F45078I-M - Eurohome Kitchens and Appliances
Contents
1. pressing start pause ref 2 fig 2 02 The pro gram will resume from where it was interrupted If the temperature in the tray exceeds 50 C 122 F the program will resu me after about 30 seconds CI If you open the door while the appliance is working you must close it and 2 2 3 End of program The end of the program is signaled by a short beep Additionally the indicator light of the daily wash and extreme wash programmes marked end flashes 2 2 4 Interrupting a program To interrupt the current program press the start pause button ref 2 fig 2 02 the indicator light of the current program remains on confirmation beep at this point start the cycle by pres sing start pause ref 2 fig 2 02 or change or cancel the program 2 2 5 Changing the current program To change the current program interrupt it see para 2 2 4 Interrupting a program select a new program see para 2 2 2 Selecting and stating a program Rev 0 0 11 USER INSTRUCTIONS 2 2 6 Canceling the current program To cancel the program press start pause ref 2 fig 2 02 until it stops indicator light on and beep Press start pause ref 2 fig 2 02 once again and hold it down until the indicator lights of programs four and five ref pr 4 pr 5 fig 2 03 marked end light up The water in the tray is drained and the program terminates at the point where it was stopped Fig 2 03 2 2 7 Options2. water softener tank to add salt see the instructions in the general manual The correct amount of detergent has been added to the dispens er to add detergent see the instructions in the general manual The spray arms are able to rotate freely and without obstruction The racks have been correctly loaded see the instructions in the general manual The dishwasher door is securely closed 2 2 1 Switching on Press on off ref 1 fig 2 02 to start the dishwasher the indicator lights show the status of the dishwasher 2 2 2 Selecting and starting the program Programming operations can only be performed with the door closed cy With the door open the program indicator lights ref 4 fig 2 02 remain off Press the program selection button ref 3 fig 2 02 several times until the indi cator light corresponding to the required program turns on ref 4 fig 2 02 if necessary press the relative buttons to select the complementary functions you wish to use e g Programming delay to start the dishwasher press the start pause button ref 2 fig 2 02 for a few seconds until the indicator light of the selected program starts flashing con firmation beep Program status is indicated by the indicator light flashing throughout the cycle If the door of the dishwasher has not been closed or has been incorrectly closed the washing cycle will not begin 10 Rev 0 0 USER INSTRUCTIONS start the program again by
3. 3t JE imp yx ctu Fig 2 04 2 3 Additional functions 2 3 1 Adjusting the water softener The dishwasher is fitted with an water softener which can be adjusted according to the hardness of the water Depending on the model involved the adjustment switch can be inside the plastic ring nut on the right hand side ref A fig 2 05 inside the dishwasher inside the water softener just under the cover ref B fig 2 05 Both can be adjusted to 6 positions 14 Rev 0 0 USER INSTRUCTIONS Fig 2 05 Water hardness table see tab 2 03 WATER HARDNESS A American degrees SETTING German degrees D French degrees F grains gallon 0 4 0 7 0 4 5 N 1 NO SALT 5515 8 25 4 6 14 5 NR 1 16 23 26 40 14 6 23 5 NR 2 24 31 41 60 23 6 35 NR 3 32 47 61 80 35 1 46 5 NR 4 48 58 81 100 46 6 58 5 NR 5 Tab 2 03 Contact your local water board for information on the hardness of your water supply Rev 0 0 15 USER INSTRUCTIONS 3 ENERGY SAVING AND ENVIRONMENTAL RESPECT Always try to run the dishwasher fully loaded Do not wash the dishes under a running tap Use the most suitable washing program for each type of load Do not pre rinse If available connect the dishwasher to a hot water system with a temperature of up to 60 C 140 F 3 1 Reducing the consumption of detergent and respecting the envir
4. F45078l M Dishwasher Lave vaisselle User manual Manuel d instructions mio AEG oO PERFEKT IN FORM UND FUNKTION amp Electrolux CONTENTS Contents 1 INTRODUCTION En nent ee o eiia iatan Yr laika 5 2 DESCRIPTION AND USE OF THE CONTROLSG esssssssseccssessseccsssecseesseecnseesseecnseessseense 7 2 1 Front panel 22 Setting the washing program and switching on and off 8 2 2 1 Switching OD Essen a A E 10 2 2 2 Selecting and starting the program rennes 10 2 2 3 Enid Of POCA etr O O ER AN en 11 2 2 4 Interrupting a LOGAN asscissscssssecinsscscsusconsoastansci ssaveosssnsennsvistconeissetsacssdlenssbasaesanssiberstesedetenesd 11 2 2 5 Changing the current program nine 11 2 2 6 Canceling the current program 12 2 2 7 OPTIONS NA LLL LL 12 2 2 8 Switching ff ccrte terrier a A RE EAU a 14 2 3 Additional FUNETIONS ses tta eter ebrei geben bebe PHP REOR CUPIS RS 14 2 3 1 Adjusting the water softener nes 14 3 ENERGY SAVING AND ENVIRONMENTAL RESPECT ne 16 3 1 Reducing the consumption of detergent and respecting the environment 16 4 REMOVING THE DISHES eitis obses etre ert pert bb dtes opi teh 17 5 TROUBLESHOOTING c 18 Rev 0 0 Rev 0 0 1 Rev 0 0 INTRODUCTION INTRODUCTION Thank you for choosing one of our products To use this dishwasher cor rectly and safely please read this manual carefully The manual is divided into secti
