FMX2 Multilingual Manual (English
Contents
1. Combination of spacers G H or l depending on length of bolt and depth of recess Bolt A thru F Washer J or K Diagram A WARNING VAN Never overtighten a bolt into the back of your flat panel TV Do not lay the TV face down on its glass front Use a TV stand or lean against a wall Step 2 Mount Wall Plate Before you start drilling attach the Wall Plate Template to your wall It will make marking and drilling level pilot holes easier and catch a lot of the dust Remember to remove it before you attach the wall plate Wood Stud Wall Brick or Concrete Wall The Wall Plate must be mounted to two wood studs Use Attach the Wall Plate Template to the wall at the a stud sensor to locate the two studs clearly marking the desired height using a long level to ensure that the centers of the studs Use a long level to make sure these template is level Mark six hole locations on the wall for marks are horizontally level Attach the Wall Plate Template the concrete anchors we suggest placing the holes as to the wall at the desired height so that the stud centers shown in Diagram C where possible Drill the six holes are visible through mounting slots and drill four pilot perpendicular to the wall using a masonry bit see Diagram holes Once you have drilled the pilot holes remove the C Do not drill into mortar joints Remove the Wall Plate Wall Plate Template Template2. JT a N ae uu e q N A U k Hammer for 3 8 7 32 Socket Phillips concrete Crescent Stud Drill Masonry Wood set Screwdriver installs Wrench Finder Bit Bit J Supporting your digital lifestyle Step 1 Attach TV Brackets There are a wide variety of TVs available that reguire an assortment of bolt sizes We provide a selection of mounting bolts to fit most TVs If you have any concerns about this mounting hardware or installation call us direct at 1 888 848 2643 or email at support kantoliving com Step 1 1 Select the correct size of bolt If your TV has a curved back or the mounting holes are recessed you can use a combination of spacers G H or I depending on the selected bolt to ensure a proper fit You can use spacers inside or outside the bracket arm as Part items A B C D E or F shown in Diagram A Kanto provides 3 bolt diameters Metric sizes M5 M6 and M8 in various lengths Select the correct diameter bolt and hand screw into the Step 1 2 Attach TV brackets to the back of the TV k of the TV ine th l h Paok DIO determine ESER Now that you have selected the correct bolt length and Use washer J for bolts A B D or E M5 or M6 size and combination of spacers it s time to attach the brackets to washer K for bolts C or F M8 size the TV as shown in Diagram A 7 yr
3. Insert a Concrete Anchor M into each of these holes until it is flush with the wall surface Attach the Wall Plate using four Lag Bolts L and Lag Bolt Washers K see Diagram B Make sure the Wall Plate is Place the Wall Plate over the six anchors then mount using flat against the wall surface Do not over tighten Lag Bolts the Lag Bolts L and Washers K Make sure the Wall Plate L is flat against the wall surface Do not over tighten Lag Bolts L Wood 3 5 90mm Concrete 3 5 90mm 4 A 3 8 10mm Diagram B Diagram C CAUTION CAUTION Make sure the supporting surface will support Make sure the concrete or brick wall is at least 3 5 the load limits outlined in the Caution at the bottom thick Make sure the anchor is seated completely flush of page two Tighten Lag Bolts until the Wall Plate is flat with the concrete surface even if there is another layer against the wall Do not overtighten Lag Bolts L Each of material such as drywall If drywall is over 5 8 thick Lag Bolt must be screwed into a wood stud custom lag bolts must be used Concrete must be a minimum of 2000psi in density Supporting your digital lifestyle CAUTION Read this section carefully prior to install Step 3 Attach TV to TV Plate With the TV brackets firmly secured to the TV use two people to lift the TV into position and hook the TV brackets onto the TV plate as shown in Diagram D Tighten
4. cables into the cable management clips pro vided on the mount arms as shown in Diagram You may move the clips from one side to the other by removing the screws that hold the clips to the bottom of the mount arms Your installation is complete Diagram I Supporting your digital lifestyle Kanto Check out more great products from Kanto Kanto Speakers e Check out our full line of bookshelf and desktop speaker systems e Available in a stunning array of colors e Visit kantospeakers com for more O e e Full line of Audio and Video Cables e White or Black Cables available e HDMI Optical Mini jack RCA USB 6 Switchers Hubs and Adapters We by Kanto fF Visit kantoliving com products cables 6l i gt To learn more about all our products visit www kantoliving com f Kanto Living t kantoliving o kantoliving Warranty Limited Warranty To Original Purchaser Kanto Distribution Inc Kanto warrants the equipment it manufactures to be free from defects in material and workmanship for the following limited warranty period of 24 months parts and labour If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date of shipment with proof of original invoice Kanto will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electric
