Owner`s Manual
Contents
1. ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D OUVERTURE EVITER TOUTE EXPOSITION AUX RAYONS Copyright Statement It is a criminal offense under applicable copyright laws to make unauthorized copies of copyright protected material including computer programs films broadcasts and sound recordings This equipment should not be used for such purposes I OMAGIC Corporation makes no warranty of any kind with regards to this material including but not limited to the implied warranties of merchantability and fitness for a particular product I OMAGIC Corporation shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing performance or use of this material Every effort has been made to ensure that the information in this manual is accurate Corporation is not responsible for printing or clerical errors Mention of third party products is for information purposes only and constitutes neither an endorsement nor a recommendation Corporation assumes no responsibility with regards to the performance of these products This document contains proprietary information which is protected by copyright see below The information contained in this document is subject to change without notice Trademarks Microsoft is a registered trademark of Microsoft Corporation Windows Windows XP 2000 Me 98 95 NT and their logos are trademarks of Microsoft Co2. e Using the Online Help Suggestions for Resolving Common Problems The following section describes common problems you may encounter along with some suggestions for resolving them You can find a detailed list of errors and additional updates from Nero s website at http www nero com My CD ReWritable Drive is not found by Windows XP 2000 98 95 If you are connecting the CD RW drive to the motherboard read this Make sure that there are no conflicts both primary and secondary IDE controllers are present and without yellow exclamations marks To check the status of your IDE controllers click on the Start button gt Settings gt Control Panel gt System gt Hardware for Windows 2000 gt Device Manager under the Hard Disk Controllers category Yellow exclamation marks on the IDE controllers mean that the device is not working properly not installed properly or have a resource conflict with another device Some retail versions of Windows 98 95 may not recognize some of the IDE controllers This can result in IDE devices such as CD ROM drives not being detected or disappearing from the PC There are several ways to correct the problems If the Primary or Secondary I DE controllers are not present read this Your controllers are not setup properly and you need to get a patch from your motherboard manufacture or check your BIOS setup and make sure that both onboard IDE controllers are enable 93 48x16x48 CD ReWritab
3. 1SO icon in the new compilation dialog window If you get the Nero Wizard click on Close Wizard If you have already opened Nero you can reach this dialog window through the icon for New Compilation 2 Miten on Label ie o O Stat 088 T Conima Pla Mudie E i Bead Aad co In EXTRA Mulltestan gak C Coninae u del eon 19 48x16x48 CD ReWritable Drive User s Guide A new blank compilation window will open Drag amp drop the files you wish to copy from the File Browser window onto the ISO Window Use the indicator on the bottom to determine how much data you will be burning and how much free space will be left on your blank media Fic Li Mem Dnm nom Help ae a ai 4 Tie 7 r UEH EIN 5 Now open the Write dialog The easiest way to do this is to click on the Write CD icon in the toolbar You will then go to the Write CD dialog box which will undoubtedly look familiar to you it is the same box which you saw for the creation of a new compilation only now the Burn property button is shown on the top Later i Daes sc Fern Free CD Hehe Wie Spend ee 5
4. ke i AD pl Copes m 20 48x16x48 CD ReWritable Drive User s Guide You will see several boxes of which some have already been selected All of the preferences may now be examined and changed if necessary From here you can select your burn speed and other settings If you are satisfied with your settings click on the Write button to begin burning your CD Brin Oo dee Label Dates T we Pe a Canon F asd A unm I Fina ih peii sig Harsbar of Cap 15 F BIUPPI Proni Hirn Note If you wish to create a CD ROM as a single session you must click on the Finalize CD box Do not click this box for a session of a MultiS ession CD unless it is the last session CD is write protected after this Now you may confirm by clicking on the Write button All of the selected steps will now be carried out in sequence including the burn process So that you can follow exactly what is happening a status window is displayed in which the individual steps are listed ll Nero should now begin caching files and burning your CD When successful will see the message burn process completed successfully at 48x 7200 KB s Mero Burning Rom E x d Burn process completed successtully at 48x 7 200 KB 73 Nero will eject your CD when finished and ask to save this
5. tab to set your copy speed and settings Click Copy once you are ready to copy rs Corie ahaa 26 5 6 48x16x48 CD ReWritable Drive User s Guide Nero should now begin caching files and burning your CD When successful will see the message burn process completed successfully at 48x 7200 5 Nero Burning Rom 1 x d Burn process completed successfully at 48x 7 200 KB s Nero will eject your CD when finished and ask to save this profile You can save if you wish to burn the same CD at a later time or discard it to complete the burn Congratulations you have successfully copied a CD Note Some CD s may not be able to copy due to copyright protections We do not endorse software piracy Only make backup copies of software that are license to you Saving Audio Tracks The tracks on your Audio CDs are in CDA format You can save these tracks onto 1 2 3 your system as WAV files To do this follow the instructions below Insert an Audio CD into the CD Rewritable drive From the main Nero Burning Rom window select CD Recorder from the toolbar Select Save Track from the drop down menu Use your mouse to select the audio tracks you want to convert to WAV format To select multiple tracks hold the Ctrl button while selecting with the mouse Make sure you choose browse with a path of where you want to save the tracks Press the Save button to
