Quick Guide - Hjaltland Housing Association
Contents
1. D Back button Control knob Switch A Display Instructions settings and operational information are shown on the display The easy to read display and menu system facilitates navigation between the different menus and options to set the comfort or obtain the information you require B Status lamp The status lamp indicates the status of the heat pump It E fights green during normal operation lights yellow in emergency mode E light red in the event of a denloved alarm C OK button The OK button is used to confirm selections of sub menus options set values page in the start guide D Back button The back button is used to go back to the previous menu change a setting that has not been confirmed Control knob The control knob can be turned to the right or left You can scroll in menus and between options increase and decrease the values change page in multiple page instructions for example help text and service info Switch The switch assumes three postions On i Standby OQ Emergency mode Emergency mode must only be used in the event of a fault on the heat pump In this mode the compressor switches off and the immersion heater engages The heat pump display ts not illuminated and the status lamp illuminates yellow Hjaltland Housing Association Ltd Setting the Indoor Climate House Temperature Your house temperature is set by Outdoor temperature Indoor temperatu2. When it is time to clean an alarm indication occurs is displayed This will happen every three months To clean the filters you must 1 Setthe switchto gi 2 Remove the upper front cover by pulling it straight out 3 Pull out the filter cassette 4 Take out the filter and shake vacuum off any dirt Do not use water or other liquids for cleaning 5 Check the filter is not damaged 6 Carry out assembly in reverse order Even if the filter appears clean dirt collects in it and this affects the efficiency of the filter Please read the manufacturers user manual for further information on maintenance of your heat pump Hjaltland Housing Association Ltd Using Your Nibe F470 Heat Pump Generally The instructions listed previously are for setting the house and hot water temperatures only There is however a lot more options available to you via the display unit on the front of the heat pump These include the ability to set heating ventilation and hot water schedules Scheduling Heating gives you the sa Pi m ability to increase or decrease the indoor temperature for up to three time periods a day for example if you want to turn the heating down when you are out of the house whilst at work you can do this by accessing the scheduling heating menu See the user manual for further instructions Please remember your heat pump requires the indoor temperature to be at least 16 to operate efficiently 7
3. G ai mon tues wo fur ti sx oun Day Time penod Adjusting scheduling Ventilation gives you the ability to increase or decrease the ventilation in your property for up to two time periods a day The correct amount of ventilation for your property is achieved on the normal normal 60 setting for ventilation so you do not speed 1 0 need to do anything further unless gt speed 2 40 you want to increase the level of yn ventilation See the user manual for _J speed 4 100 further instructions Scheduling Hot Water gives you the ability to increase or decrease the temperature of the hot water for up to two time periods a eo uu day Your heat pump is set to the Normal setting and should not require any further adjustment unless you wish to set specific days and times for the water temperature to increase or decrease See the user manual for further oy rmeperoa asusin instructions Hjaltland Housing Association Ltd Using Your Nibe F470 Heat Pump Generally Advanced Settings is available in the indoor climate hot water and heat pump menus This option is for advanced users and we would ask that you do not change any settings within this menu unless you are fully aware of the outcome of any adjustments Changes within this menu might result in increased running costs Information on the heat pump is available via the Info menu There are several sub menus No settings can be ch
4. all times Hjaltland Housing Association Ltd Controlled ventilation with heat recovery reuses the heat energy in the exhaust air taken from wet rooms such as kitchens bathrooms We s etc It uses this energy to provide the heating and hot water for your property The heat pump in your property has been commissioned to work at an 2N ee optimum level and therefore a o gt Reger only requires minor 3 To adjustment to suit your needs This can be done by accessing the Menu System on the display unit Display unit A Display 5 Status lamp m gt OK button nse fo N ry SS TTT L Back button I Control knob Saoil The temperatures are only examples and may vary between different installations and time STL i of year F Switch Using Your NIBE F470 Exhaust Air Heat Pump Listed below is some basic information on controlling your heat pump Please read the user manual included in your tenant pack carefully to ensure you are familiar with the controls of the heat pump The display unit behind the heat pump door is used to e Switch on switch off or set the heat pump in emergency mode e Set the indoor climate house temperature and hot water temperature e See different types of alarms and receive instructions about how they are to be rectified Hjaltland Housing Association Ltd Display unit f Poa Fa D Display B Status lamp C OK button OK y
5. Hjaltland Housing Association Ltd A Quick Guide to Using Your NIBE F470 Exhaust Air Heat Pump en _waal en lt Hjaltland Housing Association Ltd How do exhaust air heat pumps work An exhaust air heat pump uses the heat that s in the building s ventilation air to heat up the accommodation The exhaust air heat pump in your property not only Supplies all your heating House with exhaust air and hot water Supplier air system and NIBE F470 requirements it also has a controlled ventilation system with heat recovery which ravides the necessary air changes in your home Nowadays we spend around 90 of the time indoors This undoubtedly places great demands on the climate inside The inside climate is affected considerably by odours moisture noise temperature etc It is therefore important to have the correct level of ventilation to stop any damage which may occur due to excessive moisture lack of heat etc In every building there is a certain amount of basic ventilation produced by air coming through windows doors pipe ducts etc This type of ventilation in older houses provides the necessary exchange of air This property has been designed and constructed with enhanced insulation and draught proofing measures to prevent heat escaping and make your home more energy efficient We cannot therefore rely on the natural air changes to provide the correct level of ventilation and must have the heat pump on at
