INSTALLATION MANUAL
Contents
1. Indicator light blinks in blue e Blinks once Problem with wireless connection e Blinks twice Problem with power control unit e Blinks three times Power control unit over heating Indicator light blinks in yellow e Blinks once Probem with sensors e Blinks twice Problem with sensor unit e Blinks three times Faulty installation position of the sensor unit A Sensor unit will automatically recognize its installation position during the first time the cooker is used for cooking After the auto recognition is completed the stove guard will prevent the use of cooker and oven if the sensor unit is removed from its original installation position To enable use of the cooker place the sensor unit back to the mounting bracket If the problem persists the auto recognition might not have been successful Ensure the correct position of the sensor unit see installation step 2 2 and manually reconnect the wireless connection according the installation manual chapter 5 2 The fault should be then reseted automatically in two minutes Go into the Manual adjustment mode and set up the wireless connection manually see chapter 5 Ensure that the batteries are not empty Check the correct position of the batteries marked on the bottom of the battery case Make sure that the power control unit is connected correctly in other words the cooker is connected to the OUT cable 4 INSTALLI2. 2 mace BNI tL L A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is switched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered If the element voltage of the cooker is 400 V the fuse can only be maximum of 10 A If the element is 230 V the fuse can only be maximum of 16 A Do not install the power control onit to excessive heat Operational ambient temperature is 5 t40 C N ATTENTION Power control unit requires a neutral wire to operate Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing the cooker or the power control unit see chapter 5 manual adjustment mode eh Remove the fuses to the cooker and oven Mount the power control unit on the wall behind the cooker or into the cabinet next to the cooker Install the power control unit with Perilex connectors 4 Put back the fuses for the cooker and the oven LEE 700 mm Veh W 146 mm Optional water sensor connection See chapter 4 126 mm 280 mm PCU5 1 U INSTALLATION nstanation Fixed 1 phase connection 230V MAX 25A MICRO DISCONNECTION or A WARNING Make sure t
3. NG THE WATER LEAKAGE SENSOR optional Stove Guard can be equipped with max four SAFERA water leakage sensors The sensors are placed in the typical leakage ar eas e g under the dishwasher or sink Attach the sensors in place amp Attach the plug of the leakage sen sor to the power control unit If there is an extra sensor its plug is connected to the connector of the previous sensor O Check the operation of the furthest sensor by placing a damp paper towel against it for 15 seconds When the water is detected the sensor unit gives a sound signal and indicator light will blink in blue Reset the leakage alarm by pressing the OK button Clean and dry the sensor w HINT If the sensor is left wet the appliance will give another alarm in 8 hours after signing off the previous one 5 MANUAL ADJUSTMENT MODE To enable the fast installation the default settings of SAFERA Airis are suitable for the most typical installations In case you need to install the sensor unit outside the default instal lation dimensions or replace the cooker sensor unit or power control unit in the original installation you need to enter the manual adjustment mode Press the adjustment button for 5 seconds and you will enter the first of the three manual adjustment modes Mode 1 Alarm limit settings Mode 2 Manual setup of the wireless connection Mode 3 Manual calibration of the
4. SAFERA SAFETY WITH STYLE INSTALLATION MANUAL SAFERA Airis Stove Guard Power Control Units PCU5 1 P Airis PCU3 Airis PCU3 W Airis PCU5 1 U Airis 20801 V4 5 0 ENG AIRIS CONTENTS 1 Preparations 2 Installation 3 Installation troubleshooting 4 Optional Installing the Water Leakage Sensor 5 Manual adjustment mode WARNINGS Follow these instructions carefully and pay particular attention to the instructions marked in the following way A WARNING Follow instructions marked with a warning accurately to prevent injury to persons and damage to property BE ATTENTION Follow instructions marked with a note carefully to prevent damage to property HINT Hints give you useful advices on using the appliance 1 PREPARATIONS A WARNING Read user and installation manual before using or installing the appliance Install and check the application according to the instructions SAFERA is not liable for any damages or expenses caused by inappropriate installation Check that the Stove Guard is compatible with the cooker see section 1 1 If the network cable is damaged it must be replaced by the service personnel of the manufacturer or their representative to avoid hazards All electrical connections must be carried out by a qualified electrician N ATTENTION If the appliance was stored in a cold space it must be allowed to warm up to room temperature before connecting it to elect