6. that contains data such as trying to add a CD ROM XA session to a CD that contains a CD ROM session A CD containing both formats is unreadable so you are not allowed to record the different session type The current CD contains a Session that is not closed Close the session before writing further data to the disc CD ROM drives can only read back one data track per session so avoid recording another data track in an open session The currently selected source CD ROM drive or CD recorder cannot read audio in digital format Reading audio tracks in digital format is not the same as playing the music Few CD ROM drives can read audio tracks in digital format The destination CD is smaller than the source There is not enough room on the recordable CD to copy the source CD Try recording to a blank CD Use 74 minute media instead of 60 minute media Some CDs cannot be copied due to the TOC overhead in CD recorders and also due to the calibration zone overhead See PCA in Glossary Error reading the Table of Contents TOC or Program Memory Area PMA from the CD Do not try and write to this CD It has serious problems and may have been damaged during a previous write If this is a CD RW media erase it and try again MSCDEX Errors Versions of MSCDEX prior to 2 23 had problems with filenames containing illegal characters If a directory contains a filename with an illegal character you can see all the files by doing a
7. DIR from DOS and can open the illegally 38 48x16x48 CD ReWritable Drive User s Guide named file however one or more files listed after the illegal one may not be accessible or give errors The selected CD track is longer than the image file The verify fails immediately because the source ISO 9660 image and the ISO 9660 track on CD are not the same size The selected CD track is shorter than the image file The verify fails immediately because the source ISO 9660 image and the ISO 9660 track on CD are not the same size The selected disc image file was not prepared for the current CD Write anyway This is not likely to produce a readable CD These errors occurs if you prepared the disc image file for a blank CD and are now trying to record it to a CD containing data or vice versa In either case you would write a CD that cannot be read at all because the CD addresses calculated for the disc image are wrong for this CD Other Program Messages The following is a list of other program messages you may encounter along with their descriptions Adding files to CD image As part of the process of preparing to record Nero Burning ROM is creating a database of the files to be written to CD The files in the data track list are checked on the hard disk for potential problems such as hard disk corruption and their length is computed in preparation for writing Generating ISO 9660 image file
8. Nero InCD you must first format a blank CD RW media disc Right click on the Nero InCD icon located in the system tray and select Format The InCD Wizard will appear Click Next to continue Inch Wizard ACKETWRITING St ARE learn iin hi Aller choosmg prar gingi pou well ehis bo we a COT dioc 3 lupe opp dek BoP rr Select your CD RW drive and click Next to continue InCD Wizard Click Next again to continue Inch Wizard JE PACKET WRITING 501 Dice Irfa ratar Status Thi dic discs ae TENE BoP Prob 29 48x16x48 CD ReWritable Drive User s Guide Select Normal to quickly format your CD RW media disc Inch Wizard Label InCDi LD Fw hair Veira Label carr agzmad lt Space carri bs uz Pd C Comp bebe F nal mqar aboot 40 70 nin quien shat EI min Shop zeck processing bra AHEAD cic E O a 2 LD F disc egaa Sec Forma vell 10 io 30 Tie used mun Flees epee ha re pocadaa once cacalas eri o compile 1 1 Farmating was successful 22 You can now use this disc like large Floppy d
9. ReWritable drive We sure that you will enjoy this product in the years to come This product is a high performance IDE interface CD RW drive implementing the ATAPI IDE standard interface The bundled CD RW Mastering Software gives you the ability to archive distribute or create your own CDs CD ROM XA CD Bridge Multi Session CD CD I and CD DA from your computer s desktop The CD ReWritable drive can automatically recognize the media placed in the drive whether a CD a CD R or a CD RW disc The application included allows you to read and pre master CD R or CD RW discs plus file system drag and drop for archiving data interchange and back up on both CD R and CD RW discs User friendliness is further enhanced as the CD ReWritable can be used as a PnP Plug and Play CD ROM drive for all PC operating systems such as Windows XP 2000 ME 98 95 and NT You can use the quick select buttons to manually control Music CDs without running any software programs A standard ANSI MMC multimedia command set is also featured The CD ReWritable drive supporting all writing modes extends operational versatility and CD formats CD DA CD ROM etc include CD UDF as standardized by OSTA Furthermore the erase function is supported for CD RW discs allowing repetitive use 48x16x48 CD ReWritable Drive User s Guide Specifications Interface Type Internal E IDE Enhanced IDE conforms to ATAPI Version 2 6 L