6. anged in these menus it is just the display of information Outdoor tenoemtum indoor temperature roan sensors am retaled information about open bar Tenoomry bux f Estrmated smout of acti wa ted hot wa ler The Heat Pump menu has several sub menus Through these menus you can change the language time amp date visible icons etc See the user manual for further instructions This guide is meant as a quick introduction to using your heat pump The Association strongly advise you to read the manufacturers user manual to familiarise yourself with the options available for heating and hot water
7. b and OK button to take you into comfort mode the Comfort Mode 2 2 page You can now scheduling choose the setting you require using the advanced control knob and OK button The heat pump in your property is set to Normal as we recommend this setting for your house type The Economy mode gives less hot water than the others but is more economical This mode is used in smaller households with a small hot water requirement The Normal mode gives a larger amount of hot water and is suitable for most households The Luxury mode gives the greatest possible amount of hot water In this mode the immersion heater as well as the compressor is used to heat hot water which may increase operating costs Note U In Lux mode the heat pump prioritises hot water before room heating Hjaltland Housing Association Ltd Boosting the Hot Water Temporary Lux To temporarily boost the amount of hot water highlight the hot water menu water droplet using the control ii aa ei Wa knob and then press the OK button This will take you to the Hot Water 2 menu Select the Temporary Lux option using a rotate the control knob and OK button to take you into the Temporary Lux 2 1 page temporary lux Navigation comfort mode I a Ok button confirm select OR TA os f 4 Back button back undo exit scheduling VS Control knob move increase reduce advanced On the Tempo
8. diators on the first floor where applicable The underfloor heating can be controlled by individual room thermostats where applicable and the radiators with thermostatic valves which allow you to control the temperatures in each room An increase in the room temperature can be slowed by the radiator thermostats so it is advised _ to open the valves fully in the first instance then Ken amp Ee adjust to suit thereafter It should be noted that due to the low temperatures involved with this type of b heating system your radiators will never get really g lt j hot and have been sized to allow for this Hjaltland Housing Association Ltd Setting the Hot Water Capacity Hot water Temperature Your hot water is supplied via the heat pump and has three settings Economy Normal amp Luxury iilii 0t water temp Outdoor temperature Indoor temperature if room sensors are installed The difference between the selectable modes economy normal amp luxury is the temperature of the hot tap water Higher temperature means that MEAT PUMP the hot water lasts longer Information about operation Temporary lux if Estimated amount of activated hot water You can access these settings by highlighting the hot water menu water droplet using the control knob and then press the OK button This will take you to the Hot Water 2 menu Select the Comfort Mode option using the temporary lux control kno
9. rary Lux 2 1 page you have the option of boosting the hot water for three six or twelve hours The boost is activated immediately when a time period is selected and confirmed using the OK button Please note that when you select the Temporary Lux option you are asking the heat pump to increase the hot water temperature to the Luxury setting for the time period requested In this mode the immersion heater as well as the compressor is used to heat hot water which may increase operating costs Hjaltland Housing Association Ltd Maintenance of your Heat Pump All servicing must be carried out by a competent person Hjaltland Housing Association will arrange for an annual service of your heat pump There is however some minor tasks and checks to carried out by the user Cleaning the Ventilation Devices The ventilation system has been balanced This involves adjusting the extract and supply terminals to ensure the correct flow rates are achieved Your properties ventilation outlets in the ceiling should be cleaned regularly with for example a small brush to maintain the correct ventilation flow rates The outlets must not be adjusted as this will put the DI NATT system out of balance H o EDN Cleaning the Air filters Your heat pump has two air filters located behind the top panel of the unit The filters need to be cleaned regularly how often depends on the amount of dust in the ventilation air
10. re if room sensors are installed accessing the Indoor climate menu Your property has been fitted N Hot water temp with a room sensor so the display will show you the actual indoor and outdoor temperatures at the time of viewing Infomation about operation Within the Indoor Climate menu there are HEAT PUMP sub menus Select the Temperature nemini Bidian option from the sub menus A picture ofa diii single thermometer will then appear with a temperature Display box The indoor temperature of your property can be adjusted by using the control knob to set the desired temperature in the display box and then click OK temperature e fitis warm outdoors and the room temperature venigiston is too low increase the value in the temperature scheduling Display box by one increment iE e fitis warm outdoors and the room temperature is too high reduce the value in the temperature Display box by one increment When adjusting the indoor temperature please wait 24 hours before making a new setting so that the room temperature has time to stabilise Caution Your heat pump requires the indoor temperature to be at least 16 C to operate efficiently The electric immersions will activate when indoor temperatures are below the minimum Please be aware of this when adjusting the indoor temperature setting Your property is fitted with under floor heating on the ground floor and ra
Download Pdf Manuals
Related Search