5. GO PROGRAM DELAY The Program delay function delays the beginning of the washing program by 3 6 or 9 hours from the moment in which programming takes place This makes it possible to use the dishwasher at a certain time of day Before programming a delay select the reguired washing program see para 2 2 Setting the washing program and switching on and off Select the delay by pressing the program delay button ref 6 fig 2 02 in seguen ce depending on the delay you wish to set the corresponding indicator light will shine ref 7 fig 2 02 The dishwasher will perform a pre wash cycle after which the preset program delay will commence the indicator light ref 7 fig 2 02 corresponding to the time remaining before the program starts and the indicator light ref 4 fig 2 02 indicating the set program start flashing 12 Rev 0 0 USER INSTRUCTIONS To cancel or change the delay of a program once it has begun press the start pause button ref 2 fig 2 02 for a few seconds until the pro gram delay indicator light ref 6 fig 2 02 and the set program indicator light ref 4 fig 2 02 stop flashing and remain lit press the delay program button ref 6 fig 2 02 to modify or cancel the set delay indicator lights 3 5 8 fig 2 02 off press the start pause button ref 2 fig 2 02 to start the program If a delay is set the program delay indicator light ref 7 fig 2 02 and the set program indicator light ref 4
6. ROGRAM MTS ee POWER AND SYMBOL CUTLERY SEQUENCE a Kim PANS AND DISHES WAITING ij RINSE m FORTHE Cold pre wash 16 lerdal 0 03 iy LOAD TO BE 24987 COMPLETED Wash at 45 C E 113 F SLIGHTLY DIRTY Cold rinse 13 71 CRISTAE DISHES Rinse at 69 C 66 3 62 gal Re Y 156 2 F Dry SLIGHTLY DIRTY HA JOE O PANSAND 22 P NORMAL DISHES BUT Cold rinse 110 TA 0 8 V WITH DRIED ON e ilo RESIDUE p Cold pre wash DIRTY PANS nese 656 DAILY AND DISHES 9 rinse T 18 21 en WASH WITH DRIED ON nrc 48 gal B RESIDUE 156 2 F Dry Pre wash at 45 C 113 F EXTREME VERY DIRTY A s 70 C ETLSANITATION 7 DRIED ON us 38 gal LISTED RESIDUE seer Dry Tab 2 02 1 The cycle times listed in the use and care manual are based on normal soil loads and 120 F 49 C incoming water and will vary based on your actual conditions Only EXTREME WASH program conform to NSF std 184 and is certified by INTERTEK with the ETL SANITATION LISTED When the Sanitized light shine it means that the dishwasher and its contents have been sanitized according to the requirements of the National Sanitation Foundation NSF Rev 0 0 9 USER INSTRUCTIONS Only run a soak program with half loads After using the above table to choose the most suitable washing cycle program the appliance Before starting a washing program make sure that e The water supply tap is open e There is regenerating salt in the
7. art If the problem persists contact the technical assistance service Alternate washing system malfunction n o o 3t Interrupt the current program and switch off the E8 x dishwasher Switch it back on again program a new fy Y Z a LE cycle and press start If the problem persists contact the technical assistance service iT E9 Ens de Water intake system malfunction AS v g a O Contact the technical assistance service Tab 4 01b Ll Light off M Light on 3t Light flashing If an alarm situation occurs the dishwasher interrupts the current program and signals the fault Alarms ET E2 E3 E4 E8 E9 immediately terminate the current program Alarms E5 E6 interrupt the current program and after the problem has been eliminated resume the cycle Alarm E7 is displayed at the end of the cycle which however is completed given that it does not jeopardize dishwasher operation To reset an alarm open or close the door or switch the appliance on and back off again At this point the dishwasher can be programmed again If the fault persists contact the Authorized Technical Assistance Service Rev 0 0 19
8. fig 2 02 begin flashing if the program delay is cancelled only the program indicator light ref 4 fig 2 02 flashes to show that it has started To enter the delay when the program has already begun proceed as follows If the program to runis the same as the current one press start pause ref 2 fig 2 02 and hold it down for a few seconds until the indicator lights of programs four and five ref pr 4 pr 5 fig 2 03 marked end light up cancel the current program see section 2 2 6 Canceling the current program and wait for the cycle to finish select the program once again select the required delay press the start pause button ref 2 fig 2 02 to start the program If the program to run is different from the current one press start pause ref 2 fig 2 02 and hold it down for a few seconds until the indicator lights of programs four and five ref pr 4 pr 5 fig 2 03 marked end light up change program select the required delay press the start pause button ref 2 fig 2 02 to start the program The dishwa sher will drain and continue with the required delay and the new program Rev 0 0 13 USER INSTRUCTIONS 2 2 8 Switching off At the end of the program the dishwasher emits a short beep and the indicator lights of the fourth and fifth program ref pr 4 pr 5 fig 2 04 flash Press the on off button ref 1 fig 2 02 to switch off the dishwasher 4 5 EN O o 0