10. begin saving the tracks to your hard drive s sm 48x16x48 CD ReWritable Drive User s Guide Nero INCD Nero InCD is packet writing software that works together with your CD RW drive and CD RW media to help manage your workflow and share data from one computer to another By using InCD it is possible to write individual files onto a CD RW disc making it as easy to use as a floppy disk Drag and drop the files and folders directly from your file manager to record them To delete unwanted files just drag and drop them to the trash Nero I nCD Installation Follow the installation instructions carefully and step by step If you encounter a problem refer to the troubleshooting section on this manual os Svan Power on your computer Boot into Windows Insert the Nero Burning ROM installation CD into your CD ROM drive The CD will automatically run and the installation program will guide you through the entire installation process 5 Reboot your computer at the end of the installation pU Note If the installation program does not launch automatically follow these steps 4 Click on the Start button on the task bar and select Run 5 From the command prompt type D Setup exe Where D is your CD ROM drive Select I nCD from the list 6 The installation program will guide you through the entire installation 48x16x48 CD ReWritable Drive User s Guide Format CD RW Disc IE To use
11. on the plus sign next to the CD ROM icon until you see the name of your CD recorder Select it Click on the Properties button The properties dialog box for your drive opens Click on the Settings tab Deselect Auto Insert Notification Click on OK to close the properties dialog box Click on OK to close the systems properties dialog box 0 Restart your system as prompted E 17 7 48x16x48 CD ReWritable Drive User s Guide Nero Burning ROM Interface This is the screen that you ll get when you first start Nero Burn ROM i aj alel a EC Musa WT THAT 1 1 AIAT E3718412 T1529 2 THE 258052 6 From here you ll be able to do the following Burn disc images Make CD boot discs Create DOS MAC hybrid discs great for cross platform software developers Create UDF or UDF ISO file system discs Audio CDs with critical sound filters Mixed Mode CDs Support a wide range of CD Recorder drives CD copying Files Directories from HD to disc image CD Overburning 18 48x16x48 CD ReWritable Drive User s Guide Create Data CD 150 Follow the steps below to burn a Data CD We will leave all the options with their default settings For detailed information please refer to the Reference Chapter in the manual The manual is on the Nero CD in the form of an Acrobat document ME Start Nero Burning Rom Click on the CD ROM
12. profile You can save it if you wish to burn the same CD at a later time or discard it to complete the burn Congratulations you have successfully burned a data CD 48x16x48 CD ReWritable Drive User s Guide Create an Audio CD Burning an Audio CD using Nero is similar to burning a Data CD Follow the steps below to burn an Audio CD We will leave all the options with their default settings For detailed information please refer to the Reference Chapter in the manual The manual is on the Nero CD in the form of an Acrobat document Note You can burn your Audio CDs using two possible methods Track at Once and Disk at Once e Track At Once allows you to burn individual tracks on a CD one at a time This method allows you to burn tracks from different source CDs without having to save them to your hard disk first However you will not be able to use some features such as variable pause length CD text or indexing Disk at Once allows you to burn an entire CD all in one setting The CD Laser never stops burning between tracks This method is preferred if you are burning MP3 or WAV files directly from your hard drive You can set the pause length between tracks and write CD text This method is best for compilation CDs that do not have a 2 second pause between songs such as remix CDs ENSE Start Nero Burning Rom Click on the Audio CD icon in the new compilation dialog window If you get the Nero Wizard cli
13. whether this is the problem In some cases an upgrade is available which will resolve the problem The combination of CD brand and CD recorder can make a difference Use only good quality CD R or CD RW media Which Nero Releases supports Windows 2000 The first Nero release which supports Windows 2000 is Nero 4 0 8 3 To find out what version of Nero you have click on Help from the main Nero Burning Rom window and select About Nero You can update your version of Nero by going to www nero com Does Nero cause a problem if I update from Windows NT to Windows 2000 Yes because the Nero driver for Windows NT does not work under Windows 2000 Please uninstall Nero before you upgrade to Windows 2000 36 48x16x48 CD ReWritable Drive User s Guide Error Message Descriptions The following is a list of error Messages you may encounter along with descriptions and suggestions for resolving them See also the online help for a listing of additional error Messages Buffer underrun at sector CD writing is a real time process which must run constantly at the selected recording speed without interruptions The CD recorder s buffer is constantly filled with a reserve of data waiting to be written so that small slowdowns or interruptions in the flow of data from the computer do not interrupt writing This message indicates that for some reason the flow of data from hard disk to CD recorder was interrupted long enough