5. ance may fail to detect a hazardous situation in time 5 2 Mode 2 Manual setup of the wireless connection When the indicator light is blinking purple blue you may manually setup the wireless connection between the sensor unit and the power control unit for example when replacing either one of the units Take off the fuses for the cooker and oven for 10 seconds Put the fuses back the power control unit will now contact the sensor unit which gives a sound signal eee and the stove guard will automatically exit the manual adjustment mode To move to the manual adjustment mode 3 without changes in mode 2 press OK button 5 3 Mode 3 Manual calibration of the cooker type When the indicator light is blinking yellow green you may manually calibrate the cooker type from the two options OPTION 1 Cooker and oven are connected to the power control unit Or OPTION 2 Only cooktop is connected to the power control unit Turn on the oven and press the ad justment button When you hear a sound signal eee turn off the oven Turn on the biggest cooker plate with maximum power and press the ad justment button When you hear a sound signal eee turn off the cooker HINT With induction cooker use a compatible dish After calibration the stove guard will automatically exit the manual adjustment mode To exit manual adjustment mode 3 without changes pres
6. cooker type 5 1 Mode 1 Alarm limit settings When the indicator light will lit white you may adjust the alarm limit Check the closest recommended alarm limit from the reference table 1 below Adjust the alarm limit accordingly the default setting is 6 e You may raise the alarm limit 1 press the adjustment button 2 e You may lower the alarm limit 1 press the adjustment button 1 e After adjusting the the alarm limit the new alarm limit is indicated as shown in the table 2 on the right and the stove guard will automatically exit the manual adjustment mode To move to the manual adjustment mode 2 without changes in mode 1 press OK button Table 1 Recommended alarm limit reference table based on the location of the cooker and the installation height The range is 1 12 1 reacts fastest 12 reacts slowest Recommended Installation height Installation height alarm limit Mounting on the wall Mounting under the cooker hood 75 85cm 5 65 75cm 6 50 60 cm 55 65 cm 7 45 55 cm default Table 2 The new alarm limit is indicated as shown in the table below Color of the indicator light Number of beeps Alarm Limit 00o 08080 12 eee 0o 11 Red coco o 10 00o 9 ee 8 7 coe ooo 6 default eee oo 5 eee o 4 Blue wee 3 ee 2 1 A WARNING Do not set the alarm limit higher than 8 during the installation If the alarm limit is set too high the appli
7. e is loose it must be properly covered N ATTENTION Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing the cooker or the power control unit see chapter 5 manual adjustment mode Connect the stove with 3 pin plug Optional water sensor connection See chapter 4 Put back the fuses for the cooker and the oven INSTALLATION STEP 2 2 Mount the Sensor unit A Install the batteries Remove the mounting bracket from the sensor unit by pulling it gently Place the batteries in the sensor unit which should beep twice to indicate that the wireless connection to the Power Control Unit was successful e Place the mounting bracket back on it s place in the sensor unit ATTENTION Check the correct position of the batteries marked on the bottom of the battery case Mounting bracket with adhesive tape Adjustment button Adjustment button OK button Sensor direction Indicator light Sensors Low battery light Mount the sensor unit e Mount the sensor unit according to the mounting option A or B below if the cooker width is 70 90 cm add 10 cm the installation dimensions e Ensure the correct sensor direction both sensors should look towards the cooker see picture on the previous page The sensor unit should be mounted on t