9. on and warnings which if not observed may compromise personal safety or damage the appliance This symbol highlights general information and warnings Tab 1 01 6 Rev 0 0 2 2 1 USER INSTRUCTIONS DESCRIPTION AND USE OF THE CONTROLS Front panel All the dishwasher controls are grouped on the front panel see fig 2 01 A brief description see tab 2 01 of the various elements on the front panel is given below Fig 2 01 On Off button Start Pause button Program selection button Program indicator lights Sanitation indicator light Program delay button Program delay indicator lights CO N A W A WIN Recessed door handle Tab 2 01 Rev 0 0 USER INSTRUCTIONS 2 2 Setting the washing program and switching on and off The dishwasher is equipped with a control panel see fig 2 02 which is used to program the appliance and switch it on and off 5 7 4 AEG m e PISO P CA m 1 6 32 Fig 2 02 To select the most suitable program for the dishes to wash consult the following tables which specify the most appropriate type of washing sequence depending on the kind of dishes and how dirty they are see tab 2 02 8 Rev 0 0 PROGRAM NUMBER DISHES AND P
10. onment The phosphates contained in dishwasher detergents are harmful to the environ ment To avoid using excessive amounts of detergent and to save on electricity Separate the more delicate items from those that are more resistant to aggres sive detergents and high temperatures Do not pour the detergent directly onto the dishes 16 Rev 0 0 4 AN Rev 0 0 USER INSTRUCTIONS REMOVING THE DISHES Atthe end ofthe washing program wait at least 20 minute before remov ing the dishes in order to allow them to cool To prevent any water droplets on the upper rack from falling onto the dishes in the lower rack empty the lower rack first and then the upper one 5 USER INSTRUCTIONS TROUBLESHOOTING The dishwasher can signal a number of malfunctions by turning on various indi cator lights as described below see following table FAULT DESCRIPTION E1 pe D Acquastop failure The anti flooding system has tripped Activates in case of water leaks Contact the technical assistance service E2 c a Q Safety level The system limiting the water level in the dishwasher has tripped Interrupt the current program and switch off the dishwasher Switch it back on again program a new cycle and press start If the problem persists contact the technical assistance service E3 qi c a Q Water heating malfunction The
11. ons giving you a step by step guide to all your appliance s func tions The texts are easy to understand and are complete with detailed illustrations This user friendly manual will provide answers to all your questions about use of the dishwasher Before using this dishwasher carefully read chapter 2 Use and safety warnings of the attached general manual For any other information about use and maintenance of the dishwasher read the enclosed general manual carefully This manual comprises the following sections INTRODUCTION general information about the manual USER INSTRUCTIONS advice on using the washing programs and infor mation about all the dishwasher functions Nomenclature of figures and tables The progressive number of each figure is shown in the bottom right hand corner of the relative box An example of a progressive number is Fig 4 01 where the first number 4 indicates the section to which the figure belongs while the second number 01 indicates the progressive number ofthe figure in section 4 Fig 4 01 is the first figure in section 4 The tables are numbered in the same way bearing in mind that Tab is used instead of Fig e g Tab 4 01 is the first table in section 4 If a table occupies more than one page a letter is added after the progressive number e g Tab 4 0Ta Tab 4 01b INTRODUCTION Symbols used in this manual see tab 1 01 DANGER This symbol highlights informati
12. water is not heated or is incorrectly heated Repeat the washing program if the problem persists contact the technical assistance service E4 air Q Water temperature monitoring malfunction Interrupt the current program and switch off the dishwasher Switch it back on again program a new cycle and press start If the problem persists contact the technical assistance service E5 S KI x peer Water intake malfunction The appliance does not take in water or does so incorrectly Make sure the water connections are correct that the water supply tap is open and that the filter is not clogged If the problem persists contact the technical assistance service E6 KI 5 pe a Q Water pump out malfunction The appliance does not pump out the water or does so incorrectly Make sure the drain hose is not kinked or crushed and that the siphon and filters are not clogged If the problem persists contact the technical assistance service Tab 4 01a 18 Rev 0 0 USER INSTRUCTIONS FAULT DESCRIPTION Turbine flow regulator malfunction EN The appliance is unable to precisely measure the Xt Xt JE RT quantity of incoming water Interrupt the current E7 ma program and switch off the dishwasher Switch HHY p y Y g O it back on again program a new cycle and press st
Download Pdf Manuals
Related Search