14. 8 CD ReWritable Drive User s Guide Driver Installation Windows 2000 Me 985 95 Installation There is no need to install any CD RW device drivers under Windows XP 2000 Me 98 95 and NT IME Turn on your PC to start up your Windows XP 2000 Me 98SE 95 Operating System Windows XP 2000 Me 98SE 95 will automatically detect the new drive and load the appropriate drivers for your CD ReWritable drive Note Refer to the troubleshooting section of this manual if Windows does not automatically detect your CD ReWritable drive DOS or Windows 3 1x Installation Note Dos and Windows 3 X do not support CD writing You can ONLY use this device as a regular CD ROM drive Visit our website for Dos Windows 3 X drivers and information Windows NT 4 0 Installation IME Power on your PC Log into Windows NT Once in the desktop click on the Start button gt Settings gt Control Panel gt Devices Select ATAPI from the list and click on the Start up button SEE When you get the start up screen check Boot then click the OK button uM Repeat the same procedure with CD ROM steps 4 and 5 yam Close the Devices screen and click on the Start button gt Shut Down and restart the computer 14 48x16x48 CD ReWritable Drive User s Guide Nero Burning ROM The bundled Mastering Software gives you the complete solution for mak
15. A disc image is being written to hard disk because write on the fly is deselected or write disc image is selected in the general tab 39 48x16x48 CD ReWritable Drive User s Guide The CD recorder s laser is calibrated and the CD is checked in preparation for writing If there are no problems writing begins immediately Loading files from previous track to make linked multi Session This message appears when you choose to make a linked Multi Session CD During this process the ISO 9660 file system information is loaded from the track you chose in the load contents tab so that it can be linked with the new files to be recorded The ISO 9660 disc structure is prepared on hard disk This generates a large temporary file in your set temporary directory Using the Online Help You will find most of the information you need to use Nero Burning ROM in the Manual folder within the Nero Burning ROM CD Also you can open the Nero Burning ROM program and go to the Help Topics from the Help menu to get started More information and help with Nero can be found at www ahead de 40 48x16x48 CD ReWritable Drive User s Guide Limited Warranty Hardware Limited Warranty This product is warranted to be free from failures due to defects in material and workmanship for one year from the date of original purchase as evidenced by a copy of the purchase receipt During the warranty period OMagic at its sole discretion will
16. CD ReWritable USER S Manual 48x16x48 CD ReWritable Drive User s Guide Dear Customer Congratulations on the purchase of your CD ReWritable drive We all want to express our sincere gratitude for your decision to purchase our product and to reaffirm our commitment to you of providing a product that is easy to install and easy to use You can be assured that your new product is made from the latest state of the art components and that it has also gone through the most rigorous testing and quality assurance procedures in the industry With an emphasis on products that revolutionize the way people interact with the new technologies around us we continually introduce integrated solutions that enable users to take full advantage of their multimedia experience Our ever expanding product line covers the entire multimedia spectrum Look to us to as the leader of providing media products ranging from sound and graphics cards to DVD and CD ROM drives and even to digital imaging and mp3 audio products We hope you enjoy using your new product and look forward to earning your business in the coming years 48x16x48 CD ReWritable Drive User s Guide CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GE FFNET NICHT DEM STRAHL AUSSETSEN
17. cess completed successfully at 48x 7 200 KB s Nero will eject your CD when finished and ask to save this profile You can save it if you wish to burn the same CD at a later time or discard it to complete the burn Congratulations you have successfully burned an Audio CD Copying a CD To make an exact copy of a CD follow the directions below We will leave all the options with their default settings For detailed information please refer to the Nero Burning ROM Reference Chapter in the manual Follow the instructions carefully ME Start Nero Burning Rom Click on the CD Copy icon in the new compilation dialog window If you get the Nero Wizard click on Close Wizard you have already opened Nero you can reach this dialog window through the icon for New Compilation t xj nay ti T 1 On ial Canon Iren verbi CD m F DT RIA MATIA rund Ras Sol mw ssd opet 125 Fecha muc rper 125 inire 48x16x48 CD ReWritable Drive User s Guide Make sure to uncheck On The Fly if you have an older computer system Copying On The Fly is CPU intensive and can cause the burn to fail Use On The Fly only if you have a fast computer system and you do not have available space on your hard drive to cache temporary files F BD D Click on the Burn
18. ck on Close Wizard you have already opened Nero you can reach this dialog window through the icon for New Compilation A Bu paria Tet m CD LT ED Tari o Langue Engh Cone AN Coda Das Comer Dakua mucha orithe by OO ers ua CP Bee posa Det puis 22 48x16x48 CD ReWritable Drive User s Guide Now click on the New button at the right ars Lzrngdabuam ink ok Label Dates Mule Hirmer A new blank compilation window will open Drag amp drop the song you wish to copy from the File Browser window onto the Audio window Use the indicator on the bottom to determine how much data you will be burning and how much free space will be left on your blank media m u gear rdc loreal ele E as Mr us Fass Corer Hi Manes iron coo hor inm ole i rem Lin 21818 Note The latest version of Nero supports files This means you can automatically drag and drop your mp3 songs onto the Audio window without having to convert to wav format first Copying downloading and transferring music or any other files without permission from the artist or copyright holder is forb
