ADC-9033 User Manual
Contents
1. SERIAL NUMBER LABEL FLAT METAL PLATE MOUNTING HOLES Figure 3 Flat Metal Plate Installation Option 3 Install the chassis in the desired location using the Mounting Holes on the Flat Metal Plate Mounting screws are not provided bv Ross Video Angle Mounting Bracket The Angle Mounting Bracket Figure 4 allows a single GearLite module to be installed in positions not possible with the flat metal plate The bracket has a 90 angle Mounting screws are not provided bv Ross Video Installation Iss 04 10 0 Figure 4 Angle Mounting Bracket 11 Installation 155 04 Setup Power Adapter and Supplv Connect the PS 9000 power adaptor to the power supplv connector The PS 9000 provides up to 2A of regulated 5V DC 5 The DC power cord has a locking connector that securelv fastens into the power supplv DC jack on the ADC 9033 The ADC 9033 has a standard miniature power jack center pin positive If using an adaptor other than the PS 9000 ensure that e the polarity is correct the voltage is 5V DC regulated to 5 sufficient current for the ADC 9033 is supplied Caution Use of improper adaptors may damage the ADC 9033 N and will void the warranty Installations outside of North America using line voltages of 200 240V require a plug certified for the country of use to be installed on the supplied line cord Refer to the section Important Regulatory and Safety Notices to Service2. Default Set This menu item enables a reset to be done on some or all of the user controlled settings Holding the Down button for three seconds will reset the six proc amp level settings Video Black Level Offset Setup On Chroma Hue and U Gain to unity and change setup menu value to On or Off as is normal for the selected standard format and level Holding the Up button for three seconds will reset all user controlled settings including the proc amp settings to their default states Note that when selecting this option the state of the DOWN and UP LEDs will indicate if any settings are not in their default states Ifthe DOWN LED is flashing it indicates there is at least one proc amp setting that is not in its default state Defaulting the proc amp will be indicated when the DOWN LED is lit solid Ifthe UP LED in this setting is flashing it indicates that at least one user controlled setting proc amp setting or otherwise is not in its default state Defaulting all user controlled settings will be indicated when the UP LED is lit solid Force Mono Use this menu to remove the chroma from the output SDI Setting this option to On results in a monochrome SDI output and also disables the ERROR LED which reports missing color Sync in the input VI Blanking Use this menu to select whether data or test signals in the vertical blanking get passed or stripped from the SDI output VI End Use this menu to set whe
3. ADC 9033 Analog Composite Component YC to SDI Video Converter User Manual IROSS Video Production Technology ADC 9033 User Manual Ross Part Number 9033DR 004 04 e Release Date October 11 2012 The information contained in this manual is subject to change without notice or obligation Copyright O 2012 Ross Video Limited All rights reserved This work is proprietary and confidential to Ross Video Limited its subsidiaries and its other affiliated corporations and may not be copied distributed sold or otherwise used or relied upon without the express written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited Patents This product is protected by the following US Patents 4 205 346 5 115 314 5 280 346 5 561 404 7 034 886 7 508 455 7 602 446 7 834 886 7 914 332 This product is protected by the following Canadian Patents 2039277 1237518 1127289 Other patents pending Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademarks ROSS is a registered trademark of Ross Video Limited Geartite is a trademark of Ross Video Limited Ross ROSS ROSSB and MLE are registered trademarks of Ross
4. Technical support e Upcoming trade show information Telephone Technical After Hours Emergencv Support i Email Telephone General Fax Information Email Website Visit Us Visit our website for Company information and news 1 613 652 4886 1 613 349 0006 techsupport rossvideo com 1613 652 4886 1 613 652 4425 solutions rossvideo com http www rossvideo com e Related products and full product lines Online catalog Testimonials ROSS Video Production Technology
5. e Composite or Component analog video signal inputs supported NTSC PAL B PAL M PAL N gt YPRPB input from Betacam and SMPTE EBU formats RGB input from SMPTE EBU and NTSC related formats 1 line processing delay refer to specifications 10bit A to D quantization and signal path 3 line adaptive comb filter 2X over sampling for excellent frequency response 4 SDI outputs Extensive proc amp controls Programmable vertical interval blanking User selectable Setup for NTSC and PAL M standards Black Level Offset Low jitter Input and conversion status indicator LEDs Small brick form factor 5V universal adapter with locking DC connector e 3 year warranty 7 Introduction Iss 04 Installation Static Discharge Whenever handling the ADC 9033 and other related equipment please observe all static discharge precautions as described in the following note to sensitive semiconductor devices Avoid handling circuit boards in high static environments such as carpeted areas and when wearing synthetic fiber clothing Always exercise proper grounding precautions when working on circuit boards and related equipment ESD Susceptibility Static discharge can cause serious damage Unpacking Unpack each ADC 9033 module you received from the shipping container and check the contents to ensure that all items are included If any items are missing or damaged contac
