CDU 5211 User Manual .indd - Pdfstream.manualsonline.com
Contents
1. Keep the area around the CD ROM drive clean from dust smoke and other contaminants 2001 Sony Australia 7 INTRODUCTION Features The CDU 5211 1s an internal CD Rom Compact Disc Read Only Memory drive unit designed for use with personal computers It comes with the following features General Speed 52X max 40X default Maximum Speed Choice function 40 Pin ATAPI IDE interface e 5 inch half height drive form factor Power loading and eject of a disc ABS Auto Balance Spindle to reduce noise and vibration 128 KB of buffer memory Power saving functions Vertical mount ability Small CPU bandwidth consumption Software volume control Easy audio CD DA control button Supported Disc Formats The CD 5211 is a Multiread compliant drive and can read data in each of the following formats CD DA CD ROM Mode 1 CD ROM XA Mode 2 Form 1 amp Form 2 CDI Ready Photo CD Karaoke CD Video CD MPEG 1 Enhanced CD CD Extra I Trax CD CD Text UDF Media Types CD ROM CD R and CD RW 12cm amp 8cm discs Audio Outputs 16 bit digital data over the ATA interface e Audio line output rear panel and headphones jack front panel for audio CD playback 2001 Sony Australia INTRODUCTION Software Requirements Reading Data For your computer to recognise your new CD Rom drive and to be able to access data from it the correct device drivers2. must be installed Most modern operating systems such as Microsoft Windows 95 Windows 98 Windows ME Windows NT4 and Windows 2000 along with most versions of Linux and OS 2 include these drivers as standard in the operating system hence no additional drivers are required for reading discs on these operating systems Windows 3 xx and MS DOS If you require the drive to be recognised by Microsoft Windows 3 xx or MS DOS you will need to install the MS DOS device driver It can be downloaded from our support web site http www sony com au support itp NOTE If using Windows 95 or later and you have previously installed the MS DOS device driver it is recommended that you disable or remove MS DOS device driver as it will decrease performance 2001 Sony Australia 9 USING THE DRIVE Front Panel SONY GO mr l Earphone Jack 2 Volume Control 3 Emergency Eject 4 On Busy LED 5 Disc Tray 6 Play Skip 7 Stop Eject Speed 10 Cc 4 5 6 7 Stereo mini jack for headphones and or powered speakers Control volume of earphone jack This control has no effect on rear panel audio output In case the Eject button isn t working insert a small paper clip into this hole to eject the tray Note Turn off the power before doing this manual ejection The On Busy LED will be flashing while the CD ROM drive is busy The user can open or close the disc tray by pressi
3. 6 Power ReguirementS ee nsescccisiesaaealcneestyonchicdungusesselcwaceriajacdevacssieatilsvassieuaicaives 16 Environmental Conditions 5 ccs hdc 0kdovansnencdeseaciadeaonacnansedanesaduantetaraidgeasisesacedien 17 Dimensions amp IMIASS cess asticsiatcahasdagontesetcsaesuniaeToscanteateaestae natianasispwadeusaientt 17 2001 Sony Australia 2001 Sony Australia 5 2001 Sony Australia WARNINGS amp PRECAUTIONS WARNING Possible voiding of Warranty Please be aware that cracked deeply scratched or other poor quality discs used in this drive may cause damage to the drive and or the data on the disc Such discs may break at high speed rotation If full care is not exercised in relation to this matter you may void the warranty of this product PRECAUTIONS Do not attempt to open the drive and service it Removing the cover may cause exposure to harmful laser beams and electrical voltages User is recom mended to get service by returning the defected drive back to the original vendor where the drive is purchased Use the original packing for transporting the drive or sending back for service The original packing were designed and tested to protect your drive under rough conditions Do not put this CD ROM drive in direct sunlight on heat units or near electrical appliances which draw large amounts of current Keep your discs clean Using soft dust free cloth to clear the surface of the disc Do not drop or jolt the drive
4. CD discs by their edges Do not touch the surface of the discs 7 The drive is designed to be incorporated into a computer based system or unit which has an enclosing cover Using the drive alone or in any other configuration is prohibited oe a a D Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure 2001 Sony Australia 3 CONTENTS Warnings and Precautions 7 Introduction 8 PATS oer au one jeciencenc N E E E E S 8 Software Requirements aici cas ctesdvencervedscarvscdevoulbauudceusaswsdomarsdisedeumnentoinesienced 9 Using the Drive 10 Front Panel sce nicsnsptrenttsindero nano samnactesetanlednegenasies nea nustiedgouatesesanasduaiennsc edeaes 10 Maximum Speed Choice function gees scars icntsasaedvasaxeelsssewadintoausaWadsancaansednte 11 Installing the Drive 12 System Requirements essensie a eia EE a ES 12 Hardware Installation ane nee eee ween nee ee en ay eer nent mea er tely nana tr tener 12 Connections amp Settings sisi seria cserubsatca soi eed sinacadsttauadenadsdairowestas sd aubigteasneeas 13 Connecting th IDE cable srsiusszsrgeseccans douse usaeussseecdeeacidstesskataccdausnneantapasieneas 14 Trouble Shooting 15 Specifications 16 Ca saa S A A E A 16 Performance opera nea Te REET never Tremere ne anne irei e ie riaa Tre teen tr tne ary 16 PTAC G EPEE ENESE AE AAEE E ANEA ES A AEE 16 ReaD e aE T ncetaouaaeeenabias 1
5. LY WITH OPTICAL the drive INSTRUMENTS VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEOFENET NICHT IN DEN STRAHL BLICKEN AUCH gt NICHT MIT OPTISCHEN INSTRUMENTEN Dieser Aufkleber befindet sich an ADVARSEL USYNLIG LASERSTR LING VED BNING SE IKKE IND I 1 A STR LEN HELLER IKKE MED OPTISKE INSTRUMENTER der Oberseite des Geh uses ADVARSEL USYNLIG LASERSTR LING N R DEKSEL PNES STIRR IKKE INN I STR LEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER VARNING OSYNLIG LASERSTR LNING N R DENNA DEL R PPNAD STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT AVATTAESSA OLET ALTTIINA N KYM TT M LLE LASERS TEILYLLE L TUIJOTA S TEESEEN L K IZ A C A D CN A CEN AD 2001 Sony Australia l ACKNOWLEDGMENTS amp TRADEMARKS All contents are subject to change at any time without notice No responsibility is assumed for its use nor for infringements of patents or other rights of third parties and no patent or license is implied hereby All trademarks are the property of their respective owners 2 2001 Sony Australia INFORMATION You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty covering this equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against
6. NOTE This manual is subject to change without notice CDU 5211 Series SONY SONY CDU 5211 Series CD ROM Drive User s Manual ion 1 Copyright 2001 Sony Australia Printed in Australia 2001 Sony Australia Owner s Record The model and serial numbers are located on the topside of the drive Record these numbers in the space provided below Refer to them whenever you call upon your sales representative regarding this product Model No Serial No WARNING To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only CAUTION The use of optical instruments with this product will increase eye hazard The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure This unit uses CD ROM discs with the following mark When you use this unit as an audio CD player use compact discs with the following mark CAUTION This label is located on the drive unit s LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM internal chassis ATTENTION Dieses Etikett befindet sich auf dem inneren RAYONNEMENT LASER EN CAS D OUVERTURE Giese das E NE PAS REGARDER DANS LE FAISCEAU aSSIS Ges Laurwerkes This label is located on the top of CAUTION INVISIBLE LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM OR VIEW DIRECT
7. cautions on page 7 of this manual 2001 Sony Australia 11 INSTALLING THE DRIVE System Requirements To ensure stable performance the following system specifications are recommended OS DOS 6 xx or higher Windows 3 1x 95 98 ME 2000 NT 4 0 OS 2 Warp 3 0 or higher Interface Vacant IDE interface connector NOTE To operate the drive using DOS 6 xx or higher you will need to install the DOS device drivers These are available for free download from our support web site http www sony com au support itp Hardware Installation Please refer to your PC s user manual and follow their guidelines for adding hardware components Always follow their anti static precautions 1 Set the Master Slave jumper on CD ROM rear panel refer to figure 1 2 Locate an empty drive bay and slide the CD ROM drive into the bay Secure with four screws 3 Connect the power supply cable to the CD ROM drive Ensure the pin definition of power connector is the same as shown in figure 1 4 Connect the 40 pin IDE ATAPI cable to the CD ROM drive according to the description in figure 1 Note Pin 1 on the cable is generally indicated by a red stripe along the edge of the ribbon cable 5 Connect the sound cable from the Analog Audio on the rear panel of CD ROM to your sound card if you have a sound card in your system 6 Follow you PC s user manual to re assemble your PC NOTE For optimum performance on Windows based systems the drive
8. e drive and operating system volume controls Are speakers turned on 2001 Sony Australia 15 SPECIFICATIONS General Host Interface Acceptable Formats Acceptable Media Types Acceptable Disc Diameters Performance Rotational Speeds Random access time Data Buffer Burst Data Rate Audio Earphone Output Front Line Output Rear Digital Output Reliability Error Rate MTBF Power Requirements Operation Max Sleep Average Voltage Requirements 16 ATA PI compliant CD DA CD Rom mode 1 CD Rom XA mode 2 form 1 amp form 2 CD I Ready Video CD MPEG 1 Karaoke CD Photo CD Enhanced CD CD extra I Trax CD CD Text and UDF CD Rom CD R CD RW 12 cm and 8 cm CD Rom Max 52X 7800 KB sec CD Rom Max 40X 6 000 KB sec 80 ms 128 KB Ultra DMA 33 3 MB sec DMA mode 2 16 6 MB sec PIO mode 4 16 6 MB sec 0 7 0 2 VRMS 33Kohms 1KHz Odb 0 7 0 2 VRMS 47Kohms 1KHz Odb 5 0 Vp p SPDIF Standard Mode 1 ECC on 10 12 Block Bit Mode 2 ECC off 10 9 Block Bit 70 000 POH 25 duty cycle 5V 1 0 amps 12V 1 5 amps 5V 0 03 amps 12V 0 01 amps 5V 5 and less than 100m Vp p ripple voltage 12V 10 and less than 200m Vp p ripple voltage 2001 Sony Australia Environmental Conditions Operating Non Operating Dimensions amp Mass Dimensions Weight 2001 Sony Australia SPECIFICATIONS Temp 5 C to 45 C Humidity 10
9. harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help o This CD ROM Drive Unit is classified as a CLASS 1 LASER PRODUCT LASER PRODUCT The CLASS 1 LASER PRODUCT label is located on the LASER KLASSE 1 PRODUKT top of the drive Safety Notice l Do not install or operate the product in high temperature humidity or dusty environment Do not attempt to open the cover to repair the product yourself Never spill liquid of any kind on the product Always follow instructions on this manual under operating the product To prevent exposure to laser emanations harmful to human eyes do not attempt to disassemble this unit Hold
10. he Slave Device on either bus if both of the Master Device possibilities have been taken by other devices Some devices such as CD writers and DVD drives may be required to be set as the Master Device in this case it is OK to set the CD ROM drive as the Slave Device Device 2 Slave Hard Disk Le a Master Device 1 Master Secondary IDE Bus Primary IDE Bus PC Mother Board Figure 2 14 2001 Sony Australia TROUBLE SHOOTING If you experience any trouble during installation or normal use of your CD ROM drive please refer to the following information You will find further information on our support web site http www sony com au support itp Symptoms Action Appears to have no power Check DC power cable connection Check IDE interface connections Check the MASTER SLAVE settings of all devices CD drive not recognised by system The disc tray will not open Disable the lock eject feature software of the operating system Shut power down and use emergency eject hole to eject disc Cannot read data on discs Check the surface of CD media always keep it clean and free from scratches Check the quality of CD media Check if other discs or music CD s are reading OK Is Disc inserted upside down Could disc be a UDF formatted disc Check if a UDF reader is installed No sound Check sound cable connections Check the volume settings of th
11. ng the Open Close button Will start playing of an Audio CD or Skip to next track if already playing an Audio CD Will eject the tray if a CD ROM is playing Will stop an Audio CD playing pressing it again will eject the tray as usual Pressing this button can also change the max drive speed The default max speed is 40X Press and hold for 5 seconds to change the drive speed from 40X to 52X Tray out disc will reset drive speed from 52X to 40X automatically 2001 Sony Australia USING THE DRIVE Maximum Speed Choice function The CDU 5211 has a Maximum Speed Choice function where the user can select between maximum speeds of 40X or 52X The drive always defaults to 40X To activate 52X operation press and hold the Stop Eject button for 5 seconds The drive will then read the current disc at 52X speed When the disc is ejected the drive will default back to 40X operation It is recommended that 52X operation only be activated under the following conditions You are confident that the disc been used is in good condition and free from marks and scratches The disc is well balanced and does not have thick printed ink or adhesive labels attached to its surface The disc is not physically damaged in any maner Discs that have the above characteristics may reduce maximum transfer speeds due to excessive disc vibration at 52X NOTE Physically damaged discs may void warranty refer to Warnings amp Pre
12. s DMA setting in the device manager should be enabled Refer to your Systems help menu for assistance 12 2001 Sony Australia INSTALLING THE DRIVE Connections and Settings There are three pairs of jumpers MA Master SL Slave and CS Cable Select on the rear panel of your CD ROM drive Figure 1 shows the location of each jumper Rear of Drive Cable Select Digital Analogue Slave Audio Audio Master HOST INTERFACE POWER CS M SO DC RCCL SLA 40 2 5 G G 12 ecco Master Device Slave Device Factory default setting Figure 1 CS CSEL If your system supports the CS setting you can set the jumper to the CS position The Master Slave setting will then be made automatically depending on your hardware Configuration No jumper is then required on the MA or SL pins 2001 Sony Australia 13 INSTALLING THE DRIVE Connecting the IDE cable Most PC systems can connect up to 4 devices on the IDE ports Your PC should consist of a Primary IDE Bus and a Secondary IDE Bus each of which can have two devices connected to it a Master device and a Slave device Refer Figure 2 In most PC systems the hard disk drive is set as the Master Device on the Primary IDE Bus this should not be altered If available it is recommended that you connect the CD ROM drive as the Master Device on the Secondary IDE Bus The CD ROM drive can also be set as t
13. to 80 RH Altitude 0 3 500 m Temp 35 C to 60 C Humidity 10 to 90 RH Altitude 0 12 500 m 145 8 x 41 3 x 190 mm WxHxD 0 5mm 0 9Kg 17
Download Pdf Manuals
Related Search