8. hat there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is switched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered Do not install the Power Control Unit to excessive heat Operational ambient temperature is 5 t40 C N ATTENTION Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing the cooker or the power control unit see chapter 5 manual adjustment mode Remove the fuses to the cooker and oven Mount the power control unit on the wall behind the cooker or into the cabinet next to the cooker Couple the protective earth first PE Couple the other wires Put back the fuses for the cooker and the oven 9O0O 00 J Q f 7 am ee San OY Optional water OUT sensor connection 3 x 4 mm See chapter 4 PCU5 1 P INSTALLATION 3 pin plug IN OUT PE PE L N S 230V MAX 25A MICRO DISCONNECTION A A 60 mm 68 80 mm v v A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is switched off OUT wires are always energized when the power control unit is connected to the electrical network If a wir
9. he centerline of the cooker Use the cleaning pad to remove grease and dirt from the surface before attaching the sensor unit A with the adhesive tape Mounting option B cooker hood Mounting option A wall mount Allowed sensor unit position 90 8 Allowed sensor unit position 0 8 50 60 cm Centerline To install outside of the default installa tion height 55 65 cm adjust the alarm limit ac cording to chapter 5 Check the working order HINT Airis will automatically recognize the cooker type during cooking to minimize false alarms to speed up the auto recognition you may manually select the cooker type according to the chapter 5 3 e Press the OK button for 5 seconds to manually switch off the cooker power and test that none of the burners and the oven are powered e If ok press the OK button once 3 INSTALLATION TROUBLESHOOTING Problem Cooker cannot be turned on after pressing the OK button Faulty installation position of the sensor unit The wireless connection is not working The sensor unit is not responding to any button and none of the indicator lights are lit The appliance turns off the power from the cooker but the power comes back on immediately Remedy See user manual chapters 3 2 or 3 3 If the problem persists the appliace might be faulty Press the OK button to find out the problem type by the indicator light
10. ouple the protective earth first PE PE PE Couple the other wires L N N 230V 16A L3 Max 00 108 MICRO DISCONNECTION L L2 mvi tL mL x S 0O00 00 A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is switched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered If the element voltage of the cooker is 400 V the fuse can only be maximum of 10 A If the element is 230 V the fuse can only be maximum of 16 A Do not install the power control onit to excessive heat Operational ambient temperature is 5 t40 C Ei ATTENTION Power control unit requires a neutral wire to operate Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing the cooker or the power control unit see chapter 5 manual adjustment mode Put back the fuses for the cooker and the oven IN Q pe J2 5 x 2 5 mm AC v N Optional lt i water sensor 5x 2 5 mm connection 13m See chapter 4 PCU3 W INSTALLATION oS ALATON 3 phase Perilex connectors IN PE PE L N N 230V 16A P L3 max amp 400V 10A ar ee pees E MICRO DISCONNECTION L L
11. ric network 1 1 Compatibility SAFERA Stove Guard is compatible with most electrical cookers hobs and ovens meant for household use Traditional cast iron cookers and hobs Ceramic cookers and hobs Induction cookers and hobs Cookers and hobs equipped with a timer afterheat indicator child proof lock or integrated switch off system SAFERA Airis is compatible with cookers no wider than 90 cm see chapter 2 Instal lation step 2 2 1 2 Package content Check the product and the contents of the package before installation Power control unit various models available Transparent front cover 10 x Color labels Cleaning pad User and Installa tion Guides Optional mounting screws 2x Sensor unit with mounting LR6 bracket 2 x Batteries for sensor unit AA A WARNING Please contact your vendor if you notice anything unusual about the appliance INSTALLATION STEP 1 2 Mount the Power Control Unit Install the power control unit according to the following instructions PCU3 PCU5 1 U Fixed 3 phase connection si Fixed 1 phase connection See pages 6 7 See pages 10 11 PCU3 W PCU5 1 P Perilex connectors i 3 pin plug See pages 8 9 See pages 12 13 PCU3 INSTALLATION i ii Fixed 3 phase connection Remove the fuses to the cooker and oven Mount the power control unit on the wall behind the cooker or into the cabinet next to the cooker C
12. s OK button once and the stove guard will exit the manual adjustment mode
Download Pdf Manuals
Related Search