6. 3129 1102 a Three BNCs are available depending on signal type Specifications Iss 04 26 Service Information Warrantv and Repair Policv The GearLite ADC 9033 is warranted to be free of anv defect with respect to performance qualitv reliabilitv and workmanship for a period of THREE 3 years from the date of delivery to the customer In the event that your GearLite ADC 9033 proves to be defective in any way during this warranty period Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this GearLite ADC 9033 has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the THREE 3 year warranty period In no event shall Ross Video Limited be liable for direct indirect special incidental or consequential damages including loss of profits incurred by the use of this product Implied warranties are expressly limited to duration of this warranty This ADC 9033 User Manual provides all pertinent information for the safe installation and operation of your GearLite Product Ross Video policy dictates that all repairs to the GearLite ADC 9033 are to be conducted only by an authorized Ross Video Limited f
7. pinching particularly at plugs convenience receptacles and point where they exit from the apparatus Warning Indoor Use WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Do not block ventilation openings Install in accordance with manufacturer s instructions Do not install near heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not use this apparatus near water Only use attachments accessories specified by the manufacturer Unplug this apparatus during lightning storms or when unused for long periods of time Clean only with a dry cloth To avoid electrical shock disconnect the A C power cord before any servicing Refer all servicing to qualified personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug damage liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped EMC Notices United States of America FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device pursuant to part 15 of the Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses an
8. Personnel at the front of this manual for details Cable Connections Overview Connect the cables to the ADC 9033 according to the designations indicated on the chassis label and Figure 5 The input is internally terminated at 75ohm It is not necessary to terminate unused outputs CVBS Y Y G IN U B IN SDI OUT 2 SDI OUT 4 60606004 CNIR IN SDI OUT 1 SDI OUT 3 Figure 5 ADC 9033 Connections Setup Iss 04 12 Status and Selection LEDs The front edge of the ADC 9033 has four LED indicators that displav the status of the input signals and indicate menu function and selections Figure 6 ERROR LED DOWN LED UP LED OK LED Figure 6 ADC 9033 Front Edge Status Indicator LEDs Table 1 describes the status LEDs available on the ADC 9033 Table 1 Status LED Descriptions Flashing Red Function When lit this LED indicates that a valid input signal is present and no anomalies have been detected The ADC 9033 is functioning correctiv When flashing this LED indicates when the color svnc is not locked either due to an absence of a color signal or an incorrect video standard setting Applies to composite and V C formats Flashing Vellow When this lit this LED indicates that an invalid signal has been detected or no input is present on the input The SDI output is muted When lit this LED indicates the menu item range is greater than the lower limit but equal to or
9. SMPTE EBU with 525 line signals anv can have setup Input Impedance 75ohm terminating Return Loss gt 41dB to 5MHz Bandwidth 3dB Q 6 5MHz Line Rate Tilt lt 0 5 Field Rate Tilt lt 0 5 CMRR Better than 50dB 50 60Hz Differential Phase lt 1 Differential Gain Number of Outputs 4 Standard 259M 270Mbps 525 625 lines Impedance 75ohm Return Loss gt 19dB to 300MHz Signal Level 800mV 10 DC Offset lt 50 Rise and Fall Time 750 20 80 Overshoot 25 Specifications Iss 04 lt 9 Table 5 ADC 9033 Technical Specifications Categorv Parameter Specification SDI Video Outputs Short Circuit Output Protected Luminance Frequency 0 13dB to 5 5MHz Response Group Delay lt 5ns to 5 5MHz RMS SNR Luma Channel gt 53dB to 5MHz unweighted RMS SNR Chroma Performance Channel gt 53dB to 5MHz unweighted Thermal Stability lt 0 1 C Quantization 10 bits Processing Delay Analog 1 line 6 02hs NTSC Input to SDI Output 1 line 7 63hs PAL Require Voltage 5V DC 5 regulation Current Consumption lt 650mA typical Total Power 3 3W typical 20 C to 40 C 68 F to 104 F Thermal Environment ambient non condensing 13cm x 9cm x 2 5cm Dimensions approx 8 x 3 5 x 1 Weight approx
10. RPB analog component inputs the ADC 9033 is the ideal analog to SDI converter for virtually all video conversion requirements All analog RGB YPRPB and YC video formats are supported with the converter powering up in the previously selected standard format and level All units ship set to 525 YPRPB component for SMTE levels The ADC 9033 provides high quality conversion into four separate 270Mbps SDI coaxial outputs The use of a 10bit A to D converter and circuitry along with a high quality 3 line adaptive comb filter ensures clean conversion of composite signals Proc amp controls on the front edge enable adjustments to the signal in the digital domain The chassis front edge also provides power error and function LEDs for visual reference universal power adaptor and line cord suitable for the country of use 15 supplied with each module Various mounting options are included that enable a wide range of installation choices The GearLite ADC 9033 is a high quality universal analog to SDI video converter making it an ideal solution for existing analog facilities in a growing SDI world Simplified Block Diagram ANALOG IN CVBS Y YIG sol our 1 EDH 3 LINE INPUT ADAPTIVE INSERTION AMPLIFER amp DECODER SERIALIZER SDI OUT 3 SDI OUT 2 SDI OUT 4 Figure 1 Simplified Block Diagram of ADC 9033 Functions Introduction Iss 04 6 Features The ADC 9033 includes the following features
11. Video Limited e VELCROB isa registered trademark of Velcro Industries B V Allother product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remain exclusive property of their respective owners Important Regulatorv and Safetv Notices to Service Personnel Before using this product and anv associated equipment refer to the Important Safety Instructions listed below to avoid personnel injury and to prevent product damage Product may require specific equipment and or installation procedures to be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these specific requirements Symbol Meanings Protective Earth This symbol identifies a Protective Earth PE D terminal which is provided for connection of the supply system s protective earth green or green yellow conductor This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment Warning The symbol with the word Warning within the equipment manual indicates potentially hazardous situation which if not avoided could result in death or serious injury Caution The symbol with the word Caut
12. actory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ross Video Limited factory representative will automatically void the warranty Please contact Ross Video Technical Support for more information In Case of Problems Should any problem arise with your GearLite ADC 9033 please contact the Ross Video Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your GearLite ADC 9033 If required a temporary replacement module will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ross Video Limited will be shipped collect The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited beyond the warranty period without charge for the life of the equipment 27 Service Information Iss 04 Notes Service Information Iss 04 28 Notes 29 Service Information Iss 04 Notes Service Information Iss 04 30 A Contact Us Contact our friendly and professional support representatives for the following Name and address of your local dealer Product information and pricing
13. d can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense approved by Ross Video Limited could void the user s authority to Notice Changes or modifications to this equipment not expressly operate this equipment CANADA This Class digital apparatus complies with Canadian ICES 003 appariel numerique de la classe est conforme la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and found to comply with the limits for Class Digital device Notice This is Class product In domestic environments this product may cause radio interference in which case the user may have to take adequate measures Maintenance User Serviceable Parts Routine maintenance to this GearLite product is not required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Support using the numbers listed under the Contact Us section o
14. dhesive on the bottom of the two VELCROQ brand Surface Mount Strips 2 Adhere the Surface Mount Strips to the bottom side of the chassis Figure 2 SURFACE MOUNT STRIPS TD SERIAL NUMBER LABEL PROTECTIVE BACKING FILM Figure 2 Surface Mount Installation Option 3 Remove the Protective Backing Film from the other side of the VELCRO brand Surface Mount Strips 4 Press the chassis into position on the surface you want to mount it to Operating Tip An additional VELCRO brand Surface Mount Strip is available to mount the power adapter Non Slip Pads Four non slip adhesive pads have been supplied for desktop placements Simply remove the protective backing film from the adhesive and affix one non slip pad to each of the four corners on the bottom of the chassis Optional Mounting Accessories Ross Video is committed to providing practical solutions for the needs of your high quality broadcast facility 9 Installation Iss 04 Flat Metal Plate Use the flat metal plate for permanent mounting to a rack a desk or anv other location where bolts or screws can be applied Be sure to position the module to allow for operator adjustments if required To install the Flat Metal Plate 1 Remove the 2 screws from the bottom of the chassis 2 Install the Flat Metal Plate onto the bottom of the chassis Figure 3 using the screws provided in the Mounting Kit Do not use the screws removed during Step 1
15. el Unity Level between Min and Unity Min Level Max Level Offset between Unity and Max Black Level Offset Unity Offset between Min and Unity Min Level Max Chroma Level Level between Unity and Max Unity Level between Min and Unity Min Chroma Level 17 7 Configuration Iss 04 Table 2 Function Setup and Configuration Menu Function LED Displav Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position gt 180 Hue between 0 and 180 0 between 180 and 0 lt 180 Gain between Unity and Max Unity Gain between Min and Unity Min Gain Setup On Reset all User settings to Factory Default State Unity Default Set See Notes Reset only Proc Amp settings to Factory Default State Unity Force Mono VI Blanking Configuration Iss 04 18 Table 2 Function Setup and Configuration Menu Function LED Displav Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position VI Ends 1 line before default VI Ends at default Line 20 for 525 Line 23 for 625 VI Ends 1 line after default VI Ends 2 lines after default See Notes F PLL Enable a Refer to Table 4 on page 24 for a list of supported video standards Function Menu N
16. iguration Use the Function Select switch and the Down and Up buttons to configure the ADC 9033 to convert analog video signals to SDI Settings are described in the section Function Setup and Configuration Menus on page 16 Refer to Figure 7 for switch and button locations Function Down Button Select Up Button b i e e ee Figure 7 ADC 9033 Switch and Button Locations General Operating Rules Please note the following important operating rules for the ADC 9033 For each of the supported Video Standards NTSC PAL B PAL M PAL N the card stores the default video settings independently in non volatile memory The module always powers up in the last configuration used Always check to see that the input OK LED is lit If not check that the inputs are valid and the correct Video Standard has been selected from the Function menu Function Selection Start by setting the Function Select switch to Position 0 and adjust your video input to the correct Video Standard NTSC 525 60 PAL B 625 50 PAL M 525 50 PAL N 625 60 NTSC 525 60 is the default standard Refer to for complete settings information Example Configuration 1 To configure the Video Standard function Tum the Function Select switch to Position 0 The default configuration is NTSC 525 60 The DOWN LED will be unlit and the UP LED will be flashing to indicate NTSC 525 60 configuration selection 2 T
17. ion within the equipment manual indicates potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Warning Hazardous Voltages This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons ESD Susceptibility This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event bb b b B Important Safetv Instructions 1 10 11 12 13 14 15 Warning Read these instructions Keep these instructions Heed all warnings Follow all instructions The safe operation of this product requires that a protective earth connection be provided A grounding conductor in the equipment s supply cord provides this protective earth To reduce the risk of electrical shock to the operator and service personnel this ground conductor must be connected to an earthed ground Do not defeat the safety purpose of the grounding type plug grounding type plug has two blades and a third grounding prong The third prong is provided for your safety If the provided plug does not fit in to your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or
18. le for the current video format or level will cause an automatic change in the video format and or level to an available type b Formats available for selection are determined by the current setting of video standard c Levels available for selection are determined by the current setting of video standard and for mat 23 Configuration 155 04 Supported Video Standards Table 4 presents the supported video standards formats and their levels based on selections made in the Function Menu Table 4 Supported Video Standards Function Menu Item NTSC 525 PAL B 625 SMPTE EBU Betacam RGB only Green SMPTE EBU NTSC Related RGB svnc on all SMPTE EBU NTSC Related YIC VPRPB SMPTE EBU Betacam MII Composite RGB sync only on Green SMPTE EBU RGB sync on all SMPTE EBU YIC Composite YIC Composite YIC Configuration Iss 04 24 Specifications Specifications are subject to change without notification Table 5 ADC 9033 Technical Specifications Categorv SDI Video Output Parameter Number of Input Signals Specification 1 Signal Standards Accommodated Signal Formats Accommodated NTSC PAL B PAL M PAL N combinationN RGB as SMPTE EBU or NTSC related with 525 line signals anv can have setup as Betacam or
19. less than unitv Yellow When flashing this LED indicates that the selected menu item is adjusted to the lower limit Off Yellow When unlit this LED indicates the selected menu item is adjusted above unity When lit this LED indicates that the menu item range 15 less than the upper limit but equal to or greater than unity Flashing Yellow When flashing this LED indicates that the selected menu item is adjusted to the upper limit Off 13 Setup Iss 04 When unlit this LED indicates that the selected menu item is adjusted below unity a A valid signal is defined as any analog composite video signal standard input into ADC 9033 which matches the setting of the Video Standard that has been selected in Function Setup and Con figuration Menu In other words if the converter is in its default state for NTSC 525 60 video then only an NTSC 525 60 composite video signal input will cause the OK LED to be lit other an alog composite video signal of a different standard PAL B PAL M PAL N that is input into the converter will be invalid and ERROR LED will be lit b For menu items that have multiple selections the LED will be in a state as indicated in the Function Setup and Configuration Menu For menu items that have a range the descriptions are provided in the section Function Setup and Configuration Menus on page 16 Setup Iss 04 14 Conf
20. lt state Standard mode a 3 line adaptive filter is emploved to assure the highest qualitv conversion to SDI video output standards In VTR mode however the 3 line adaptive filter is disabled and a notch filter is used instead Video Level Use this menu to adjust the video level of the SDI signal to match the white level of the incoming video This setting also affects the black video level menu so it will be necessarv to go back and forth between these two adjustments to get both black and white levels set This menu has a 2 button quick default to unity default Press both up and down buttons at the same time and hold for three seconds Since the white and black levels are linked together defaulting the white level will automatically default the black level as well Black Level Offset Use this menu to adjust the level of the SDI signal to match the incoming video black level This setting is also affected bv changes in the Video Level menu see above so it will be necessarv to go back and forth between these two adjustments to get both black and white levels set This menu has a 2 button quick default to unitv default Press both up and down buttons at the same time and hold for three seconds to jump to unitv Chroma Level Use this menu to adjust the video chroma level of the SDI signal to match the incoming video color levels This setting and the U Gain setting are adjusted together for best results using an SDI vector scope Thi
21. n last page of this manual products are covered generous 3 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration You can also contact Ross Video for more information on the environmental performances of our products Introduction Overview The ADC 9033 Analog Composite Component VC to SDI Video Converter is high quality signal conversion solution within the growing family of GearLite compact self contained modular products Supporting NTSC PAL B PAL M PAL N combinational analog composite video standards and RGB and YP
22. o change Video Standard configuration to PAL 625 50 15 Configuration Iss 04 Keep the Function Select in Position 0 Press the Down button once The DOWN LED will be unlit and the UP LED will be lit to indicate PAL 625 50 configuration selection Function Setup and Configuration Menus single press of the Down and Up buttons is momentary click of the button unless indicated by h Table Legend Press the Up button from the default position Press the Down button from the default position Hold Up or Down button for 2 3 seconds for faster adjustment or special function G Factory default state Lit LED display e Unlit LED displav X Flashing LED display Table 2 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN Position NTSC 525 Video PAL B 625 Standard VPRPB Composite RGB svnc on Green RGB OC CO e e CO e Configuration Iss 04 16 Table 2 Function Setup and Configuration Menu Function LED Displav Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position SMPTE EBU VPRPB RGB Betacam Levelsa or NTSC Related Standard Standard Mode VTR Mode VTR Mode On Max Level Level between Unity and olol le 0 Video Lev
23. otes Some of the menu items in Table 2 are explained here in further detail as follows Video Standard Use this menu to select the video standard of the incoming analog video Please note that not all formats and levels exist for all standards For example RGB does not exist for PAL N or PAL M since this format exists in 525 and 625 line versions and those are covered by the other two standards Refer to Table 4 on page 24 for a list of supported video standards Video Format Use this menu to select the video format of the incoming analog video Note that not all formats and levels exist for all standards When PAL M or PAL N are the selected video standard the two component formats YPgPg and RGB are unavailable Refer to Table 4 on page 24 for a list of supported video standards YPgPg RBG Level Use this menu to select the video level of the incoming analog component video Note that levels that do not apply for the currently selected video standard and format will be unavailable when in this menu Refer to Table 4 on page 24 fora list of supported video standards 19 Configuration Iss 04 Standard VTR Mode This menu enables the module to convert either broadcast qualitv or non broadcast qualitv analog input signals independentiv selectable according to the level of the video qualitv to be received The level of conversion qualitv required for a non broadcast VTR signal is different than a broadcast signal In the defau
24. re the end of blanking and the beginning of video is at the top of the picture Setting is relative to the normal end of VI blanking for SDI line 20 for 525 and line 23 for 625 For more info or help on this feature contact Ross Video Technical Support 21 Configuration Iss 04 Status Report This menu selection is primarily for Ross Video use If an on board error has occurred with the ADC 9033 this menu item will provide some indication as to the nature of the problem In Status Report mode the DOWN and UP LEDs will flash at the same time and the number of consecutive flashes will indicate the tvpe of error A simple single flash followed bv a long pause before repeating means is reported If multiple flashes occur record the number of flashes Use the Down button to clear this error and view if any other errors are concurrent Contact Ross Video Technical Support if you require any assistance The Up button provides access to the firmware version display 1 While holding the Up button the DOWN LED will flash the upper digit of the firmware version 2 While the DOWN LED is flashing note the status of the UP LED e Ifthe UP LED is on this indicates that the lower digit is zero Ifthe UP LED is off then after the down LED is finished the up LED will flash for the lower digit of the version This is followed by a pause where both LEDs are off and then repeats 3 Release the Up button to return to the S
25. s menu has a 2 button quick default to unity default Press both up and down buttons at the same time and hold for three seconds Hue Use this menu to adjust the video Hue angle of the SDI signal to match the incoming video color levels This menu is disabled for component formats This menu has a 2 button quick default to unity default Just press both up and down buttons at the same time and hold for three seconds U Gain Use this menu to adjust the gain in the U component of the SDI signal to match that expected for the incoming video color levels This setting and the Chroma setting are adjusted together for best results using an SDI vector scope This menu has a 2 button quick default to unity default Press both up and down buttons at the same time and hold for three seconds Configuration Iss 04 20 If the incoming analog composite video has Setup then this user controlled setting should be set to On If there is no Setup on the incoming analog composite video then this user controlled setting should be set to Off This setting controls how the decoder will scale the analog video and where it will set black in the digital domain The default setting for this control is determined bv the standard in use with NTSC and PAL M defaulting to On with the DOWN LED unlit and the UP LED lit For RGB setup should be changed from the default On to Off PAL B and PAL N have setup set to Off and the menu locked out
26. t your sales representative or Ross Video directly Mounting and Installation The ADC 9033 can be mounted in any convenient location However to ensure long life for this product observe the following precautions and operating requirements Maintain an ambient temperature of 20 C to 40 C Allow for air circulation around the chassis for convectional cooling Many different mounting positions are possible with the included mounting hardware Some installation options are permanent and require careful consideration of the final positioning before installation Please note that in some mounting locations the power adaptor must be affixed in a similar manner as the chassis Other possible options include the use of adhesive magnetic sheets not included affixed to the chassis and the power adaptor for removable mounting on metal cabinets etc Cable ties may be necessary in some applications to relieve strain on the mounting hardware and the connectors Surface Mount Strips The included VELCRO brand surface mount strips allow the GearLite module and power supply to be affixed to a permanent location during use and easily Installation Iss 04 8 removed for adjustments Carefullv consider the installation location before proceeding the adhesive is verv aggressive and is not easilv removed The adhesive will cure fullv in 24 hours To install the Surface Mount Strips 1 Remove the Protective Backing Film from the a
27. tatus Report mode PLL Enable This menu item selects one of two internal clock locking circuits For normal operation the default setting of On should be maintained For input video signals which exhibit asynchronous switches between non timed sources or signals with excessive noise the Off setting provides faster locking but adds more jitter to the output signal Menu Accessibility Note that some user controlled settings may become inaccessible depending upon the Video Standard and Video Format that have been selected from the menu Table 3 illustrates which menu items are unavailable in each of the video standards and formats Table 3 ADC 9033 Menu Access by Video Standard Format Selection Analog Video Formats and Switch Position and Standards Menu Item YPRPg RGB Composite YC 525 625 NTSC PAL 0 Video Standard 1 Video Format 2 VPRPB RGB Levelst Configuration 155 04 22 Table 3 ADC 9033 Menu Access Video Standard Format Selection Analog Video Formats and Switch Position and Standards Menu Item YPRPg RGB 525 625 NTSC Standard Mode Video Level Black Level Offset Chroma Level Hue U Gain Setup On Default Set Force Mono VI Blanking VI End Status Report 3 4 5 6 7 8 9 A B D E F PLL Enable a Selecting a video standard that is not availab
Download Pdf Manuals
Related Search