5. safety bolts at the bottom of the TV brackets as shown in Diagram E Hook Diagram D Diagram E Step 4 Level the TV The FMX2 comes pre tensioned at the factory to allow you to level the TV 5 by simply holding the TV and twisting up or down as shown in Diagram F If you need to tighten or loosen the level mechanism use a crescent wrench to tighten the two top nuts as shown in Diagram G Diagram F Mr WARNING Use two people to lift and position the TV onto the TV Plate Step 5 Tilt the TV The FMX2 will tilt 14 8 to provide the ideal viewing angle Loosen the tilt lever on the right side by rotating it counter clockwise from bottom to top as shown in Diagram H Loosen the tilt lever on the left side by rotating it counter clockwise from top to bottom To loosen further flip the lever to avoid contact with the TV plate Tilt the TV to the desired angle then tighten the tilt levers by rotating them clockwise On the right side this is from top to bottom as shown in Diagram H on the left side from bottom to top To tighten further flip the lever to avoid contact with the TV plate Diagram H Step 6 Cable Management Insert your
6. the type of wall you may have Kanto cannot be liable for property damage or injury caused by incorrect mounting incorrect assembly lifting or incorrect use of this product See installation video online at www kantoliving com product mounts FMX2 video Visit our Website for the most recent version of this manual CAUTION The maximum loading weight is 130 Ibs 59 kg This wall mount is intended for use up to the maximum weight restrictions indicated Use with products heavier than the maximum weights indicated may result in instability causing possible injury N CAUTION The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the wall mount combined Do not use this product for any purpose other than to mount a flat panel TV on a vertical surface as outlined in this manual Improper installation may cause damage to your TV or serious injury This product should not be mounted to steel stud walls cinder block or old concrete walls Consult a gualified installation contractor if you are unsure about the type of wall you may have A M5 x 12mm B M6 x 12mm C M8 x 25mm D M5 x 30mm Bolt Bolt Bolt Bolt x4 x4 x4 S x8 E M6 x 35mm F M8 x 40mm G M5 M6 H M5 M6 M8 Bolt Bolt 14mm Plastic Spacer 10mm Plastic Spacer l M5 M6 M8 J M5 M6 Washer K M8 Washer L Lag Bolt 5mm Plastic Spacer Lag Bolt Washer M Concrete Anchor Required Tools
7. English kanto s User Manual FMX2 TV Mount 130 Ibs 59 kg Supporting your digital lifestyle Table of Contents Table of Contents Introduction 2 Setup Steps3to4 Meu 6 Supplied Parts amp Hardware lt 3 Setup Steps 5106 YAA a yR 7 Setups Step la 45 soa dada dd ddd dU ddod 4 Other Kanto Produttes a v6 44 sv es yous ae YR 8 Setup Step 25 aiaiai ipea aaa 5 Warranty e aeann deine a 8 Introduction Thank you for choosing a Kanto full motion TV wall mount The FMX2 is designed to mount flat panel televisions weighing up to 130 Ibs 59 kg extend up to 20 56 cm from your wall allows you to swivel left and right 80 and tilt your TV 14 8 You can also adjust the horizontal level 5 Read these instructions fully before installation of this mount If you do not understand these directions or have any doubts about the safety of the installation please consult a qualified installation contractor to install this mount Make sure there are no defective or missing parts Do not use defective parts If there is hardware missing or if you are uncertain whether the part is defective call Kanto directly at 1 888 848 2643 or email support kantoliving com This product should not be mounted on steel stud walls or cinder block walls Consult a qualified installation contractor if you are unsure about
8. al or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the repair Such repairs are warranted for 90 days from the day of reshipment to the original purchaser This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed The information in the owner s manual has been carefully checked and is believed to be accurate However Kanto assumes no responsibility for any inaccuracies that may be contained in the manual In no event will Kanto be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages www kantoliving com support kantoliving com Tel 888 848 2643
Download Pdf Manuals
Related Search