19. d Sony and launched in October 1982 CD DA was the first incarnation of the compact disc used to digitally record and play back music at unprecedented 15 48x16x48 CD ReWritable Drive User s Guide quality The standard under which CD DA discs are recorded is known as the Red Book see Glossary for information e CD Extra o A MultiSession CD containing audio tracks in the first session and one CD ROM XA data track in the second session Additional characteristics are defined in the Blue Book standard see Glossary for information e Mixed Mode o ACD including both computer data and CD DA tracks in a single session The data is all contained in track 1 and the audio in one or more following tracks Nero Burning ROM installation Follow the installation instructions carefully and step by step If you encounter a problem refer to the troubleshooting section on this manual ELT iD i Poser Er l Power on your computer 2 Boot into Windows 3 Insert the Nero Burning ROM installation CD into your CD ROM drive 4 The CD will automatically run and the installation program will guide you through the entire installation process 5 Nero will ask for a serial number serial is located on the sleeve 6 Reboot your computer at the end of the installation Note If the installation program does not launch automatically follow these steps l Click on the Start button on the task bar and select Run 2 From the comma
20. d an additional Secondary IDE controller for an additional set of master and slave drives for a total of 4 devices Determine where your new CD RW drive will go and connect to the appropriate cables Primary IDE This IDE controller supports two devices one for the hard disk Master and the other for a second device such as a hard disk or a CD ROM drive The hard disk should be set as the Primary Master The PC needs to use the hard disk to boot up the system unless you are using a SCSI hard drive If you have an empty slot this cable can connect your CD RW drive as the Primary Slave device Make sure the mode select jumper is set to the Slave position Refer to the last section Secondary IDE If the PC is equipped with a second IDE controller or card on the motherboard you can connect your new CD RW drive to this IDE cable You should set your CD RW drive to the Master MA setting and your second device to Slave SL Note Your motherboard layout may be different then the pictures above Please refer to your motherboard manual for your correct IDE1 and IDE2 slots 2 19 48x16x48 CD ReWritable Drive User s Guide Installing The Drive Turn off the PC Make sure there is no power going to your computer prior to beginning the hardware installation This is to help prevent harm to yourself as well as the risk of damage to your computer Remove the computer s cover Please refer to your c
21. for the CD recorder s buffer to be emptied and writing was halted If this occurs during an actual write operation rather than a test your CD may be damaged To avoid buffer underruns make sure that no screen savers or other Terminate and Stay Resident TSR utilities are active they can momentarily interrupt operations and that your working hard disk cannot be accessed via a network Also the CD recorder s position in the IDE bus or the cable length between the computer and CD recorder may cause data slow downs Try connecting the CD recorder as the master on the IDE bus and if possible use a shorter IDE cable between the CD recorder and the host adapter The current CD already contains a closed audio session If you continue you may have problems reading the last audio session on some CD audio players Continue anyway Under the Red Book standard for audio CDs all audio tracks must be written in a single session If you add audio tracks in more than one session playback results will be unpredictable Most CD ROM drives will play back all audio tracks on a CD even if they are recorded in several sessions Most home and car CD players can only play the tracks in the first session 437 c 48x16x48 CD ReWritable Drive User s Guide The current CD already contains tracks and or sessions that are incompatible with the requested operation This error appears if you are trying to add data in a different format to a CD
22. idden Don t steal music 48x16x48 CD ReWritable Drive User s Guide Now open the Write dialog The easiest way to do this is to click on the Write CD icon in the toolbar You will then go to the Write CD dialog box which will undoubtedly look familiar to you it is the same box which you saw for the creation of a new compilation only now the Burn property button is shown on the top CU 1 wo Acn p Dp o wur e ag Cancel mM Wear wis ED kaja nating abe s pes Pia hea Hundes 0l F BURR Prod Haiii You will see several boxes of which some have already been selected All of the preferences may now be examined and changed if necessary From here you can select your burn speed and other settings If you are satisfied with your settings click on the Write button to begin burning your CD ee Hursbes 0d Lapis Note Your Audio CD will not be able to play on a home or car CD player unless the Finalize CD option is checked Check this option after you have finished adding all your songs to finalize the CD and enable it to be playable on a home CD player 48x16x48 CD ReWritable Drive User s Guide Au Nero should now begin caching files and burning your CD When successful will see the message burn process completed successfully at 48x 7200 5 Nero Burning Rom 3 1 X Burn pro
23. ing CDs right from your desktop Nero Burning ROM allows you to copy files from your computer to a recordable compact disc Nero Burning ROM uses special write once media that provides permanent data storage in a format that is readable on virtually all CD Recordable CD R and CD ROM drives In addition the audio CDs you create with your CD recorder can be played in your home or car CD player CD RW media allows you to record and erase data on the CD just like a floppy disk With Nero Burning ROM you can Burn disc images Archive data Back up a hard drive Make CD boot discs Create DOS MAC hybrid discs great for cross platform software developers Create UDF or UDF ISO file system discs e Mixed mode CDs and many other features Nero Burning ROM supports the following formats e CD ROM o Compact Disc Read Only Memory A standard for CDs used as a digital memory medium for personal computers The specifications for CD ROM were first defined in the Yellow Book see Glossary for information e CD ROM XA o XA stands for Extended Architecture CD ROM XA is an extension of the Yellow Book standard see Glossary for information generally consistent with the ISO 9660 logical format but designed to add better audio and video capabilities so that CD ROM can more easily be used for multimedia applications CD ROM XA is also the physical format for Photo CD discs e CD DA o Compact Disc Digital Audio Jointly developed by Philips an
24. isc 30 48x16x48 CD ReWritable Drive User s Guide Using Nero InCD To add or remove files from your CD RW media just drag and drop them onto your CD RW drive as your would any normal file Nero InCD functions like a floppy disk drive To remove files just drag it to your trash bin or right click on the file and select the delete option My Comput CU See Local Disk JE View Favorites ol Help File Edit View Favorites Tools Help Th wet Search Folders Back gt Search Folders Address 72 My Computer ian Address Gu Ivi an 1 wea SSS 3 NEW Documents and Settings mcp cpgw Fi zu u DROP Network Drives e database on magic_cl 1 DRAG Ci Program Files y Tech Support S SUTOEXEC BAT CONFIG SYS Properties Eject E Format F Version Information Note To read a Nero InCD formatted disk on a separate computer you must e Have a multi read CD CD RW drive on the second computer e Install Nero InCD on the second computer e Or install a UDF reader available at http www nero com en download htm soi 48x16x48 CD ReWritable Drive User s Guide Using Nero InCD With Windows XP Windows XP does not allow you to install earlier versions of Nero InCD normally To fix this follow the directions below Download the Nero InCD update file available a
25. le Drive User s Guide If the Primary and Secondary IDE controllers are present but they have yellow exclamation marks read this The protected mode driver for the hard disk controller was not properly initialized when you started Windows previously When this occurs a NOIDE entry is placed in the registry preventing Windows from making future attempts to initialize the protected mode driver You might try to resolve the problem by editing your Registry WARNI NG Using Registry Editor incorrectly can cause serious problems that may require you to reinstall Windows We cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved Use Registry Editor at your own risk NOTE You should make a backup copy of the registry files System dat and User dat before you edit the registry Go to the Start button then Run and type REGEDIT Then go to the following directories to remove the NOIDE entry if it is listed Once removed reboot system HKEY LOCAL NE SYSTEM CURRENTCONTROLSET SERVI VXD 105 After you update the registry restart Windows Windows will then attempt to initialize the protected mode driver for the controller If no problems are encountered the file system and virtual memory will operate in 32 bit mode and Device Manager will not display an exclamation point in a yellow circle for the IDE channels If the protected mode driver is not initialized properly an e
26. me nennen naa annee 14 Nero Burhing ROM as 15 NERO BURNING ROM 5 enne aae nnn 16 SOFTWARE DESCRIPTION MU een ERN dS E 17 BEFORE Er cS M p LEE LC OM E 17 NERO BURNING ROM enn n e aaa aee nnn 18 CREAT ESO 19 CREATE ANADO a tA 22 25 SAVING AUDIO TRACKS blan e BAR oa ac ER Ec PAP a 27 Nero aa RR EMEN EE 28 NERO ING en deseas 28 FORMATO DR W DISC ee 29 US INC NERO ING D ar 31 USING NERO INCD WITH WINDOWS eme e eme aan eee nnne nn 32 Troubleshooting 2 2 33 SUGGESTIONS FOR RESOLVING COMMON e emisse enn 33 ERROR MESSAGE DESCRIPTIONS na Henne el 37 OTHER PROGRAM MESSAGES wise obe a Db Da ale IM Vs oh Dao da EE cU Pid paw dcn 39 USING THE ONLINE FEC ee 40 Limited Warranty nee en 41 48x16x48 CD ReWritable Drive User s Guide Introduction Congratulations on your purchase of the CD
27. n see only data recorded in the first session on the CD but not in subsequent sessions it may be that e You recorded the CD in CD ROM Mode 1 format while your multi Session CD ROM drive only recognizes CD ROM XA Mode 2 multi Session CDs See the chapter on How to Make a Multi Session CD e Your CD ROM drive does not support multi Session at all If you can see only data recorded in the last session you may have forgotten to link your new data with data previously recorded on the CD Make sure to import the session before writing to the CD See the online help for more details CD ROM Drive I ncompatibility with Recordable CDs Sometimes it appears that you wrote a CD without trouble and can read it on your CD recorder However when you put it in a standard CD ROM drive the CD is ejected or you get error messages such as No CD ROM or Not ready reading or you have random problems accessing some files or directories You may find that the problems vanish completely when reading the CD on a different CD ROM drive This maybe due to compatibility problems with some CD ROM drives especially older ones Some CD ROM drives lasers are not calibrated to read recordable CDs whose surface is different from that of factory pressed CDs If m o9 5 48x16x48 CD ReWritable Drive User s Guide your CD ROM drive reads mass produced silver CDs but not recordable CDs check with the CD ROM drive manufacturer to determine
28. nd prompt type D Setup exe Where D is your CD ROM drive 3 The installation program will guide you through the entire installation 48x16x48 CD ReWritable Drive User s Guide Software Description za MESIMI snilmare gmbh iri dla german hang Cod i d al righty mzrzryrd Were 5 8 2 4 d Hume THEE Fima uH Nero is a professional package that gives you many features not found in other software packages In the following paragraphs you ll be introduce to the Nero Burning ROM interface as well as step by step instructions on how to record CD R CD RW media The software has extensive on line help on all of its features and other general information If you are looking for information click on Help within the Nero Burning ROM program and you will find a wide variety of topics including how to guides Before You Begin Auto Insert Notification must be turned off before you begin Failure to do so may result in problematic behavior such as system hangs and loss of data Turn off Auto Insert Notification for every CD drive on your IDE bus including the CD recorder itself To turn off the Auto I nsert Notification follow these steps 1 Right click on the My Computer icon on the desktop 2 Select Properties from the menu The system properties dialog box opens 3 Click on the Device Manager tab 4 Click
29. oading Method Average Access Time 120 msec avg Writing mode Disc at Once Session at Once Track at Once Multi Session Packet Writing CD DA CD ROM CD ROM XA CD Extra CD I Writing format Mixed Mode CD Video CD Photo CD CD TEXT Bootable CD Power requirements DC 5V 12V Installation Horizontal Vertical Temperature Operating 59C 409C Non Operating 30 C 65 C Humidit Operating 596 9096 Non Operating 596 9596 RH Package Contents The CD ReWritable package contains the following items CD RW Drive One Piece CD Media CD Mastering Software User s Manual Quick Install Guide Audio and Data Cables Warranty Card System Requirements IBM Compatible PC Pentium 166 MHz or higher Windows XP 2000 ME 98SE 95 NT4 One Available Enhanced IDE port 64MB RAM 128MB recommended 32MB Free Disk Space 48x16x48 CD ReWritable Drive User s Guide Hardware Installation Handling Static Sensitive Devices The CD ReWritable drive like all electronic equipment is static sensitive Please take the proper precautions when handling the drive Avoid touching the IDE connector pins as well as the audio connector pins and the jumper pins Keep the drive in its conductive wrapping until you are ready to install the drive in your computer Host I nterface Connections It is recommended that you use separate IDE ports for your hard drive and your drive The drive should be connected to a seconda
30. omputer s User s Guide on how to remove the computer s cover c8 Locate an available 5 drive bay Locate an empty 574 drive bay within your computer It may be necessary to remove a square iron plate Please refer to your computer s User s Guide for assistance u Slide the CD ReWritable drive into the empty bay 48x16x48 CD ReWritable Drive User s Guide Connect the power supply cable into the DC input connector on the back of your drive Connect the 40 pin IDE cable into the CD ReWritable drive s E IDE connector Make sure to align the redlined edge of cable with Pin 1 of the IDE connector LU Connect the analog cable from your sound card to the Audio out connector on your CD RW drive If necessary ZZ Eni u x feeder FI ES Fre r Eg ont wu a T If you have a sound card or an audio interface card use the audio cable to connect from the sound card audio port to the CD ReWritable drive s analog audio out connector located on the back panel 2 ie E 48x16x48 CD ReWritable Drive User s Guide cu Secure the CD ReWritable drive against the chassis of your computer Secure the drive using four screws included in the accessory pack Reattach the computer s cover baw Ta T 159 FER mower Reconnect all power cords to the computer 2 18 48x16x4
31. rence to radio communications However television reception interference can be determined by turning the equipment off and on The user is encouraged to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment For Europe C The drive is conformity withthe directive and low voltage directive 48x16x48 CD ReWritable Drive User s Guide Table Of Contents IntroductiOlus ae 6 SPECIFICATIONS a 7 Package Contents an en 7 System Requirements 7 Hardware Installation as 8 FUMPER SETTINGS aa er ee eine en 9 CONNECTING LDE CABLE Sy een 10 INSTALEING TAE DRIVE 11 14 WiNDOWS XP 2000 ME 98SE 95 5 nnns 14 DOS WINDOWS 3 BEINST ALLATLONGA a een 14 WINDOWS NT 4 0 HH HI he
32. repair or replace at no charge the product that in its opinion is defective The original purchaser is responsible for packing the product for shipment and for the charges to ship the failed product If the failed product has been modified in any way without the consent of OMagic or if the failure is the result of misuse abuse or misapplication OMagic has no obligation to repair or replace the failed product Except as expressly provided above the hardware and accompanying written materials including the Users Guide are provided as is without warranty of any kind including the implied warranties of merchantability and fitness for a particular purpose This specifically does not warrant the operation of the hardware and will not be liable for any direct indirect consequential or incidental damages arising out of the use or inability to use such product even if has been advised of the possibility of such damages Some states do not allow the exclusion or incidental damage so the above limitation may not apply 41 R CDRW4848 02 Ver 1
33. rporation IBM is a registered trademark of International Business Machines Corporation All other trademarks and product names used within this manual are the property of their respective companies and are hereby acknowledged Copyright 2002 I OMAGIC Corp all rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form by any means without prior written consent of I OMAGIC Warranty I OMAGIC Corporation warrants the products it sells will be free from defects in materials workmanship Consult the warranty card for complete warranty information 48x16x48 CD ReWritable Drive User s Guide FCC Compliance Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can emit radio frequency energy and if not installed or used in accordance with the instructions may cause interfe
34. rror message will be displayed and the NOIDE registry entry will be re created Windows will use the MS DOS compatibility mode file system the next time you start the computer If the CD ROM drive is connected to a sound card or controller card read this Make sure the sound card or controller card are installed properly working properly and compatible with Windows 98 95 We do not recommend the use of a sound card with our CD ReWritable drive 234 48x16x48 CD ReWritable Drive User s Guide Problems Reading Recordable CDs If you have successfully written a CD but have problems reading it there are a number of possible reasons e fthe CD can be read on the CD recorder but not on a standard CD ROM drive check in Disc I nfo and Tools to make sure that the session containing the data you just wrote is closed CD ROM drives cannot read data from a session which is not closed e f your CD is ejected or you receive an error message or you have random problems accessing files from the CD the problem may be that your CD ROM drive is not well calibrated to read recordable CDs or does not support CD R CD RW media e f you recorded the CD using the DOS filenames option in the File Names tab but there are nonetheless difficulties in reading back the CD on DOS or Windows 3 1 system it may be that you have an older version of MSCDEX before version 2 23 on your system Problems Reading Multi Session CDs If you ca
35. ry IDE controller port as Master This will ensure your hard drive s performance and speed are not affected by having the drive on the same cable Additionally if you have a CD ROM drive or a CD R drive you should attach it to the primary IDE controller port as a Slave drive Connect the internal IDE flat cable to the IDE interface port of your host Connect the other end to one of the IDE connectors at the rear of the CD ReWritable drive Before You Begin The following diagram shows you the rear view of your CD ReWritable drive Familiarize yourself with the drive before installing the unit into your computer Locate where the drive will be connected first and then make sure you have all the necessary parts for the connection AUDIO OUT IDE CONNECTOR bu ONLY DIGITAL m ANALOGS h 2 u Eau gt DG RGGL SLA DC INPUT Out Device Jumpers IDE Connector Power Connector Note Item displayed may vary 48x16x48 CD ReWritable Drive User s Guide Jumper Settings On the rear panel of the CD ReWritable drive you will find three pairs of jumpers CS CSEL SL Slave and MA Master Use the jumper cap to set the device to CS SL or MA mode corresponding to your PC configuration see fgure below The default setting is Slave mode Improper or conflicting setting will cause the unit to no
36. t http www nero com en download htm Right click on update file after it has been saved to your hard drive Select Properties and select the Compatibility tab Click on Run this program in compatibility mode for and select Windows 2000 InCD 232Up exe Properties ax p m Se General Yerson IF you have problems wath the program and it worked correctly an eames version of Windows select the compalibifty mode thal matches that salier version Lompahbilly mode is Run the program in compatbiity mode for Windows 20m vw Display seltrig C Run in 256 colos C Run in k 48D screen rezotutibm al visual Herne Leam more about proia _ You should now be able to install Nero InCD using the update file it which will run under Windows XP Note This is only a temporary fix until Ahead releases a fully compatible version of InCD for XP This temporary fix may not work properly on all systems Installing InCD in this fashion is up to your discretion Be sure to check the Nero website http www nero com for program updates 232 48x16x48 CD ReWritable Drive User s Guide Troubleshooting To help you identify and resolve some problems you may encounter with Nero Burning ROM this chapter provides the following information e Suggestions for Resolving Common Problems e Error Message Descriptions e Other Program Messages
37. t be detected by your computer Dc INPUT 2 12 ho eoe Finster dd miia Note Before installing the drive into your system make sure the jumper setting is set correctly Master Mode the writer is the only device connected to the I DE cable gray ribbon it should be set to Master MA Slave Mode If the writer will be sharing the IDE cable with another device one device should be set to MA and the other set to Slave SL MA is recommended for writer on secondary IDE To set the drive as the Slave SL drive move the jumper to the SL position Cable Select As the name implies with this setting the position of the connector on the IDE cable determines which device is master and which is slave The goal of cable select is to eliminate having to set Master and Slave jumpers To use Cable Select CS move the jumper to the CS position Cable Select CS mode is not needed on most normal systems unless the drive you are replacing is set to CS already If you are unsure please contact your computer manufacturer Note The middle connection on the IDE cable is the Slave position The end connection on the IDE cable is the Master position sus 48x16x48 CD ReWritable Drive User s Guide Connecting IDE Cables Your computer should have 2 IDE controllers on your motherboard Each IDE controller supports 2 devices You should have one Primary IDE controller with a master and a slave an
Download Pdf Manuals
Related Search