of the USB memory device will be displayed for the scheduled Slideshow e Please refer to Troubleshooting in the Operating Guide in case scheduled functions events are not executed appropriately as you ve set 29 3 1 Projector Web Control continued 3 1 8 Date Time Settings Displays and configures the date and time settings Description Current Date Configures the current date in year month day format Current Time Configures the current time in hour minute second format Daylight Savings Time Click the ON check box to enable daylight savings time and set the following items Start Configures the date and time daylight savings time b
56. sion method EE 54 641 HALF DUPLEX eege hee 54 BEE 55 7 Other PUNGUONS E 56 7 1 E mail Alerts enetctecaacaneceastinen davsteanavaavanenamtancaedomentanesantoreauc de tsaanai se ecinannnenetaned 56 7 2 Projector Management using SNMP n asnnansssassnnnnnnnsssnnnnnnnrsssnnnrrrenssrnnrnnne 58 7 3 Event Scheduling EE 59 7 4 Command Control via the Network 62 7 5 Crestron OO IC Ee 67 8 Troubleshooting ssssssssssssssnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nenna 68 BT e E 69 10 Warranty and after sales service cccccceeeeeeeeeeeneeeeeeeees 70 To use the wireless network function of this projector the designated USB wire less adapter that is sold as an option is required For precautions according to the standards and laws refer to the documents that come with the adapter Restriction on plugging and unplugging the USB wireless adapter Before you insert or pull out the USB wireless adapter from the projector turn off the power of the projector and pull out the power cord s plug from the outlet Do not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power Do not use any extension cable or device when connecting the adapter to the projector Security precautions when using wireless LAN It is recommended that security settings such as SSID and ENCRYPTION are specified when using wireless LAN communication If the security settings are not specified t
57. the Enable check box when authentication is required for this port Messenger Port Port 9719 Configures the Messenger Port Port 9719 Port open Click the Enable check box to use port 9719 Authentication continued on next page 22 Click the Enable check box when authentication is required for this port 3 1 Projector Web Control Port Settings continued Item Description SNMP Port Configures the SNMP port Port open Click the Enable check box to use SNMP Trap address Configures the destination of the SNMP Trap in IP format e The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings The maximum length of host or domain name is up to 255 characters Download MIB file Downloads a MIB file from the projector twork Bridge Port Configures the Bridge port number Port number Input the port number Except for 41794 9715 9716 9719 9720 5900 5500 4352 between 1024 and 65535 can be set up It is set to 9717 as the default setting Click the Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking the Network Restart on the main menu 41 23 3 1
58. unication in the Operating Guide Technical However the following reply will be sent back in the event of authentication failure when authentication is enabled lt Reply in the event of an authentication error gt Reply Error code Ox1F 0x04 0x00 e TCP 9715 Send Data format The following formatting is added to the header 0 x 02 Data length 0 x 0D Checksum 1 byte and Connection ID 1 byte of the RS 232C commands Header Data length RS 232Ccommand Check Sum oe 0x02 0x0D 13 bytes 1 byte 1 byte Header 0x02 Fixed Data length RS 232C commands byte length 0x0D Fixed RS 232C command RS 232C commands that start with OxBE OxEF 13 bytes Check Sum This is the value to make zero on the addition of the lower 8 bits from the header to the checksum Connection ID Random value from 0 to 255 This value is attached to the reply data 64 7 4 Command Control via the Network continued Reply Data format The connection ID the data is same as the connection ID data on the sending data format is attached to the RS 232C commands reply data lt ACK reply gt Connection ID 1 byte lt NAK reply gt Connection ID 1 byte lt Error reply gt Error code SEH 2 bytes 1 byte lt Data reply gt Connection ID 1 byte lt Projector busy reply gt Connection ID 2 bytes 1 byte Status code
59. use today due Ge to bad weather gt Display text data ex B DN abcdefghijkimnopqrstuvwxyz D ABCDEFGHIJKLMNOPQRSTUWXYZ B 0123456789 Today s Topics The chemical WARNING FIRE ALERT Messenger function requires an exclusive application for your computer To edit transfer and display the text data use the application You can download it from the Hitachi web site http www hitachi america us digitalmedia or http www hitachidigitalmedia com For information on the necessary settings and operations for the computer and projector refer to the manual for the application NOTE It is possible to store the text data up to 12 in the maximum e Using MY BUTTON that registered MESSENGER can turn the displaying messenger text on off GQOPTION menu in the Operating Guide e The text file also can be displayed by using schedule function via the web browser Refer to item 7 3 Event Scheduling E159 for the detail e If data is transferred via wireless and wired LAN at the same time the projector may not be able to process the data correctly 51 S NGAO COS REUNAN This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface By making use of the NETWORK BRIDGE function a computer that is connected to the projector via wireless or wired LAN is able to control an external device via RS 232C communication using th
60. used the input text or numbers cannot be set correctly e All items on this window cannot be left blank 1 Crestron Control Configures the settings of Crestron control system devices Item Description IP Address Configures the IP address of the control system IP ID Configures the IP ID of the control system Port Specifies the port number used for communication by the control system To apply the settings click the Send button 2 Projector Configures the network settings of the projector Item Description Configures the name of the projector The length of the Projector Name Projector Name can be up to 64 alphanumeric characters Configures the location name of the projector You can specify Location a Location name up to 32 alphanumeric characters Configures the user name for the projector You can specify a user name up to 32 alphanumeric characters Assigned To The usable symbols are space and the following l 8 amp lt gt N h To apply the settings click the Send button 45 3 2 Crestron e Control Tools window continued 3 Projector continued Configures the network settings of the projector Item Description DHCP Enables DHCP IP Address Configures the IP address when DHCP is disabled Subnet Mask Configures the subnet mask when DHCP is disabled Default Gateway Configures the default gateway when DHCP is disabled
61. ut from VIDEO port 43 3 2 Crestron e Control Main window continued 3 Click a button and operate as follows To show the hidden buttons click the lt gt icons at the left and right ends Button Description Freeze Turns Freeze on off Contrast Adjusts the contrast setting Brightness Adjusts the brightness setting Color Adjusts the color setting Sharpness Adjusts the sharpness setting Magnify Controls the magnification setting using the buttons Use the A Y lt 4 gt buttons to move to the area you want to magnify Auto Performs the automatic adjustment Blank Turns Blank on off 4 Click the button and operate in the same way as the bundled remote control Button Description Assigned the same operation as MENU button Assigned the same operation as ENTER button Assigned the same operation as RESET button Assigned the same operation as A button Assigned the same operation as V button Assigned the same operation as lt button 44 Assigned the same operation as gt button 3 2 Crestron e Control continued 3 2 2 Tools window 2 1 4 3 5 Send ee Seng jE Zannnnnnnnft Configures the settings between the projector and Crestron control system Click the Exit button to return to the Main window NOTE If two byte characters are

CPAW252NM Ultimate Short Throw LCD Data Projector User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents