CPE RELAY CARD USER`S MANUAL
Contents
1. POWER TECHNOLOGIES CPE RELAY CARD USER S MANUAL The CPE Relay Card is a UPS management product with 5 relay contacts for monitoring the status and 1 input contact to shutdown the UPS Qualified Service Personnel must perform the installation and servicing of this equipment MINUTEMAN accepts no liabilities and is not limited to injury to the Service Personnel or damages to the UPS or the connected equipment caused by the incorrect installation or servicing of this CPE Relay Card Installation Procedure of the CPE Relay Card NOTE The CPE Relay Cards are designed to be Hot Swappable but there is a remote chance that when Hot Swapping the CPE Relay Card that the UPS will shutdown MINUTEMAN recommends following steps 1 through 9 when installing the CPE Relay Card but to hot swap skip to step number 3 and omit steps 7 8 1 Turn off all the equipment that is plugged into the UPS 2 Turn off the UPS and unplug the UPS s power cord from the AC wall outlet 3 Remove the Option Slot cover plate from the rear panel of the UPS 4 Insert the CPE Relay Card into the option slot 5 Install the appropriate cover plate and secure with the retaining screws 6 Connect the monitoring cable to the terminal block port on the CPE Relay Card 7 Plug the UPS s power cord into the AC wall outlet and turn the UPS on 8 Turn on all the equipment that is plugged into the UPS 9 The installation of the CPE Relay Card is c2. may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL PARA SYSTEMS BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically Para Systems is not liable for any costs such as labor for on site installation on site maintenance or on site service lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data cost of substitutes claims by third parties or otherwise The sole and exclusive remedy for breach of any warranty expressed or implied concerning Para Systems products and the only obligation of Para Systems hereunder shall be depot repair or replacement of defective equipment components or parts or at Para Systems option refund of the purchase price or substitution with an equivalent replacement product This warranty gives you specific legal rights and you may also have other rights which vary from state to state No employee salesman or agent of Para Systems is authorized to add to or vary the terms of this warranty 34000399 R2
3. omplete CPE Relay Card Terminal Block Pin out 1 UPS Shutdown Input Signal return 2 UPS Shutdown Input Signal positive 3 Common relay connection for pins 6 through 10 4 ENE e al at Low Battery Warning Inverter On Normally open relay contact that closes when the inverter is operating a AC Normal Normally open relay contact that closes when the AC is normal Utility Failure Normally open relay contact that closes when the utility fails 10 Bypass Active Normally open relay contact that closes when the UPS is in the Bypass mode Note Apply 6 25VDC between pin1 and pin2 for 5 seconds to shutdown the UPS The relay s contacts are rated for 40VDC 25mA Obtaining Service 1 Call your dealer for assistance If you cannot reach your dealer or if they cannot resolve the problem call or fax MINUTEMAN Technical Support at the following numbers Phone 972 446 7363 Fax 972 446 9011 or visit our Web site at www minutemanups com Please have the following information available BEFORE calling the Technical Support Department Your name and address Where and when the unit was purchased All of the model information about your relay card Any information on the failure A technician will ask you for the above information and if possible help solve your problem over the phone In the event that the unit requires factory service the technician will issue you a Return Material Authorization Numbe
4. r RMA f Ifthe relay card is under warranty the repairs will be done at no charge If not there will be a charge for repair 2 Pack the relay card in its original packaging If the original packaging is no longer available ask the Technical Support Technician about obtaining a new set It is important to pack the relay card properly in order to avoid damage in transit Never use Styrofoam beads for a packing material a Include a letter with your name address daytime phone number RMA number a copy of your original sales receipt and a brief description of the problem 3 Mark the RMA on the outside of all packages The factory cannot accept any package without the RMA marked on the outside 4 Return the relay card by insured prepaid carrier to Dapp Para Systems Inc MINUTEMAN UPS 1809 W Frankford Road Suite 150 Carrollton TX 75007 ATTN RMA Limited Product Warranty Para Systems Inc Para Systems warrants this equipment when properly applied and operated within specified conditions against faulty materials or workmanship for a period of three years from the date of purchase For equipment sites within the United States and Canada this warranty covers depot repair or replacement of defective equipment at the discretion of Para Systems Depot repair will be from the nearest authorized service center The customer pays for shipping the product to Para Systems Para Systems pays ground freight to ship the produc
5. t back to the customer Replacement parts and warranty labor will be borne by Para Systems For equipment located outside of the United States and Canada Para Systems only covers faulty parts Para Systems products that are depot repaired or replaced pursuant to this warranty shall only be warranted for the unexpired portion of the warranty applying to the original product This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase The warranty shall be void if a the equipment is damaged by the customer is improperly used is subjected to an adverse operating environment or is operated outside the limits of its electrical specifications b the equipment is repaired or modified by anyone other than Para Systems or Para Systems approved personnel or c has been used in a manner contrary to the products User s Manual or other written instructions Any technical advice furnished before or after delivery in regard to use or application of Para Systems equipment is furnished without charge and on the basis that it represents Para Systems best judgment under the circumstances but it is used at the recipients sole risk EXCEPT AS PROVIDED HEREIN PARA SYSTEMS MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation of implied warranties therefore the aforesaid limitation s
Download Pdf Manuals
Related Search